Search Documents

By Kirk Ellison, Sherif Elfass, Ramin Motamed, Kevin V. Stanton

"The determination of accurate load transfer curves are essential for estimating deep foundation loadsettlement response using t-z style analyses. While recently developed semi-empirical methods from Ashour et al. (2010) and Ashour & Helal (2012) have shown promise in preliminary studies, they have not yet been thoroughly benchmarked against a more widely accepted approach. To address this issue, these recent procedures are implemented in the computer program CGI-DFSAP to predict the results of four Osterberg-cell (O-Cell) load tests. These predictions are compared to outcomes obtained following the recommendations from Reese & O’Neill (1988) for t-z analyses of drilled shafts in sand and clay which are carried out with the program TZ-PILE. Overall, the results suggest that the new approach offers improved accuracy regarding predictions of drilled shaft response to axial loading.INTRODUCTIONThe behavior of axially loaded deep foundations is often analyzed using a technique known as the t-z method. In this method, deep foundation elements are broken into multiple segments which are supported by discrete nonlinear springs to capture the contribution of both side-friction (t-z springs) and end-bearing (Q-z springs). Hence, the t-z and Q-z relationships dictate the predicted load-settlement response. A number of different approaches have been developed to estimate load-transfer curves with some relying solely on empirical data from laboratory and field experiments (i.e. Coyle & Reese, 1966; Vijayvergiya, 1977) and others based mainly on analytical frameworks (i.e. Kraft et al., 1981; Randolph, 1994). Reese & O’Neill (1988) provide recommendations which are widely used for developing t-z and Q-z curves for analyzing drilled shafts. This method is hereafter referred to as Method 1 (M1). It should be noted that these empirically derived relationships are only applicable for problems associated with drilled shafts and are therefore not appropriate for developing load-transfer curves for other types of deep foundations (i.e. driven piles). This is because of the difference in the frictional resistance which can be developed between a circular concrete-soil interface as opposed to that of other materials (i.e. steel) and/or different cross sectional geometries.The M1 load-transfer curves form the basis for the t-z analysis of drilled shafts implemented in the computer program TZ-PILE (Ensoft, 2014). In light of this, TZ-PILE is employed herein as a reference to compare against the capabilities of another method of implementing t-z style analyses. This method is based on a semi-empirical framework for soil behavior developed by Norris (1986) and is implemented using the program CGI-DFSAP (Computers & GeoEngineering Inc., 2011). More information concerning this approach, hereafter referred to as Method 2 (M2), is given in subsequent sections."

Jan 1, 2017

By S. D. Graham

"The extractive metallurgy of gold is largely controlled by mineralogical factors such as the presence of refractory gold, particle size, gangue mineral associations, presence of preg-robbers, oxygen and cyanide consumers, and locking characteristics in base metal sulphides. Light microscopy and automated mineralogy techniques are regularly used to characterise the effect of these variables on gold recovery. However, despite their widespread application there are a range of limitations when grades are low. Typically, the analysis of low-grade samples requires the preparation and analysis of numerous polished blocks. This is often costly and time consuming, with complexities regarding analysing statistically representative particle quantities and problems overcoming stereological bias. This is compounded by the “nugget” effect and high tenor nature of gold mineralisation. X-ray Microscopy techniques have the potential to overcome many of these problems, in particular the statistical representivity of analysis, removing stereological bias and effectively locating phases that are present in ultra-trace proportions. In this paper we outline the potential benefits of employing X-ray Microscopy (XRM) in characterising gold losses from a typical Cu-Au porphyry project, which were illusive in 2D based analysis. The talk will also outline additional application areas of XRM within the extractive value chain."

Jan 1, 2017

By M. J. U. T. Van Wijngaarden, R. J. Dippenaar, P. M. Van Den Heever

Some of the important properties of solid electrolytes that influence the performance of electrochemical oxygen probes are discussed in the first part of this paper. It is shown that accurate and reproducible measurements of oxygen in liquid steel are possible with commercial oxygen probes only if great care is exercised in the make-up of the chemical and phase composition, as well as the microstructure of the solid electrolytes used in these probes. To prove this premise, the second part of this study reports on the results of an experimental evaluation of new commercially available oxygen probe. An evaluation of the solid electrolytes used in this probe indicated that the consistency of the chemical composition, degree of stabilization, and microstructure of the electrolytes used are well controlled. The successful application of this particular oxygen probe under industrial conditions was confirmed. It was also found possible to make reliable and reproducible measurements, with acceptable uncertainty, by proper handling of the probe. Some recommendations are made as to the interpretation of the e.m.f. response curve and the use of the electronic processing unit supplied with the probe.

Jan 1, 1987

By Randy Clarkson

Sluiceboxes which are designed and operated as recommended from our recent research can provide much higher concentration ratios than most other gravity concentrators (up to 50,000: 1) at very high overall placer gold recoveries (95-99%). They are also very reliable, inexpensive and simple to operate. A sluice­box is a rectangular flume containing riffles on matting, through which a dilute slurry of water and gravel flows. However, sluiceboxes operating under ideal conditions are actually cen­trifugal concentrators whose riffles overturn ribbons of slurry to form vortices. At the bottom of these vortices, centrifugal and gravitational forces combine to drive gold particles into matting (figure 1).

Jan 1, 1996

By A Jewbali, L Allen

At Newmont Corporation drill hole spacing studies are done to support the business in understanding the cost of collecting additional information (with a specific focus on drill hole sampling density) versus the value of additional drilling in terms of resource risk reduction. For the last 20 years drill hole spacing studies have been executed in an effort to answer the following question: What spacing should the deposit be drilled at to achieve a certain level of resource confidence so that when mining occurs the resource model delivers as predicted ie what is the optimal sampling density? The optimal sampling density supports a resource model that provides a sound foundation for mine planning purposes and resource/reserve reporting. At Newmont Corporation drill hole spacing studies are now a requisite for understanding drill data density needs for new deposits and near mine expansions. This paper details the evolution of drill hole spacing studies at Newmont Corporation in terms of methodology and usage.

May 24, 2023

By Brian L. Quick

Problem: The National Institute for Occupational Safety and Health's [NIOSH] National Occupational Research Agenda (DHHS Publication No. 96 115) reports that approximately 50% of miners will experience hearing loss by age 50, compared to only 9% of the general population. The present investigation examines three antecedents believed to be associated with miner's use of hearing protection. Method: A posttest delayed posttest control group field research design was employed to assess antecedents toward wearing hearing protection. Results: Following the initial posttest, miners' attitudes and subjective norms were antecedents to intentions to wear hearing protection devices. Also, intentions toward wearing hearing protection predicted hearing protection behaviors. Approximately six weeks later, miners' attitudes and perceived behavioral control were each significant predictors of intentions to wear hearing protection and again, intentions were positively associated with hearing protection behaviors. Impact on Industry: Our results indicate that appeals to normative influences may be the most effective antecedent to employ when persuading coal miners to wear hearing protection. However, messages designed to impact attitudes and perceived behavioral control were also effective.

Jan 1, 2008

By D. R. Willmer, E. J. Haas

"DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT This study analyzed the publicly available health and safety policies of 26 mining companies to determine the quantity of health and safety (H&S) practices that mining companies encourage in relation to the Plan-Do-Check-Act cycle. A thematic content analysis of the policies identified elements and practices within the text. On average, companies communicated information on about 7 elements (range 1–14, standard deviation = 3.49) and discussed 15 practices (range 2–34, standard deviation = 9.13). The elements in which companies highlighted the most practices were risk management, emergency management, leadership development, and occupational health. A discussion of the policy trends shows areas that mine sites can improve upon within their Plan-Do-Check-Act cycle, in addition to encouraging the use of both leading and lagging indicators to manage health and safety performance. INTRODUCTION Mining companies and their employees are expected to identify and manage risks at their worksites to ensure the health and safety (H&S) of everyone at the site. The primary mechanism in place to control these risks is a company’s health and safety management system (HSMS) (Boyle, 2012). Broadly, an HSMS is a set of standard, interrelated, and interacting elements used to promote and achieve occupational H&S goals (ANSI/AIHA Z-10, 2012; BS OHSAS 18001, 2007). The practices conveyed within an HSMS are expected to minimize incidents, injuries, illnesses, and even save worker lives (Alsop and LeCouteur, 1999; Arocena and Núñez, 2010). In the United States, both the Occupational Safety and Health Administration (OSHA) and Mine Safety and Health Administration (MSHA) regulate and encourage aspects of an HSMS (US Federal Register, 2011, 2010). Many HSMS documents (i.e., Chemical Industries Association, 1995; Health and Safety Executive [HSE], 1995; International Labour Office [ILO], 2001) attribute the source of their basic management system to Deming’s Plan-Do-Check-Act (PDCA) model of continuous quality improvement and organize their practices within this cycle (Johnson, 2002). The PDCA cycle is a well-adopted approach in health and safety management and promotes continuous learning and adaptability (Robson et al., 2007)."

Jan 1, 2018

By R. L. Veenstra

This paper explores the connection between the stresses observed and the failure mechanisms present in the modelled cemented paste backfill. In order to look at this connection, the authors have used a previously developed model to conduct a sensitivity analysis of the model?s strength and permeability input parameters. The results from the sensitivity analysis were then compared to determine what causes modelled stresses and failure mechanisms to vary. Increased insight into the behaviour of the modelled paste will help clarify how paste behaves in the field.

Aug 1, 2013

By V. K. Gupta

Several approaches to the estimation of the size discrete breakage rate and distribution parameters (kj and bi,j ) of the batch grinding kinetic model are available in the literature. Analysis of a large amount of data available in the literature and our own data on several pure minerals and complex ores has shown that it is not always possible to obtain correct estimates of the two sets of parameters using known approaches as several widely different combinations of k and b parameters can sometimes simulate the batch grinding data reasonably accurately. It has been found that there are two main reasons: (i) all size classes are not well represented in the data and (ii) functional forms used for estimation of the two sets of parameters are sometimes chosen somewhat arbitrarily (especially in the case of complex ores), though they are actually uniquely related through size continuous breakage rate and distribution functions. A suitable experimental methodology has been described and demonstrated using some synthetic data and actual experimental data. A mill function approach, which does not require making any assumptions about the functional forms for k and b parameters, is also described and demonstrated. This approach is promising, but requires further development.

Sep 1, 2012

By Daniele Martinelli, Rodrigo Winderholler, Daniele Peila

"This paper presents a technical description of an experimental procedure developed for the geotechnical characterization of granular soils conditioned for EPB tunneling using a modified direct shear box. As the main concerning parameters of the conditioned soil mass were their undrained properties, in order to preserve its pseudo-fluid characteristics, a watertight direct shear apparatus was constructed. A comparison between the results obtained under dry, saturated and conditioned conditions is presented. INTRODUCTION EPB shield machines have been used for tunneling excavation in many different types of soils thanks to the use of soil conditioning agents. These modify the properties of the soil into that of a plastic paste, thus permitting the homogeneous flow of the excavated soil from the tunnel face through the bulk chamber, the screw conveyor and finally the conveyor belt. Moreover this technique allows controlling the face pressure and its regulation in the bulk chamber, preventing water inflow when tunneling below the water table. Further advantages are a drop of the cutter head and screw conveyor torque and reduction of the friction between metallic parts and the soil, consequently reducing wear phenomena (Merritt & Mair, 2006; Vinai et al., 2007; Borio et al., 2010; Thewes & Budach, 2010; Herrenknecht et al., 2011; Barbero et al., 2012; Peila, 2014). Several studies have investigated the possibility of conditioning and the chemical materials to be used in different types of soils, mainly subdivided into three groups: cohesionless soils (sand and gravel), silts and clays, and rock masses. This various researches have set up several laboratory procedures for these achievements before and after soil conditioning, as stated in Thewes & Budach (2010) and Peila (2014) (for cohesionless soils), in Thewes & Burger (2005), Hollmann & Thewes (2013), Zumsteg et al.(2012) (for clay), in Peila et al. (2013) and Martinelli et al. (2015a) (for rock mass). Such tests should be simple to execute, reliable and easy to interpret at the in-situ excavation step. The reduction of shear strength is necessary in EPB operations, since it allows an effective transmission of the pressure from the material itself to the front. In some cases the slump is not sufficient to return a reliable result on the shear strength reduction, as in some cases some materials are behaving differently. Therefore this research is aimed to study this aspect more in detail, in order to show the effectiveness of the soil conditioning process on the material to be excavated."

Jan 1, 2016

From March to May of 1963, the Bureau of Mineral Resources carried out an experimental aeromagnetic survey at Cobar, New South Wales, to field test a proton-precession magnetometer installation in the Cessna aircraft VH-GEO. The Cobar area was chosen as considerable information was already held on the Earth's magnetic field there, which was known to provide a range of anomalous areas that are not excessively disturbed.A procedure for survey flying and methods for processing data were developed during the survey. Contour maps of the aeromagnetic results were produced in the field. The experimental survey was successful in outlining magnetic anomalies in detail.INTRODUCTIONSince 1951 the Bureau of Mineral Resources, Geology and Geophysics (B.M.R.) has carried out an airborne magnetometer exploration programme with DC.3 aircraft carrying fluxgate magnetometer equipment. Recently a proton-precession magnetometer was developed by the Design and Development Group of the B.M.R. for observatory use. One unit modified for airborne use was installed in the Cessna light aircraft, VH-GEO. The Cessna was modified structurally to take the magnetometer, associated bird, and winch gear.The proton-precession magnetometer has many good features.1. It utilises the transistor and associated solid-state devices in its electronics, and hence is light and small.This is the basic feature allowing its installation in a light aircraft. The transistor circuits have a high reliability factor and owing to the card sub-unit...

Jan 1, 1964

By Susanna A. C. Stadler, Chris Aldrich, Jacques J. Eksteen

Slag foaming occurs in several pyrometallurgical processes. These processes include steelmaking in basic oxygen steelmaking furnaces and electric arc furnaces as well as various non-ferrous operations like sulphide smelting/converting and base metal slag cleaning. Although slag foaming in steelmaking processes has been extensively researched, little attention has been given to slag foaming in non-ferrous operations. Slag foaming phenomena are complex because often the system consists of three or more phases. With this in mind, factors previously identified as influencing slag foaming were investigated. These include the slag basicity, physical properties of the slag, namely viscosity, surface tension and density, the formation of particles due to undercooling of the slag and the FexO concentration in the slag. The effect of increasing FexO concentration was found to decrease the foam index due to lower viscosities, but higher surface tension depression appears to have led to increased foam index values at high FexO concentrations. The foaming index decreases with increasing basicity, until precipitation of solids occurs. After this point, the foaming index was found to increase with increasing basicity due to increased solids precipitation. In general, increasing amounts of slag-wettable solids led to higher foam indices, but the precise nature of the effect on slag foaming was dependant on the nature of the solid precipitate.

Jan 1, 2003

By R. Hazael, R. Alford, R. Critchley

The ability to compare explosives is fundamental. Numerous methods are used and while simple conversion factors are often used, the use of TNT Equivalency (TNTe) is not a simple subject as explosives exhibit very different equivalencies depending on whether the pressure or impulse are being considered as well as other conditions. The scaled distance has been found to have a significant effect on the TNTe but due to the difficulty of taking measurements at very close ranges, no TNTe have been quoted for charges in direct contact (Z=0). This paper describes the use of a ballistic pendulum to measure the impulse from contact charges and presents some surprising results that require a two-stage propulsion, as originally described by Backofen, to be explained.

Jan 1, 2024

By Margreth Tadie, Chalwe Chibwe

Physicochemical properties of copper electrolytes are a strong fundamental consideration in electrodeposition processes during electro-purification and recovery of copper. Their influence extends to mass transfer as well as energy consumption during the electrodeposition process. In this study, the influence of electrolyte composition on electrolyte physicochemical properties was investigated to review the existing literature data. This review of data is considered necessary as more and more electrowinning models are being developed for process prediction and optimisation and a need of such data is required for accurate prediction of physicochemical properties. The major components of importance to the formation of smooth high-quality and high-purity copper cathodes at optimum current efficiency are considered the species in solution. These include Cu ions, Fe ions (major impurity), H2SO4, and a smoothing agent additive. A 5-factor, 2- and 3-level experimental design was employed to determine the effect of copper (35 and 45 g/l), sulphuric acid (160 and 180 g/l), iron (1, 3, and 6 g/l), polyacrylamide additive (2, 5, and 10 mg/ l), and temperature (45 and 55 °C) on electrolyte density, conductivity, and the diffusion coefficient in synthetic copper electrowinning electrolytes. The major species in a copper electrowinning electrolyte are found to be the most relevant for prediction of physicochemical properties. These results indicate that relatively simple empirical models are sufficient for modelling of the electrolyte domain in electrowinning, without the need for the generation of vast amounts of complex experimental data.

Feb 1, 2021

By M. Nilmani, J. Sofra

The transverse distributions of the solids discharge velocity and mass flux at the discharge end of vertical and inclined lances were measured in order to detennine the transverse distributions of the axial momentum flux, which is a dominant factor influencing the penetration behaviour of particles into melts during submerged injection. The effects of gas velocity (10 - 30 m/s), solids loading (5 - 10), lance length (0.15 - 1.0 m), lance inclination (vertical downward - horizontal) and particle density (2500 - 8900 kg/m3 ) were investigated, while the lance diameter and particle size were fixed at 10 mm and 220 µm respectively. The particle velocities and mass fluxes were measured by image analysis of particles illuminated in a laser-generated light sheet aligned vertically through the axis of the lance at the discharge point. The particle discharge velocity profiles for vertical downward flows were synunetrical about the centre-line of the lance, with the maximum velocities occurring at the centre-line. The velocities increased with increasing gas velocity, increasing lance length and decreasing particle density in accordance with previous observations. The transverse mass flux profiles were also synunetrical for vertical downward flows, however at the lower gas velocities the peaks in the profiles were displaced from the centre-line of the lance by a fractional diameter of about 0.15. The particle discharge velocity profiles become increasingly asynunetric as the lance orientation was changed from vertical to horizontal, with higher particle velocities present near the top wall of the lance. The mass flux profile also became asyrrunetric as the horizontal orientation was approached, however in this case, the profile became biased towards the bottom of the lance. The effect was much more pronounced for a gas velocity of 10 m/s than for 30 m/s, showing the relatively stronger gravitational influence as the velocity was reduced.

Jan 1, 1996

By A. V. Z. Brink

Rock engineering risk is defined in this paper as a function of the potential ground motion; the vulnerability of the workplace; exposure of people; and a general term – quality of information. The paper describes the development of prototype software that is a combination between an expert system approach for determining overall risk assessment, a risk control recommendation and a basic GIS (Graphic Information System) approach for graphically overlying input parameters and the output risk. The expert system uses a Bayesian probabilistic approach to combine various workplace-related information, a quantified seismological environment and the exposure of underground staff to provide an overall RE risk rating. The risk assessment is dynamic in that it is recalculated each time that any of the input parameters change, for example each time a seismic event is recorded in the area of interest. The code was tested on a data set from Savuka Gold. As risk assessment is not an absolute prediction of a specific outcome, it is therefore not possible to relate to individual case studies and the reliability of this method would only be determined after an extensive period of use with appropiate back-analysis. Le risque dans le génie minier est défini dans cette étude comme une fonction du mouvement potentiel de terrain ; la vulnérabilité du lieu de travail ; l’exposition des personnes ; et un terme général – la qualité de l’information. L’étude présente décrit le développement d’un logiciel prototype qui est une combinaison entre une démarche de système expert pour déterminer une évaluation générale du risque, une recommandation pour le contrôle du risque, et une démarche de SIG (Système d’Information Géographique) pour superposer graphiquement les paramètres d’entrée et le risque de sortie. Le système expert utilise une méthode de probabilité bayésienne pour combiner des informations variées sur le lieu de travail, des données quantifiées sur l’environnement sismique, et l’exposition du personnel travaillant sous terre, pour finalement produire un classement général de risque minier (RE). L’évaluation du risque est dynamique en ce sens qu’elle est recalculée à chaque fois qu’un des paramètres d’entrée change, par exemple à chaque fois qu’un évènement sismique est enregistré dans la région. Le code fut testé sur un ensemble de données obtenues de Savuka Gold. Comme l’évaluation du risque ne constitue pas une prédiction absolue d’un résultat spécifique, elle est par conséquent difficile à rattacher à des cas individuels et la validité de cette méthode ne pourrait être déterminée qu’après une longue période d’utilisation avec analyse rétrospective appropriée. Das Gesteinstechnikrisiko wird in dieser Arbeit als Funktion einer möglichen Bodenbewegung definiert; die Anfaälligkeit des Arbeitsplatzes; das Ausgesetztsein der Belegschaft; und ein genreller Begriff - Qualität der Informationen. Das Papier beschreibt die Entwicklung einer Prototyp-Software, die eine Kombination zwischen einem Expertensystemzugang für die Bestimmung der gesamten Risikobeurteilung ist, eine Empfehlung zur Risikokontrolle und eines fundamentalen GIS (graphisches Informationssystem) Zuganges für graphisch darüberliegende Eingangsparameter und das Outputrisiko. Das Expertensystem verwendet eine bayesische Wahrscheinlichkeitsannäherung, um verschiedene mit dem Arbeitsplatz in Verbindung stehende Informationen, ein quantitativ bestimmtes seismologisches Umfeld und das Ausgesetztsein des Untertag-Personals zu kombinieren, um eine gesamte RE-Risikobewertung zur Verfügung zu stellen. Die Risikobeurteilung ist insoferne dynamisch,daß sie stets nachkalkuliert wird wenn sich irgendeiner der Eingangsparameter ändert, z.B. jedesmal wenn ein seismischer Fall im Interessensbereich aufgezeichnet wird. Der Code wurde auf einem Datenbestand von Savuka Gold geprüft. Da die Risikobeurteilung nicht eine absolute Vorhersage eines spezifischen Resultates ist, es ist folglich nicht möglich, sich auf einzelne Fallstudien zu beziehen und die Zuverlässigkeit dieser Methode könnte nur nach einer umfangreichen Benutzungsdauer mit geeigneter Postanalyse bestimmt werden.

Jan 1, 2003

By John D. Carriere, Jean Leung, Daniel. Laguitton, Michael .. J. Burrows

"The objective of this expert system application in a copper-zinc concentrator, is to increase the availability of assay data through substitution for erroneous data. The assay data is used by the Operations personnel and automatic process control strategies to control flotation circuit performance. Two online X-ray fluorescence analysis systems analyze 24 streams across four divisions to provide the required data. Data availability of individual streams average 90% while the resulting circuit availabilities are 70%. The unavailability of correct data results from mechanical, X-ray or process problems. The erroneous data can be identified by process experts using knowledge relating stream interdependencies and historical process behaviour. An expert system was devised to provide real time identification of erroneous data and substitute for that data with the ultimate aim of improving metallurgical response by both the operator and automatic control systems.The paper discusses the early development work and architecture of the knowledge base designed using Neuron Data's expert shell NEXPERT.INTRODUCTIONThis paper describes the early development of an expert system (ES) prototype at the Kidd Creek concentrator. The project is a joint undertaking of the Kidd Creek Division of Falconbridge Limited and CANMET. Kidd Creek entered into the project to apply heuristic rules to the XRF assay data to improve the metallurgical control of the flotation process by increasing availability of analysis data. This project provided a problem of suitable size and future expandability while making use of a wide base of in-house expertise and experience. Another important benefit is the introduction of expert system technology to the site providing tools and experience for future system selection and technology application. CANMET has an on-going interest in assessing various aspects of ES technology (hardware, software, knowledge engineering, integration) while addressing problems in process operations that could most readily benefit from the technique. CANMET's role in the project was to provide project assistance, financial support, substitution algorithm assistance and software for data substitution. The knowledge bases (rules) have now been completed and are to be tested in the online environment."

Jan 1, 1989

By Dani J. Alldrick, Alastair J. Sinclair, Colin I. Godwin

"Abstract - The Stewart mining camp has a long history of precious and base metal mining. The camp is abundantly mineralized, with more than 200 widespread, varied, vein prospects, deposits and orebodies. These show wide variations in the mineralogy of ore, gangue and alteration assemblages, and wide variations in textures and structural settings. This report establishes the timing of the different metallogenic epochs and suggests a specific exploration application for systematic lead isotope analyses.Galena lead isotope ratios from a range of mineral occurrences indicate that all these varieddeposits formed during two main mineralizing events. Lead isotope data from the Stewart mining camp do not provide absolute ages for the formation of mineral deposits, but the relative distributions of data are consistent with dates determined in other studies. One ore-forming episode occurred in the Barly Jurassic and the other in the Middle Eocene. Both metallogenic epochs were brief, regional-scale phenomena. Sorne deposits from the younger mineralizing episode were em­ placed adjacent to or superimposed on the older deposits.Field and laboratory studies show that the two metallogenic epochs are characterized by different base and precious metal suites: Barly Jurassic gold-silver-zinc-lead-copper; and Middle Eocene silver-lead-zinc. Therefore, showings of different ages have different base and precious metal potentials and deserve different exploration emphasis. Lead isotope studies provide a reliable, cost-effective method for evaluating the age and commodity potential of small or recently discovered mineral showings and for setting exploration priorities on properties with several varied mineral occurrences . The determination of the age and metal potential of a prospect at an early stage of exploration may govern the urgency, intensity or even the necessity for further exploration work."

Jan 1, 1993

By Dani J. Alldrick, Alastair J. Sinclair, Colin I. Godwin

"The Stewart mining camp has a long history of precious and base metal mining. The camp is abundantly mineralized, with more than 200 widespread, varied, vein prospects, deposits and orebodies. These show wide variations in the mineralogy of ore, gangue and alteration assemblages, and wide variations in textures and structural settings. This report establishes the timing of the different metallogenic epochs and suggests a specific exploration application for systematic leadisotope analyses.Galena lead isotope ratios from a range of mineral occurrences indicate that all these varied deposits formed during two main mineralizing events. Lead isotope data from the Stewart mining camp do not provide absolute ages for the formation of mineral deposits, but the relative distributions of data are consistent with dates determined in other studies. One ore-forming episode occurred in the Early Jurassic and the other in the Middle Eocene. Both metallogenic epochs were brief, regional-scale phenomena. Some deposits from the younger mineralizing episode were emplacedadjacent to or superimposed on the older deposits.Field and laboratory studies show that the two metallogenic epochs are characterized by different base and precious metal suites: Early Jurassic gold-silver-zinc-lead-copper; and Middle Eocene silver-lead-zinc. Therefore, showings of different ages have different base and precious metal potentials and deserve different exploration emphasis. Lead isotope studies provide a reliable, cost-effective method for evaluating the age and commodity potential of small or recently discovered mineral showings and for setting exploration priorities on properties with several varied mineral occurrences. The determination of the age and metal potential of a prospect at an early stage of exploration may govern the urgency, intensity or even the necessity for further exploration work."

Jan 1, 1993

By Mahmud Esad Uluer, Seyed Hassan Amini, Aaron Noble, Matt Shigo

Airborne coal mine dust is an unintended and unavoidable result of coal extraction operations that raises notable health and safety concerns. Modern mining techniques utilize several dust mitigation strategies, and the flooded-bed dust scrubber (FBS) is one such technology used extensively on continuous miners. The conventional static panel filter, instrumental in most scrubber designs, is fundamentally limited in collection efficiencies due to a high clogging rate and a tradeoff between mesh density and airflow rate. To overcome these deficiencies, a novel vibrating mesh panel is proposed. In this study, a laboratory-scale dust scrubber unit was used to investigate the efficacy of concept as compared to that of a static mesh. A statistical design of experiments study was first used to determine the effective vibrational parameters and scrubber operational parameters on dust collection and clogging mitigation. Optimized results from this study were then evaluated against those of a static mesh to determine performance improvement while investigating the mechanisms controlling dust collection and particle department through the scrubber system. Results show that the vibrating mesh conditions and higher water flow rates led to an improvement in the collection efficiency of the scrubber system. Compares to a static-mesh, the vibrating mesh FBS showed a significant reduction in pressure drop across the mesh screen indicating lower air loss through the test duration. Overall, the findings confirm that vibrating filter mesh reduces filter clogging while maintaining high collection efficiencies. This research supports further technological advancement in mine dust mitigation technologies.

Dec 27, 2023