Search Documents

By James A. Finch, Xiang Zhou, Yue Hua Tan

Widely used as collectors for nonsulfides, amines also show some frothing properties. Evaluating frother functions of amines and their combination with conventional frothers addresses whether one reagent delivering both collector and frother functions compromises the efficacy of either. From the findings, whether blending with frother confers any benefit requires knowledge of the residual amine concentration. If it is below about 10 ppm, blending eliminated coalescence, but there appears to be no benefit if the concentration is above 15 ppm.

By James A. Finch, Xiang Zhou, Yue Hua Tan

Methods to determine frother functions, control of bubble size and froth properties, are now widely used. Some collectors also exhibit frother functions which are less understood. Using a water-air system in a mini-mechanical flotation cell setup, this paper determines bubble size and water overflow rate for three amine collectors: one primary amine (dodecylamine, DDA) and two commercial ether amines (Flotigam® EDA and Flotigam® 2835-2L) and their combination with two common frothers, MIBC (methyl isobutyl carbinol) and PPG 425 (polypropylene glycol, molecule weight 425). Compared to the frothers, the amines were less effective in reducing bubble size, giving larger minimum size and the two commercial amines showed evidence of coalescence at low concentration. In blends, at fixed frother dosage, frother eliminated the coalescence but as amine concentration increased the amines dominated bubble size. Water overflow was a strong function of reagent type. For fixed 1-cm froth depth, PPG 425, Flotigam® 2835-2L and to a lesser extent DDA produced overflow while MIBC and Flotigam® EDA did not. In blends with frother overflow increased except with Flotigam® EDA. Mechanisms are briefly explored. The principal benefit of blending identified is the elimination of coalescence if residual concentration of the two commercial amines is below ca. 10 ppm.

By W. L. Freyberger, R. B. Booth

Froth flotation is a chemically induced method for beneficiating or up- grading an ore, which utilizes a layer or column of froth as a separating medium to segregate and remove the valuable minerals from the worthless gangue components of a finely ground ore suspended in water. The object of this chapter is to discuss the theoretical aspects of froth formation, the various frothing agents employed in flotation, and the effect of chemical structure on froth formation, and to correlate these factors with flotation technology. The flotation method of separation is conducted in three main steps: 1) selective chemical modification of the surface of specific mineral particles to effect floatability or nonfloatability; 2) contact between air bubbles and mineral particles, the selective adherence of floatable minerals to these bubbles, and the rejection of nonfloatable minerals; and 3) separation of the floatable minerals from the nonfloatable minerals. As indicated above, these three operations are achieved by the use of chemicals. Frothers play their most important role in the second and third steps by influencing particle- bubble contact and by affecting the degree of separation obtained in the froth column. Frothers, as defined by flotation operators, are compounds that are used specifically for the purpose of creating a froth in a flotation separation. How- ever, some collectors produce froths that are adequate for some flotation operations. Although this chapter is chiefly concerned with the specific frothers used in flotation, some discussion of frothing collectors is included. Otherwise, collectors (or promoters) and modifiersare not discussed at length; for information on these types of flotation chemicals, the reader is referred to other sections of this book or to other sources.l HISTORICAL DEVELOPMENT OF FROTHING AGENTS Historically, there are two distinct phases in the development of frothing agents and other flotation chemicals: 1) 1860 to 1920-oil flotation, and 1921 to date-chemical flotati0n.2~3 Early in the first period, large quantities of fatty and oily materials, up to 10 to 20% of the weight of the ore, were used as a means of separating the sulfide and oxide components from the gangue minerals in ore pulps. Later, various gases replaced these large quantities of oil as a buoyant and separating medium, decreasing oil requirements to less than 1% of the weight of the ore. With this reduction in oil

Jan 1, 1962

By K. Rushdi, B. E. Abulnaga

The conventional Froude number is blind to the presence of solids, their density and their concentration in a stream of slurry mixture such as tailings flowing in an open channel. This often leads to rough approximations of subcritical, critical and supercritical regimes, based on one phase flow Froude number, limiting subcritical to a value smaller than 0.8 and supercritical to values above 1.4, as proposed in the past by Green, Abulnaga and other authors. While acceptable for small flows, such approximations can be uneconomical for the larger flows encountered in some modern plants that treat up to half a million t/day. A review of concepts of a densimetric Froude number sheds some light on the effect of solids on stratification prior and subsequent to a hydraulic jump. While the approach is heavily borrowed from modern sedimentology, it provides a useful tool to designers of large launders or open channel tailings systems. These concepts are reviewed with some practical examples.

Jan 1, 2013

By Daniel L. Cluff

The Canadian mining industry needs to find viable alternatives to the conventional cemented pastefill/hydraulic methods of backfilling open stopes for underground mines located within a permafrost zone. The harsh environment and the isolated location of a mine north of 60° impose additional challenges to standard backfill methods and opportunities to the technological and operational issues related to the use of frozen fill. Underground open stoping mining methods require the placement of fill material to enable the controlled recovery of ore from secondary and tertiary stopes. The typical design of the fill material requires the specification of inert material, water and binder. The permafrost conditions provide the additional parameter of subzero temperatures for backfill design and process control. The paper presents the results of an experimental field study, using large size samples, to determine the strength capacity of frozen backfill. The experimental work was performed utilizing rockfill and tailings material with moisture content consisting of water and ice crystals. Preliminary results indicate that the mixture of rockfill, tailings and moisture, develops strength that meet the demanded requirements for open stoping. A thermal equilibrium modelling analysis is presented in the paper.

May 1, 2008

By Daniel Cluff

Frozen backfill for mining operations in permafrost must be delivered in such a state so as not to thermally impose on the host rock surrounding the filled stope. The placement process, the material strength demand, and the freezing time delay are the parameters that control the applicability of the method. A two-year research program was carried out in the field and using a laboratory-scale apparatus, designed to simulate a pour of frozen backfill, to study the mixing, thermal properties and segregation. The frozen rock and tailings must be at a below zero temperature and get fully wetted so the surfaces cause adherence of the particles to one another and enhance the solidification of the poured backfill. The results provided a recipe and a process for mix design for open stoping operations in cold regions. The testing evaluated the sensitivity of the test parameters that included the amount of water added in the mix, the temperare of water, the rockfill/tailings ratio, and the temperature of solid constituents.The paper presents the result of this environmentally friendly, innovative technology. The distribution of the materials and the mixing process are instrumental in achieving the properties required for open stoping applications.

Oct 1, 2010

By Derek J. Cyr

Climate has an immense impact on the properties of Athabasca oil sands and the ease or difficulty with which it is excavated and extracted. During the winter months, exposed oil sands surfaces freeze. When hydraulic and electric shovels used in the various operations in the Fort McMurray area excavate the benches, large frozen lumps are created. These lumps are either destined for a lump dump where increased costs are incurred due to rehandle, or they are sent to the primary crushers where they can cause significant downtimes by jamming the crusher. The crusher down time can sometimes be in the order of hours of lost production. Studies on data from two consecutive winters at Syncrude Canada?s North Mine show a high correlation between climate and the generation of frozen oil sands lumps. Temperature, ground cover, traffic, bench exposure time, oil sands grade and moisture content all contribute to this problem. A 1D frost penetration model was used to predict the depth of frost expected in oil sands and the corresponding likelihood of frozen oil sands lumps. To combat the challenge of frozen lump generation, a number of proactive and reactive measures can be taken: artificial snow, shallow ponds, scheduling, blasting or ripping.

May 1, 2004

By Abolfazl Eslami, Masoud Zare, Ali Asadi, Ali Abrang

"Physical small scale models for study of deep foundations can be performed in simple chambers (1g), calibration chambers (CC), and centrifuge apparatus (ng) which involve some limitations and difficulties. In recent years, Frustum confining vessels (FCV) have been developed for physical modeling of deep foundations. This device is frustum of a cone shape that applies a steady pressure on its bottom and creates a linear stress distribution along its vertical central line. A new FCV which has been built in AUT is introduced. This device has a height of 1200 mm, top and bottom diameters of 300 and 1300 mm, respectively. Through the application of bottom pressure up to 300 kPa, the insitu overburden stress conditions equivalent up to 40 m soil deposits consistent to the embedment depth of commonly used piles. Observation indicated that there is approximately a linear trend of stress distribution, and this device can create realistic overburden stress in the desired control volume along the central line. Moreover, a couple of compressive and tensile load tests were performed on steel tubular open end model piles driven in sand with length of 750 mm and different diameters and L/D ratio between 8-15. Comparison of load capacity between tested and full scale piles demonstrate a suitable conformity for similar confinement conditions. Therefore, the FCV can be realized as an appropriate apparatus for investigation of piling geotechnical behavior and examination of construction effects.IntroductionDeep foundations are designed as foundation system for supporting heavy loads, high rise and important structures. Different theoretical, numerical and experimental approaches have been developed to study the geotechnical behavior of deep foundations. Experimental methods are employed to clarify directly pile-soil interaction and because of repeatability, analogy, rapid measurement and cost efficiency, physical modeling can be realized as an intermediate technique compared to element testing and full scale load tests."

Jan 1, 2015

By C. A. Young

Previous experimental results have shown that an increase in temperature and/or oxygen concentration leads to an increase in the hydrophobicity of fluorite (CaF2) with adsorbed oleate. Subsequently, ex-situ Fourier transform infrared (FT-IR) transmission studies suggested that this increase in hydrophobicity was the result of double-bond reactions between adjacent oleate species adsorbed at the fluorite surface. Now an in-situ FT-IR study on single crystals of fluorite has been used to monitor this phenomenon using internal reflection spectroscopy (IRS) with the crystals serving as reactive internal reflection elements. The double-bond reaction has been correlated with in-situ adsorption density measurements. These results demonstrate that only the first chemisorbed oleate layer undergoes the double-bond reaction at an appreciable rate. However, multilayers of precipitated calcium oleate in the case of fluorite appear to react minimally even for oxygen saturated solutions at elevated temperatures.

Jan 1, 1991

By F. G. Hyde

Passage of the Public Utilities Regulatory Policy Act ("PURPA") in I 978 created an entirely new industry that is referred to today as the Independent Power Producers ("IPP"). Requirements of project owners, environmental compliance, project design, the financial community and most of all, the need to be a low-cost producer presented a unique situation for the sourcing and the utilization of fuels. Depending on the specific type of project being developed, (e.g. coal-fired, wood/biomass, natural gas, petroleum coke or a blend of several fuel types) and the type of boiler design, it is important to acquire fuels that will optimize both the project's operating efficiency and flexibility. This paper will focus on the acquisition of fuel for coal-fired projects, but will describe the necessary steps in the sourcing, contracting for, and the utilization of fuels and transportation resources in the IPP industry today.

Jan 1, 1996

The influence of fuel additives on automobile exhaust emissions was studied using engines currently found in the U.S. vehicle population. The fuel additives used in the experiment were four multifunctional additives and one lead antiknock additive. Experimental work was done to determine both the direct effect of the additive per se on exhaust emissions and the influence of Long-term additive effects on emissions with mileage accumulation. Results showed no significant direct or intermediate effect on exhaust emissions for any additives tested. In subsequent experimental work concerned with the long-term or indirect effects of additives, the detergent-dispersant additives were found to have little influence on emissions when used in conjunction with high-quality oil and motor fuel. The lead (tetraethyl) antiknock additive increased exhaust hydrocarbons approximately 12 to 17 percent during a 4,000-mile accumulation period using a base fuel containing 2 ml of tetraethyl lead per gallon. An unleaded fuel was used during a similar accumulation period with no significant increase in exhaust hydrocarbons with mileage.

Jan 1, 1971

The National Institute of Occupational Safety and Health has classified diesel exhaust as a potential human carcinogen. Though standards for diesel particulate matter (DPM) in the work place have not been established, concern for the health of miners is prompting mine operators to consider methods for reducing worker exposure to diesel exhaust. Approach One of many methods for reducing DPM being investigated by the Bureau of Mines is the use of additives in diesel fuel to improve combustion. Research Results Three fuel additives have been tested in Caterpillar and Deutz diesel engines which are similar to types used in underground mines. One iron-based additive containing ferrous picrate had no effect on emissions. A second iron-based additive containing ferrocene reduced DPM between 5 and 45 pet depending on engine operating conditions. The 37-pct reduction for an 8-minute duty cycle, which includes a wide range of transient loads and speeds, is considered to represent in-mine performance.

Jan 1, 1990

By Frank C. Stevens

The availability, cost and use of fuel and electricity for the cement industry is difficult to predict with a great degree of accuracy because the historical pattern of factors affecting energy was disrupted during the years 1972, 1973 and 1974. Forecasting is both an art and science and is based on .the premise that the best indicator of the future is the past. Statistical data is used to guide economists and businessmen in their predictions of the future. Even though the energy picture is changing, it is believed that electricity and fuel will be available for the cement industry in the foreseeable future, and this energy will be more costly in relation to the other items that are part of the manufacturing costs for portland cement.

Jan 1, 1977

By Robert Schorr

A Discussion of the Paper by Robert Schorr, read at the Atlantic City meeting, February, 1904. (Washington Meeting, May, 1905.) E. T. DUMBLE, Houston, Texas (communication to the Secretary*) :-In addition to the list of publications mentioned by Mr. Schorr and those by Prof. Hofman, I call attention to the following references : Studi sulle Lignite, by Capacci. Turin (1890). (An excellent work.) Report of Brown Coal Industry in Germany. J. Cosmo Newberry. Department of Mines, Victoria (1892). Second Report of the Royal Commission. on Coal Supply. Vol. II. London (1904). Peat Fuel: Its Manufacture and Use. Report of the Bureau of Mines of Ontario, 1903. Mr. Schorr says : " Brown coal and peat are briquetted as a rule without binder," but this statement is entirely true only so far as raw peat is concerned, and it is but partly true of brown coal. With regard to raw peat, briquetting without bond is carried on successfully both in Europe and America, and the development of the industry in Canada is fully described in the Bureau of Mines report for 1903, mentioned above. While there is still room for improvement in the efficiency of some of the arrangements for drying the peat previous to briquetting, a very satisfactory fuel is made at a price which enables it to compete with coal. During the late strike in the anthracite regions of Pennsylvania, the manufacture of peat: briquettes received a considerable impetus, and possibly the attention directed to it on this account may result in a. considerable increase in the output. In Canada. the peat when it is first excavated from the ground

Mar 1, 1905

By Fred C. Delabbio

The successful implementation of a new technology in an underground production mine requires many challenges to be overcome. These challenges include mine hardening of new technology, mitigation of safety risks and hazards, mine operation support, and technology transfer to mine staff. In the end, the majority of these challenges relate to the human aspects of implementation. The approach selected to overcome these challenges must be customized and appropriate for each unique situation. This paper outlines the approach used to address these challenges as part of successful implementation and resulting demonstration of the hydrogen fuel cell locomotive at the Placer Dome (CLA) Limited, Campbell Mine. This technology demonstration at Campbell Mine is critical for determining technical, regulatory and implementation aspects to be incorporated into future fuel cell prototypes such as the LHD project.

May 1, 2003

By T. MacKinnon, M. C. Bétournay, D. Eastick, F. C. Delabbio, C. Graves

"The successful implementation of a new technology in an underground production mine requires many challenges to be overcome. These challenges include mine hardening of new technology, mitigation of safety risks and hazards, mine operation support, and technology transfer to mine staff. In the end, the majority of these challenges relate to the human aspects of implementation. The approach selected to overcome these challenges must be customized and appropriate for each unique situation.This paper outlines the approach used to address these challenges as part of successful implementation and resulting demonstration of the hydrogen fuel cell locomotive at the Placer Dome (CLA) Limited Campbell Mine. This technology demonstration at Campbell Mine is critical for determining technical, regulatory, and implementation aspects to be incorporated into future fuel cell prototypes such as the LHD project."

Jan 1, 2005

By A. R. Miller

A fuel cell locomotive incorporates the advantages of its competitors, namely catenary-electric and diesel-electric units, while avoiding their disadvantages. It possesses the environmental benefits, at the vehicle, of an electric locomotive but the higher overall energy efficiency and lower infrastructure costs of a diesel locomotive. The natural fuel for a fuel cell is hydrogen, which can be produced from many renewable sources or via nuclear energy, and thus a hydrogen-fuel cell locomotive will not depend on imported oil. Hydrogen produced from renewable primary energies or nuclear energy would provide a totally zero-emissions vehicle, that is, with zero carbon in the energy cycle. A project partnership among Vehicle Projects Inc of the USA, and South African partners Anglo American Platinum, Ltd, Trident South Africa, and Battery Electric, has designed and is launching a series of five prototype fuel cell-powered mine locomotives.

Jan 1, 2012

By M. C. Bétournay

Under the requirement to define the economic advantages of using hydrogen fuel cell vehicles, a broad-scoped project was initiated to quantify the costs associated with operating fuel cell vehicles and diesel vehicles. While ventilation savings are clearly an advantage for the former, a complete and detailed analysis of this and other operational and capital cost elements was undertaken in order to provide the mining industry with factual information in considering the changeover from one technology to another. This paper outlines the results of the investigations to date defining the costs/benefits associated with capital purchases, operations (electrical/diesel, mine air heating fuel, ventilation, openings, surface and underground infrastructure, maintenance, labour, etc.), delivery of energy, regulatory obligations, and mine production. Considerations are given to the type and size of a mining operation, the depth, and location in North America. Significant ventilation power, equipment, and infrastructure savings are possible with the application of fuel cells for shallower mine applications. At depth, where heat is an issue, there is a reduction in benefit. Specific qualifiers such as minimum air velocities, dust dilution, shaft, and heating system velocity limits must be considered on an individual mine basis. While the capital cost for fuel cell mining equipment is currently higher than diesel versions, the high cost of fuel cells is anticipated to be reduced significantly in the near future with the intensification of manufacturing. In either case, the operational savings would probably be sufficient to balance the supplementary capitalization costs. Comprehensive reports have been issued.

May 1, 2005

By G. Righettini, G. Desrivières, P. Mousset-Jones, R. Lacroix, M. C. Bétournay, P. Laliberté, S. Hardcastle

"Under the requirement to define the economic advantages of using hydrogen fuel cell vehicles, a broad-scoped project was initiated to quantify the costs associated with operating fuel cell vehicles and diesel vehicles. While ventilation savings are clearly an advantage for the former, a complete and detailed analysis of this and other operational and capital cost elements was undertaken in order to provide the mining industry with factual information in considering the changeover from one technology to another.This paper outlines the results of the investigations to date defining the costs/benefits associated with capital purchases, operations (electrical/diesel, mine air heating fuel, ventilation, openings, surface and underground infrastructure, maintenance, labour, etc.), delivery of energy, regulatory obligations, and mine production. Considerations are given to the type and size of a mining operation, the depth, and location in North America.Significant ventilation power, equipment, and infrastructure savings are possible with the application of fuel cells for shallower mine applications. At depth, where heat is an issue, there is a reduction in benefit. Specific qualifiers such as minimum air velocities, dust dilution, shaft, and heating system velocity limits must be considered on an individual mine basis. While the capital cost for fuel cell mining equipment is currently higher than diesel versions the high cost of fuel cells is anticipated to be reduced significantly in the near future with the intensification of manufacturing. In either case, the operational savings would probably be sufficient to balance the supplementary capitalization costs.Comprehensive reports have been issued."

Jan 1, 2005

By Nagai K, Moriyama K

Toyo smelter has been making s veral efforts to reduce and diversify energy for dealing successfully with such :n:;rgy problems as the first and second oil crises. ::,specially it is one of th:; most important subjects to substitute oil by alternative: energy source, because oil is expensive and unstable with respect to its supply. t _'hercfore i was decided to propel tnC ezhstitution of coal *jr oil. in the first place, the supple- mental fuel oil in the reaction shaft was replaced by oil to coal in 1981, and then th, fuel substitution of pulverized coal was achieved in the steam superheater in 1984. 3y these fuel substitutions about 7u,' of the total fuel energy at 2oyo smelter has been replaced by coal. in this paper the fuel substitu- tions at loyo smelter are described in detail.

Jan 1, 1987