Search Documents

By Jie Zhu

Coal bumps are a special form of release of geologic strain energy that has already been one of the most dangerous hazards to underground mining safety in China. A number of coal-bump models have been developed to quantify coal failure under assumption that a bump is a kind of non-gas induced outburst. However, some technical experts in charge of micro-seismic and gas monitoring have found unusual gas emissions before and after bump, which suggests that it is possible for gas to trigger coal bumps. Considering the coal reservoir as geological body composed of the coal matrix and gas, a new model based on Lippmann?s bump model is proposed to understand the initiation of coal bumps. The redistribution zone from excavation of a roadway has been calculated and analyzed regarding its relation with mining depth. It is shown that high gas pressure may push the coal seam to overstep the critical state due to extension of the plastic disturbed zone, and this is harmful to the stability of coal seam. This model successfully explains the bump phenomena of the Xinzhouyao mine at shallow depth.

Aug 1, 2013

By C. Ramasamy

The tariff reductions on imports, as a part of on-going liberalisation process in India, has fueled competition within and outside India and has, in turn provided an opportunity to reach global markets. This change calls for quality upgrades and cost-competitiveness without impairing the environment. In this context, gas based processes, contributing to improvement in quality and environment as well as processes where controls are applied when gases inimical to environment are involved, are discussed in a remelt/cast-house scenario. The impact of such processes on fabrication cost of sheet ingot is seen alongwith consumption and cost of materials and compared with a world class standard plant in North America.

Jan 1, 1996

By D. Pawelus, J. Butra, R. Debkowski, M. Szpak

Impact of horizontal stresses on stability of underground workings in mines is a very important issue in underground mining. Identification of the initial state of stress in the rock-mass should be one of the main actions taken into account while designing and carrying out the mining activity in underground mines. The paper presents the tests on three dimensional stress pattern in Polish copper mines, owned by KGHM Polska Miedz S.A. Group, carried out in 2012. The research program covered 7 measuring stands in two mines; their average depth was about 1000 m. The main aim was to identify the values and directions of horizontal stresses in order to optimize the extraction and to improve the safety. The overcoring method with the use of CSIRO HI type probe was applied. The paper also describes the measuring technique which was developed for the purpose of specific mining and geological conditions of KGHM mines, taking into consideration the natural hazards encountered there as well as technical and operational capabilities with regard to drilling equipment. The experience gained during the underground measurements and the issue of making such measurements in underground copper mines in Poland are presented in the paper. The stress patterns obtained during the underground measurements are of application importance for the process of designing the spacing of mine workings and improving their stability and mine support selection.

Jan 1, 2015

By C. Zangerl, H. Lechner

"Large scale rock slides in deeply incised Alpine valleys are common hazards that can endanger human life, settlement areas and critical infrastructure such as highways, railways and reservoirs (Bonzanigo et al., 2007). In order to perform reliable forecasts of the behaviour of rock slides influenced by large dam reservoirs the geometry, the kinematics, the deformation behaviour and the hydrogeological situation need to be understood profoundly. Based on generic rock slide models the influence of the rock slide geometry on the stability as well as the impact of the buoyancy forces and water load of the reservoir at the toe of the slope are the main focus of this study. Various assumptions of hydraulic conductivity, groundwater conditions of the rock slide and impoundment depth of the reservoir are analysed using limit equilibrium approaches.Generally, deep seated rock slides are characterised by deformation along one or multiple shear zones where most of the measured total slope displacement localizes. Many large rock slides, especially those observed in foliated, mica-rich crystalline rock masses (e.g. paragneisses, mica schists, phyllites), do not fail suddenly or reach high velocities. Instead, many of them move slowly and reach velocities of centimetres per year or even less. Some show episodic accelerations, sometimes reaching alarming levels, but then subside to non-critical levels again. However, there is a potential that deep-seated rock slides fail rapidly, develop into far-reaching run-out rock flows, and cause catastrophic events. Whereas the role of triggers in promoting phases of acceleration is often understood, the same cannot be said regarding the kinematics and dynamic processes by which the rock slide mass decelerates, re-stabilises or accelerates to a catastrophic degree once the trigger impetus has been removed. Thus key questions of the presented work concern the geotechnical, geometrical and hydrogeological conditions under which a slowly moving rock slide is triggered to accelerate to irreversible, maybe dangerous velocities. The development of the sliding zone is generally influenced by pre-existing discontinuities such as brittle fault zones, shear and tensile fractures, foliation and bedding planes. These geological structures determine the geometry of the sliding zone which can either be rotational or translational. During the gravitationally induced failure process the geometry of the rock slide undergoes a change.Several observed post-failure geometries in metamorphic rocks show a concave topography in the middle to upper part of the rock slide and a typical convex or bulge-like topography at the toe of the slope (Zangerl et al., 2012). Whereas the sliding zone of the upper part of such a rock slide mass is rather steep and planar, the inclination of the sliding zone at the toe can be close to zero and act against the driving forces (Alonso et al., 2010). A shear zone that meets alluvial deposits at the foot of the slope encounters a stabilizing impact on the mechanical behaviour. This buttressing effect of alluvial sediments has a remarkable influence on the slope stability."

Jan 1, 2015

By D. Richers

When modeling predictive pit lake chemistry, groundwater chemistry is integrated with the affected portions of the wall rock and chemistry of the lake in a complex series of mixing. Fractions of the solutions impinge upon fresh, unaltered or fractured and oxidized zones of the wall containing sulfide materials and/or soluble metal/metalloid salts. Changing conditions over the short term (biannually) and long term (decades) can drive reactions allowing for dissolution or precipitation of acid rock drainage and metal leaching (ARD/ML) constituents. Local zonal variations can result in a portion of the pit releasing materials into solution; whereas other portions of the lake might favor the formation of colloids or precipitants. The proportions and character of groundwater can drive the chemistry of the pit lake provided sufficient buffering capacity is available to temper the generation of ARD in the system. For sulfide-rich systems, reduction of oxygen by rapid inundation and consumption by sulfides is key to reducing the ARD/ML. This paper presents several models of a sulfide-rich wall rock system using a range of groundwater chemistries to show these constraints.

Jan 1, 2012

By N. Edmonson

During the last 30 years, a dramatic increase in the supply of byproduct sulfur substantially reduced the share of the market held by Frasch-mined (non-by-product) sulfur in North America. Even though Canadian sulfur production is not discretionary, the geographic remoteness from the large US markets and the high transportation costs associated with delivering sulfur to those markets has meant that Canadian producers act like discretionary producers in many important ways. They have effectively replaced the US Frasch producers as the cost-marginal sulfur source to large US markets. Implications of this change in market structure include more volatile sulfur prices and longer sulfur price recessions.

Jan 1, 1998

By N. Edmonson

During the last 30 years, a dramatic increase in the supply of byproduct sulfur substantially reduced the share of the market held by Frasch-mined (non-by-product) sulfur in North America. Even though Canadian sulfur production is not discretionary, the geographic remoteness from the large US markets and the high transportation costs associated with delivering sulfur to those markets has meant that Canadian producers act like discretionary producers in many important ways. They have effectively replaced the US Frasch producers as the cost-marginal sulfur source to large US markets. Implications of this change in market structure include more volatile sulfur prices and longer sulfur price recessions.

Jan 1, 1997

By Bernd Hagenah, Petr Pospisil, Colin Santangelo

This paper explores the profound implications of high-speed train operation on tunnel planning, specifically investigating ongoing high-speed rail projects in California and Texas. The paper delves into the crucial considerations for designing high-speed rail tunnels, including selecting tunnel sections based on aerodynamic factors, which impacttraction power requirements and pressure comfort. The paper also examines the need for emergency stations, maintenance access, and comprehensive safety and rescue concepts to address train incidents. Drawing from international high-speed rail projects, it shares valuable experiences and lessons learned to promote efficient and secure tunnel designs for high-speed train operations.

Jun 23, 2024

By G Bournival, Y Saavedra Moreno, S Ata

Flotation frothers are heteropolar molecules that are preferentially adsorbed at the bubble interface to enhance the flotation performance by promoting the formation of small and stable bubbles. Frothers have different characteristics that can be used to classify them. A classification framework has been recently presented by Saavedra Moreno et al (2022) to classify non-ionic frothers by conducting a principal component analysis (PCA) and a hierarchical clustering analysis (HCA). However, for the purpose of the present research, only five frother characteristics, including molecular weight (MW), hydrophile–lipophile balance (HLB), critical coalescence concentration (CCC), the minimum Sauter mean diameter (DL), and foam stability index (DFI) were used in the PCA and HCA. All those characteristics were evaluated for a two-phase system in the absence of particles. Realising the important role that particles play in froth stability and behaviour, the effect of hydrophobic particles on the presented frother classification framework was investigated in this study. Four frothers with different characteristics, methyl isobutyl carbinol (MIBC), 1-pentanol, tri (propylene glycol) (TPG), and tri (propylene glycol) methyl ether (TPM), were chosen. The experiments were carried out in the presence and absence of silica particles esterified with 1-pentanol. It was evident that the results for 1-pentanol, TPM, MIBC, and TPG in the three-phase system agreed well with the frother classification presented for the two-phase system as frothers were clustered in the same groups. The findings from this research support the use of the frother classification system presented in two-phase system to select a specific frother for a particular application without the necessity of conducting laborious experiments in a three-phase system.

Aug 24, 2022

By P K. Singh

Recent advancements in understanding the detonation process are noteworthy, but they are still based on somewhat hypothetical situations. The actual variables that are essential parts of normal blasting practice have not yet been taken into account in such treatments. These include the various initiation practices employed to detonate a column of explosive, from single point initiation to multi-point initiation in blast holes, and the effect on detonation characteristics of both detonators and explosives under multi-deck and multi-hole blasting conditions. The in-the-hole velocity of detonation (VOD) of an industrial explosive is dependent on explosive’s charge diameter and blasthole diameter. The relationship between blasthole diameter and VOD provides a fundamental guideline to the rate of energy conversion and energy release within the detonation front on the interaction of explosives with the confining medium.The in-the-hole VOD of explosives was measured at four experimental sites in India for different blasthole diameters, ie 150 mm to 311 mm, but for identical explosive composition being same particle size, density, viscosity and loaded into blastholes with the same degree of confinement. The results of the studies demonstrated that there is definite relationship in in-the-hole VOD of the explosive and the diameter of the blast hole. The study also confirmed that the explosives initiated with concentrated boosters yielded higher VOD in comparison to those explosives that were initiated with multi-point priming. The measured increase in VOD of explosives for increasing diameter of holes was up to 24 per cent. The rate of change in in-the-hole VOD of explosives increases with increasing blasthole diameter. It can be further stated that the in-the-hole VOD of the explosive reaches a fairly constant value after reaching a limiting/threshold diameter of 311 mm.

Nov 8, 2011

By Klaydison Silva, Pedro Silva, Letícia Damet

The current situation of the global mining economy is increasingly focused on the utilization of materials previously discarded in the mining process. The waste from the past, through new processing routes, is gaining new contours for use as high-value-added products. The strategic mine planning process has consequently had to adapt to the new economic reality. In standard scenarios, the focus was primarily on mine sequencing aimed at the highest economic return, with all infrastructure allocated as a necessity of mining. This work aims, in strategic planning, to configure and select the best composition of mining structures. The entire Mine-Plant-Waste-Tailings-Products chain will be considered as a factor in the sequencing of a multimine complex, to achieve the most sustainable utilization of the current mines’ waste. The sequencing is based on concurrent flows of process configurations and capacities, structure sharing, and flexibility of feed types. These factors will guide the sequencing, which will be constrained by components such as waste and tailings disposal rates, lithology feed relationships, and especially product composition through market specifications, all while respecting product shipping capacities.

Feb 22, 2026

By M. D. Banghart

The Republic of South Africa is an outstanding example of the benefits to a new land by the application of individual enterprise, capital and know-how. While South Africa was colonized by European and Bantu people some 300 years ago, it was only 70 to 80 years agog when diamonds were discovered at Kimberley and gold on the Witswatersrand, that the mining, industrial and commercial potential of the country began to emerge. South Africa s national income rose from R1, 200 million in 1945 to over R4 billion in 1960 (1R = 10 shillings = $1.40 U. S.) The annual national income per head of population -- including all races -- is currently R254 (£127) This compares with £24 for India., £30 for Nigeria, and £50 for Ghana. Allowing for the increase in population, the increase in real income per head of population was about 40% during the past 15 years.

Jan 1, 1962

By J. Routh

Analysis of AI, As, Ba, Be, Ca, Cd, Co, Cu, Fe, K,. Mg, Mn, Mo, Na, Ni, Pb, Sb, Se, Sr, 11, V and Zn in various types of samples collected at Van Stone mine (a Pb-Zn deposit in Washington) and surrounding areas indicates that the concentrations of several elements in water, soil and sediment are higher than their background. values. Concentrations of metals in water decrease sharply downstream and are below the maximum contaminant levels specified for drinking water. Under present physico-chemical conditions, contamination of water is insignificant but the enrichment of heavy metals is found in soil and sediment.

Jan 1, 1994

By M. P. Hardy, C. J. H. Brest van Kempen, H. N. Maleki

To evaluate the influence of uniformly tensioned roof bolts on roof stability, mechanically anchored roof bolts were installed using the conventional bolter and a specially developed thrust and torque controlled retrofitable box mounted on a bolting machine. Thirteen thousand bolts were installed over 19 crosscuts in a 4 heading development in an operating coal mine. Geological , bolt and mine parameters were recorded at bolt installation, and bolt tension histories, roof sag and other changes evident in the rooms, crosscuts and intersections were recorded over a 2 month period. In all, 24 variables and 11 responses were quantified at 67 bolt clusters. These data were analyzed statistically to determine the significant variables influencing roof stability. As the mine development was safe and stable during the monitoring period, roof sag after two months was used as an index to quantify "stability." The variables of significance were shown to be coefficient of variation of bolt tension, bolt anchorage capacity, roof lithology, roof shape, standard deviation of bolt tension, and dip of roof lithologies. It was concluded that of the variables with which the mine operator has control, bolt tension uniformity was the most significant parameter at this mine. Other variables, such as intersection type and time between mining and bolting , were not significant, whereas, some other potentially significant variables such as horizontal stress or roof joint frequency did not vary sufficiently for their influence on stability to be evaluated.

Jan 1, 1986

By Deepak Malhotra, William F. Riggs, Edward C. Dowling

INTRODUCTION Mining companies are In the business of making an acceptable profit on their Investments, It became obvious in the recent recession that economic profitability/viability depends on being the lowest cost producer In order to compete on a global basis. The burden of achieving this objective falls on the mineral manager. He must strive to produce a salable product in an environmentally acceptable process while continuously Improving the profit margln.(1,2) Metal prices fluctuate on a regular basis. They directly Impact revenue and hence operating philosophy. The mineral engineer needs to develop an optimum operating strategy to meet his overall objectives, One would expect that, In the modem era of complex computer models, it would be easy to develop an economic model to maximize profits and/or cash flow. Discussions with mill managers Indicate that one mine/corporation's optimum operating strategy is not necessarily optimum for another. This paper approaches the problems from basics "Economics 101" and Illustrates the complexity of developing a universal model which can be applicable to all mines. Case examples are used to illustrate the need for better communication to avoid the basic economic fallacy “that optimization of segments leads to optimization of the whole system.” TECHNICAL MODELS Technical models are a prerequisite to the development of economic models because they provide the necessary Input data to these models, The flow of material from a mine through the sale of the finished product is shown In Figure 1. The ore Is mined and milled, and the concentrate can be stored for sale or smelted and refined In-house or at a toll facility. The finished product(s) are held In Inventory until sold either through existing contracts or in the spot market. [ ] Fairly reliable technical models have been developed for mining, milling and smelter operations. Mine plans are developed to provide a good Indication of the relationship between production and cut-off grade. It is easier to change surface mine plans than plans for underground mines. However, there are limits to maximum production that can be achieved with existing equipment. It Is possible that mine benches may not be developed to handle additional equipment, even If It was purchased to enhance production. More often than not, the cut-off grade Is lowered to Increase throughput goals.

Jan 1, 1993

By J. Koike

Mg alloys for structural application have attracted much attention. However, high process cost and poor mechanical reliability are major concerns upon expanding the application to a wider area. In order to break through these barriers, better ductility is desired at lower temperature. Plastic anisotropy and peculiar twin formation appear to play key roles in the deformation and fracture mechanisms of Mg alloys. In the paper, dislocation slip and twin formation are reviewed. The effects of crystallographic texture and grain size are discussed. The results suggest that a good control of microstructure and texture can improve ductility and mechanical reliability of Mg alloys.

Jan 1, 2006

By M Pizey, M Kingsbury

Since 1950 Stockton Open Cast Mine has excavated over 60 million tonnes of Brunner Coal Measures overburden sandstones and mudstones. The current operator, Solid Energy New Zealand, recognises that acidic drainage from this overburden and from historic underground mines has led to depressed pH levels and elevated levels of metals in streams draining the Stockton Plateau. These streams report to the Ngakawau River. To quantify the effects of mine site acid drainage remediation/mitigation on the lower Ngakawau River water quality, a catchment hydrogeochemical model has been field calibrated and ecotoxicology tests have been undertaken. The hydrogeochemical model indicates that pre-mining and present pH values in the lower Ngakawau River are similar but present aluminium and iron concentrations are elevated. Ecotoxicology tests have semi-quantified the critical metal concentrations and interim water quality targets to achieve ecological recovery are presented. Analyses of long-term total suspended solids (TSS) and turbidity monitoring in the lower Ngakawau River and St Patrick's Stream indicate that TSS of 120 mg/L and turbidity of 20 NTU are exceeded for <20% per cent of the time. Hence, specific criteria to protect migratory native fish from turbid water are currently met in the Ngakawau River and St Patrick's Stream.

Jan 1, 2003

By J-F. Turgeon, Y. Pépin, G. Hudon

The high temperature hydrochloric acid leaching of titanium slag in the QIT upgraded slag process (UGS) creates a harsh environment for materials of construction. Because of their excellent chemical and heat resistance, furan mortars are a key component in the lining system of the UGS pressure leach reactors. Similar products coming from different manufacturers have however shown unequal performances in service. In some cases, cracking of the brick lining has occurred during curing of the mortar. This study was initiated to investigate the impact of the curing conditions on the properties of carbon filled furan mortars. Laboratory tests were conducted to assess the effects of temperature and exposure to water and HCl solutions on mortar shrinkage and mechanical properties (tensile, compressive and bond strength). Three commercial furan mortars that have been used in the UGS leach reactors were thus characterized. Mortar properties were found to vary significantly among the products tested. Moreover, the curing conditions were shown to have a significant impact on mortar shrinkage and mechanical strength. The experimental findings provide explanations for the unequal performances of the mortars in service and for the problems of brick lining cracking that occurred in the UGS leach reactors. This study demonstrates that excessive mortar shrinkage compromises the integrity of a brick lining system.

Jan 1, 2004

By R. E. Ray

In an effort to reduce the risks to underground miners of health hazards associated with exposure to high concentrations of diesel particulate matter(dpm), the Mine Safety and Health Administration(MSHA) published proposed rules in 1998 limiting dpm exposure in both underground coal and metal and nonmetal mines. The proposed rule for underground coal mines would require removal of 95% of dpm by mass, while the rule for metal and nonmetal mines would eventually limit total carbon exposure from dpm to 160 micrograms per cubic meter of air over an eight-hour shift. The comment period for both proposed standards ended on July 26, 1999.In this session, representatives from MSHA, the National Institute for Occupational Safety and Health (NIOSH), equipment manufacturers, labor and industry will discuss the impact of the proposed regulations on mine operations and worker health. Questions will be taken from the audience after brief presentations from each panelist. This paper provides a compilation of written summaries of each panelist’s opening presentation.

Jan 1, 2000

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and thus deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the go band to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Feb 27, 2013