Search Documents

By Luis R. Fonseca, C. Raimat, C. Wendeler, A. Sanz

"Rockfall barriers are widely known as proven efficiency element to protect infrastructure by catching the rock blocks in the falling direction and absorbing the energy generated by them.It’s common in the project design phase and during installation, fix rockfall barriers for catch a high percentage of the falling blocks and in many cases consider as valid the solution when the barrier can capture all of them. However, in many cases it’s possible to consider the use of these protections, simply to guarantee a secure shed for the traffic and intercept simply the blocks that theoretically hit the road surface.The results of the high-energy rockfall protection barriers type GBE which protect GC-200 road in Las Palmas de Gran Canaria are shown in this paper.The topographic data should be especially detailed observed and even more if you want to apply the technique of ""shadow zone"" with a flexible gallery system. It should be drawn from detailed topographic maps and drawings (photogrammetric restitution) to the scales 1/1000, 1/500, or 1/200; and it is important not to ignore the presence of vertical cuts, tracks, small slopes that modify the trajectories (trampoline effect, hard points that favor the rebounds) and which are not always presented in the drawings.The ""shadow zone"" is defined as the protected area, located at a lower elevation to the line created by the rockfall barrier to except of trajectories of rocks and free from the influence of the deflection of the system under the maximum energy level for which it was designed (MEL)."

Jan 1, 2015

By A. Zangooi, J. A. Finch

"A frother analysis technique based on the formation of a colored solution with UV-VIS absorbance proportional to frother concentration over a certain range has been developed. The calculation of concentration requires the comparison of the sample absorbance at a selected wavelength with a linear calibration (frother concentration vs. absorbance) constructed with values collected from solutions of known concentration (standards) at the same wavelength. It has been found that concentration ranges for preparation of standards can vary widely. An integration of our experiences into a databank can offer some guidance on the selection of standard concentrations. The databank includes results from the analysis of 37 chemical reagents, commercial frothers, and natural oils used in research work or at industrial sites. Grouping frothers by similar chemical structure or origin provides a good basis for selecting the standards to approach the maximum absorbance range for the spectrophotometer in use.INTRODUCTIONA technique to determine frother concentration on samples of industrial milling streams based on formation of a colored solution with UV-VIS absorbance proportional to frother concentration has been developed. The concentration is determined by comparison of its absorbance, at some selected wavelength, with those obtained by processing a series of solutions of known concentration (standards), at the same wavelength. It is desirable to have linear calibration (frother concentration vs. absorbance) over the widest concentration range. The upper concentration can be restricted by the instrument, as there is a maximum detectable absorbance (minimum transmittance), which can be reliably sensed by the UV-VIS detector (in most cases maximum absorbance is 3)."

Jan 1, 2016

The Australian Mineral Industry's growth in the last two decades is directly related to the skill and experience of its consultants in mining, metallurgy, geology, finance, management, marketing, and engineering. The role of mining consultants needs to be re-examined, so that the quality of the service they deliver will continue to be adequate for the 1990's. One means of this evaluation is by examining Case Studies in the strategies and difficulties of developing contract and entrepreneurial research.

Jan 1, 1986

By Andrzej Wieniewski, Cezary Regula, Bozena Skorupska, Krystian Cichy

"In this paper, experiences from Polish non-ferrous metals ores enrichment plants in the copper and blende concentrates quality improvement are discussed. The blende concentrate being produced in ZGH Boleslaw S.A., with Zn content of about 54,5% is characterized by the relatively high magnesium content reaching a level of 1% resulting from the dolomite presence, while for the zinc production by electrowinning a concentrate in which magnesium content should not exceed 0,3% is required. The implemented new technology for the quality improvement of blende concentrate is based on the leaching of zinc concentrate with sulfuric acid aimed at dissolving of the contained dolomite, and then flotation of the leached concentrate. It allows to obtain a concentrate with magnesium content below 0,1% at the simultaneously increased zinc content to about 57,5%. In the paper, laboratory tests results on the development of optimal flotation flowsheet for the gypsum removal and the industrial tests results concerning the process optimization of this flotation are discussed. In turn, the copper concentrate being produced in Polish copper ore enrichment plants KGHM PM S.A., is characterized by the increased organic carbon content - above 8%. It creates problems with the smelting of this concentrate because of difficulties with the heat removal derived from the combustion of organic carbon in the flash smelting process. The implementation of segregating flotation to the industrial practice allows the effective production of two concentrates with the differentiated chemical compositions - a concentrate with increased copper content and reduced organic carbon content for the flash smelting process, and a concentrate with lower copper content and increased organic carbon content for the shaft smelting process. In the paper, conditions of the segregating flotation and the achieved results are described."

Jan 1, 2014

By M. J. Allan

"The paper describes the author's experiences in the startup of autogenous and semiautogenous grinding circuits gained over the last twenty years on both large and small grinding circuits. Typical phases in commissioning from construction to startup with ore are covered. The paper also describes experiences with material handling systems, slurry pumping, vibrating screens, trommel screens and pebbles crushing systems. INTRODUCTIONThe commissioning of any new mineral processing plant is an important and exciting milestone in any project. It is at this point in time that the efforts of developers, design engineers, equipment suppliers and operators culminate in a finished product. The successful completion of any project requires that the plant achieve design throughput as quickly as possible. The success of any startup can generally be anticipated by the amount of careful planning which takes place before equipment is operated. The first part of this paper describes the steps in going from construction through to introduction of ore. The organization and planning of startup activities is also covered.The second part of this paper describes some typical problem areas and past experiences in the startup of semi-autogenous grinding circuits. Semi-autogenous grinding circuits present some special challenges in the startup phase. The description of some of these problems and experiences will hopefully provide other operators with suggestions on how to avoid (or at least prepare for) these problems."

Jan 1, 1992

By N. F. Dawson

Recovery of a chromite concentrate from UG2 flotation tailings streams, of a grade suitable for further pyrometallurgical treatment for the production of ferrochrome, has certain specific challenges not only by virtue of the decoupled nature of the primary PGM recovery process and secondary gravity based chromite recovery circuits, but also because of intrinsic variations in the nature of the ore and its mineral composition. Variability in the ore, together with upstream process dynamics, creates a challenging environment in which to achieve optimal recovery of a gravity concentrate with accurate grade control. This paper examines certain inter-relational aspects between the ore gangue and chromite mineral types, the influence of the primary PGM extraction circuit and secondary chromite extraction activity as applied specifically to UG2 ore against a background of actual plant experiences and circuit configurations applied in order achieve a suitable quality of chromite concentrate.

Jan 1, 2010

By Leland E. Paulson

The Grand Forks Energy Research Center and Commonwealth Edison of Chicago jointly conducted tests in which 400 tons each of subbituminous coal and lignite were dried in a commercial scale dryer, oil sprayed and cooled, then shipped in open-top rail cars from Pekin, IL to Grand Forks, ND and stockpiled. Cars containing raw coal and dried coal that had not been oil sprayed were also transported for comparative purposes. The tests were conducted in August and November of 1974. The subbituminous coal was dried from 26 to 16 pct moisture and the heating value was upgraded from 8,420 to 9,650 Btu/lb. The lignite was dried from 39 to 22 pct moisture and its heating value was increased from 6,420 to 8,300 Btu/lb. Before loading subbituminous coal was cooled to 115° F and sprayed with oil at a rate of from 2 to 6 gal/ton. Similarly, lignite was cooled to 85° F and oil sprayed at rates of from 1 to 2 gal/ton. Both shipments arrived in Grand Forks with a minimum of difficulty. The subbituminous coal was subjected to 2 inches of rain during transit with no change in average moisture content. The cars containing dried and oil treated coal had less material lost to wind than either cars containing raw or untreated dried coal. With both dried lignite and subbitnminous shipments, a moderate increase in temperature was measured during transit. With the subbituminous shipments, ignition occurred near poorly fitted bottom dump doors, but was limited to a very small area. The dried lignite was shipped when ambient temperatures were below freezing, and frozen coal was noted around the edge of the car. At Grand Forks, the coal was stockpiled using proven techniques and has remained stable to this date.

Jan 1, 1975

By C. Wegert, L. E. Paulson, S. A. Cooley, R. C. Ellman

The Grand Forks Energy Research Center (GFERC) and Commonwealth Edison of Chicago jointly conducted tests in which 400 tons of subbituminous and lignite coals were dried in a commercial scale dryer, oil sprayed and cooled, then shipped from Pekin, Ill., to Grand Forks, N.D., and stockpiled. Cars containing raw coal and dried coal which had not been sprayed, were also transported for comparative purposes. During transit, observations were made of changes in the coals' moisture content, dust losses, and temperature.

Jan 1, 1977

By Jose R. Hernandez-Aguilar, Chris J. Martin, Rob Thorpe

"This study presents an approach to establishing relationships between metallurgical performance and the characteristics of the bubble population (gas dispersion) inside flotation cells. Bubble size Db, superficial gas velocity Jg, and bubble surface area flux Sb (Sb = 6Jg/Db) measurements were obtained along with metallurgical samples in full-size equipment processing different ore types. The gas dispersion was manipulated by changing the operating conditions of the cells (gas flowrate and frother type) and the metallurgical performance (grade-recovery) was determined. In two cases, the Sb had a strong relationship with grade and recovery, hence, Sb could be used as practical operating parameter. In another case, Sb did not correlate with recovery. The reasons were attributed to creating small bubbles using frothers with desired anti-coalescence properties. This illustrated that bubble size was the key parameter for metallurgy rather than Sb.INTRODUCTIONUnravelling the mechanisms that govern the relationships between metallurgical performance and the characteristics of the bubble population (gas dispersion) inside a flotation cell remains a major challenge. Information on this subject is scarce in the literature, particularly, plant-scale data. The report of Jameson and Allum (1984) appears to be the first gas dispersion study conducted in industrial (mechanical) cells. To introduce concepts, some aspects of their work are reviewed here.The prime motivation of that study was to establish whether any particular cell design (among 44 cells surveyed) could produce very small bubbles (< 0.1 mm), which laboratory research suggested would increase the recovery of fine particles. Although one of the outcomes was that the (examined) cells did not seem to produce such small bubbles (Sauter mean1 D32 ˜ 0.9 mm), the analysis highlighted the importance of including other factors. Jameson and Allum indicated that, besides bubble size (Db), other characteristics of the bubble dispersion should be considered, namely: gas holdup ?g – the fraction of cell volume occupied by bubbles, superficial gas velocity Jg – is the gas flowrate divided by the cross-sectional area of the cell and, bubble surface area flux Sb – the rate of production of (new) bubble surface area (m2/s) per m2 of cell cross-sectional area. It should be noted that, whereas Jg, ?g and Db can be measured directly, the Sb is derived: Sb = 6Jg/Db, where Db is usually substituted by the Sauter mean diameter (D32)."

Jan 1, 2006

By D. V. Hughes, J. R. Nyberg

"Since 1985, a comprehensive automation system has been installed at the Outokumpu Oy Zinc Plant, Kokkola, Finland. In leaching and solution purification special sample handling equipment, on-line analyzers and instruments, and a computer-based control system with duplicated supervisory stations have been installed. The system has enabled closer control of the process and more efficient use of labor. Since its installation recovery of zinc has improved, and use of zinc dust, steam, and water have decreased. The system has performed reliably. It includes optimizing programs and process study tools, which facilitate improving process performance. An expert system has been built-up to prompt process personnel to take appropriate action on the basis of process data. In electrolysis a similar system, based on extensive monitoring of the process and of production of zinc cathodes, is used to maximize- current efficiency by maintaining optimum conditions in the process. It is planned that in the future the control systems will be integrated and extended to cover the roasting plant and effluent control.IntroductionThe Zinc PlantThe Zinc Plant of Outokumpu Oy Metallurgical Division at Kokkola, on the West Coast of Finland, has grown from a 90,000 t/a plant founded in 1969 to become, with its present capacity of 170,000 t/a, one of the world's ten largest zinc plants. Especially since the completion in 1988 of a thorough modernization programme, it is also among the world's most modern.The Kokkola plant takes its raw materials from Outokumpu's own mines, Vihanti and Pyhasalmi in Finland, and Tara in Ireland, and from outside sources. Concentrates are roasted in two Lurgi fluid-bed furnaces, and the calcine is leached and iron removed by the Conversion process. Following this copper, cobalt, and cadmium are removed, and zinc is refined by electrowinning. The leaching and purification, and the cell-house are automated under computer-based control, and anode and cathode handling in the cell-house are mechanized and fully automatic."

Jan 1, 1989

By Ingemar Hermansson, Thomas Bjerendal, Mattias Grävare, Carl-John Grävare

"AbstractHigh strain dynamic pile tests (HSDPT) on driven piles have been carried out on a routine basis in Sweden for more than 30 years. The Swedish Commission on Pile research established, in the early 1980s, safety factors based on the percentage of piles tested. The safety factors could then be reduced, creating economic incentives for the contractor to carry out testing.Energy formulas adopted by our neighbour countries, Norway and Denmark, were not accepted in Sweden as a reliable method since the dynamic testing method was considered to be a more scientific and reliable method. It has become almost the only in-situ method used to verify geotechnical bearing capacity on driven piles.The typical Swedish geology of soft soils overlaying very hard strata makes it possible to verify high design loads, typically 20 kN per cm2 of pile cross sectional area for steel piles and 1,5 kN per cm2 for concrete piles.Conventionally a certain percentage of the piles have been tested in Sweden. The EC7, on the other hand states a number of piles to be tested, regardless of the total number of piles. The Swedish NA (National Annex) states a maximum distance between tested piles, which results in better distribution of the test piles over the foundation.For shaft-bearing piles in soft clays, dynamic pile tests have to be correlated by static load tests.Historical backgroundOn a research basis stress-wave measurements have been carried out for a long time in Sweden. One example is a project in the city of Gothenburg, conducted by Fellenius and Pejrud (1964). Strain gauges were glued on the reinforcement bars in 60 m long, precast concrete piles at 3 m and 25 m above the pile tip respectively. Evaluation was done with different methods such as dynamic formulas,stress-wave measurements and in addition compared with static load tests.In the 1975 Building Code in Sweden, driving criteria for concrete piles based on stress-wave theory were introduced, as summarized in Table 1. The driving criteria are intended for 3 and 4 tonne gravity hammers. For hydraulic rigs, which have free-falling hammers, the drop height indicated should be reduced to 80 % of the values in the table. The criteria were considered to include a safety factor of 3,0. For 330 - 450 kN pile load, pile with a standard a cross sectional area of 235 mm x 235 mm was used. For 600 kN load, the standard cross sectional area was 275 mm x 275 mm."

Jan 1, 2014

By Guan Jichang

An abandened breakwater, located at the rear of No. 2 berth in Dongdu Port area of Xiamen City, was not cleaned thoroughly when the backfilling of sand started. The uncleaned stone layer was about 2 to 3 meters deep, with the average piece of stone weighing about 1 to 3 kN. A large grain storing house, 220X 60m2 in area, was designed and built at the above mentioned complicated site. The foundation of the grain house are made up of the cast-in-situ piles. It is well known that it is difficult for the submarine engineering drill to go down through such large-sized stones. Having com-pared the various plans, a final decision has been made which involves explosions with small amounts of charge plus cone bit in the enlarging of the size of the pores. Such a method has successfully prevented the pores from slumping and made it possible to fulfill the project without any difficulties. This paper also introduces the ways in effectively dealing with each individual stone.

Jan 1, 1991

By M. Tarvainen

"Lately, the development work in closed circuit grinding has mainly been focused on mills and on different types of instrumentation, mathematical models and automation in spite of the fact that the poor efficiency of the classifier is well known. It has also been proven by several investigations that by improving the sharpness of classifier separation, remarkable technical and economical advantages can be achieved. Some attempts to improve the performance of the most common classifier, hydrocyclone, have been made, among them injection of wash water above the spigot cyclone and retreatment of either or both of the products of the primary classifier. No method has been successful enough to achieve general adoption in the industry. The purpose of this paper is to introduce some industrial results achieved by two-stage classification where the coarse product of the turbulent-flow classifier, hydrocyclone, is cleaned in a laminar-flow cone classifier.The main target of the adoption of the two-stage classification circuit it naturally to improve the sharpness of size separation. This again leads to the following advantages in the grinding process:- lower circulating load and increased capacity- lower energy consumptionnarrower size distribution in the fine product- less overgrinding and less slimes- reduced specific surface areaThese improvements, no doubt, reflect on the subsequent concentrating process in the following aspects:the rate of flotation is improved, less reagents and energy is neededthe recovery and grade of valuable minerals in concentrates is improved- savings in dewatering can be expected- less fines in tailings improve the conditions for water recirculation."

Jan 1, 1980

By Guozhu Ye, Mikael Lindvall

"Swedish iron ore contains about 0.1 %V. The vanadium is reduced to the hot metal in a blast furnace and oxidised to the slag in a converter. The high V-content, up to 5 % V, leads to a very limited external application of the steel slag in Sweden. Since 2004, MISTRA - the Swedish Foundation for Strategic Environmental Research has together with the steel and mining industry in Sweden and Finland initiated and supported a long term project aiming at efficient recovery of vanadium in the slag, and at the same time a useful slag product with low V-content. The proposed concept consists of a reduction step and a phosphorus removal step. This paper will highlight some of the results with focus on the various metallurgical reactors used for slag reduction, including results from recently performed pilot trials using a DC furnace for cotreatment of metallurgical slags and other wastes.IntroductionToday, less than half of the produced LD-slag in Sweden is recycled to the blast furnace as a lime source and the rest is temporarily stored inside the steel plant. The steel slags cannot be used externally due to its content of vanadium and free lime. As the slag storage area is limited, this has become a problem for Swedish steel producers. The disposition of the slag is also a great waste of a valuable vanadium resource. The current potential value of vanadium in the discharged steel slag annually amounts to roughly US$ 100 million. Currently, Swerea MEFOS is conducting an 8-year vanadium recovery project called VILD (Vanadium in LD-slag) aiming at efficient recovery of vanadium and at the same time producing a useful slag product with low V-content. The project is financed by MISTRA - the Swedish Foundation for Strategic Environmental Research and the steel and mining industry in Sweden and Finland. Various reactors and process options have been tested in the past 7 years, from 3 kg laboratory scale, 150 kg induction furnace, 3 MVA pilot DC furnace, 5 MVA pilot AC furnace, 5 tons Kaldo furnace, to full scale direct hot slag reduction in the industrial site (12 tons of slag). This paper will introduce the VILD-concept and review the experiences gained from these trials. The advantages and disadvantages of the different options will be discussed and concluded."

Jan 1, 2012

By Olli Aulio, Outokumpu Oy

"GENERALThe Outokumpu Company is today an important European producer of metals from its own mines: copper nickel cobalt, ferro chrome and zinc being the main products. In 1972 about 4 million tons of ore was hoisted from eleven mines.Outokumpu Oy has gained experiences on the various aspects of on line computer control since 1968. This knowledge has been combined to develop a standard computer control package for concentrator control. Before the development of computer control package was started Outokumpu Oy had three large computer control systems. The first system was at the Pyhasalmi Concentrator, thee second at the LokkolaPlant, and the installation of the third system at the Vuonos Concentrator was just started.The characteristics of general computer software packages - both control and executive ones - were thus well-known as well as the practical usage of control theory. Furthermore Outokumpu had developed the Courier analyzer which included a so-called minicomputer. This project had given experience both 1n totally self made real tire executives and in computer hardware and peripheral d=vices. The instrumentation of the Outokumpu concentrators was designed and installed traditionally by the engineers of Outokumpu themselves."

Jan 1, 1973

By Damien Enright, Franz-Werner Gerressen

CFA/ACIP pile is the most used single pass drilling method for deep foundation installations. It is constructed by rotating and driving a Continuous Flight Auger (CFA) into the ground at a controlled speed to the specified pile depth. Concrete is then pumped under continuous positive pressure through the hollow stem of the auger to fill the borehole as the auger is withdrawn. CFA/ACIP piles are preferred due to their high daily production capacity when used in suitable soil conditions. CFA/ACIP piles have been installed in the United States for decades and the industry has seen a huge development in equipment, installation process, monitoring and more. Nowadays, CFA/ACIP piles are installed using fully computer monitored drill rigs rather than a bulky crane and lead setup. Because of the torque and crowd offered by these rigs, piles can be installed to depths of more than 100 feet and diameters up to 48 inches. New age crane-based equipment with leader systems are than welcome to substitute old fashioned bulky cranes These new age crane-based systems combine the benefits of sufficient hydraulic power, fully equipped software, etc. with the additional benefits that they can do single pass drilling without extension systems, even when drill depths of more than 100 feet are required. The paper will explain the construction process and will discuss some jobsite references and experiences made using the new age crane-based equipment.

Oct 1, 2022

By James J. Bean

Although determining and controlling specific gravity of operating medium in a heavy-media plant manually presents no problem, there are advantages to automatic recording and control. The two installations discussed employ the usual method of measurement. Pneumatic control with band control and reset features is used to regulate dilution water and hence specific gravity. Difficulties have been mechanical in nature and associated with obtaining a proper sample and maintaining tight air connections in bubble-tube piping.

Jan 3, 1950

By H. Wagner

During the last few years a large number of pillars in different mines were investigated. Pillar conditions were evaluated using subjective, empirical, geophysical and numerical methods. A critical comparison of the different methods showed some interesting coherence. This paper concentrates on experiences using the p-wave velocities as an indicator of pillar conditions. Während den letzten Jahren wurde eine große Anzahl von Bergfesten in verschiedenen Bergwerken auf ihren Zustand hin untersucht. Hierzu wurden subjektive, empirische, geophysikalische sowie numerische Methoden angewandt. Dieser Vortrag beschäftigt sich mit den Erfahrungen beim Einsatz der p-Wellengeschwindigkeit zur Beschreibung des Festenzustandes. Le condition géotechnique d’une grand nombre des piliers des mines souterraines différentes sont examinées ces dernières années. On a appliqué des méthodes subjectives, empiriques, géophysiques et numériques. Ce rapport occupe aux expériences avec l’application de la vélocité des ondes de compression pour tracer le condition des piliers.

Jan 1, 2003

By Patrik Ericsson

During the 90?s Atlas Copco and LKAB developed a pioneering fully automatic long hole production drilling system based on the Atlas Copco Simba W469 drill rigs. These drill rigs have since then drilled about 8.000.000 drill meters at the LKAB Kiruna and Malmberget mines. In 2005 LKAB ordered three new Atlas Copco Simba W6 C, to complement Simba W469s still in operation. These new Simbas are based on the latest generation computerized drilling technology have proven to meet the expectations of LKAB and now form a base for future automation in Kiruna and Malmberget mines. This paper will present experiences from the introduction of Simba W6 C in LKAB Kiruna and Malmberget mines. The paper will also elaborate on the latest developments in remote access and remote control technology making it a common automation option available for all computerized Atlas Copco drill rigs.

May 1, 2007

By William Van Impe

A most renewing and promissing soil displacement screw pile is called the O-pile. The O-screw pile is a soil displacement auger pile based on a screwing in - screwing out procedure. The displacement auger head consists of a discontinuously diameter - increasing steel tip, on top of which the continuous screw flange with variable pitch is mounted. The soil displacement is kinematically ensured by downwardly oriented slots mounted on the auger head at different well chosen locations on the flanges. This leads to a very efficient lower energy screwing-in sequence of the pile and consequently to a high penetration rate. A test loading program of instrumented O-piles has been carried out in order to evaluate the load settlement behaviour, the shaft and tip capacity of the O-pile, including its specific installation parameters.

Jan 1, 1996