Search Documents

By Antoni Kalukiewicz

From 1997 through 2000, a team of Polish experts headed by the author studied the prospects of mining newly discovered emerald deposits in Afghanistan. This article describes the scheme for mechanization of the mining operations, along with improvements made to the ventilation facilities and lighting. The required equipment was flown to Afghanistan and the Afghan miners were trained in machine operation and maintenance.

Jan 1, 2005

By S M. Aminossadati, C M. Stewart, M S. Kizil

Mine ventilation models are now an accepted component of most mine management systems. However, modern ventilation models also represent a highly structured spatial data source, defining underground pathways and connections across a mine. This creates opportunities to extend the use of network models beyond ventilation design, by using critical path algorithms to find pathways such as minimum distance or minimum time.This paper explores the use of ventilation network models to automatically analyse and calculate potential emergency escape routes. A variation of Dijkstra’s algorithm is used to predict complex pathways between any two points across a model, representing an escape route from an emergency area (such as a fire) to a safe location (such as the surface or a refuge station). Weighting can be assigned to paths to represent potential travel speed, obstructions or preferred routes. Finally, emergency considerations such as smoke or gas in some parts of the mine can then be incorporated into the pathways to force the algorithm to avoid dangerous routes and specify safer pathways. Ventsim is used to visually show example results.Emergency egress pathway prediction using ventilation network models can provide an efficient way to quickly predict the quickest or most efficient escape routes for emergencies or planning purposes.CITATION:Stewart, C M, Aminossadati, S M and Kizil, M S, 2017. Emergency egress pathway prediction using ventilation models, in Proceedings Australian Mine Vent Conference 2017, pp 57–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Eric Schraml

Wardrop Engineering and the Placer Dome?s Campbell Mine Design Team utilized leading edge directional raise boring techniques and an innovative, remote controlled application of steel fibre reinforced shotcrete ground support to achieve improved mine ventilation and a superior, safety focused secondary emergency egress. While more standardized methods may have provided a sufficient solution to either the requirement for a ventilation raise or for a traditional escape ladder way, innovative methodology ensured both objectives were met with a single, enhanced solution. Placer Dome committed to provide a solution that minimized energy consumption, optimized air delivery and facilitated an escape way focused on minimizing the negative physiological aspects associated with mine evacuation. The project was successful in providing a new airway, returning 47 m3/s (100,000 cfm) from the 39 Level to 30 Level, minimizing risk to the raise equipping crew and providing a fully equipped escape hoist. The resulting secure escape environment provided an efficient means of evacuating personnel working at depth without necessitating a potentially dangerous exhausting climb to surface. The project has substantiated, that optimized safety focused design can be achieved without jeopardizing project economics.

May 1, 2002

By D. Bristow, D. Baker, K. Awuah-Offei, A. ur Rehman

While a body of work exists on intelligent systems for guiding occupants out of buildings during an emergency, the problem of guiding miners out of a mine during an underground emergency has not been explored. Underground evacuation fundamentally differs from building evacuation because of differences in the regulatory regime and uncertainty regarding the number of occupants. The potential for implementing an intelligent miner guidance system is buttressed by the fact that miner tracking systems, along with communication and sensor networks, already exist in underground mines. This work presents a method based on a local positioning system, in the form of a network of “nodes” at major “intersections,” which can then be used to guide miners to safety. We have developed a path-planning algorithm, based on Dijkstra’s algorithm and the local positioning system that can provide miners with the optimal escape path in an emergency. The algorithm is validated with scenarios at the Missouri University of Science & Technology Experimental Mine demonstrating the potential to include smart technology in mine emergency management and response planning. INTRODUCTION Underground mines are hazardous environments with a higher than usual risk of safety emergencies where miners have to evacuate the mine to save their lives. Mines have always trained miners to evacuate or shelter-in-place in minimum time. Jalali and Norrozi (2009) opined that the three major components that help miners in case of emergency are pre-planned optimal escape routes, decreasing delays, and improving the education of miners. In fact, Goodman and Kissel (1990) suggested that fatalities arising from mine accidents could be reduced by 50% just by decreasing delays in finding the pathways in case of emergency. The proposed work can assist miners in finding escapeways quickly in case of emergency. It is very important to have a pre-planned evacuation strategy that is clearly communicated to miners to ensure the safety of all (Conti, Chasko & Wiehagen, 2005).

Jan 1, 2019

By Tai Luu, Michael McNicholas, James C. McIntyre

The Jersey City Municipal Utilities Authority (JCMUA), discovered that an existing sewer pipe had collapsed under the New Jersey Transit Conrail Railroad between Pine Street and Ash Street in Jersey City New Jersey. Immediate action was taken to abandon the pipe in place and install a new sanitary sewer. The borings showed 10-20 ft (3.04 m.- 6.09 m) of competent fill overlaying approximately 8 ft. (2.44 m.) of compressible peat and organics. Groundwater was at 8 ft (2.44 m) below ground level. The poor condition of the soils at subgrade could not withstand the extreme weight of the jacking machine or the thrust force required to push the casing from the launching pit to receiving pit. The support of excavation (SOE) would therefore not only need to retain the soil to allow the jacking equipment to reach subgrade at 14 ft (4.27m) below working grade, but also the back wall of the SOE would need to be sufficiently robust to function as the reaction block for jacking operations. The alignment and allowable tolerance for the jacked casing was minimal, therefore the performance of the SOE was extremely critical to the success of jacking operations. This paper will discuss in detail the design concepts that were developed and implemented by the team to overcome these obstacles. HISTORY The discovery of a collapsed section of an existing sanitary sewer led the Jersey City Municipal Utilities Authority to act on an emergency contract. The project design team was tasked with developing an abandonment plan for the broken pipe and installation of the new pipe through challenging geology. The new 180 ft.(54.96 m) long, 54-in. (1.37 m) . diameter sewer pipe was designed to be contained within a 72-in. (1.83 m) protective steel casing. The installation of the new sewer pipe would require a detailed understanding of the geology. The geotechnical subcontractor assembled a subsurface investigation report on November 2nd, 2017. It was quickly realized that the only way to replace the pipe was with a jacked pipe system since the large grade change and the Conrail Right of Way created no other alternative. Delaying or closing the railway was absolutely not an option as that particular railway served as the main heavy-haul route to and from Jersey City. It became apparent that a major obstacle to pipe jacking was the challenging geology present across and beneath the proposed sanitary sewer. The following challenges faced the design team prior to the installation of the replacement pipe:

Jan 1, 2019

By BERNARD PLANNER

PRODUCTION COSTS, profits, and quality are the primary factors in the peacetime production of iron and steel. In a war emergency, as high production rates and as complete utilization of readily available raw materials as possible, consistent with securing passable quality, become the most important factors. In this connection a discussion of some of the recent developments in the German iron and steel industry, where the problem of scarcity has naturally always been more acute than in the U.S.A., maybe of interest. To get more pig iron out of the existing blast furnaces it was necessary to obtain the maximum efficiency from the iron-bearing raw materials. This was achieved by eliminating all "excess baggage," chiefly by beneficiating the ore. The preparatory work for this was done by various methods which are effective when the ore either is too poor or contains too many impurities or too much gangue. Some of the beneficiation methods are well known, some are combinations of wet-mechanical, magnetic, roasting, sintering, and other treatments.

Jan 1, 1942

By J. E. Carrasco, J. D. Stinnette, R. A. Alvarez

"Chuquicamata Underground Mine is one of the main projects for the Chilean government copper company (CODELCO). Underground mine project has been under construction since 2013 and presents a solution for the lower production levels of the open pit and prolongs the life of the mine for the next 40 years. Currently, around 2000 workers operate in the mine daily. Dozens of trucks and heavy machines drives through all main routes and access in the mine. As a mine under construction not all the infrastructure necessary to operate safely in the mine has been completed. Risk of a truck or fixed facility fire is always a challenge to keep under control. One important part of fire simulation relays on what we can do prevent a fire and what can be done with the existing infrastructure to control a declared fire and start evacuation plans. This study has been made as a feasible emergency plan to implement, in this case, of a mine under construction, were limited resources are available. Several fire scenarios have been made to support all the emergency plan strategy and a detailed step by step procedure indicates what the elements of a fire emergency plan and risk analysis are.INTRODUCTIONThe main objective of this study is to describe the importance of fire risk analyses (FRAs) and different methods to be used before commencing fire simulation and methodology steps utilized for a fire emergency plan strategy (EPS) at the Chuquicamata underground mine. It also describes how to classify zones which are going to be affected by fumes and gases propagation derived from the exact location of a fire event. Fire simulation study is helpful to determine the impact on a ventilation system with the main purpose of providing relevant information to complement emergency plans and stablished control techniques in ventilation design and its operation. Most fire simulation studies only concentrates in simulation techniques on itself. But what is the next following step in developing an emergency plan? How can we evaluate, classify and treat risky areas? This study is focused mainly in the phases before and after a fire simulation process. Phases corresponds to a good FRA and how output data can be used for an EPS."

Jan 1, 2019

By David Jurich, Joseph N. McDivitt

INTRODUCTION South Coast Water District (SCWD) operates the Beach Interceptor Sewer Tunnel(BIST) in South Laguna, Orange County, California between Monarch Beach and Aliso Beach (Figure 1). The 10,200-foot long BIST houses a 24-inch gravity Techite sewer pipeline critical to the SCWD Sanitary Sewer Collection System. The original tunnel and sewer pipeline were constructed in 1954 and the sewer line was replaced in 1974.Periodic inspections by sewer pipeline maintenance crews documented deterioration of specific intervals of the tunnel. Rotting timber supports and rock falls in the tunnel as a result of the deterioration were endangering the sewer pipeline and a 731-foot section of tunnel located at Thousand Steps Beach was determined to be in immediate need of repairs. SCWD and consultants Hatch Mott MacDonald (HMM) and Tetra Tec prepared a Work Plan for emergency tunnel stabilization and pipe protection measures that was implemented in January 2007. Normal access to the beach and the section of tunnel requiring repairs was limited to public stairs referred to as Thousand Steps and, therefore, all materials and equipment needed for the work were transported to the beach by ocean-going landing craft. Additionally, the emergency repairs had to be completed without taking the pipeline out of service. Numerous environmental, logistical and operational requirements had to be overcome to complete the challenging emergency repairs. GEOLOGICAL SETTING The Laguna Beach area is located in the Peninsular Ranges of Southern California. The project area is located on the southwest flank of Niguel Hill along marine wave-cut cliffs and slopes. The tunnel was excavated in the San Onofre Formation, a marine deposit, characterized by abrupt lateral and vertical changes in lithologies that vary from boulder to cobble and gravel size breccias to medium coarse sandstones with gravel, sandy claystone and siltstone. The interval of the tunnel that required repairs is located within the San Onofre breccia, a moderately-to-well cemented, poorly bedded to massive unit with angular to subangular boulder and cobble sized clasts of schist. The sandy silt matrix of the breccia is composed of quartz, feldspar and schist grains (Figure 2). GENERAL TUNNEL DESCRIPTION The approximately 6-feet high by 6-feet wide 10,200-foot-long BIST was hand mined in 1954 at the base of the coastal cliffs. Primary access is through twenty-one access adits from public and private beaches. The tunnel is located in an easement that extends beneath private property with residential structures situated 50 to 80 feet above and horizontally in close proximity to the tunnel alignment. Most of the tunnel is horse-shoe shaped and unsupported, but approximately 3,000 feet is supported by timber

Jan 1, 2007

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

C. 7 Emergency Rescue Hoists There is a need, especially in mine development areas, for portable, on-call, man-rated equipment capable of lifting men through several hundred feet. Wire rope climbing equipment as shown in Figure 37 appears particularly suited to this need. It is portable, weighing approximately 100 lbs. , is currently man-rated for numerous above ground applications and can be electric or air powered. Commercial units currently have a lifting capacity of 1000 lbs. , and can be fitted with bosun' s chairs. Lifting speeds are in the 20-30 FPM range and the equipment is not depth limited. In a situation where miners are unable to climb to the top of a shaft this equipment could rapidly be anchored to the top of the shaft and lowered to them by hand. Since the self contained unit is controlled by the person travelling in the shaft he would be able to negotiate shaft obstruction himself. This would not be possible with other forms of easily deployed free-hanging equipment. Typical manufacturers of this type of equipment are Ohio Hoist Mfg, Co, 321 South Beaver St. Lisbon, Ohio 44432 216-424-7283 Sky Climber Inc. 17311 South Main St. Gardena, California 90248 213-321 -6414

Jan 1, 1976

By Rick Deschamps

"Fountain Slide is located approximately 10 mi (16 km) northeast of Lillooet, British Columbia, Canada, within the Coastal Mountain Range, and has been locally active since the 1970s. The project site is located near the base of the relic Tunnel Mountain landslide. The progressive movements have posed a significant challenge to British Columbia (BC) 99, the main north-south highway in the region. The slide began affecting the British Columbia Railway Company (BCR) tracks in the 1990s. In 2004, the Canadian National Railway Company (CN) acquired BCR and, during the next 11 years, undertook measures to stabilize the rail bed. Some of the measures undertaken include numerous track realignments, a shotcrete and soil nail wall, an anchored soldier pile-and-lagging wall, and adding a row of anchors to the wall. For many years, the measures had proved successful until mid-2014 when it was observed that the slide retrogressed uphill of the tracks. Since that time, the slide movements typically ranged between 5/32 and 0.4 in (4 and 10 mm) per day, leading to extreme distortion of the earth retention system and the need for frequent track realignment.In the spring of 2016, CN issued a request for proposals (RFP) for a designbuild solution with the expectations of: (1) a safety factor greater than 1.2, (2) considering only the currently identified retrogressive blocks that extend to about 200 ft (61 m) above the track; and (3) minimizing activities outside the current easement. It was also communicated that there was a possibility that a portion of the line may have to be abandoned if the proposed remediation was cost prohibitive.The fact that the existing slide was a small fraction of the relic slide was intimidating. The relic slide extended for approximately 1.0 mi (1.6 km) above the uppermost retrogressive block that was now affecting the rail line. Other areas of concern included:"

Jan 1, 2017

By Raymond E. Connell

From a macro business process perspective, if what we do in the Mining Industry is find material, dig it out of the ground, convert it to a product and sell it, we are in what might be considered a "simple business". If it is so simple, where does information technology fit? How does it affect our industry? Is it a strategic tool for our industry? What approach should we be employing to ensure we are utilizing information technology effectively? How is information technology integrated or tied together with other areas in the organization such as process control? What kind of people and skill sets are required to support the whole area of information technology? What effect does information technology and automation have on streamlining and rethinking the way we do business in the 90's. This paper covers how these areas have been addressed within the Noranda Group of Companies. It reviews how information technology has evolved, the approach, and what effect it has had on a diversified natural resources company in the mining and metals, forest products, and oil and gas industries.

Jan 1, 1993

By John N. Murphy, Edward F. Fries

The availability of fast, low-cost computer hardware and advanced software is opening new opportunities for minerals extraction and processing. Programmable Logic Controllers (PLC's) are currently used extensively in the minerals industries; this paper looks beyond PLC's and that vintage of “computer control”--it looks toward what the authors see as new in the next five years. Topics covered include expert systems, neural networks, intelligent signal processing, and hierarchical controllers as applied to mining and mineral processing operations.

Jan 1, 1993

By G. Bierie

The conveying of bulk materials is prone to problems. These problems can reduce the capacity and efficiency of the plant, and even threaten the health and safety of the workforce. This presentation will look at new conveyor technologies systems, and how, used separately or in combination, they can improve material handling.

Jan 1, 2007

By Ulrich Maidl, Jamal Rostami, Ulf Gwildis

Tunnel Boring Machines (TBM) have more or less become the preferred method of tunneling in various ground conditions and Programmable Logic Controllers (PLC) or microprocessors are standard features on TBMs to monitor and record various sensory systems on the machine providing the possibility for machine automation and control. The data collected from these sensory systems and channeled through PLC is stored for real-time analysis or use by the operators. Based on typical construction specifications, part of the information collected in the process is shared with the project management team representing the owner. Machine data automatically acquired during TBM advance is typically processed by specialized software to offer the project team data visualization and evaluation options. Interfacing with Geographic Information System (GIS), Computer-Aided Design (CAD), 3-D geologic model, instrumentation data bases, and Document Management Systems (DMS) allows for developing Building Information Models (BIM) of the tunnel’s as-built condition. Application of Artificial Intelligence (AI) processes such as Machine Learning (ML) have already been used for analysis of data, including performance prediction of hard rock TBMs, and exhibited the potential of big data analytics in improving the productivity of the operations. This paper outlines anticipated disruptive technological advances with implications on geotechnical exploration, TBM operation, face condition tracking, subsurface risk allocation, and claims management in the future.

Jun 13, 2021

By J Ramezani, K Faure, N Mortimer

Western New Zealand can be regarded as a rifted continuation of eastern Australia. Detailed studies of units previously considered to have trans-Tasman correlations are being undertaken within the FRST Programme Mineral Wealth of NZ and its EEZ to test specific connections, and thus add to the exploration framework of NZ. Correlation of two major episodes of granitic magmatism are currently being investigated. These represent the oldest (mid Paleozoic) and youngest (Early Cretaceous) magmatic events that conjoined Australia and New Zealand are believed to have in common.

Jan 1, 2007

By David Maust, Rob Albinger, Mike Walling, Michael Rispin

The safeguarding of health and life is the number one priority for underground infrastructure projects. While culture and approach are critically important, the industry has also seen the development of innovative tools and technologies that assist in making the underground environment and working places more safe and secure, both on an everyday basis and in the event of an unexpected occurrence.

Dec 1, 2022

By R. Dippenaar

The emergence of new steel grades is largely driven by the need to produce high quality steel at a competitive price. The principal aims are to attain ultra-high purity, (especially low interstitial elements) and ultra-cleanliness (by the control of the inclusion content and size). Whereas the steel used to build the Titanic contained 650 ppm sulphur, resulting in MnS stringer-inclusions 25 mm in length, modern quality requirements for arctic pipelines would only allow 10 ppm of sulphur and inclusions in ball-bearing steels must be smaller than 5µm. Most developments are aimed at hot-metal treatment before refining and ladle treatment after decarburisation. Because ferroalloys are added during or after the refining step, it is the secondary (ladle) refining production technologies that are of specific interest to the ferroalloy producer. Through ladle treatment, hydrogen and nitrogen contents are reduced, ultra-low levels of solute impurities are attained and the shapes as well as the composition of inclusions are modified. Steelmakers are concerned about the cost effectiveness of the use of ferroalloys such as consistent product analysis and delivery, improved financing arrangements and technical support. Minimal variation in product sizing is vital because it impacts on handling problems and because particle size determines the rate of particle dissolution. The required ferroalloy product quality depends on the specific use but in general sulphur, phosphorous and nitrogen contents are of concern. Apart from the presence of trace and impurity elements, ferroalloys also contain inclusions. For example, ferromanganese may contain MnO-MnS-SiO2 inclusions while high-carbon ferro-chrome may contain different kinds of Cr-Mn-spinels. The presence of these impurities and inclusions has a significant impact on steel production techniques and cost and hence, on the selection and use of ferroalloys. The interrelationship between ferroalloy quality and steel production technology is plant and product specific and hence, effective communication between ferroalloy suppliers and steel producers is essential.

Jan 1, 2004

By E. L. McHugh, J. M. Girard

This paper discusses the results of two recent case studies in which high-tech prototype instruments were used. The first case study describes the results of a ground-based hyperspectral imaging tool used to map the geology of an open-pit mine highwall. The second case study outlines the use of interferometric synthetic aperture radar and how this type of radar can be used in a variety of geotechnical situations. These case studies are part of an on-going research project at the National Institute for Occupational Safety and Health’s (NIOSH) Spokane Research Laboratory. The project objective is to implement engineering controls and design methods in order to reduce the number of injuries and fatalities associated with slope failures at mining operations. Project personnel are hopeful that these new developments in technology will lead to better geotechnical monitoring and design in slope stability and other important areas of rock mechanics.

By D. E. Pollock, T. W. Beck, J. A. Organiscak

This work presents the findings from a number of NIOSH studies evaluating the impacts of emerging technologies that may reduce dust exposures for continuous mining and roof bolting personnel. These technologies include use of a wet head cutting drum on a continuous mining machine that places water sprays on the cutting drum instead of placing them on a manifold outby the drum. Evaluations at two separate operations showed that the use of the wet head sprays reduced dust levels at the miner operator in the return air, although these reductions were quite variable. NIOSH also assessed the effectiveness of a canopy air curtain for protecting roof bolting personnel. The data showed that dust levels were lower beneath the air curtain than outside the air curtain. This study also suggested several future modifications to the air curtain to in-crease its effectiveness. Finally, NIOSH evaluated mist drilling technology for its effectiveness in controlling respirable dust exposures of bolting personnel. A recent study showed that higher dust levels existed around a machine using the mist system compared to a machine using a conventional vacuum system for dust control. Unfortunately, the true impact of mist drilling was confounded by this machine operating downwind of the continuous miner for much of the study.

By Prasad S, Chatterjee S. S, Singh B. N

The chief source of metallic iron for steelmaking in India, even today, as it is in most part of the world, is through blast furnace (BF) route. This will continue to be so in the foreseeable future as the technology is most efficient, both process and economy-wise. However, as the world is moving into the next millennium, a critical look is being given to the process primarily because of its non-ecofriendliness (as a result of extensive use of metallurgical coal/coke requiring elaborate pollution control facilities) and huge investment involved for supporting facilities like extensive raw material preparation and handling, agglomeration, adoption of sophisticated instrumentation and control system, etc.

Jan 1, 1999