Search Documents

By G. Auld

"A simple method is presented whereby the additional quantity and static pressure necessary to compensate for ventilation duct leakage may be estimated using the circular reference functions of modern spreadsheets. Favourable comparisons have been made to the National Coal Board (United Kingdom) design charts and to a case study analysis. IntroductionIn mining, most ducted systems are applied to the development of access tunnels, and most of these systems leak to some extent. When the ventilation duct fails to deliver the required quantity of air to the work place, there is a significant contribution to the development costs, either directly or indirectly.Directly — More air and more pressure are required to compensate for the leakage, more capital development (ventilation shafts, parallel drives) are required because ventilation systems cannot push the fresh air far enough, and longer re-entry times to ensure toxic blast fumes to be diluted.Indirectly — There is a reduction in productivity because of the inclement atmospheric conditions, and/or closure of development ends because of unacceptable atmospheric conditions at the working place. This has been exacerbated over the last few decades because of the increased use of diesel equipment of ever increasing power, and the more stringent Occupational Health and Safety requirements demanding more air flow per kilowatt of diesel power.The leakage from a duct must, therefore, be reliably estimated in order to assess the effectiveness and construction of the system; assess the effectiveness of the maintenance or repair of the duct; appreciate the cost of the leakage, and therefore apply effective maintenance and installation procedures; and engineer safer, healthier and more cost-effective ventilation systems."

Jan 1, 2002

By T. Yalcin

"This paper describes the development of a mathematical model for determining the liberation of an ore at various grinding sizes, based on the combined results of microscopic counting, grinding tests, and chemical analysis.The method is illustrated with an application to the magnetite ore of Sherman Mine in Temagomi, Ontario. For this ore, a degree of liberation of 98.7% was determined at a grinding size of 90% passing 44 microns, which closely corresponds to the final grinding size employed at the Sherman Mine Concentrator.Introduction Liberation characteristic of ores have direct and significant bearing on overall economics of concentration processes.Target grades and recoveries can be achieved only it minerals are adequately liberated prior to separation. Degree of liberation depends on the extent of size reduction. However, due to the high costs associated with size reduction processes, it is important to keep size reductions within limits of satisfactory liberation. Prevention of excessive size reduction is also necessary because of inefficient mineral separations in very fine sizes. Hence, a study of reduction size — liberation relationship is essential for optimum profit from milling operations.A number of procedures have been developed for liberation studies (1-12), but there is lack of method for universal adoption.A new approach is presented in this paper that might provide a realistic estimate of liberation and give a practical guidance as to the degree of size reduction required for satisfactory liberation."

Jan 1, 1985

By S. Yamashita

Recently in Japan, unexpected degradation (surface subsidence) at old underground quarry sites, such as 'Ohya-Ishi' (pumice tuff) pit field has often been occurred. At these quarry sites, the excavation was started 20 or 30 years ago with mechanical chain cutter and the Room and Pillar method, and stopped 7 or more years ago. Therefore, a reliable method has been required for an estimation of long term mechanical properties of the rock and for an observation of a stability of rock-pillars or structures. In this study, creep tests under uniaxial compressive load were carried out on the 'Ohya-Ishi', with the aim of estimating the long term stability of the rock. From these results, a creep mechanism of the rock was discussed using the failure mechanism hypothesis proposed by Bieniawski and by others. On this basis, critical time to failure was predicted by the relationship between the logarithm of life time and stress ratio of the sustained axial creep load. Additionally, outline of the monitoring system of AE/MS activity in the field, which have set by the Ohya Aria Consolidate Public Corporation and the others to predict or to prevent the degradation of those residual pillars, is to be reported. Key words : Ohya-ishi, Pumice tuff, Mine pillar, Long term stability, Creep, Critical time

Jan 1, 1996

By R. H. T. Garnett

Reserve estimation is a process that commences with sampling and culminates in the issuance of a reserve statement. The tin, gold and diamonds that occur as marine placers on the continental shelf are low grade with very erratic mineral distributions. Sampling, using a variety of special equipment, determines the extent and grade of the mineralization. The sample size is important, especially for diamonds. Together with the sampling density, it determines the accuracy of the grade estimate. Bulk sampling is a confirmatory process. The choice of mining equipment, either new or developed from onshore activities, dictates the unit costs, the cutoff grades and the selectivity of extraction. Thus, the size of the blocks that comprise the mining plan and the reserves are determined. A variety of estimation methods of different reliability are available, with the most sophisticated being kriging. Dilution and losses during mining must be taken into account in estimation, and a grade-volume curve should be constructed. Diamond deposit estimation also involves an extra variable, the dollar value of the stones. During and after mining, essential feedback on the accuracy of un estimation may be given by the RIE factor and by a mineral balance. Reserve estimates are required for several reasons and may be subject to public disclosure. The use of the correct definitions is, therefore, important.

Jan 1, 1999

By Ramin Motamed, Anna Panorska``, Joseph A. W. Toth

In this study, a dataset of 145 bi-directional and static load tests was used to evaluate the load-displacement response with respect to unit side resistance for drilled shafts comprising fully and partially mobilized data. A total of 612 unit side resistance curves were calculated which included 52 fully mobilized curves showing a maximum response. A new approach using the double tangent method, is proposed in calculating the maximum unit side resistance from partially mobilized load-displacement data. The double tangent method was applied to each load-displacement response to estimate the ratio of mobilized resistance between the intersecting tangents and peak measured resistance. It is observed that as the mobilization of side shear approaches a maximum, the ratio approaches unity. Using the fully mobilized curves, regression models were developed using correlations between ratios of estimated resistance at the double tangent, peak, and maximum measured responses. Regression models are evaluated for the following factors: predominant soil type and drilled shaft construction methods. Comparisons of calculated and measured maximum values of unit side resistance are compared for each model. Although these factors each influence the load-transfer behavior, a single global regression model including all the data showed promise in yielding accurate results.

By L. Wade, R. Wang, M. A. Horton

Laboratory methods to find the mechanical properties of rock are inherently biased towards stronger strata, which best survive the sample preparation process. Geophysical techniques are not subject to such bias and may be used to predict mechanical properties rapidly and cheaply. Samples (151) were obtained from a borehole that had been comprehensively geophysically logged. The mechanical properties of the samples were established in the laboratory and correlated with the geophysical responses of the strata from which they came. The results indicate that, for homogeneous strata at least, it is possible to predict the unconfined compressive strength reasonably well from sonic travel time measurements made in the field. Predictions of static Young's modulus may also be made from this data source, but with a lesser degree of confidence. A multivariate regression equation is presented which relates down-hole sonic travel time to unconfined compressive strength, depth and the frequency of fractures in the rock mass. This equation may offer potential for the prediction of the mechanical rock properties of fractured and layered strata.

Jan 4, 1993

By T. E. Bernard

"Refuge alternatives (RA) provide shelter to miners trapped underground during a disaster. RA manufacturers must demonstrate that their RAs meet the Mine Safety and Health Administration (MSHA) requirements for oxygen supply, carbon dioxide removal, and the management of heat that results from the RA occupants and mechanical/chemical systems. In this study, miner size and activity level were used to determine the metabolic heat rate, oxygen requirements, and carbon dioxide generation that is representative of miners in a refuge situation. A convenience sample of 198 male miners was used for the distribution of current US coal miners, and the composite 95th percentile height and weight were determined to be 193 cm (76 in) and 133 kg (293 lb). The resting metabolic rate (RMR) was determined to be representative of activity level in an RA. The highest likely metabolic heat generation ranged from 115 W to 135 W, depending on RA occupancy. The highest required oxygen supply and carbon dioxide removal were estimated to be 23 LO2/h/person (0.81 ft3/h/person) and 20 LCO2/h/person (0.71 ft3/h/person), which means the margin of safety is 50% or more when compared to the MSHA requirements. INTRODUCTION Refuge alternatives (RAs) provide shelter to miners trapped underground during a disaster. Manufacturers must demonstrate that their RAs meet Mine Safety and Health Administration (MSHA) requirements for the supply of oxygen, the removal of carbon dioxide, and the management of heat that results from the occupants and the mechanical/chemical systems in the RA [1]. These MSHA requirements were based on a standard 70 kg (168 lb) male with an assumed allocation of activity of 80% rest and 20% moderate activity level [2]. The purpose of this paper is to re-examine the metabolic heat generation and oxygen and carbon dioxide requirements of miners in an RA based on actual miner size and more realistic RA activity levels based on current RA designs. The purpose of this paper is to re-examine the Mine Safety and Health Administration (MSHA) requirements for oxygen supply, carbon dioxide removal, and heat generation. To achieve this, researchers took the following steps to estimate the metabolic demands and the associated heat generation, oxygen requirements, and carbon dioxide production. 1. Characterized the anthropometric characteristics of the miner population. 2. Described the metabolic rate profile of RA occupants. 3. Characterized the maintenance demands of RAs. 4. Summarized oxygen supply and carbon dioxide removal volumes. ANTHROPOMETRIC CHARACTERISTICS OF MINERS The weight, height, and age distributions of the adult male populations are summarized in Table 1. For each data set, the reported mean and standard deviation are provided. The 95th percentile (%ile) value for height and weight for each population was the mean plus 1.64 times the standard deviation."

Jan 1, 2017

By T. E. Bernard

"Refuge alternatives provide shelter to miners trapped underground during a disaster. Manufacturers must demonstrate that their refuge alternatives meet the U.S. Mine Safety and Health Administration (MSHA) requirements for oxygen supply, carbon dioxide removal, and management of heat from the occupants and mechanical/chemical systems. In this study, miner size and activity level were used to determine the metabolic heat rate, oxygen requirements and carbon dioxide generation that are representative of miners in a refuge situation. A convenience sample of 198 male miners was used for the distribution of current U.S. coal miners, and the composite 95th percentile height and weight were determined to be 193 cm (76 in.) and 133 kg (293 lb). The resting metabolic rate (RMR) was determined to be representative of activity level in a refuge alternative. The highest likely metabolic heat generation ranged from 113 to 134 W, depending on occupancy. The highest required oxygen supply and carbon dioxide removal were estimated to be 23 L (0.81 cu ft) of oxygen per hour per person and 20 L (0.71 cu ft) of carbon dioxide per hour per person, which means the margin of safety is 50 percent or more compared with the MSHA requirements. The information on metabolic heat generation can be used to assess refuge alternative thermal environments by testing or simulation. The required oxygen supply and carbon dioxide removal can be used to assess refuge alternative requirements. IntroductionRefuge alternatives provide shelter to miners trapped underground during a disaster. Manufacturers must demonstrate that their refuge alternatives meet U.S. Mine Safety and Health Administration (MSHA) requirements for the supply of oxygen (O2), removal of carbon dioxide (CO2) and management of heat resulting from the refuge alternatives’ occupants and mechanical/ chemical systems (MSHA, 2008)."

Jan 8, 2018

Common practice in mineral resource estimation consists of partitioning the orebody into several domains defined by grade intervals, prior to the geostatistical modelling and estimation/simulation at unsampled locations. This paper shows the pitfalls of grade domaining through a case study in which we compare the performance of several estimation schemes and demonstrate that the use of domains defined by grade cut-offs implies a deterioration of the resource estimates, mainly in what refers to precision and conditional bias. Then, several conceptual limitations of the grade domaining approach are stressed, in particular the fact that it does not account for the spatial dependency between adjacent domains and for the uncertainty in the domain boundaries. Also, this approach is shown to be sensitive to the cut-offs that define the domains, to provoke artifacts in the kriging maps, histograms and scatter grams between true and estimated grades, and to lower the kriging variance, a feature that may impact the mineral resource classification. An alternative approach is finally proposed to overcome these limitations, based on a stochastic modelling of the grade domains and a co-kriging of the grades using information from all the domains. Keywords: geostatistics, kriging, conditional bias, geological control, grade zoning.

Jan 1, 2005

By W. Z. Choi

In our previous work, a population balance model describing the simultaneous processes of size reduction and mineral liberation has been developed. The experimental verification of this model, however, has been limited to a binary mineral system containing only one composite particle class. When considering multiple classes of composite particles, the estimation of model parameters becomes much more difficult. In the present work, a procedure for estimating model parameters for a multiple composite class model has been developed. Emphasis is placed on the direct experimental determination of these parameters. The physical significance of the breakage rate function and the liberation function in characterizing the liberation process is also discussed.

Jan 1, 1987

By R. Zivojinovic, S. Vujic, T. Tanaskovic

The problem of determining the optimum exploitation life of machinery, namely the optimum time for machinery and equipment replacement, represents a complex and highly responsible engineering task. Taking into consideration the situation prevailing at coal pit mines in Yugoslavia, the tasks of this class are very complex and difficult. To make a decision on replacement of capital equipment and machinery, such as bucket wheel excavators within the mentioned systems, understands a management task of utmost responsibility. It requires high professional and analytical knowledge as well as the reliable arguments, based on multidisciplinary professional approach. In this paper, the authors present their views on the problem of establishing the optimum exploitation life of bucket wheel excavators, offering an algorithm, based on dynamic programming, as a solution. Keywords: Bucket wheel excavators, exploitation life of machinery, optimization, operations research, theory of replacement, dynamic programming

Jan 1, 2003

By Sunil Bodakunta, Sreenivasa Rao Islavath

The abstract highlights the importance of determining the optimum line of extraction in continuous miner workings for improved safety and productivity. The study investigates three extraction techniques (diagonal, straight line along strike, and straight line along dip-rise) using 3D numerical modeling. The dip-rise extraction technique is found to be optimal due to lower stress and displacement, leading to a higher safety factor. The research also develops a continuous miner stability index (CMSI) to predict working face stability based on mining depth and pillar width-to-height ratio.

Apr 28, 2022

By C. Balci

Specific energy is defined as the amount of work required to break a unit volume of rock and is used to predict the performance of mechanical miners. It is obtained from full-scale rock cutting experiments, which require large block samples, experienced personnel and expensive equipment found in only a few research centres in the world. Estimation of the optimum specific energy, at which a given geological formation is excavated at optimum cutting geometry in the most energy efficient manner, from mechanical rock properties to predict the performance/efficiency of roadheaders is the basic aim of this study. The mechanical rock property tests require only core samples, which are easier to obtain and to test. In this context, full-scale rock cutting tests are performed on 23 different rock, mineral and ore samples including sandstone, claystone, tuffite, chromite, trona and copper collected from some operating mines in Turkey. The optimum specific energy values are obtained for each sample. Physical and mechanical property tests are performed on the core samples obtained from the same samples to determine uniaxial compressive strength, indirect (Brazilian) tensile strength, static and dynamic elasticity moduli, Schmidt hammer rebound values, density, and Cerchar abrasivity index. The relationships between the optimum specific energy and the mechanical rock properties are analysed using statistical methods. The results indicate strong relationships between the optimum specific energy and the mechanical rock properties. The strongest relationships are found by using uniaxial compressive strength and tensile strength. The performance models developed in this study are in good agreement with the empirical models previously developed for roadheaders and can be used reliably for prediction purposes. Keywords: Mechanical excavation, roadheader, performance prediction, rock cutting, optimum specific energy, mechanical properties of rocks.

Jan 1, 2004

By S. Mohanan, C. R. Kumar, S. K. Bhoja, T. Venugopalan

"A pressing issue that has often been the topic of discussion in iron-making operations in India is the high content of alumina in the country’s iron ore deposits. The presence of alumina has hampered production by affecting slag fluidity, and thereby the hot metal quality. Iron ores from Indian mines are generally rich in hematite, with traces or small amounts of goethite/limonite, kaolinite, gibbsite and quartz reported from time to time. In day-to-day production, emphasis is placed on checking the chemical analysis of product samples, but the true solution to the alumina problem lies in estimating the mineralogy of the ore samples. We developed a mathematical model, based on singular value decomposition, to predict mineralogy from classical chemical analysis. We then used X-ray diffraction patterns, scanning electron microscope analysis, and grain counting with an optical microscope to determine actual mineral compositions and to test the values predicted by the model. The results indicate that with regular calibration, the model can be used as a simple, fast and effective tool to predict on a regular basis the mineralogy of multiple samples.IntroductionIndian blast furnaces use high-grade iron ores (as lumps or as sinter) and coke (obtained from the destructive distillation of coal) as raw materials for the production of high-quality hot metal to be converted into different steel products through the Linz- Donawitz process. The iron ores are mainly sourced from the Singhbhum region of Odisha and Jharkhand states, the Bailadialla region of Chattisgarh state and the Bellary region of Karnataka and Goa states, and are mainly classified based on size as (1) lump ore (fed directly into blast furnaces), (2) fines (converted into sinter/pellets and fed to blast furnaces) and (3) slimes (< 0.15 mm; currently dumped in huge slime ponds). Any variation in the quality of the ores supplied results in variations in the production trends of hot metal."

Jan 1, 2015

The ore reserves of the Frieda porphyry copper prospect in Papua New Guinea have been estimated using kriging and an alternative method. Only very erratic variograms could be obtained from the raw data and thus it can be expected that kriging variances will be unrel- iable. The frequency distributions of the two sets of estimates show expected differences and the resulting mineable reserves show similar expected differences. More drilling and the use of disjunctive kriging are needed to produce reliable estim- Ates.

Jan 1, 1979

By W. H. Basssett

THE amount of oxygen present in refined copper bears an important relation to the effects of various impurities on physical properties of copper, as well as the effects of reducing gases at higher temperatures. It seems fitting at this time, when the effects of reducing gases on copper are being discussed, to describe methods that have proved satisfactory for the determination of oxygen and sulfur, and to present some results obtained by investigation of these methods in the authors&apos; laboratory. The procedure for the determination of sulfur is closely interrelated with that for oxygen and has, therefore, been included. It was first proposed by Hamper that oxides in copper could be accurately determined by the loss in weight sustained by finely divided copper when reduced at red heat in pure hydrogen, or by the weight of water produced. Hampe&apos;s method was later modified by Archbutt,2 who established the accuracy of the method and demonstrated that equally accurate results were obtained by noting the loss in weight or by weighing the water formed. The determination of oxygen by heating in carbon monoxide has been proposed by West.3 In our hands this method has given slightly lower results than obtained by heating in hydrogen.

Jan 2, 1926

By R. Hogg, T. H. Dumm

"The mathematical treatments used in the evaluation of particle size distribution from pipet-withdrawal centrifuge data are reviewed. An error in the published procedure for multiple-sample withdrawal systems is pointed out and a corrected formulation is presented. An alternative treatment, based on a piece-wise linearization of the size distribution is described. Computer simulations of the analytical and data evaluation procedures indicate that the errors in the original formulation are not generally serious and that the corrected and alternative procedures lead to very similar estimates. Except for some cases involving very narrow size distributions, the alternative approach appears to give slightly closer estimates of the size distribution. Comparisons based on actual experimental data are also described.1 IntroductionSedimentation methods are widely used for the determination of particle size distributions. The procedures are relatively simple to use and the results are essentially absolute, requiring no external calibration. Gravity sedimentation is typically applicable to particles in the size range of about I to 50 pm and generally involves measurement of the relative concentration of particles as a function of depth and time in a dilute suspension. Particle size is calculated using Stokes, law:"

Mar 1, 1989

By P. P. Gregory

ESTIMATION of re- serves in prorated sand fields has been discussed by S. A. Judson, H. D. Easton, Jr., and W. A. Schaeffer, Jr., in a paper that appears in Vol. 114 (1935), of the A.I.M.E. TRANSACTIONS. The purpose of this present paper is to extend the investigation to prorated flush limestone fields and to outline a method of procedure in determining the amount of oil originally in place and the amount of oil that can be recovered from such fields. Although it is possible to use the decline curves to estimate the amount of recoverable oil in certain limestone fields that are allowed to produce the oil at or near capacity production, such a method cannot be used in fields under severely restricted production rates. The problem is exceedingly complex due to fluctuation in the allowable rates of oil production over a wide range and at frequent intervals, and especially because of the heterogeneous nature of the reservoir itself. A well completed in a large solution cavity, capable of producing great quantities of oil per day, may be offset by a well of very limited capacity. Also, it is di5cult to arrive at an average figure for porosity in a given limestone reservoir due to abrupt variations in the character of limestone, in many instances even between two ad- joining wells. It is a safe statement that uniformity of porosity and permeability in limestone reservoirs .is nonexistent. It is evident, therefore, that the method of estimation of re- serves on the basis of per-acre content can give only approximate results.

Jan 1, 1935

By Fan Yang, Meigui Yi, Lan Xiang, Zhuoying Yang

This paper reported the calculation of the reaction heat in titanium-bearing blast furnace slag (abbreviated as TBFS)-H2SO4 system based on estimation of thermodynamic data of CaTiAl2O6 by mechanical mixture model. The thermodynamic analysis indicated that CaTiAl2O6 was more stable than the corresponding ternary oxides as CaO·TiO2, CaO·Al2O3, and Al2O3·TiO2. TBFS-H2SO4 system was highly exothermic since all of the reactions involved in the system were exothermic. For example, the increase of temperature from 25 to 200°C led to the increase of the release of the reaction heat in TBFS (100.0g)-H2SO4 system from 181.28 to 189.73kJ. Eighty-five to 90%of the reaction heat in TBFS-H2SO4 system was contributed by the reactions among CaTiAl2O6, CaTiO3, CaMgSi2O6, and H2SO4.

Feb 1, 2021

By D Fukuda, K Kaneko, R Kudo, J Kodama, Y Fujii, T Sasaki

"Estimation of stress state as well as elastic modulus is important for the prediction of a rock slope deformation in an open pit mine since it can strongly influence the mining-induced deformation of the rock slope. This study applies a method to evaluate regional stress state and Young’s modulus by analysing the mining-induced deformation of ground. The effect of changes in regional strain state due to tectonic plate motion can be accounted for using the proposed method. Mining-induced deformation can manifest itself as changes in ground surface geometry resulting from mining activity. There are three underlying factors that can contribute to the deformation: displacement induced by the effect of gravity displacement induced by the effect of horizontal regional strain incremental change in the horizontal regional strain. The relative displacement arising from the mining excavation at the Torigatayama limestone mine in Japan has been measured by Global Positioning System (GPS). Both the regional stress state and Young’s modulus were estimated by back analysis of the change in distance between GPS stations using a 3D finite element method. It was shown that the reliability of the estimation improved with an increase in displacement due to mining progression. It was also shown that values for Poisson’s ratios of less than 0.10 are reasonable estimates with values for Young’s modulus between about 5?GPa and 10 GPa. The magnitude and direction of the maximum compressive stress in the district surrounding the Torigatayama mine were estimated to be between -6.4 MPa and -4.4 MPa and around N25E respectively.CITATION:Kodama, J, Sasaki, T, Fukuda, D, Kaneko, K, Fujii, Y and Kudo, R, 2014. Estimation of regional stress state and Young’s Modulus of ground at Torigatayama Limestone Mine in Japan, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 135–142 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014