Search Documents

By N. Kumar Kittusamy

ALTHOUGH MANYSTUDIES HAVE SHOWN an association between operating heavy construction equipment and symptoms of musculoskeletal disorders (MSDs), little research has been performed that systematically characterizes the exposure of operating engineers to ergonomic hazards. This study evaluated: 1) vibration at the seat/operator interface;2) transmissibility of vibration in the Z-axis; 3) psychophysical ratings of vibration level and vibration discomfort; and 4) postural requirements of the job. Results indicate that the digging operation had higher levels of total weighted acceleration than high- or low-idling conditions. Transmissibility data showed that the seat amplified vibration, particularly in the lower frequencies. Seats demonstrated that they may not be sufficient in protecting operators from long-term effects of vibration exposure. High positive correlation was found among subjective ratings (vibration discomfort and vibration level), but moderate positive correlation was found between subjective ratings and quantitative vibration levels. Postural evaluations revealed that the operators were required to assume awkward postures of the neck, shoulder and trunk while performing their jobs. Work-related injuries and illnesses pose a continuing threat to the health and well-being of American workers. The construction industry has been historically recognized as having higher rates of fatality, injury and illness than other industries (McVittie285+; BLS). In 1994, an estimated 218,800 lost-work-day injuries were reported in the construction industry (BLS). Construction also had the second-highest incidence rate for sprains and strains. Although the industry has made progress since then, injuries and illnesses, including MSDs, continue to because for concern.

By M. Z. Emad, M. U. Khan, A. ur Rehman

Stemming plugs are used as an accessory in drilling and blasting industry. They supplement conventional stemming material (i.e. drill cutting) with retention of gases in the drill hole that result in better fragmentation of rock and improved explosive utilization. Better fragmentation and explosive utilization along with economic benefits enhance efficacy of the project. Incorporation of stemming plugs in drilling and blasting industry is in exercise for about thirty years. The efficiency of stemming plugs is a key factor in their rising induction in mining industry. Different studies have been conducted on the economic viability of these plugs. The focus of this paper is the selection of stemming plugs for a bench blasting operation and the examination of blasting operation efficiency based on ergonomics and human factors. Three types of stemming plugs were evaluated during multiple blasts at a limestone quarry. Their performance was evaluated using split desktop software. Based on the human factors plastic molded stemming plug (stemming plug-1) was found to be the best among all selected plugs. INTRODUCTION Surface mines and quarrying operations heavily depend on bench blasting to achieve high volumetric targets and production demands. Use of explosives is the most economic method adopted for rock breakage and movement. Extensive research had been performed to enhance explosives energy utilization. This include changing the drilling pattern, application of air decks, stemming plugs, and use of other supportive devices. Optimization of explosive energy has been a major concern in those mines that rely on drilling and blasting operation to carry out main production. Due to continually increasing cost, efficient mining demands, and associated hazards of using explosives, it is necessary to utilize explosives at their best. Efficiency of a blasting operation is generally evaluated by the fragmentation size. From post blast conditions at blasting site to efficiency of processing plant, anything can be affected due to improper blast resulting in bad fragmentation. Better fragmentation is necessity for better operation of the system along with consideration of the safety of operation, environmental issues and related costs. For developing a blast design, an engineer should always attempt to minimize the cost of operation without compromising with acceptable technical and safety necessities [1]. Blast performance is dependent on many different factors associated with the process. These factors have been gauged as blast geometry, explosive specification, and rock mass properties [2]. Similarly, in 2013 Mohammad et al. concluded that fragmentation dynamics depends on blast hole diameter, primer, spacing, stemming, burden, and delay timing for blasting operation [1]. At the work site where this study was performed, blast holes were filled by drill cuttings and muds to help in confining gases. In a blast hole, gas confinement helps in better rock fragmentation along with reduced flyrocks. This practice is most common in many countries including Pakistan. Due to lack of homogenized particle size, the effectiveness of confinement is variable and majorly based on the size of stemming. Extremely small sized drill cuttings often result in hole blow out along with flyrocks from the collar. This improper blast energy will result in poor blast, bad impacts on environment, and reduced operational efficiency. In addition to the stemming material, the length of stemming is also a prime consideration. The decrease in stemming length will increase the quantity of explosive in the blast hole and an increase in stemming material generally improves stemming performance.

Jan 1, 2019

By X B. Sun

Mining work is a high-risk operatation under a special environment. It is affected by space, lighting, noise, vibration, dust, air pollution, etc as well as coal seam conditions, complicated geology construction, combustion of coal, gas, coal dust, etc. Factors which affects safety production are numerous, eg natural conditions, technical equipment level, producersÆ and managersÆ qualities. It is a complex system engineering to ensure mining safety and high efficiency. Among the ideology, methods and measures of safety management are the most important factors besides safety technology. Mine productive environment is a main problem that affects minerÆs work as far as safety and health are concerned. Combining ChinaÆs mine productive environment situation and using human ergonomics theory, this paper explores a series of measures and suggestions as to how to reinforce safety management, how to build up the safety management ideology, how to improve the mine production environment, how to decrease coal mine accidents, and how to ensure mining safety and high efficiency.

Jan 1, 2003

By P. C. Schutte

Ergonomics is the scientific discipline concerned with the understanding of interactions among humans and other elements of a system, and the profession that applies theory, principles, data and methods to design in order to optimize human well-being and overall system performance. Despite the fact that the application of ergonomics principles can make a major contribution to the management of significant occupational safety and health risks, ergonomics is currently applied on a limited scale in the South African mining industry. The objective of this paper is to provide a perspective of ergonomics, the main aim being to create a point of departure for the development of strategic objectives to enhance existing health and safety initiatives through the application of sound ergonomics principles. Two of the major consequences of poor ergonomics, namely work-related musculoskeletal disorders and worker fatigue, and possible means of introducing ergonomics into the South African mining industry, are discussed.

Jan 1, 2005

By D. Caruso

The health and financial costs of cumulative injuries are plaguing the mining industry. Industry leaders are concentrating on reducing the risk of injury to their workers through design and redesign of work environments. While ergonomics is not a currently regulated field, many mines are realizing that the only way to tackle their most costly injuries, cumulative injuries, is to make the proactive choice to understand those injuries, their root causes and to make workplace changes to prevent them from occurring. Reduction of these injuries not only improves the health and morale of the workers but increases productivity and profit for the companies. Knowledge and reporting of ergonomic risk factors by employees and ergonomics committees is key to these changes and to the reduction of cumulative injuries. NIOSH is developing strong relationships with industry associations and equipment manufacturers to leverage their communication abilities to transfer knowledge to their customers and make a difference in the health and safety of U.S. miners. The benefits of a formalized approach to reducing these injuries along with examples will be presented.

By A. J. Carlson, G. M. Marincel, M. L. Hovland, J. H. Healy

Research personnel of Erie Mining Co., a pioneer taconite mining firm on the Mesabi Range, have invented a new method to make an effective 325 mesh separation at high tonnage rates over stationary screens. The company regards this development as historically significant in that it represents the first successful method to commercially screen large tonnages of ore at fine sizes. Erie, which is now completing an expansion program at its plant site near Hoyt Lakes, Minn., has incorporated this screening method as part of that expansion. When completed, the concentration plant will produce 10.3 million tons of iron concentrate, all of which will have been efficiently screened at 325 mesh.

Jan 4, 1967

By P Christen

The Ernest Henry Copper gold mine situated in North West Queensland, Australia, is owned and operated by Xstrata Copper. Currently the open pit produces 11 Mtpa of ore. With open pit mining ceasing in mid 2011 development has begun on an underground sublevel cave mine to extend the life of the operation by another 12 years. When completed the open pit will be 530 m deep and 1.5 km in diameter. The orebody dips at approximately 45° and has been outlined a further 450 m below the base of the pit. This provides some challenges for the Ernest Henry underground mine which is designed to initially truck development and production ore from the end of the pit until a hoisting shaft is commissioned in 2013. Production will then increase to 5.0 Mtpa on its way to an ultimate rate of 6.0 Mtpa in 2016.This paper will focus on the capital development and infrastructure requirements for the underground mine. Areas covered include mine accesses, ore handling system, accommodations for the dip of the orebody, primary ventilation design, dewatering systems and selection of an underground workshop over surface only maintenance.Discussions include the complications arising due to the mine being located directly below a large open pit and the combination of first principle cost analysis and risk assessment which has been used to safely optimise the feasibility study designs.

Mar 21, 2011

By X. T. Zeng, X. Z. Ding, W. R. Chen, L. R. Zhao

The effect of deposition defects in metal nitride coatings on erosion behavior is presented. AlCrN, AlTiSiN, TiSiN and TiSiN:MoS2 coatings were fabricated by reactive cathodic arc evaporation and unbalanced magnetron sputtering processes. The microstructure and mechanical properties of the coatings were characterized by X-ray diffraction, scanning electron microscopy and nanoindentation, and the erosion property was assessed by solid particle impingement testing. The erosion characteristics on the coating surface and cross section were analyzed and correlated to the defects, which played an important role by promoting formation of erosion pits.

Jan 1, 2006

By I. M. Gordon

"INTRODUCTIONThe Hollinger tailing disposal plant is situated about 1 1/4 miles south of the mill. The area available for tailing covers 620 acres and is roughly 1 ¼ miles long by ¾ mile wide.Tailing was first deposited on the northeast section of the present site. This section, 1 mile long by ~ mile wide, sloped from northeast to southwest, the slope amounting to 106 feet between the northeast corner and the low land to the south west. The low land was wet and a considerable area was covered with muskeg up to 17 feet deep. It was drained by a creek running across the property in a southwesterly direction. Later, when more ground was needed, the low lying mining claims adjacent to the south and west boundaries were acquired to allow for expansion of the plant. This entailed some extra difficulties and expense that would not have been necessary had the whole of the present site been acquired with the original purchase.At the conclusion of milling, May 7, 1968, the site contains nearly 56 million tons of tailing. The top of the deposit is from 70 to 90 feet above the original low lying ground along the northwest, west and south boundaries."

Jan 1, 1969

By R H. Sibson

The gold province of Otago occupies an area of upwarped basement, the Otago Schist, comprising predominantly quartzofeldspathic and volcanogenic metasediments. This assemblage is the product of collisional tectonic deformation and associated metamorphism, mainly to lower greenschist facies, during the Rangitata Orogeny (200-100 Ma). Historically this region has produced 240 tonnes of gold, 4% (10 t.) of which was from the mining of Cretaceous goldquartz mineralised vein systems. Auriferous vein systems in the Otago Schist are mainly hosted within NW trending normal fault-fracture arrays, however NW trending reverse fault-hosted vein systems also occur. We propose that the Late Cretaceous-mid Tertiary Otago Schist structure represents a regional anticlinorium containing flexural folds of at least two wavelengths. The anticlinorium structure has been quantified by determining variations in angular discordance between schistosity and the Otago Peneplain, a Late Cretaceous-mid Tertiary erosion surface covering most of the Otago district. A structural model for the evolution of the post-collisional anticlinorium requires the cooling surficial zone (carapace) of a retrograding metamorphic belt to behave as an elastic lid. Erosion of topographic load on the carapace drove isostatic uplift, which was greatest in the tectonically thickened core of the orogen. In this way differential uplift produced flexural deformation in the elastic carapace, expressed as a large scale arching of the orogenic belt. Flexure created tangential longitudinal strains in the outer-arc, leading to extension and the formation of mineralised normal faults. These structures are separated by a neutral surface from shortening and associated mineralised reverse faults in the inner-arc. Our structural model predicts that the distribution of auriferous lodes should be localised about zones of maximum flexural curvature, where the tangential longitudinal strains are highest. As a result, NW-SE hinge regions separating schistosity dip domains in the Otago gold province may have new found significance as potential exploration targets.

Jan 1, 1995

By R. S. Shoemaker

Environmental and regulatory authorities are increasingly requiring that precious metals heap leach piles be contoured before they are abandoned so they may present a more "natural" look to the eye. Depending on the ore type, many of these contoured heaps will be subject to substantial erosion by precipitation events, native plants will have difficulty in establishing themselves and slimes be washed onto surrounding areas or into watercourses. This paper presents the argument that the results of contouring heaps are counter to good environmental practice. Calculations which have been made demonstrate that leveling and berming the heap tops as well as berming the edge of each lift or setback will effectively prevent water erosion and promote the growth of native plant species.

Jan 1, 1993

By HENRY FA

HENRY FAY (communication to the Secretary*).-In reply to the discussion of my paper, I wish to take this opportunity to express my appreciation to the Chairman and the various gentlemen who have taken part. I regret that others have not offered criticism, for honest differences of opinion often lead to the truth, and suggest new lines of work. An experiment has been made which bears on Prof. Sauveur's discussion and which helps to emphasize the conclusion that cementation is not a factor in the hardening of: the surface. Dr. Langenberg, of the Watertown Arsenal, has heated for me, in vacuo at 1,000° C., a piece of the metal containing a hard surface. The microstructure shows uniform distribution of carbon throughout the metal, showing that no carbon has been added to .the surface and heating in vacuo has prevented any oxidation of the surface.

Jan 6, 1917

By Henry Fay

THE erosion of guns is a complex problem which can be solved only by a detailed study of all the factors involved. In the present paper it is proposed to submit the results of observations and experiments which have extended over several years. Certain facts have been established and preliminary reports have been published.' Conclusions have been reached since then which, it is believed, are worth presenting for the purpose of promoting discussion, and with the hope that ultimately the whole truth will be known. The particular phase of the problem which will be presented here is the hardening of the inner surface of the gun tube. It has been known for a long time that after firing a large caliber gun for some time, the surface of the metal becomes hard and brittle, cracks, and wears away.2 The character of this phenomenon may be learned by an examination of some results which are typical, obtained from a detailed study of a 12-in. gun. The gun was trepanned and rings representing various sections of the gun were cut out for examination. The first ring represented the metal at the muzzle end, and the other rings were removed at approximately 120, 240, 325 and 337 in., respectively, toward the breech end. The appearance of the surface of the metal in the different sections is shown in Fig. 1. The greatest amount of wear and maximum amount of hard surface layer was found in section marked E, which is nearest the powder chamber and at the beginning of the rifling; the maximum amount of cracking in D; the maximum amount of copper deposition in C. Section B showed heat cracks on both lands and grooves, and section A showed heat cracks on the driving edge of the lands only. There was much flow of metal in both sections E and D, and there was progressively less effect noticeable toward the muzzle end. The polished cross-section of these same pieces is shown in Fig. 2. The

Jan 12, 1916

By Henry Fay

LAWRENCE ADDICKS, New York, N. Y., (communication to the Secretary *).-There are two points regarding gun erosion on which I want to say a few words: The first is about the analogy to hardening of wire by drawing and the second the possible role played by thermal conductivity of the metal. The ductile metals do not necessarily become brittle when cold-worked as it is possible to draw copper from 3. in. in diameter soft rod down to the finest hair wire without annealing. This results, as stated in the paper, informing a hardened core with a very hard skin. The electrical conductivity is depressed some 3 per cent. and the tensile strength nearly tripled. A soft copper wire 0.08 in. in diameter and 6 in. long may be twisted 150 or more turns before the wire will snap under torsion. A hard-drawn wire will break after perhaps a dozen twists, the skin breaking down at one spot. Just wiping the wire with a cloth clamp with dilute nitric acid has a remarkable effect in increasing the number of twists without appreciably lowering the tensile strength, showing the skin to be very thin. On the other hand, pickling the rod, from which the wire is to be drawn, in dilute nitric acid also greatly increases the number of twists which can be applied to the resulting wire. This indicates that the copper oxide scale produced when the wire bar is rolled hot is more or less rolled into the rod and may have much to do with the skin effect. We also know that if the conditions of drawing are not correct, the heat of deformation in the die may produce quite an annealing effect. The application of this analogy to what occurs in a gun to produce the effects noted offers some difficulty. The second point is that as the temperature of the surface of the gun bore has undoubtedly a great deal to do with the amount of erosion, one natural remedy would be to conduct the heat away fast enough to keep this temperature within desired limits. This brings up the question of the thermal conductivity of the metal of which the gun is made. We know that the conductivity of pure metals is greatly altered by alloying and that the alloy is usually, though not always, lower in conductivity than the metal before alloying. This is interesting when it is considered that the high-nickel and manganese-steel alloys show greater erosion as stated. Would it not be instructive to study the question from the point of view of heat conducted away from the eroded surface?

Jan 3, 1917

By Henry Fay

THE CHAIRMAN (ALBERT SAUVEUR, Cambridge, Mass.).-In forcing us to face and to discuss the important question of erosion of steel guns, Prof. Fay is performing a public service. His investigation has been fruitful and his results illuminating and suggestive. It is not in a spirit of adverse criticism, therefore, that I venture a few remarks suggested by his paper, but rather to add my mite to the discussion in the hope that it may not be entirely without value. Prof. Fay considers it conclusively demonstrated that the hard layers forming in the inside of guns of large calibers after they have been fired a number of times consist of martensite. Still, he admits that he never was able to detect in the hard layers the structural characteristics of martensite. This leads him to conceive the existence of amorphous martensite. We may well hesitate before accepting this theory on the strength of the evidence offered. Martensite, as we know it, is essentially a crystalline condition assumed by a close association of iron and carbon, possibly if not probably of the nature of a solid solution. Lacking this crystalline character we are hardly justified in calling it martensite on the ground, merely, of its being very hard.

Jan 4, 1917

By S. G. Hardcastle

The effects of air velocity in promoting cooling through the evaporation of sweat generated when working at a high metabolic rate and/or in hot environments is well known. Many of the environmental heat stress indices consider the effect of air movement directly or indirectly within their determination, be it through the use of a specific instrument i.e. a wet-bulb globe temperature meter or Kata thermometer, or inclusion of in the calculation of a stress index, including the effective temperature, air cooling power, thermal working limit, ISO 7933?s predicted heat strain model. Within these models, ambient air temperature, relative humidity and barometric pressure are also considered in varying degrees to quantify an airstream?s capacity to evaporate sweat. Deep mine studies have shown cumulative increases in heat exhaustion rates with both decreasing air velocity and decreasing air cooling powers. However, despite a capacity to cool, the resultant cooling is very dependant on sweat production and its availability for evaporation; these are included where sweat rates and skin wettedness are considered. The first depends on hydration and physiological factors whereas the second is more an engineering factor related to the degree of clothing required. As sweat rates deteriorate with aging, the benefits of evaporative cooling potential can similarly be expected to be diminished. This paper continues to report upon on-going physiological studies exploring the potential for heat stress in deep underground mines through the simulation of mining activities in environmental chambers and a human calorimeter facility. The focus of this paper is to introduce preliminary data suggesting that increasing air velocity (0.5, 1.5 & 3.0 m/s) is beneficial for young subjects (22 ± 1 yrs), as indicated by lower core and skin temperature measures and heart rate during an intermittent work protocol, and then show a lesser benefit for older subjects (62 ± 2 yrs). Both subject groups performed the same task under the same environmental condition (35°C, 60% RH) wearing a standard mining ensemble. The study similar to others being performed under the Deep Mining Research Consortium funded research continues to provide evidence that a greater understanding of heat management processes is required and that worker education is critical as environmental measures and health and safety regulations may not be expected to include all demographic factors such as age, sex and health which are known to affect human thermoregulatory response.

Aug 1, 2013

By T. Haubold, K. Ortner, T. Jung, D. Roth-Fagaraseanu, C. Mattern

Application of integrally bladed disks (blisks) is of increasing interest in compressors of aero engines. Blisks are preferred due to their potential for size and weight reduction, for increased performance and for reduced manufacturing costs compared to conventionally bladed disks. Erosion of the blisk aerofoils in service reduces engine performance, and can result in short shop visit cycles. This significantly increases the life cycle cost of these components, particular when considering that eroded aerofoils can't be exchanged easily for blisks during refurbishment. Shop visit cycle times can be extended and maintenance costs can be reduced through the application of an effective protective coating. The ongoing development of an erosion resistant coating and deposition process suitable for coating complex blisk geometries is described here. The coating is a multilayered W /TiB2 system exhibiting superior erosion resistance compared to known single- and other multilayer concepts. A modified sputter process is used to enable coating even of blisk geometries with shadowed surface to competitive recurring cost.

Jan 1, 2006

By A. E. Bellis

THERE is a wide difference of opinion among rifle experts in the matter of barrel steel, and the relative importance to the life of the barrel of the steel's composition, heat-treatment, structure, and physical properties. In order to promote discussion, which it is hoped may lead to the discovery of the source of 'some of the traditional beliefs on the subject, the results of some tests are presented here, with data on heat-treating, physical tests, and erosion. The detailed metallographic study of this steel is given in another paper.1 The conclusions from these tests should be capable of wider application than their direct bearing on the barrel-steel problem. The Government specifications for barrel steel for model 1903 rifle (Springfield) call for carbon 0.50 to 0.60 per cent., manganese 1.00 to 1.29 per cent., silicon under 0.25 per cent., sulfur under 0.06 per cent., phosphorus under 0.08. per cent. The minimum physical requirements are: Tensile strength,- 110,000 lb. per sq. in. (7733 kg. per sq. cm.); yield point, 75,000 lb. per sq. in (5472 kg. per sq. cm.); elongation, 20 per cent.; reduction of area, 45 per cent. Material fulfilling these requirement's gives practically no failures when proof-fired, with charge of 70,000 lb. per sq. in. pressure, which is 40 per cent. in excess of the service charge. The turning and drilling operations show up any seams or laps such as accidentally occur even in- the best heats of open-hearth steel, so that' faulty stock is practically all eliminated before proof-firing. These physical requirements are met either by rolling billets at, a proper temperature clown to the form of tapered barrel blanks or by heat-treating bars that have been upset to enlarge the breech section. The transformation temperature of this steel, on heating, is around 1350° F. (732° C.), varying somewhat with the composition and the rate of heating. The actual treatment of the barrel blanks, as carried out by different

Jan 7, 1919

By A. M. F. Carter

A survey was conducted so that the degree of corrosive, erosive, and abrasive attack on material-handling systems in the mining and mineral-processing industry could be assessed, and so that the areas of research and development that would be relevant to the needs of the industry could be determined. Of the 59 different mines that were invited to participate in the survey, 41 returned completed questionnaires, giving a return rate of 70 per cent. The total number of completed questionnaires amounted to 45. An analysis of the results shows that attack by erosion or abrasion is considered to occur more often than attack by corrosion. However, al three types of attack must be regarded as significant problems within the mining industry, since 52 per cent of the participating mines reported pump failures due to the inability of the materials of construction to withstand the operating conditions, and almost 90 per cent reported piping failures due to corrosion (22 per cent) or to erosion and abrasion (78 per cent).

Jan 1, 1986

By Niraj Bala

Boiler tubes of coal-fired boilers suffer severe erosion-corrosion (E-C). One method to counteract this problem is by the use of therma, spray protective coatings. Cold spray coating process was used to deposit Ni-20Cr powder on SA 516 (Grade 70) boiler steel. The bare as wel, as the coated steels were subjected to cyclic experimenta, studies, in the superheater zone of a coa, fired boiler. The weight change technique was used to establish kinetics of the erosion-corrosion. XRD, FE-SEM/EDS and X-ray mapping techniques were used to analyse the as-sprayed and corroded specimens.

Jan 1, 2010