Search Documents

By Kenneth K. Humphreys, Joseph W. Leonard, Robert L. Llewellyn, William F. Lawrence

INTRODUCTION Cleaning fine coal sizes utilizing air currents in machines as the primary separating medium is called dry concentration or pneumatic cleaning. In 1947 approximately 18 million tons (16.38 million mt) of bituminous coal were cleaned by air machines; in 1965, 25.4 million tons (23.1 14 million mt); but in 1975, only 7 million tons (6.37 million mt). Table 11-1 shows the tonnages cleaned of bituminous coal and lignite in the United States by various types of equipment from 1938-1963. Table 11-2 shows only tonnages cleaned by pneumatic methods from 1964-1975. The decrease in tonnage to approximately 7 million tons (6.3 million mt) is due to a higher moisture content in the mined coal and the greater difficulty in cleaning the coal by air. There also was a definite trend to load raw coal at the mines, especially the slack which is the most expensive to clean due to the dewatering and drying requirements. While there have not been any applications of pneumatic cleaning in the anthracite field, its use has not been fully explored. The same is true for lignite and subbituminous coals.

Jan 1, 1979

By C S. Kelsey, J R. Kelly

Australia is presently enjoying the fruits of a booming iron ore market. Expectations are that market strength will be supported in the short to medium term by increasing feedstock demands from steel mills, as world economies rebuild post-Covid-19. However, as cost and environmental pressures increase the longer-term market outlook will be dominated by product quality. The ‘flight to quality’ will place increasing demands on direct shipping ore miners as they compete to maintain their standing in the iron ore marketplace. China will progressively disengage from its dependence on Australian imports, leaving miners under increasing pressure to boost product quality and diversify outlets globally. Australia has vast deposits of low-grade magnetite ores located mainly in remote and arid regions of the continent. This paper proposes a dry grinding and magnetic separation process to produce premium concentrate grades from the low-grade ores, to assist in meeting future product quality demands. The premium grade concentrates could be either blended with lower quality direct shipping ores or marketed separately. The proposed dry concentration process involves the pairing of Vertical Roller Milling (VRM), a mature technology widely used in the cement industry, and Planar Magnetic Separation (PMS), a new methodology, which has been developed to the threshold of commercialisation by the private Australian company Cyclomag P/L. Two laboratory prototype planar magnetic separators with field strengths of 1800 gauss and 6000 gauss have been built and tested on a range of magnetite ore types over the past three years. In each case, following grinding to liberation sizes, a combination of roughing and cleaning operations has produced pellet grade concentrates. Vertical roller milling has competed successfully with conventional media milling in grinding cement clinker, limestone and blast furnace slags. A key advantage of dry VRM/PMS processing is its potential adaptability to stepwise modular development, which can minimise initial capital investment, while generating early revenue streams to cope with unpredictable market volatility.

Nov 8, 2021

By E. M. De Souza

"A scientific testing program, sponsored by the Mining Industry Research Organization of Canada (MIROC), was undertaken on the surface and underground facilities of Inca's Crean Hill Mine to investigate the effectiveness of using dry drilling with a dust control system.The surface test work consisted of the monitoring of advance rates and bit life white a series of 165 mm holes, wet and dry, were drilled at both mine air (0.69MPa) and high pressure air (1.72MPa). The results, based on statistical evaluations of field data, indicated that penetration rates can be increased by an average of 24% when drilling dry with high air pressure and by approximately 27.5% when drilling dry with mine air as compared with wet drilling under the same conditions. Dry drilling also has the effect of reducing button wear by approximately 69% using high pressure air. The underground test work employed a dust collection system developed for use with large diameter holes (165 mm) and high pressure drilling. The testing program has indicated that an average increase in penetration rate of 35% can be achieved when dry drilling in rock (waste) and of 49% when dry drilling in ore with high air pressure. Although preliminary dust monitoring did not indicate any appreciable increase in dust concentration during dry drilling, further dust monitoring is still required.A comparative cost analysis has indicated the potential for reduction in drilling costs when dry drilling is utilized. Further testwork is to be conducted to develop a reliable dust collection system for underground production."

Jan 1, 1992

Develop a dry dust collector suitable for working faces and belt transfer paints. Approach A filter cartridge with a reverse-pulse, self-cleaning system has been mounted in-to a low profile unit requiring electric power only. How It Works Dust-laden air entering the in-let end of the collector passes through the two inline filter elements. When the elements load to a pre-selected pres-sure drop, they are automatically pulse-cleaned by a "backflush" method using compressed air. When the elements are pulse-cleaned, caked dust material on the filter surface is released, and falls away as lumps. Dust is removed from the collector by an auger mechanism. Features of the collector are: (1) unit is completely self-contained, (2) built-in air compressor for pulse-cleaning, (3) cleaning cycle initiates automatically at a preset restriction, (4) automatic auger discharge of collected dust, (5) detachable extension auger for transporting collected dust, (6) "dust leak" indicator light, and (7) "change filter element II warning light. The collector has been designed as permissible although approval has not yet been granted.

Jan 1, 1981

Develop an alternative to water bath exhaust conditioners (water scrubbers) for permissible diesel equipment used in gassy mines. Background Water scrubbers are a safety device used on diesel-powered vehicles in gassy mines. Exhaust from the engine passes through the scrubber, where it is cooled, and any flames or sparks present in the exhaust are extinguished. This prevents the ignition of combustible mine dust or methane that may be present. Unfortunately, water scrubbers consume large amounts of water and require frequent maintenance. Approach Methods that do not require water replenishment and frequent maintenance were investigated. The dry exhaust conditioning system was selected for investigation because no water is consumed and existing heat exchanger technology can be adapted to underground mine vehicles. In accordance with U.S. Mine Safety and Health Administration (MSHA) requirements, the system was designed to cool exhaust and trap flames and sparks. The U.S. Bureau of Mines (USBM) developed and evaluated a system for large engines and evaluated a second system for smaller engines. Both systems were evaluated on an engine test bed; if warranted, the system was then tested underground.

Jan 1, 1993

By D. Tao

Coal is a major source of energy in the U.S. and more than 51% of the electricity used in the country is generated from coal. Coal cleaning prior to combustion is necessary and often accomplished using wet physical processes at coal preparation plants to remove impurities such as ash, sulfur, mercury. However, the resultant clean coal product still contains a significant amount of impurity due to the fact that impurities are not well liberated from coal particles ranging from several millimeters to inches in size at which wet cleaning processes take place. A cleaner coal product can be obtained if a cost-effective dry process is developed to further clean pulverized and thus better liberated fine coal at the power plants prior to its combustion. The benefit of such a process is a significant reduction in the cost of expensive post-combustion chemical cleaning processes such as flue gas scrubbing employed to meet the stringent environmental air quality regulations. In this study, a novel rotary triboelectrostatic separator (RTS) was investigated for its application to dry cleaning of fine coal samples acquired from the power plants in the state of Illinois. The pulverized fine coal contains well liberated ash and pyrite minerals and is an ideal feed to the triboelectrostatic separator for further cleaning without the use of water or any chemical reagents. The proprietary rotary triboelectrostatic separator (RTS) is characterized by an innovative high efficiency rotary charger, charger electrification, laminar air flow, and specially designed electrodes. Compared to existing triboelectrostatic separators, the rotary triboelectrostatic separator offers significant advantages in particle charging efficiency, solids throughput, separation efficiency, applicable particle size range, etc. Testing with several fine coal samples has demonstrated that this technology can significantly reduce ash content with a process efficiency similar to or better than froth flotation. Important process parameters such as charger rotation speed, injection and co-flow rate, feed rate were investigated for their effects on separation performance.

Jan 1, 2010

By Egbert Burchardt

"Some of the challenges faced by the mineral industry in the future are the need to process low grade ores at the lowest operating cost, to deal with elevated energy cost and to address scarce water resources in some regions of the world. These challenges will increase the demand to develop highly energy-efficient and less water-consuming mineral processing systems. Experience from other industries suggests that HPGRs could help to achieve these goals, due to their high energy efficiency and their ability to be used as dry grinding systems. Historically, HPGRs have been used mainly as tertiary crushers in mineral applications for the production of ball mill feed. In the cement industry, however, HPGR systems have been successfully applied for grinding limestone, clinker and slag to a final product fineness (p80) of between 30 and 90 µm without the need of downstream ball milling. The total energy consumption of HPGR finish grinding systems in the cement industry has been found to be 30 to 50 % lower than in ball mill systems. This leads to the question of whether the same methodology can be adopted in the mineral industry. Such a step would require the use of dry rather than wet grinding systems. Traditionally, dry grinding systems have been only an exception in mineral processing, since most post grinding processes are wet. However, there are successful - mainly ball mill based - dry grinding examples in gold, nickel or iron ore. Experience from some of these dry grinding references are summarized in this paper. In addition, this paper explores two future-orientated questions: What opportunities does HPGR finish grinding offer the mineral industry? What are general conditions and challenges for adopting this technology for mineral applications?"

Jan 1, 2014

By Xueqin Li, Xuewei Lv, Wenchao He, Jie Qiu, Jie Dang

Iron powders are mainly produced by Hoganas process and water atomization process, while both of which have the disadvantages of energy consumption. To obtain iron powders with higher particle sphericity, more uniform particle size distribution and higher proportion of total iron (TFe), a novel method considering of energy conservation was developed in this paper. The hot metal was transformed into granules with air cooling in a rotary disc atomizer, iron powder particles and hot off-gas were collected respectively. It was found that the property of the obtained iron powders was mainly controlled by the flow rate of the hot metal, the diameter of the rotary disc and the rotary speed and the heat of off-gas has a high level of value as well.

Mar 1, 2017

By Xuewei Lv, Yuelin Qin, Guibao Qiu, Chenguang Bai

"Blast furnace slag (BF slag), is the main by-product in the ironmaking process, which contains large amounts of sensible heat. To recover the sensible heat, this paper described the hot experiments which were carried out in a rotary multi-nozzles cup atomizer, where the molten BFS was transformed into granules without water impingement; subsequently, a new method-pyrolysis the printed circuited board (PCB) with the hot BFS particle, was proposed for recovering the sensible heat in this study. The gaseous products were analyzed by gas analyzer. The residual of the PCB was analyzed by FT-IR and XRD respectively, and the obtained slag particles were analyzed by XRD.The results showed that it is a feasible process of pyrolyzing PCB powder with the hot BFS particle. The sensible heat of hot BF slag could be converted to chemical heat and a large amount of combustible gas could also be generated during the process.IntroductionDue to the rising of the product cost of blast furnace iron (BFI) and the increasing public awareness of environmental problems, the steel industries have to focus on the energy saving and emission reduction. Blast furnace slag (BF slag) is a byproduct from blast furnace exhaust temperature of 1450°C or so, is a high-quality waste heat resources. In China, the steel industry produces approximately 220Mt ofBFS per year, and the enthalpy of those slags is approximately equivalent to 13.3% of the whole energy consumption in the ironmaking process[!]. It can be seen, recycling waste heat is an important way of energy saving for iron and steel enterprises. The molten slag was treated by conventional water quenching method without any recovery of heat in spite of its huge potential. Also, the water quenching process consumes a plenty of water, pollutes the air and water[2]. Additionally, the extra energy is necessary for the drying process of slag to produce cement. As a kind of secondhand resource which can be reused, the BF slag contains a large amount of sensible heat. To recover the sensible heat of BF slag, three key problems should be considered, which refer to ( 1) the dry granulation of BFS without consuming water, (2) how to recover the heat of slag particles efficiently, (3) how to use the slag particles after heat recovery."

Jan 1, 2012

By A. Sobering, G. N. Carlson

"This paper describes the conversion of the grinding section of the W a bush Mines pelletizing plant from conventional wet, open-circuit trunnion overflow ball milling, with filtering, and bentonite mixing on a common conveyor belt, to dry, open-circuit, grate discharge grinding, with pug mill mixing of bentonite and water at individual mills.The test work and data on operating economies to justify the cost of conversion are given. It is too early, at the time of writing, to have complete operating confirmation, but data are available. A brief description of the original plant is included."

Jan 1, 1971

By Craig M. Sams

Dry grinding circuits and factors influencing the selection of the most appropriate grinding system for a given ore selection are discussed. Comparisons of the drying, grindability, installed costs and operating costs are presented for several grinding systems.

Jan 1, 1994

By G. Keizer

Cortez Gold Mine (C.G.M.) is located in Lander County, Nevada, approximately 80 miles southwest of Elko, Nevada. It is accessed via Nevada State Highway 306 south from Interstate 80. This operation is a joint venture between Placer Dome U. S. Inc. (60% operator) and Kennecott Corporation (40%). The claims which supply oxide and refractory ore feed to the Cortez milling facility are located in both Lander and Eureka Counties. These include the Cortez and Horse Canyon deposits all operated by C.G.M. Joint Venture. Other deposits outside the C.G.M. claim area include; Fire Creek, Buckhorn, Gold Bar and Tonkin Springs. These deposits all occur along the Battle Mountain/Eureka Trend.

Jan 1, 1993

By Garry Keizer

The Cortez gold mine is located in Lander County, NR, about 130 km (80 miles) southwest of Elko. Cortez Gold Mines (CGM) is a joint venture between Placer Dome US Inc. (60% operator) and Kennecott Corp. (40%). The claims that supply oxide and refractory ore feed to the Cortez milling facility are located in both Lander and Eureka counties. These include the Cortez and Horse Canyon deposits, all operated by the joint venture. Other deposits outside the CGM claim area include Fire Creek, Buckhorn, Gold Bar and Tonkin Springs. These deposits all occur along the Battle Mountain-Eureka Trend. History Mining in the Cortez district began in 1862 with the discovery of high-grade silver ores. Grades in the hundreds of ounces per ton occurred in an area 7 km (4.5 miles) southeast of the current CGM mill site. Underground mining through the Garrison and Arctic tunnels provided the bulk of the ore production between 1864 and 1895. To a lesser extent, the Mill Canyon area also supplied ore until 1930.

Jan 1, 1993

By R. Weinstein, R. Snoby

There are many advantages to upgrading coal with dry jigging technology. The most obvious is the lack of process water, which eliminates the need for fines dewatering and slurry confinement. Dry jigging eliminates the clean coal moisture penalty associated with wet processing. Particulate emissions are virtually nonexistent due to inclusions of fabric dust collectors on all modern dry jig plants. Due to the environmentally kind nature of dry jig plants, installation permits are often measured in days, not months. Coupled with all these advantages there has been a fundamental advance in dry jigging efficiency. All of these advantages have renewed the coal industry’s interest in dry jigging. But, air jigging isn’t right for every application. There are limitations due to particle size, particle shape, moisture, and near gravity content. This paper explores the evolution of dry jigging; reviews parameters important for determining the suitability of dry jigging; compares historical performance data as measured by imperfection, against results from modern dry jigging technology; and presents actual data from modern dry jig installations.

Jan 1, 2006

By R. Snoby

Since its introduction in 2002, the modern air jig has processed a wide array of coals throughout the world. This paper explores the reasons and justifications for the installations and provides case history performance data. Specifically highlighted are air jig plants processing metallurgical coal in Colombia, bituminous coal in the United States and India and lignite in the United States and Spain. Each installation has unique reasons to justify an air jig facility. It is important to note that not all of the justifications were based on the ?most cost effective yield?, normally a mantra for coal preparation plant designers and owners. Dry jigging of coal has long been a proven technique for upgrading coal, the modern air jig, with its improved efficiency and operating systems simply extended the range of applications. In some cases, it even allows market quality coal to be produced when no other option is possible.

Jan 1, 2009

"Wet low intensity magnetic separation has been used for the recovery of magnetite for decades. As high-grade reserves continue to decline, low grade magnetite ores are being targeted for iron production. Low grade magnetite mineralisation is typically fine grained and requires fine to ultrafine grinding (P80 40 - 30 µm) to liberate it from, predominantly, silica/silicate gangue matrices. Grinding to such particle sizes requires high power consumption and produces excessive fines which impact negatively on wet magnetic separation and tailings dewatering. In addition, the dearth of fresh water for mineral processing in arid areas impacts negatively on the economic viability of low grade magnetite projects. These challenges have motivated innovation in dry magnetic separation technologies for the beneficiation of magnetite that can be economically applied on a large-scale. Such technology has been developed in the Cyclomag Planar magnetic separator (PMS) invented by South Australia-based Christopher Kelsey of IMPTEC P/L. The significant gangue mineralisation associated with magnetite ores in South Australia is quartz. In this study, the performance of the Cyclomag PMS on the recovery of magnetite mineral from magnetite-quartz blends was investigated. Magnetite-quartz blend were subjected to the PMS at varying control parameters - magnet discs rotation speed, inlet airflow and feeder speed. The study showed a successful dry separation of magnetic mineral from non-magnetics using the Cyclomag PMS. The PMS has potential to effectively recover magnetite mineral."

Jan 1, 2018

By A. F. Bridge

IN order to show the need for gas reserves, their control, and conservation, in California, it is necessary to describe briefly the local conditions under which gas is produced and marketed, to point out the lack of coordination between supply and demand, and to relate the history of efforts to prevent wastage. There are now 24 fields in California producing a surplus of gas over field fuel requirements. They are usually grouped geographically into three divisions, as follows: (I) Los Angeles Basin (Los Angeles and 0 r a n g e Counties), thirteen fields, all casing-head gas. Total daily gas available for sale 125,000, 000 ?cu.ft. (2) Coastal (Ventura and Santa Barbara Counties). Seven casine-head and one dry gas field. total-avail- able daily, 165,000,000 cu.ft. (3) San Joaquin Valley (Kern, Kings, Fresno, and San Joaquin Counties). Four casing-head fields, five dry gas fields, and two producing casing- head and dry gas from different zones. Total available daily pro- ducticon, 475,000,000 cu.ft. Total all fields, 765,000,000 cu.ft. daily.

Jan 1, 1936

By M. Le Roux, Q. P. Campbell, N. Hughes

Water plays a significant role in minerals processing; this is especially true in coal preparation where water-based beneficiation is widely accepted and consistently delivering sharp separation efficiencies and high product yields. Although wet processing is favoured, the substantial process water requirement may prove this impractical and unsustainable in some parts of the world. Many coal-rich regions (including South Africa) have experienced severe water shortages. Coupled with the effects of drought, some countries experience freezing winters from which problems related to frozen process water and machinery may arise. Hence coal preparation practices will soon have to adapt, irrespective of the technical and economic feasibility offered by the currently employed water-based methods. As a result, extensive research into the development of dry methods for effectively beneficiating coal has progressed. This review paper intends to provide a collection of the relevant information pertaining to dry coal processing globally, and aid in understanding the applicability, performance, success or failure thereof. The methods available for dry materials preparation, with special regard to those applicable for coal beneficiation, are detailed in terms of principle, applicability, limitations and performance. Dry coal beneficiation has potential to aid the current wet-based methods with some considerations to possible limitations set forth by coal geology, application, product specification, particle size distribution, moisture, efficiency, capacity and cost. These methods may be established in future, especially in the arctic, arid and under-developed regions through new plant installations, expansions and small mines processing. Keywords: Dry coal processing, preparation, cleaning, beneficiation

Jan 1, 2020

By W Skinner, C G. Kelsey, J R. Kelly

The iron ore industry has reached the end of an unprecedented period of expansion triggered by China’s demand for iron ore. Lower ore prices have led producers to focus on optimising mining operations while extracting the maximum tonnage from the infrastructure presently in place or from projects already underway. A rising global surplus is expected to further force ore prices down and lead to output curtailments, which in turn will help to restore market balance. However, investment in the development of new resources and the development of new infrastructure will inevitably become necessary. Making the right decisions in relation to future processing infrastructure in a climate of uncertain demand and price volatility will not be as straightforward as in the past, where expanding the scale of a proposed operation has been the answer to ensuring economic viability. Overall cost and environmental pressures particularly in relation to wet processing will dominate the decision-making process. IMP Technologies (IMPTEC) has anticipated the need for a dry low cost processing alternative, which can open the way for the development of lower grade magnetite deposits and ensure the sustainability of processing in Australia. The lower grade magnetite deposits are generally fine grained and require grinding to p80 of 30 to 40 microns. Historically, the cost of grinding to these sizes has been and remains a key factor determining the economic viability of a magnetite processing operation. The IMPTEC Super-fine Crusher and Cyclomag Separator are the key components of a proposed radically simplified dry processing alternative, which addresses both cost and environmental issues. This paper reports on the results of pilot super-fine crushing and cyclomag separation test work, focused on supporting the feasibility of the proposed dry processing route for the production of high-grade pellet plant feed from fine grained low-grade magnetic ores.CITATION:Kelsey, C G, Kelly, J R and Skinner, W, 2017. Dry processing of magnetic iron ores – addressing cost and environmental issues, in Proceedings Iron Ore 2017, pp 215–220 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By A. H. Sharbaugh

It is believed that considerable economic benefit would arise if run of mine (ROM) coal from the underground mines in the Winifrede seam could he enriched before shipment to the preparation plant by partial removal of the shale. Shale could comprise up to 50% of the ROM product. Complete mine-mouth separation is not necessary, but any process must be dry and have high Btu recovery. We have conducted a preliminary analysis of coal/shale mixtures from the Winifrede seam and we find that it is quite possible that a 50-50 ROM mixture of coal and shale could be converted to a 60-40 coal-shale mixture by inspection of individual lumps coming from the mine. The device would consist of a feeder/siever section to deliver the ROM coal > 5 cm (2 in) to an inspection station via a conveyor belt. This inspection station decides if a piece is coal or shale, and if it is shale, activates an air jet to blow shale off of the belt. We have evaluated a dielectric loss technique for the inspection device. The potential advantages of the dielectric loss method are high throughput, low capital cost, and no special handling or licenses would be required. Such a single lump inspection technique is made possible because of advances in high speed electronics and servo systems. This paper provides a summary of our analyses on the Winifrede coal sample, a description of a proposed apparatus to separate coal from shale, some of the experiments needed to demonstrate our ideas.

Jan 1, 1984