Search Documents

By R. L. Wolfrom, R. Hogg, S. Chander

A gravimetric method for measuring rates of capillary rise in powders was explored. Methods to improve reproducibility and consistency of the results were investigated. In particular, the effects of particle size and packing uniformity were addressed. Studies of the wetting behavior of both spherical glass beads and irregularly shaped synthetic graphite particles by various organic liquids were carried out. Standardized procedures for bed preparation are described. The applicability of the Washburn equation for surface energy evaluation in such systems is discussed.

Jan 1, 2002

By M. A. Aziz

The electrochemical performance of a series of carbon materials produced from coconut shells, which are very cheap and readily available in Bangladesh was investigated for their viability as anode materials in rechargeable lithium-ion batteries. X-ray diffraction technique was used to measure the interlayer spacing (d002) of the produced carbon materials. A number of half-cells were prepared with the produced carbon materials from coconut shell as working electrode and metallic lithium as counter electrode with 1MLiPF6 electrolyte in a mixture of ethylene carbonate and dimethyl carbonate. The discharge-charge profiles were measured for the different half-cells by using Arbin 24-channel Cyler. The value of interlayer spacing of the coconut-based carbon material was found to be 0.397 nm at 900°C, which is most suitable for lithium-ion insertion into the carbon structure without any expansion. The specific discharge capacity of carbon material from coconut shell heat treated to 900°C was found to be 1015.65 mAh/g. The coconut carbon material heat treated to 900°C delivered 335.22 mAh/g reversible capacity, which is comparable to the commercial carbon/graphite presently used in lithium-ion battery systems. The irreversible capacity loss and coulombic efficiency in 25th cycle of half-cell made with coconut carbon material were found to be 0.16% and 99.83% respectively. The carbon material produced from coconut shell can, therefore, be used as a potential anode for rechargeable lithium-ion batteries.

Jan 1, 2006

By Richard A. Thomas, III JAMES H. ROWLAND, Liming Yuan

This paper presents the results of large-scale fire experiments on evaluating the performances of carbon monoxide (CO) and smoke sensors at low ventilation velocities. Experiments using three different combustibles — conveyor belt, coal and diesel fuel — were conducted in the experimental mine at the U.S. National Institute for Occupational Safety and Health (NIOSH) Bruceton Research Facility. A total of eight sensor stations were located downstream of the fire with each station containing sensors for CO, smoke, carbon dioxide (CO2 ), oxygen (O2 ), humidity, barometric pressure and temperature, as well as two airflow sensors. The airflow velocity ranged from 0.22 to 0.26 m/s (44 to 51 fpm) in the tests. The response times were recorded for the CO and smoke sensors at each sensor station when smoke and gaseous products of combustion from each burning combustible reached the station. The response times of the CO sensors were used to determine the appropriate sensor spacing in the belt entry with a low air velocity. The performance of the smoke sensor was found to be affected by the high humidity in the experiments. The results on proper selection of sensors and the determination of sensor spacing at a low ventilation velocity can be helpful for ensuring sufficient early fire warning for underground workers, thereby improving the health and safety of miners.

By Felipe Fardin Grillo

The aim of this work was to study the use of slags to desulfurization of cast iron. It was proposed to use alumina instead fluorspar. In addition, marble waste was used instead lime. Simulations applying Thermo-Calc software were performed in order to obtain the theoretical phases thermodynamic data. Then, a comparison between theoretical data and experimental tests were performed. The cast iron was melting in induction furnace at 1550°C. Slags composed mainly for CaO and Al2O3 were used to cast iron desulphurization. It was observed that increasing liquid phase, the desulphurization reaction was favored. Besides, it was found that cast iron desulfurization occurs by top slag mechanism.

Aug 17, 2017

By Tony P. Suckling

This paper describes an investigation into the bleeding behaviour of bentonite slurry observed on a trial diaphragm wall panel. The bleeding is thought to be due to the bentonite experiencing a chemical reaction leading to settlement of the solids within the fluid, possibly as a self-weight consolidation process. The trial panel was constructed in a busy airport environment where many different chemical products are used for de-icing the aeroplanes, runways, apron areas, vehicle access and pedestrian routes. The relationships between slurry contamination, bleeding, bentonite hydration time and filter loss behaviour were examined as no relevant published literature could be found. The results show that the amount of bleed strongly depends on both the degree of contamination and the hydration time. It is concluded that bentonite fluids should be allowed to sit in the storage tank for at least 24 hours after mixing, and that the filter loss test is a quick and effective method to determine the potential for bleeding of contaminated slurries.

Jan 1, 2011

By M. Samuels

"Block and panel cave mining methods are being increasingly proposed as they allow massive, deeply situated ore-bodies to be mined economically at a time when discovery rates of significant near surface deposits are declining. Cave-to-Mill, a mine-to-mill approach for block cave mines, defines ore block models with respect to both mine and mill performance. A cave-to-mill study for the New Afton block caving operation focused on identifying value opportunities related to fragmentation and sorting for a future lift as development progresses deeper. The lack of selectivity and potential for dilution associated with the block cave mining method results in many caving operations having to mine and either dispose of or process material that is below cut-off grade at certain stages of production. As an outcome of the study, the variation in cave fragmentation size and the sensitivity of mill throughput to feed size was examined. To evaluate the amenability of bulk and particle sorting, Prompt Gamma Neutron Activation Analysis and X-Ray Fluorescence sensors were tested. A conceptual bulk and particle sorting flowsheet is presented. Grade data from regular underground sampling was used to predict the performance of a bulk sorter. A heterogeneity analysis of material reporting to drawpoints helped to identify areas of the extraction level that experience high variations in grade and thereby stand to benefit from dedicated ore and waste material handling systems should underground bulk sorting be implemented.INTRODUCTION Block and panel caving are low-cost underground mass mining methods that are suitable for excavating weak, massive and steeply-dipping orebodies. Accordingly, cave mining methods have predominantly been used to mine copper porphyry and diamond bearing deposits. Due to the increasing depletion of near-surface orebodies, it is expected that block and panel caving methods will be increasingly used in the copper-gold industry. Their implementation holds significant potential to extend the life of existing open-pit operations by providing an economic means to access ore located at depths that are beyond the practical limits of open-pit mining. Examples of cave mines proposed for British Columbia include the Kwanika Mine, Red Chris underground, Kemess Underground project, and the Iron Cap and Mitchell cave mines of the Kerr-Sulphurets and Mitchell (KSM) project (Moose Mountain Technical Services, 2017; Imperial Metals, 2017; Golder Associates, 2017; Tetra Tech, 2016)."

Jan 1, 2018

Ok Tedi Mining Limited has recently completed the first phase of a trial to compare the performance of D26B Krebs cyclones in different configurations to the new Warman 650 mm CAVEX cyclones. From 1992, rougher flotation feed size has increased from the target d80 grind size of 150 ¦m with increasing SAG mill throughput. At high SAG mill throughput, operators have difficulty maintaining the target cyclone feed pressure and must increase the cyclone feed density, thus resulting in a coarsening of the cyclone split. Warman International have developed the CAVEX high capacity cyclone. The new CAVEX cyclones, when compared to the Krebs units appear to:produce a measurable increase in volumetric flow for the same pressure drop; maintain or decrease the proportion of coarse particles reporting to overflow; and lower the overflow density. In all plant trials to-date, the CAVEX cyclones appear to be superior to the standard Ok Tedi Krebs cyclones. Further testwork is planned to evaluate modified Krebs cyclones (with recent design improvements) against the CAVEX cyclones.

Jan 1, 2000

By Donald Towse

Portland cement is a basic building material in every country in the world, and, fortunately, the raw materials required in its manufacture are widely distributed. It is a low-priced bulk commodity (price one cent a pound or less, with a density of 100 pounds per cubic foot.) Table 1. Approximate price per pound of selected mineral products. Copper 48 cents per pound Aluminum 27 Lead and zinc 15 Asbestos 3 to 18 Pumice 6 Sulfur 2 Bauxite (abrasive) 1.8 Barite 1 to 1.6 Cement 1 Primitive regions may get along without any Portland cement, but most countries use some, and it is one of the most widespread building materials, even if used in small quantities. Use of cement begins early in a country's development, and, because of local availability of raw materials, cement manufacture is one of the first heavy industries many countries desire. Use and manufacture of cement usually precedes other industrial materials such as steel and heavy chemicals, and consumption levels off for a long period during development of infrastructure and an economic base. With a mature economy comes a very high consumption. Per capita consumption varies ten times or more between nations (Figure 1).

Jan 1, 1970

By V. D. Smar

The flotation process may be considered an interactive system consisting of many chemical, operational, and equipment variables. Changing anyone of these variables causes an overall system response change. This study examines the effects of simultaneously changing the operating variables of: (1) frother concentration and air flow rate, and (2) frother concentration and collector concentration. It is part of a comprehensive study to look at how changes in several of the major variables may be used to produce interactions which will allow the rougher flotation process to be optimized. Ultimate recovery, flotation rate, concentrate grade and froth quality, are used as the major evaluative criteria.

Jan 1, 1993

By Rudi César Comiotto Modena, Gabriel de Castro Moreira, Diego Machado Marques

The definition of geological/geostatistical domains is the first step in building a mineral resource model. A suitable division for these domains requires some prior knowledge about the deposit geology and can be supported by a careful statistical analysis. It is crucial that data with similar characteristics are grouped together, to avoid the mixing of statistical populations, defining the so-called stationary domains. In order to assist in this definition, two unsupervised clustering algorithms were applied: Otsu and K-means. The first one is widely used in image segmentation and it is based on the exhaustive search of the data to determine the best threshold for separating them. K-means is one of the most used techniques in machine learning, and it is based on the iterative analysis of the statistical distribution. Clustering algorithms may present some shortcomings when applied to geological data, since they are based on pure statistical analysis, not considering spatial distribution or data location. Choosing the most appropriate number of domains can also be challenging. Some methods for defining the best number of groups are presented, based on the analysis of variances between/inside groups, supported by indicators variography in order to verify this definition.

Oct 3, 2019

By R. M. Rowe, A. K. Bhasin, D. Malhotra

Introduction Most primary molybdenite producers use a selective flotation process in which molybdenite is floated from the ore while other sulfide and nonsulfide gangue minerals are depressed in the same step. The process was developed at the Climax mill. Reagents used in the rougher flotation stage include vapor oil (collector), syntex (surfactant), pine oil (frother), and occasionally sodium cyanide and Nokes reagent (depressant). Rougher concentrate is upgraded by cleaner flotation to produce market-grade molybdenite concentrates. Reagents used in the cleaner flotation stage are Dowfroth 250, vapor oil, sodium cyanide, and Nokes reagent. The development of the flotation reagent scheme at Climax and the role of the reagents have been well described by Born et al. (1976) and Malhotra et al. (1976, 1977a, 1977b, 1977c, 1980). The hydrocarbon collector, vapor oil, accounts for approximately 50% of the total molybdenite flotation reagent cost. Because vapor oil sources are limited, and the cost of vapor oil has increased significantly over the last decade, several studies have been done to evaluate alternate oil-based collectors and/or blends of collectors that would produce similar metallurgical results at a reduced cost, or increase the overall molybdenite recovery at the same cost (Smit and Bhasin, 1983; Hahn, 1969; Smith and Bhappu, 1971). The approach taken in the present study was to evaluate alternate nonoil-based collectors and collector systems that are less expensive than vapor oil. A series of potential nonoil-based collector classes were identified and evaluated in the laboratory against the current collector system. The metallurgical performance of these collector classes was related to their chemical structures. The results of this study are discussed. Collector classes A survey of sulfide mineral collectors was performed with the objective of identifying and selecting potential collectors for molybdenite flotation. The available reagents were categorized into 10 general classes. Table 1 summarizes these collector classes, their chemical formulas, the manufacturers, and selected commercial collectors in each class that were evaluated in the present study. Experimental procedure A Climax ore sample, assaying 0.3% MoS2, 2.2% FeS2, 0.007% Cu, 0.003% Pb, and 0.03 oz per ton Ag, was used for this study. Standard laboratory rougher flotation test procedure involved grinding a 2-kg ore charge in a rod mill at 60% solids. Reagents were added to the rod mill including a collector, syntex (0.005 kg/t), pine oil (0.03 kg/t), lime (to adjust pH to 8), and sodium silicate (0.15 kg/t). The ground pulp was transferred to a 1000-g cell, and flotation was performed at 35% solids and 1800 rpm using a Denver D-1 flotation machine. Concentrate was collected for a flotation time of six minutes. The general approach used in the present study was to substitute the nonoil-based collectors at two to three different dosage levels (0.01 to 0.15 kg/t) for vapor oil in the bench-scale, open-circuit rougher flotation tests

Jan 1, 1987

By D. Malhotra

Most primary-molybdenite producers use a selective-flotation process in which molybdenite is floated from the ore while other sulfide and non-sulfide gangue minerals are depressed in the same step (Figure 1). The process was developed at the Climax mill. Reagents used in the rougher-flotation stage include vapor oil (collector), syntex (surfactant), pine oil (frother) and occasionally sodium cyanide and Nokes reagent (depressant). Rougher concentrate is upgraded by cleaner flotation to produce market-grade molybdenite concentrates. Reagents used in the cleaner flotation stage are Dowfroth 250, vapor oil, sodium cyanide and Nokes reagent. The development of the flotation reagent scheme at Climax and the role of the reagents have been well described by Born, et al, (1976) and Malhotra, et al, (1976, 1977a, 1977b, 1977c, 1980). The hydrocarbon collector, vapor oil, accounts for approximately 50 percent of the total molybdenite-flotation reagent cost. Because vapor oil sources are limited, and the cost of vapor oil has increased significantly over the last decade, several studies have been done to evaluate alternate oil-based collectors and/or blends of collectors which would produce similar metallurgical results at a reduced cost, or increase the overall molybdenite recovery at the same cost (Smit and Bhasin, 1983; Hahn, 1969; Smith and Bhappu, 1971). The approach taken in the present study was to evaluate alternate non-oil based collectors and collector systems that are less expensive than vapor oil.

Jan 1, 1985

By J. H. Tylczak, R. Blickensderfer

Impact and abrasion properties of various commercial US grinding halls were evaluated and compared by the Bureau of Mines, US Department of the Interior. Laboratory tests were conducted on balls obtained from eight major US manufacturers. The halls included forged steel, cast steel, and alloyed white cast iron and were subjected to repeated impacts until they broke or until 300,000 impacts were exceeded. Pin abrasion tests also were conducted. The results showed wide differences in impact lives, ranging from a few thousand to over 500,000 impacts. The life of inferior commercial halls was increased five to six times by a laboratory tempering heat treatment. For halls that did not break, the major impact wear mode was spalling and ranged from an average rate of 0.28 to 4.46 mg per impact. The softest halls (steel) had excellent impact resistance but low abrasion resistance. The abrasion resistance of the steel halls generally increased with hardness. The alloyed white cast irons had about twice the abrasion resistance of the steel halls. Users should become aware of the wide variations among commercial halls, and ball manufacturers should be aware that their product can he improved.

Jan 1, 1990

Evaluation of Comminution Circuit Design for Sustainability Using EcoNomicsTM

Sep 13, 2010

By R L. Verburg, R Johnstone

DeBeers Canada Mining Inc (DeBeers) recently submitted an Environmental Assessment (EA) for its proposed Snap Lake Diamond Mine located in Northwest Territories, Canada. As part of the EA process, a site water quality management plan must be developed. Plan development requires an integrated approach such that the key factors influencing water quality can be identified and managed to minimise potential impact. A system model was therefore developed to simulate the site-wide water quality conditions and mass loadings to the principal environmental receptor of concern, Snap Lake, during operations and post-closure. Requirements of the simulation included integrating hydrology, geochemistry, hydrogeology and site management practices in a dynamic way. A unique feature of the site was the need to accommodate a complex flow system that included a feedback loop between lake water and mine water. A system model was constructed using the GoldSim software package that integrated on-site water quality and flow measurements, as well as results from independent groundwater flow and geochemical modelling efforts. The GoldSim model simulated concurrently the movement of 39 solutes through the subsurface mine and surface facilities. Solute sources considered included four different waste rock and tailings types, explosives use in the mine, treatment plant discharge, and recycled process water for dust suppression. Separate solubility constraints were identified for different regions of the flow system (eg underground mine; treatment facility; surface water bodies). Kinetic test data were used to derive temperature-dependent rate constants for use in calculating mass inputs from surface sources such as waste rock piles. The model generated water quality estimates over time for a variety of management scenarios at several potential discharge locations. The integrated approach used by the model was effective in identifying the significance of key factors influencing overall water quality such as explosives use, mine water inflow rates, waste rock reaction rates, site/mine management options, and effectiveness of treatment. The model provides an example of an effective tool for comprehensive, integrated system evaluation and management.

Jan 1, 2003

By S. Tan

In this paper, several commonly used computer truck dispatching criteria are evaluated. A computer-oriented truck dispatching and production simulator was developed to provide data for comprehensive cross comparison among the dispatching criteria. The definitions, primary considerations, characteristics, and performances of these dispatching criteria were investigated. From the simulation results, it was concluded that, in general, no one criterion can dominate all others. All basic dispatching criteria including minimizing truck waiting time, minimizing shovel waiting time, minimizing truck saturation, maximizing truck momentary productivity, or truck routes optimization provide a local optimal solution. To obtain a direct global optimization solution for this complex stochastic process does not appear to be likely. Therefore, the search for an optimal dispatching criterion that will fit all conditions may not be realistic. However, based on the simulation results of the mine operation, several dispatching criteria which have good potential to increase performance can be selected. It may be necessary to search for the best combination of these truck dispatching criteria for a given situation. For example, a truck flow measurement such as the truck clustering factor at shovels can be used as a switch parameter to change from one criterion to another. The values for the switch parameter at which actions should be taken to change the criterion can be established through simulation programs.

Jan 1, 1992

By L. Yan, T. Lutz, J. Noll

"Mine disasters, such as fires and explosions, can create a hazardous atmosphere due to the generation of carbon monoxide (CO). After a mine disaster, contaminated mine air can enter the refuge alternative (RA) as miners enter. Most built-in-place (BIP) RAs use an air delivery system to provide an unlimited supply of breathable air through a borehole which also serves to purge contaminants. In order to determine what levels of contaminants enter the RA, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted testing in NIOSH’s Pittsburgh Experimental Mine using groups of 5, 15, and 30 subjects entering the RA. The experiment used sulfur hexafluoride (SF6) as a tracer gas that was released into the air outside of the BIP RA to establish a uniform concentration. After the human subjects entered the BIP RA, the SF6 levels inside the RA were measured to quantify how much of the tracer gas entered the BIP RA. In tests conducted while the borehole air supply was left off as test subjects entered, interior contaminant levels were less than 3% of the exterior concentration. In tests conducted with the borehole air supply activated as test subjects entered, the interior contaminant levels were measured at less than 2% of the exterior concentration. Considering a mine disaster can result in 10,000 ppm of CO in the mine atmosphere, these percentages indicate that unhealthy CO concentrations that may lead to headaches, dizziness, and loss of judgement can occur in a BIP RA. This information will help mines make decisions concerning air locks, air delivery systems and a determination if purging mechanisms are necessary. INTRODUCTION The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and enforcement of mine safety standards (MSHA, 2006). Section 13 of the MINER Act specifically directs the National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of RAs for underground coal mines. This mandate culminated in the 2009 adoption of changes to the 30 CFR mining health and safety regulations, requiring underground coal mines to provide RAs capable of maintaining a life-sustaining environment for persons trapped underground. Such RAs can be either pre-fabricated or BIP shelters. The regulatory changes also include provisions establishing requirements for Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe, breathable atmosphere within RAs."

Jan 1, 2018

By H. Sakurai, M. Kato, F. Tanaka

The Mitsubishi Continuous Copper Smelting/Converting Process employs an electric furnace (CL- furnace) for settling the slag/matte mixture formed in the smelting furnace. The conditions in the CL- furnace change its settling efficiency, resulting in high variability of copper losses in slag. Modifications of the operation and maintenance procedures for the CL-furnace have significantly and sustainably reduced the copper losses in Gresik smelter to below 0.7%. A series of flow patterns evaluation in the CL-furnace demonstrated how the chemical reactions and settling conditions of the CL-furnace has been improved by the new operating procedures. Settling mechanisms for the matte droplets in the CL-furnace is also discussed using image analysis of solidified slag. INTRODUCTION The Mitsubishi Continuous Copper Smelting/Converting Process employs an electric furnace (CL- furnace) for settling the slag/matte mixture formed in the smelting furnace. Since the top-blowing in the S- furnace agitates the molten bath strongly, matte droplets are dispersed over the slag phase when melts flow out of the S-furnace. Thus, the CL-furnace has an important role to settle and recover matte droplets efficiently. Since many papers have ascribed major part of copper losses to matte droplets suspended in slag (Tanaka 2007; Genevski et al., 2008; Starodub et al., 2016), flow patterns of slag in the CL-furnace can affect greatly on the profitability of smelters which have adopted the Mitsubishi process. PROCESS DESCRIPTION Figure 1 illustrates the Mitsubishi process schematically. The Mitsubishi process is the only system for continuous production of blister copper from copper concentrates and consists of 3 furnaces connected by enclosed launders those ensure the minimum emission of fugitives. In a smelting furnace (S-furnace) copper concentrates are fed with flux, oxygen-enriched air to form a mixture of slag and matte which cascades down to a slag-cleaning furnace (CL-furnace). The CL-furnace settle matte droplets in the mixture on the crucible from which matte is siphoned to a converting furnace (C-furnace), while discharging the cleaned slag (CL-slag). The C-furnace converts matte to blister copper by the top-blowing of oxygen- enriched air.

Jan 1, 2019

By Sina Mostaghel, M. Guo, E. Klaffenbach

The current paper is focused on evaluating the behavior of copper in a copper production slag and the assessment of metal recovery possibilities. For this reason, thermodynamic calculations were carried out to determine the influence of parameters such as slag composition, temperature and oxygen partial pressure on recovery of non-ferrous elements. It was found that the formation of a solid face centered cubic (fcc) phase, mainly consisting of iron, limits the extent of reduction that can be achieved for an industrial process. However, it could be discovered that solubility of iron in the Cu-rich liquid alloy strongly depends on presence of other elements, particularly arsenic. As part of the results of this study, the solubility of Cu in the slag at onset of fcc phase formation is presented as function of temperature, oxygen partial pressure and concentration of MgO and CaO. It was concluded that lower temperature (1200°C) and higher CaO addition (16 mass-% in this study), would result in the highest achievable copper recovery from slag. INTRODUCTION Copper slag is produced as a by-product of the copper production process. The slag is still containing a high amount of copper and other valuable metals. This demands further treatment of the slag as a secondary source of metals. In addition, the physical/mechanical properties of slag allow its use in several applications such as hydraulic engineering, civil engineering, as an abrasive and many more. These applications help reducing the use of natural resources like rock and sand. By decreasing the content of heavy metals such as Cu, Pb, Zn and As in the slag, its application in abovementioned fields becomes more attractive as the probability of releasing these elements to the environment is further reduced. To develop a pyrometallurgical slag reduction process, it is necessary to understand what describes the end point of the reduction. This point is expected at maximum copper recovery without facing operational challenges. Existing literature provide some information on the effect of different parameters such as temperature or concentration of different slag formers, on solubility of copper and heavy metals in different phases. However, due to complexity of industrial slags, equilibrium experiments and accurate thermodynamic modelling are essential to be able to reliably predict the behavior of different elements in the system and determine the end-point of reduction.

Jan 1, 2019

By A. Hosseini

Full-scale rupture tests were conducted on 508 mm (20 in) diameter API X-60 5.7 mm wall thickness pipes containing either axial semi-elliptical cracks or simulated corrosion defects with equivalent depths ranging from 20 to 60 percent thickness. In the case of the cracks, the failure pressures were predicted with reasonable accuracy when considering a level 3 failure assessment diagram (FAD) procedure based on API 579, as compared to level 2 FAD, since the mechanical properties were known. In both cases, the accuracy improved for shallower cracks. Considering simulated corrosion defects, the RSTRENG approach provided more reliable results on predicting the collapse pressure. For a similar depth and profile, the cracked pipes failed at a lower pressure than those containing simulated corrosion defects of equivalent depth.

Jan 1, 2010