Search Documents

By Robert M. Lewis

Can wet-ground mica be produced from mica schist ores, and if so, would its properties be comparable with products now on the market? This was the problem which prompted the development of a flowsheet for the beneficiation of mica schist. The fine-ground mica industry relies on weathered pegmatites and alaskite ores as sources of raw material. The mica concentrates obtained from these ores are relatively clean and require moderate beneficiation to meet color and bulk-density specifications. Mica obtained from mica schist is iron-stained and decrepitated and requires additional beneficiation to produce a wet-ground mica product. Despite these adversities, there are several advantages to be gained by mining and processing mica schist ores. The mica content of these ores is considerably higher than that of the pegmatites and alaskite ores now being mined, often containing in excess of 40% mica. This higher-grade mica feed should promote a lower mining and milling cost. The mica schist ores with their higher mica content would mean less tailings to handle; however, there would have to be a means for disposing of acid and sulfate wastes. A flowsheet was developed whereby mica could be recovered from mica schist ores and beneficiated in a way that would result in a high-quality end product.' The essential phase of the process involves using reducing reagents to increase the magnetic susceptibility of iron contaminants which then can be removed with a magnetic separator. General Treatment Procedure The mica is floated by either of two methods, an amine float in an acid circuit' or the U.S. Bureau of Mines (USBM) amine-fatty acid float in an alkaline circuit' The flotation mica is ground in a pebble mill to liberate contaminated particles and expose iron-stained surfaces. The concentrate is then conditioned with a reducing reagent and passed through a Frantz Ferrofilter for the removal of magnetic material. The nonmagnetic product is acid-leached to further reduce the iron contamination. The leached material is then ground to product size and checked for specifications. Discussion of Flowsheet and Its Development Flotation: The mica is concentrated by flotation using either of two methods: an amine float in an acid circuit, or the USBM amine-fatty acid float in an alkaline circuit.' The writer does not wish to elaborate on the relative merits of the two flotation procedures; however, after investigating ores from various localities, it was felt that the amine float in an acid circuit was more consistent when using a standard procedure. Iron Reduction and Magnetic Separation: This phase of the flowsheet may be considered the key to the process. It was developed when it became apparent that hot acid leaching had just about reached its maximum effective¬ness for color improvement. S. C. Sun and William Hirsh in "Hydrochloric Acid Leaching of Iron From Pennsylvania Aluminous Clays,"` reported iron extraction for -20-mesh minerals of 82.20% for hematite and only 33.46% for magnetite. The test procedure employs a 19% hydrochloric acid solution, 104°C temperature, and 10% solids. It was felt that magnetic removal of some of the iron contaminants before leaching therefore would be advantageous. Since the iron minerals present as contaminants vary in magnetic susceptibility, it was decided to experiment with reducing reagents as a means of influencing their magnetic properties. Zinc hydrosulfite or sodium hydrosulfite were the reagents used throughout the tests. The procedure developed consists of conditioning the mica concentrate in a closed container at approximately 5% solids with a reducing reagent. Approximately 10.0 lb of zinc hydrosulfite per ton of mica concentrate is used. The ferric iron is reduced to the ferrous state (magnetic) and oxidation is retarded by isolation from the atmosphere in a closed container. After the desired conditioning time has elapsed, the material is passed through a Frantz Ferrofilter where the magnetic particles are retained and discarded as

Jan 1, 1972

By Isobel Yeo, Luca Cocchi, Sven Petersen, Nico Augustin, Sean Plunkett, Ingo Klaucke

Exploration for seafloor massive sulfides is currently mainly focused on investigation for active hydrothermal vent fields. However, most of the resource potential is thought to be related to inactive, large deposits that had enough time to accumulate sufficient tonnage. At the same time, ageing of these deposits will ultimately result also in burial acted by either sediments and/or volcanic deposits. We currently lack the technologies to explore for these deposits in a time- and cost-efficient manner. In the fall of 2012 we used a number of AUV-based technologies to explore and image a sulfide occurrence at the Palinuro Volcanic Complex in the Tyrrhenian Sea (Mediterranean Sea; Fig. 1) where sampling and drilling have documented a buried polymetallic barite-pyrite dominated site (Petersen et al., 2014). Sulfide mineralization is here covered by volcaniclastic and pelagic sediments and only red sediment staining and the presence of few tubeworm bushes indicated recent hydrothermal activity - black smoker venting is absent. We used AUVbased high-resolution bathymetry, sidescan sonar imaging, subbottom profiling, as well as magnetics to describe, in a quantitative way, the previously known sulfide-bearing areas as well as to successfully explore for new hydrothermal sites including large chimney structures (Figs. 2). Additionally chemical sensors (CTD, Eh, turbidity) investigated the water column for signs of hydrothermal activity in areas not previously investigated, but at the end, only weak anomalies were found in the southern part of the summit.

Sep 1, 2014

By R M. Hough, G Duclaux, M A. Pearce, M F. Gazley

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Microcharacterisation, such as that described in this paper, provides understanding of a mineral system at multiple scales, and understanding microscale variations is the key to understanding the large-scale variations in a mineral system. More than 50 high-grade lode samples from across Plutonic Gold Mine (Plutonic), Marymia Inlier, Western Australia were analysed by a variety of techniques, including micro X-ray fluorescence (µXRF) mapping, micro X-ray computed tomography (µCT), scanning electron microscopy (SEM), field emission gun SEM, electron back-scatter detector (EBSD), proton-induced X-ray emission microprobe and synchrotron XRF mapping. These data demonstrate that competency contrasts are the key to governing the location of Au mineralisation at Plutonic. Micro CT imaging of high-grade samples shows the Au filling in voids and pore-space in the rock, after having travelled along more permeable layers and already existing or reaction-induced pores formed during hydrothermal circulation. Using 3D visualisation, the Au is seen to form a connected network that appears undisturbed at the scale of the samples, and a high-grade Au deposition event was one of the last events to affect the rock. This interpretation is supported by SEM analyses on high-grade samples that reveal calc-silicate (epidote-clinozoisite) alteration that is not present in lower Au grade samples, which are typically dominated by potassic alteration, and that sulfides are typically less abundant close to the Au. The replacement of biotite by chlorite is an alteration associated with the high-grade Au-mineralising fluid. Gold is coarsest where Au particles are located on the margins of minerals, typically sulfide and quartz grains, suggesting the importance of rheological contrast at the microscale. Furthermore, EBSD data reveals that Au is undeformed and overprints peak metamorphic and retrograde minerals. Data confirm recent deposit-scale observations, suggesting that deposition of high-grade, visible Au was related to a hydrothermal fluid circulation event late in the geological history of Plutonic.CITATION:Gazley, M F, Duclaux, G, Fisher, L A, Hough, R M and Pearce, M A, 2015. High-resolution characterisation of gold mineralisation at Plutonic Gold Mine, Western Australia – evidence for the late-stage deposition of high-grade gold , in Proceedings PACRIM 2015 Congress, pp 51–58 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By R. Howard

"In projects involving resource development and plant optimization, the use of in-mine geophysics can deliver considerable benefit. The value proposition lies in using very high resolution downhole measurements to model process-plant outcomes. The calibration procedure used to convert in-situ physical properties into process engineering parameters is illustrated using two iron ore projects. Data correction was related either to orebody structure or mineral formation. The deliverable from this approach is a series of high-definition sections indicating the variability of ore delivered to a front-end separation plant and parameters for mine scheduling and stockpile design needed for maximum product yield.RÉSUMÉ Dans des projets de développement des ressources et d’optimisation de l’usine, l’utilisation de la géophysique minière peut engendrer des bénéfices considérables. La valeur de la proposition réside dans l’utilisation de diagraphies à très haute résolution afin de modéliser les résultats de l’usine de traitement. La procédure d’étalonnage utilisée pour convertir les propriétés physiques in situ en des paramètres d’ingénierie de procédés est illustrée en se basant sur deux projets de minerai de fer. La correction des données porte sur la structure de la masse minérale ou de la formation minérale. Les livrable attendus de cette approche sont une série de sections à haute définition, signalant la variabilité du minerai livré à une usine de séparation de première ligne, des paramètres pour l’échéancier de la mine et la conception des haldes requis pour une production optimale."

Jan 1, 2016

By C M. Côte, P Bolz, R Chrystal

The design of final landforms is an integral part of mine closure plans in Queensland and aims to ensure the rehabilitated land is safe, stable and non-polluting. Landform stability in this context is commonly assessed using Landscape Evolutions Models (LEM) which are physical models simulating sediment erosion and deposition around individual landforms over long timespans (up to thousands of years). The most used LEM for assessment of rehabilitated landforms in Queensland is SIBERIA (Willgoose, Bras and Rodriguez-Iturbe, 1991; Tucker and Hancock, 2010). SIBERIA models are complex, require very detailed input data and simulate erosion and deposition over time frames that extend decades beyond closure. They are not suitable to assess erosion risks during the operational phase of a mine and to support the development of erosion and sediment control plans. Other types of erosion models, such as the Revised Universal Soil Loss Equation (RUSLE, Wischmeier and Smith, 1978) or Water Erosion Prediction Project (WEPP, Nearing et al, 1989) calculate soil loss on a monthly or yearly basis and are much better suited to erosion management during the operational phase. They are simpler to implement and can support the design of control measures. For instance, designing a sediment basin requires quantification of sediment loads, which can be produced by these models. In Queensland, the legislation around sediment and erosion control for open cut mines is currently tightening. Soil erosion remains a major concern due to potential impacts on the receiving environment. It requires management during operation and for closure consideration alike and it is critical that erosion and sediment control plans are developed with the most appropriate tools. Globally, RUSLE is the most widely used soil loss model (Borrelli et al, 2021). This is because it is an empirical model with relatively simple input requirements: biophysical data such as soil properties, vegetation cover, topography and rainfall variability, which can be directly measured or derived from regional or national databases and/or spatial data sets that are available in most parts of the world. The second most used model is WEPP (Borrelli et al, 2021) but compared to RUSLE, there is a large drop in the frequency of its use. This is because WEPP is physically-based and has more complex data requirements. WEPP integrates hydrology, hydraulics, erosion mechanics and land cover to predict soil erosion and sediment transport on hill slope profiles and small watersheds (Stolpe, 2005). It requires some biophysical parameters in formats different from those of RUSLE, as well as detailed hydrologic and catchment data. Nevertheless, it has been used in landform design for mines across Australia to determine final landform stability (eg Howard and Roddy, 2012; Costin, 2020). In this study, we assess which tool would be the most appropriate to support development of erosion and sediment control plans from operation to closure. We use RUSLE and WEPP to predict soil loss from a mine site, compare the results from both models and outline the advantages of each method.

Aug 2, 2023

By C. Melvin Lepper

High-resolution shallow seismic reflection methods are being used by the Bureau of Mines to map underground geologic features in coal mines. These features include faults, channel sand, washouts, rolls, and steep dips. The seismic method is proving useful for locating all of these at reasonable cost and with better definition than available with drill programs alone. This report provides a capsule description of the techniques and their application to mine planning.

Jan 1, 1976

By A. R. Wagner, E. Berkman

The use of high-resolution seismic surveys in coal exploration and mine development is becoming established as a standard technique in the industry. Their most significant contribution is in the effectiveness of reducing the number of core holes needed to understand the complex geological nature of coal by identifying geologic faults and mapping coal seam continuity and relative coal thickness. With these goals in mind, a high-resolution seismic survey was conducted in 1980 in the Wasatch Plateau coalfield of Utah. As a result of the success of this initial survey, numerous additional surveys have been performed over the past six years.. The interpretations of these subsequent surveys have led to the location of faults, fluvial channel sandstones, and coal thickness trends. This paper presents a review of high-resolution seismic technology as applied to coal exploration followed by three case histories, two of which illustrate the utility of the technique related to coal thickness determination and faulting and one that serves as an example of pitfalls in interpretation.

Jan 1, 1987

By Sven Petersen

In April 2010 three REMUS6000 series autonomous underwater vehicles (AUVs) have been used to simultaneously map large areas near the Mid-Atlantic Ridge (3°N) axis in water depths ranging from 1,000m to 4,000m. One vehicle was provided by the Leibniz-Institute for Marine Science, IFM-GEOMAR (Kiel, Germany) the other two were provided by the Waitt Institute for Discovery (La Jolla, USA) and managed by the Woods Hole Oceanographic Institute (USA). The REMUS6000 vehicles, manufactured by Hydroid Inc. (USA), are "cigar-shaped" vehicles (4m long and weighing approx. 900kg) and consist of a tapered forward section, a cylindrical midsection and a tapered tail section. An internal titanium strongback, which extends through much of the vehicle length, provides the structural integrity and acts as a mounting platform for syntactic foam, equipment housings, various sensors and release mechanisms. The AUVs can be used in various payload configurations such as multibeam bathymetry, electronic still camera, or subbottom profiler. For these missions the electronic still camera configurations was installed. An EDGETECH 2200M dual frequency (120/410 kHz) side scan sonar was used to map the seafloor, but other frequencies are readily available for more options in resolution and range. The 120 kHz side scan transmitter was used for most missions in order to map large areas (increased range) and to be able to fly at higher altitudes (between 70m and 90m) above the rough seabed encountered in this area. The maximum slant range was between 600m and 700m on both sides resulting in a swath width of up to 1.2 km. Line spacing ranged from nearly 1,000m in flat areas down to 400m in steep terrain. Side-scan mosaics were generated with a 1m resolution. Selected areas were targeted by the higher resolution 410 kHz transmitter as well as by bottom photographs flying as low as a few meters above the seabed. The vehicles navigated autonomously using a combination of inertial navigation (Kearfott T-24 or T-16 INS) and long baseline acoustic navigation by computing their range to two moored acoustic transponders. Working efficiently in this rough topography at speeds above 3 knots was only possible due to the obstacle avoidance capabilities of these AUVs.

Jan 1, 2011

By R A. Stevenson

The purpose of this paper is to outline a recent development in ground fault protection. The paper deals with the A problems of both grounded and ungrounded systems, with regard to hazards to personnel and equipment, and shows that the increased sensitivity and speed of operation of this new detector results in increased safety to personnel and reduced stresses on equipment, and permits the detection of leakage currents before they become serious faults. The detector can be applied to all distribution systems, either A.C. or D.C., up to 15 kv., and the detector itself can be tested at regular intervals without interrupting line circuits. T HERE is always controversy among engineers as to whether distribution systems should be grounded or ungrounded. There are many experi-enced engineers on both sides of this controversy, and each have valid reasons for their choice

Jan 1, 1964

The transgressive sedimentary sequence of the Noumea Basin contains rhyolitic lavas and less voluminous mafic and intermediate volcanics of shoshonitic affinities which erupted simultaneously during the late Cretaceous. The shoshonitic volcanism shows a trend froIn early mafic to younger evolved intermediate lithologies. The rhyolites are consistently calcalkaline. There is no evidence of mixing of the two magma types. The shoshonitic volcanism is the result of a short-lived subduction event related to spreading in the New Caledonia Basin and involved reactivation of an earlier esozoic subduction zone.

Jan 1, 1995

By G. L. Jr. Spencer

THERE is no question as to the importance of the part played by the retort in modern zinc smelting. A satisfactory retort should have properties that will result in resistance to slagging action and fire cracks, and have no tendency, or at least, only a small tendency, to soften and bend under furnace heat. The life and cost of a retort also are extremely important factors. The trend in zinc smelting during the past few years has been toward longer retorts and higher charge density. This is caused by the fact that the diameter is limited to 9 or 10 in. because of heat penetration difficulties in larger sizes. Consequently, increasing the length of the retort and density of charge offers the only practical means of increasing the amount of zinc produced per retort. The stiffness of a retort perhaps is the most important factor, as slag accumulates in the bottom of a retort which has sagged and very quickly cuts through, often ruining the retorts below. The development of the high-silica retort is a result of the demands made by the trend toward heavy charges.

Jan 1, 1931

By Thomas Pea, Heiner Kontrus, Jérôme Steinkühler

In tunnel condition assessment, the trend is towards comprehensive 3D measurement combined with high quality image texture to document and quantify damages to the tunnel surface and to create a cohesive data base of the structural conditions throughout its lifespan. The faster such measurements can be made on site, the less it impacts traffic conditions of the highly sophisticated subway systems. The Dibit high-speed 3D scanning system which is based on Photogrammetry and LiDAR technology enables data acquisition in tunnels at a speed of up to 60 mph. Given the high rate of speed the system can operate, tunnel shutdowns can be drastically reduced, and tunnel safety increased. The photorealistic texturing of the 3D-model allows the identification and analysis of smallest material damage (e.g., cracks ≥0.3 mm wide). The publication illustrates technical details and 3D results of the innovative system from measurements that were performed in the subway tunnels of the Bay Area Rapid Transit System in San Francisco, CA (total length 66.23 km).

Jun 13, 2021

By Walshe J. M.

The slow-speed compressor is giving place to the high-speed type, with its greater economy of material and space; and, where very large units are required, the turbo-compressor is supplying the need. In the very large air-supply stations on the Rand, turbocompressor units of a capacity of 20,000 and even 50,000 cubic feet, requiring 4,000 to 13,000 horsepower, are quite a commercial proposition, and have proved a practical success. Air-compressors of this size are, however, very exceptional, and the high-speed reciprocating compressor is quite capable of dealing with the highest outputs so far required in this country and, in the hands of manufacturers experienced in the design of high-speed steam-engines, a very high standard of reliability and efficiency in operation is obtained. The so-called “high-speed” or more correctly quick-revolution type of compressor is now extensively used in mines and collieries; for the air-pressures required for power purposes in mining work, two-stage compression, with an intercooler between stages, is the design usually adopted in best practice. It is not the writer’s intention to describe a variety of high-speed air-compressors but to select as an example of this type of compressor the one with which he is most familiar, and which is probably more largely used than any other, namely, the double-acting two-cylinder two-crank type with automatic light-plate air-valves, and with the working parts lubricated on the forced-lubrication principle. Sectional drawings, efficiency curves, air-cylinder diagrams and other data accompany the descriptions and photographs of compressor design, components and mine applications

Dec 1, 1916

By M. D. Lawton, P. Steen

"Drilling results from the established levels at AngloRouyn Mines Limited had indicated inadequate tonnages to meet the planning schedule. It was decided to develop the main zone of the orebody below the bottom working level of the mine. The orebody dips north at an average of 50 degrees and plunges to the west at about 10 degrees. Due to the need for rapid development of this area, a decision was made to use trackless equipment.This paper describes the method used and highlights the use of small 5-ton diesel trucks as carriers for the 2-cu.yd LHD machine. The method achieved advances of about 1,000 feet per month, at a dip of 12 degrees over a length of close to 2,000 feet, using as few as 20 men per day."

Jan 1, 1971

By E. A. Smith, E. R. Parker

METALLURGISTS and engineers have always been interested in the mechanism of high-speed deformation because metals are rapidly deformed in various applications and manufacturing processes. The deformation of metals by impact loads has recently engaged the attention of a number of investigators. Many of their results have not been disclosed but some of the published investigations1-8 have shown that the tensile strength, yield strength and elongation generally increase with increasing strain rate. The investigation reported herein is an attempt to determine the reason for this increase in strength and elongation. Single-crystal copper specimens were broken in tension at impact velocities up to 100 ft. per sec. The distribution of slip bands in the fractured crystals was found to depend upon the strain rate. In the bars broken at high speeds, the slip bands appear to be more numerous. This might account for the higher strength as well as the greater elongation. EXPERIMENTAL PROCEDURE Single crystals of copper (approximately 99.98 per cent) were made in graphite molds by the conventional method of lowering the mold out of the hot zone of a hydrogen furnace at a rate of one inch per hour. Solidification progressed from the bottom upward, forming a single crystal. The crystals were about 0.30 in. in diameter and 4 in. long. They were made into test bars by sliding threaded steel bushings over each end of a crystal and then flowing silver solder between the crystal and the bushing. The inside diameter of the bushings was slightly greater than the diameter of the crystals, to allow space for the silver solder. The bushings were placed so that the gauge length of the crystals was one inch. The assembly is shown in Fig. I, with two views of a fractured crystal. Annealed polycrystalline copper bars of similar shape were machined from solid stock. X-ray measurements were made on all single crystals to determine their orienta¬tions. The results are shown in Fig. 2, where the location of the axis of each specimen is indicated on a standard projection. The bars were broken in a commercial variable-velocity tension im¬pact machine, which has been described in detail elsewhere.7,8 The stress and strain were recorded by means of wire strain gauges and a special commercial oscillo-raph, also described in detail elsewhere.9,10 The equipment and method can be briefly described as follows. The impact machine consists of a motor-driven flywheel containing a two-pronged hammer. This hammer is held retracted in the flywheel

Jan 1, 1944

By S Wellink, D Chalmers, D Adermann, C Martin

The practice of recording blasts for quality control purposes has been conducted for several decades. However, at the low frame rates of a standard video camera, essential data is frequently missed as it occurs when the shutter is closed between frames.The use of high-speed video for the research, development and monitoring of the performance of blasting procedures is a well proven but under-utilised practice.The recent development of low cost, easy to use high-speed digital cameras and user friendly software can deliver a capability into mine management as a day-to-day production tool that can greatly improve blasting performance and reduce costs.Digital high-speed video and image analysis software can accurately quantify each blast. Analysis of the images can facilitate the identification of causes of variance from design, geology changes, errors in blast practice and areas of poor performance. The use of high-speed video greatly enhances the audit and review processes so that future blast design can be quickly and appropriately modified to deliver improved blasting performance and reduced costs.The three videos demonstrate the differences between standard video and high-speed video and the detail that can be obtained from them. These videos of open cut blasts can be used to identify blast performance variances. Capturing images at 1000 frames per second allows the analysis on a millisecond timescale where detonator timings, fragmentation, venting, fume generation and flyrock can be accurately identified.CITATION:Adermann, D, Chalmers, D, Martin, C and Wellink, S, 2015. High-speed video – an essential blasting tool, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 471–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Garland E. Likins

High-strain dynamic testing of drilled shafts and cast-in-place piles has become routine procedure in many parts of the world today. Field testing is performed by measuring strain and acceleration records under impact of a falling mass. Wave equation analysis is utilized to design the weight, drop height and cushion of the hammer apparatus to assure a successful test. The Pile Driving Analyzer* (PDA) and CAPWAP* methods are used for data acquisition and analysis. Testing results yield information regarding pile static bearing capacity, structural integrity, and pile-soil load transfer and pile load-movement relationships. This paper discusses application of high-strain dynamic testing to cast-in-place shafts with emphasis on aspects unique to this type of pile. Suggestions regarding minimum requirements for good quality tests are offered. Five case histories reported in the literature are summarized and a sample specification is also included.

Jan 1, 1995

By O. W. Ellis

RECENTLY there has been a considerable revival of interest in the effects of the various elements commonly added to brass for the purpose of increasing its strength. For many years the work of Guillet2? alone gave reliable information in this regard. Even today his determination's of the coefficients of equivalence of the various elements relative to zinc in brass are those universally employed in industry. This is so because these coefficients have stood the test of time-their substantial correctness has been proved in almost universal practice. It is not our intention to discuss here these coefficients or their use. Rather do we wish to emphasize the need for further systematic studies of the mechanical properties of the ternary systems of copper, zinc, and other individual elements. Since Guillet published the results of his first investigations Millington,16 Smalley33 and Thibaud45 have added somewhat to our information. In general they have confirmed the findings of Guillet, which may be stated in the following rather general terms: 1. The addition of aluminum to the 70:30 and 60:40 brasses progressively increases their hardness and strength and reduces their ductility and resistance to shock. 2. The addition of small amounts of iron to a 60:40 brass improves its strength without affecting its ductility. 3. The addition of small amounts of manganese to a 60:40 brass causes a progressive increase in its strength and reduction in its ductility. A considerable amount of information has been amassed in regard to the effect of nickel on brass (9, 22, 41) which it is unnecessary to refer to here, in view of the scope of this paper.

Jan 1, 1929

By J. B. Parry

Three types of high-strength cold-rolled steels are discussed. Two are currently being developed at Iscor: rephos phorized steel and niobium microalloyed steel. Heat treatment after cold rolling is carried out in batch annealing furnaces. A third type, dual-phase steel, which requires a continuous annealing treatment for economic production, is also described. The properties, strengthening mechanisms, and applications of these three steels are examined.

Jan 1, 1983

By E. M. Wise

THE properties required of gold alloys for jewelry are not well standardized, due in part to problems peculiar to certain branches of the jewelry industry, in part to the individual preference of the fabricator and to his willingness to cope with certain difficulties in manufacture, which arise with the use of certain alloys. GENERAL REQUIREMENTS In general, the properties desired may be classed as follows: 1. Color should conform to the dictates of good taste and smart style. 2. Corrosion resistance and tarnish resistance should be good. This is to a considerable extent determined by the carat. Resistance to such corrosive agents as mercuric chloride as well as certain depilatories is unreasonable to expect and difficult to meet. 3. Strength and hardness must be adequate to maintain the delicate contours of finely modeled jewelry. 4. Wear resistance must be great enough to resist abnormal wear, such as is encountered by a wedding ring in a lifetime of wear. 5. Ductility must be sufficient to permit the fabrication of drawn shells, tubes and difficult shapes. Material having a yield point of not less than 60,000 lb. per sq. in., an ultimate strength of 100,000 lb. per sq. in., and an elongation of 40 per cent. is desirable. 6. Melting point should be between 800° and 1200° C.

Jan 1, 1928