Search Documents

By Luke L. Y. Chang, Bert Phillips

A number of molybdenum oxides have been synthesized and their crystal structures have been described.' No data have been published on the stabilities of these oxides nor on the phase relations in the system Mo-0. It is probable that the tendency toward oxidation of both the metal and the oxides with low oxygen content in addition to the high volatilization rate of the oxides with high oxygen content have precluded accumulation of reliable data for establishing phase relations. These problems make experimentation difficult, but a modifi-

Jan 1, 1965

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

Hydrogen forms a beta-stabilized system with titanium, with a beta eutectoid at about 300°C and 44 atomic pct H2. 'The solid solubility of hydrogen in alpha decreases from about 8 to about 0.1 atomic pct from 300°C to room temperature. Hydrogen has little effect on tensile properties, but decreases notch-bar toughness to a large degree. This latter effect appears to be the result of increased notch sensitivity. PRIOR to this investigation, only a small amount of information was available on the effect of hydrogen on the mechanical properties of titanium. The effects of the other interstitially soluble elements, carbon, oxygen, and nitrogen, had received detailed study. Jaffee and Campbell1 indicated that hydrogen up to 1 atomic pct did not affect tensile properties deleteriously. Pitler' indicated that 1 atomic pct H, in titanium reduced the impact strength appreciably, but his alloys contained appreciable amounts of oxygen, and it was difficult to attribute the embrittlement entirely to hydrogen. The high temperature portion of the equilibrium diagram for the Ti-H system was established by McQuillan," and his data generally corresponded with the results of Kirschfeld and Sieverts," Gibb and Kruschwitz," Bevington, Martin, and Mathews," and other investigators. The lower concentration limit of the hydride phase varied considerably among investigators, and Gibb and Kruschwitz9 ad shown that small amounts of contaminants in either titanium or hydrogen caused considerable variation in this lower limit. In view of this pronounced effect of contaminants, the extrapolated value of McQuillan's, about 48 atomic pct at the 325°C eutectoid, appeared the most reasonable. McQuillan's lowest experimental value was 54 atomic pct at a temperature of 450 °C. The density of titanium had been shown to decrease with increasing hydrogen content, but discrepancies were noted among the various investigations. The best values indicated that the density was decreased from 4.56 grams per cc at 0.27 atomic pctl to 3.84 grams per cc at 61.3 atomic pct? This investigation was conducted to determine the effects of hydrogen on a titanium, both in high purity and commercially pure metals, and on high purity a titanium alloys. Material and Fabrication The literature indicated that impurities in either the hydrogen or the titanium must be kept to a minimum. For this reason, the initial studies were made with high purity iodide-refined titanium. The vendor's analysis of the iodide titanium and the hydrogen content of the as-fabricated Y4 in. diameter rods are shown in Table I. Two 1 lb ingots were prepared by arc melting under argon in a water-cooled crucible, using a water,cooled tungsten electrode. This equipment has been described.' As-cast Brine11 hardness numbers of 88 and 58 for these ingots were low enough to insure that the high purity of the metal was maintained during arc melting. The ingots were hot forged to % in. diameter rods at 800°C, cleaned by grit blasting, and then cold swaged to Yz in. diameter rods. The rod was then air annealed at 725 "C, ground to remove scale, and cold swaged to Y4 in. diameter (75 pct reduction in area). The material was then annealed for 1 hr in argon at 800°C to develop an equiaxed a grain size of about 0.05 mm. Micro tensile specimens and microimpact specimens were machined from this rod prior to treatment in the Sieverts-type absorption apparatus. Two lots of commercially pure RC-55 titanium were also used in this investigation to determine the effects of hydrogen and the normal impurities on mechanical properties. The commercially pure RC-55 alloy was obtained in the form of % in. diameter rod. The analysis of this material is also given in Table I. The % in. diameter rods were hot swaged

Jan 1, 1955

By J. W. Cuthbertson, R. A. Cresswell

THE constitution of Cu-rich alloys with 1.5 to 13.5 pct Sn and 0.25 to 3.0 pct Be and the precipitation-hardening characteristics of alloys with 1.5 to 13.5 pct Sn and 0.25 to 1.0 pct Be have been examined. The hardness and tensile strength of the alloys examined increase markedly after solution treatment at 700°C followed by heat treatment at temperatures between 200" and 450°C. By a combination of cold work and heat treatment, hardness values similar to those exhibited by commercial Be-Cu alloys containing 2.25 pct Be can be obtained with ternary alloys containing 9 pct Sn and 0.75 pct Be and containing 10 pct Sn and 0.5 pct Be. Marked hardening effects occur with alloys containing even less beryllium. By heat treatment alone, a hardness value of 310 diamond pyramid hardness can be obtained from an alloy containing 10 pct Sn and 0.75 pct Be. Preliminary tensile tests have shown that an ultimate tensile strength of 110,000 psi with an elongation of 23 pct is obtainable by precipitation hardening an alloy with 8 pct Sn and 0.75 pct Be. The precipitation-hardening process has been followed microscopically for certain alloys and the inference is that, while the initial hardening effect is probably explained by the precipitation of the ß phase of the Cu-Be system, further hardening, proceeding at a much slower rate, also occurs, apparently as a result of precipitation of phases of the Cu-Sn system, particularly precipitation of the 6 phase at temperatures below 350". The presence of the e phase of the Cu-Sn system in certain alloys at temperatures below 350°C has been confirmed. Tin-bronzes are widely used in engineering applications where a combination of high strength and good resistance to corrosion is wanted. The maximum strength is induced in these alloys by cold working, and it would be an advantage for many purposes if high strength could be achieved alternatively by an age-hardening process. While Cu-Sn alloys have a good fatigue resistance they can be surpassed in this respect by Cu-Be, but the use of the latter alloy is limited by its high cost. If, by adding beryllium to tin-bronze, the properties of the respective binary alloys could to some extent be combined, a most attractive alloy should result. As pointed out by Raynor,¹ beryllium is on the borderline of the zone of favorable size factors for copper, and the solid solubility of beryllium in copper is consequently much more restricted than if the size factor were strongly favorable. The size factor is sufficiently favorable, however, to permit an increase in solid solubility with rise in temperature, and there is thus a composition range in which CU- Be alloys are susceptible to hardening by precipitation heat treatment. Although the a phase of the Cu-Sn system is similarly susceptible to precipitation treatment, the time necessary to establish equilibrium in commercial alloys of this type is usually so great that age hardening becomes impracticable. The addition of beryllium to Cu-Sn alloys would appear to offer a means of conferring on the latter useful age-hardening properties. Masing and Dahl² and others have, in fact, shown that the addition of beryllium to Cu-Sn a solid solutions renders these alloys susceptible to precipitation hardening and after such hardening confers on them an encouraging improvement in physical properties. If this improvement could be achieved by the addition of substantially smaller amounts of beryllium than are customarily found in binary Cu-Be alloys, the ternary alloys should possess economic advantages which might make them more attractive than the binary alloy for some applications. Binary Systems Copper-Tin: The constitution of these alloys is now reasonably well known and is summarized in the equilibrium diagram published by Raynor.³ The following observations, due to Raynor,¹ on the structure of those phases of the Cu-Sn system that are likely to be found in the ternary alloy system will facilitate the subsequent discussion on the examination of that system. The ß phase is an electron compound at the electron-atom ratio 3:2 and has a body-centered cubic crystal structure. This phase is stable only down to 586°C, at which temperature it decomposes eutectoidally into the a and y phases. The y phase has a structure that is also based on the cubic system. This phase is stable down to 520°C, at which temperature it decomposes eutectoidally into the a and d phases. The d phase is an electron compound (Cu³¹Sn8) which has a crystal structure analogous to that of 7 brass. This phase is stable from 590" to 350°C; on prolonged annealing at the latter temperature it breaks down into a mixture of the a and E phases. The e phase is an electron compound (Cu³Sn) having the electron-atom ratio 7:4. Its structure may be regarded as a superlattice based on the close-packed hexagonal system. This phase is stable from 676°C to room temperature. The primary solid solubility of tin in copper increases to a maximum of 15.8 pct as the temperature falls from that of the peritectic reaction to 586°C. The solid solubility remains constant from 586" to 520°C. At lower temperatures the solubility decreases progressively. Below 350°C the fall in solubility is pronounced and is associated with the precipitation of the e phase. This precipitation is very sluggish and does not normally occur under service conditions. Copper-Beryllium: The Cu-Be system has been investigated by Borchers' and others. Raynor5 summarized the present state of information on it.

Jan 1, 1952

By K. M. Weigert

The position of the three-phase field between the alpha and the beta phases was established. The exact location differs from previous assumptions. The extremely high strength and hardness values were found near the phase boundaries of the ternary compositions. IN 1929, UenoL investigated vertical sections of the Ag-Cu-Zn diagram at constant silver and zinc values. From the evaluation of cooling curves and microscopic studies, he concluded that there was no evidence of a three-phase field in the solid state between the a and ,8 fields. The failure to find evidence for this field was due to the fact that it exists only in a very narrow range of compositions and requires special methods of heat treatment to establish phase equilibrium. In a later publication on the same subject Keinert2 rearranged Ueno's diagrams to conform with the basic phase rules. The existence of a three-phase field was postulated in the solid state between the a phases and the homogeneous ,9 phase between the Cu-Zn and the Ag-Zn binary border systems. The approximate location was based on a few microscopic observations of the structure and it was pointed out that the exact position could be determined only by a larger number of experiments. In the twenty years following these investigations alloys of Ag-Cu-Zn have become of general interest due to various technical applications, principally for brazing. In the course of an overall investigation of the physical properties of ternary Ag-Cu-Zn alloys the author found extremely high values of hardness and strength in alloys of compositions between the a and the yS fields. The exact location of the intermediate phase fields was established by the evaluation of more than a hundred cooling curves and microscopic mountings. Experimental Procedures Preparation of Test Samples: At the beginning of the investigation samples were chillcast into Vi in. diameter iron molds to determine hardness, strength, and the mechanism of primary crystallization. These

Jan 1, 1955

By F. H. Wilson, E. W. Palmer

The solid solubility of iron in 2 to 10 pct cupro-nickels increases with temperature and nickel content. Property changes accompanying various heat treatments indicate typical precipitation hardening behavior. Iron content also affects softening temperature and sub-scale formation. These factors, as well as impingement corrosion resistance, influence the optimum iron content of commercial alloys. FOR many years Cu-Ni alloys have been used extensively in the form of tubes, pipes, and plates for the construction of salt-water lines and surface condensers on shipboard and in tidewater power stations. The 30 pct Ni alloy has been considered more resistant to rapidly flowing sea water than alloys of lower nickel content, and has been standard on ships of the U. S. Navy. Some ten years ago, the still better corrosion resistance obtained by modifying the 30 pct Ni alloy with approximately 0.5 pct Fe was recognized, and the iron-bearing alloy rapidly superseded the plain alloy as the standard material for severe service. In 1945, Tracy and Hungerford1 published a study of the effect of iron on the corrosion of various cupro-nickels in sea-salt solutions, and their data indicated that the 10 pct Ni alloy containing about 0.75 pct Fe was equivalent to the 30 pct Ni alloy containing 0.5 pct Fe. This was confirmed by LaQue in discussion of the above paper, and by results in an experimental condenser set up at the Kure Beach marine test station of The International Nickel Co., reported by Freeman and Tracy.' The 10 pct Ni iron-bearing alloy is now being very widely used in applications where the 30 pct Ni iron-bearing alloy was formerly considered standard. While this "substitution" has undoubtedly been stimulated by the present extreme shortage of nickel, it must be emphasized that it involves no loss of service performance, and would have occurred anyway in the course of time, for economic reasons. In view of the increasing use of the 10 pct alloy, it seems desirable to make generally available the results of several investigations of Cu-Ni-Fe alloys carried out in the Metallurgical Research Laboratory of The American Brass Co. in recent years. The present paper, deals with the constitution of these alloys in the copper-rich corner of the system, and with the variations in hardness and tensile properties resulting from the heat treatment of alloys containing various amounts of iron. Most of this work is concerned with alloys containing 10 pct Ni. With over about 0.75 pct fe, the 10 pct Ni alloy is suscep- Alloys Several series of cupro-nickel alloys containing iron were used in these investigations. Most of them were prepared in the laboratory, but two samples of commercially fabricated alloys were included. Series A—Nominally 2 and 5 pct Ni, each with 0 to 1.5 pct Fe. Series B—Nominally 10 pct Ni with 0.1 to 0.4 pct Fe. Series C—Nominally 1.0 pct Ni with 0 to 2 pct Fe. Series D—Nominally 10 pct Ni with 3 to 5 pct Fe. Series E—Nominally 10 pct Ni with 1 and 1.5 pct Fe.

Jan 1, 1953

By A. A. Bauer, H. A. Saller, F. A. Rough, J. R. Doig

among uranium alloy systems are the U-Zr, U-Ti,and U-Mo binary systems, in that an intermediate phase, of limited solubility range, exists in each system. These intermediate phase alloys offer a promising field of investigation, both as binary alloys and as ternary alloy combinations. While a limited amount of work has been done on the binary alloys, none has been done on ternary combinations of these alloys. As a possible prelude to more intensive investigation of these systems, a study of the phase relationships between the 6 phases of the U-Zr and U-Ti systems was undertaken. The solid-state portions of the binary constitutional diagrams for the U-Ti,1 Zr-Ti,2 and U-Zr3 systems are shown in Fig. 1. The solid to liquid transformations are not shown, as these transformations were not studied in the ternary system. The phase designations employed are based upon those shown in the uranium constitutional diagrams. The crystal structures of the various phases are given in Table I. Experimental Materials and Methods The ternary section presented is based upon the results of thermal, metallographic, and X-ray analyses of a series of alloys ranging in composition between the phases of the U-Zr and U-Ti systems (U-74 atomic pct Zr to U-35 atomic pct Ti). After preparation of the alloys, thermal data were obtained. On the basis of these data, specimens were heat treated and examined metallographically. Specimens were then selected from those heat treated for X-ray determination of the phases present in what were considered critical phase regions. Alloy and Specimen Preparation—Alloys for this investigation were prepared from selected as-reduced uranium and crystal-bar zirconium and titanium. For nominal compositions, see Table 11. Charges were arc melted from five to seven times under a helium atmosphere, finally being cast into wire-bar form for fabrication. A zirconium getter button was used to clean the furnace atmosphere prior to melting. The alloys were homogenized 20 hr at 900 °C and furnace cooled. A portion of each bar was then removed for thermal analysis; the remainder was saved for fabrication. Alloys 8 through 14 were placed in steel tubes along with zirconium getter chips and, after flushing with argon, the tubes were welded shut and rolled at 1500 °F to a 50 pct reduction in diam. The remaining alloys were annealed 24 hr at ll00°F to insure transformation of the ? phase to the 8-U2Ti phase and were then hot rolled from a salt bath. Attempts to roll alloys 6 and 7 at 1100 °F were unsuccessful. Following this, attempts were made to roll pieces of alloys 1 through 5, which had cracked rather severely during casting, at 1200 °F, but these efforts were also unsuccessful. These alloys were, therefore, further treated in their cast and homogenized condition. All alloys were pickled to remove oxide formed during rolling. Thermal data were obtained on these alloys by conventional differential thermal analysis at a heating rate of 30C per min, and by a high-speed heating method at rates of approximately 10°C per sec. For the latter method of analysis, a 36-gage Chromel-Alumel thermocouple is spot welded between two slivers of alloy, the sandwich being en-

Jan 1, 1958

By L. W. Reynolds, R. F. Campbell, K. G. Carroll, S. H. Ballard

Based on metallographic and X-ray data probable equilibrium conditions from 1340" to 2400°F are presented for the composition range investigated. These are correlated with investigations of Takei and Kuo. Provision is made for existence of Mo, C and (Fe, Mo)2,C, carbides heretofore omitted in diagrams in this composition range. These carbides and (Fe, Mo),C, in equilibrium with ferrite and austenite, restrict the austenite and austenite + ferrite fields to lower carbon contents and higher temperatures than in the Fe-C system. OK groups of steel of different molybdenum content, but with approximately the same carbon variation in each group, Table I, were studied. The alloys were melted in an acid-lined 30-lb high-frequency induction furnace, and the ingots forged to l-in. rounds, which were then ground to 0.75-in. diam. To minimize chemical segregations a short length of each bar was given a high-temperature heat treatment as listed in Table I. Specimens 0.062 to 0.125-in. thick were thereafter cut from the homogenized bars for heat treatment to determine phase changes in the alloy. Heat treatments were performed in either a lead bath or muffle-type electric furnace, depending upon the temperature required. Maximum temperature variation was * 2" F in the lead bath and * 5"F up to 1900°F and +8"F above 1900°F in the electric furnace. Adequate protection of the specimen from the oxidizing atmosphere in the electric furnace was obtained by sealing the specimen in either a pyrex or a silica capsule which was evacuated or not as circumstances required. For austenitizing followed by quenching to an isothermal temperature, the specimen was placed in a closed-end refractory tube the mouth of which, extending beyond the furnace, was connected to a vacuum pump. The specimen could be withdrawn from this tube and quenched as desired. IDENTIFICATION OF PHASES The principal method of identification of phases was metallographic examination conducted on surfaces well removed from exposure to lead or atmosphere effects during heat treatment. Hardness measurements (Dph/lOkg) were also made on these surfaces. The etching reagents used and their effects are listed in Table II. Martensite and ferrite were readily recognized by their customary appearance after etching with saturated picral or 1 pct nital. The presence of liquid at high temperature was indicated by curved interfaces characteristic of boundaries between solid and melt, by intergranular pools of dendritic areas in a carbide matrix, and by a black network coincident with austenite grain boundaries. Examples of these structures are shown in Figs. l(a) and (0). The types of carbide which were attacked by the electrolytic chromic acid etch and the alkaline KMnO, etch, Table 11, were identified by X-ray analyses of extracted carbides of five alloys. Carbide residue was obtained from a metallographic specimen by etching the specimen for 24 hr in hydrochloric-picric acid in alcohol (grain-size reagent), after which the carbides, standing in relief, were scraped from the surface of the specimen and mounted on a glass slide. Diffraction patterns were obtained with a Philips spectrometer using iron-filtered cobalt radiation. Figs. 2, 3, 4, and 5 illustrate typical etching behaviors with chromic acid and alkaline KMnO,. Chromic acid attacked Mo,C as shown in Figs. 2(a) and (b)-but not (Fe, Mo),C, Fig. 3(b). Alkaline KMnO, attacked (Fe, Mo),C, Fig. 3(c), and also attacked M0,C. In accordance with these behaviors, a typical differentiation of coexisting Mo,C and (Fe, Mo),~ is shown in Figs. 4(a) and (b). The carbide (Fe, Mo),,C, could not be obtained free of other coexisting carbides for etching experiments. The behavior. however. of coexisting carbides identified by x-ray diffraction as Mo,C ind (Fe, Mo),,C, indicate that (Fe, Mo)23C6 is not etched by chromic

Jan 1, 1961

By A. Taylor

NICKEL-RICH alloys hardened with small additions of titanium and aluminum and centered around that region of face-centered-cubic primary solid solution, 7, where the atomic ratio of nickel chromium is about 3 to 1, form an important series of high temperature materials because of their resistance to oxidation, high temperature strength, and excellent creep characteristics at elevated temperatures.' With suitable heat treatment it is possible to precipitate a phase based on the ordered face-centered-cubic y' phase, Ni,,Al, from the randomly ordered nickel-rich y face-centered-cubic primary solid solution. By adjusting the ratio of aluminum to titanium the precipitation of needles of the hexagonal intermetallic compound n-NiaTi may be effected. In the present investigation, the main interest was focused on the interrelationships among the y, y, and 7 phases. By using alloying elements of high purity and a suitable melting technique the presence of carbides and nitrides could be completely obviated, although it is realized that their presence is probably essential in alloys of commercial importance. As a preliminary to the study of the Ni-Cr-Ti-A1 system, it was necessary to establish the constitutional diagrams of the three contiguous systems, Ni-Cr-Al, Ni-Ti-Al, and Ni-Cr-Ti, which together form the nickel-rich corner of the Ni-Cr-Ti-A1 quaternary tetrahedron. Accounts of this work on the ternary systems have already been published by the author. A preliminary disclosure of the author's investigations on the ternary and quaternary systems has been made by Hignett2 and has since stimulated work in the same field by Nordheim and Grant." Before the detailed account of the quaternary system, a brief description will be given of the three contiguous ternary diagrams on which it is ultimately founded. Ni-Cr-Ti System The 750° and 1000°C temperature isothermals of the Ni-Cr-Ti system as determined by Taylor and Floyd' are shown in Figs. 1 and 2. The single phase fields of greatest interest are occupied by the extensive face-centered-cubic y primary solid solution of chromium and titanium in nickel, and the close-packed-hexagonal Daltonide, n-Ni3Ti, from which tie-lines radiate across the very wide y+n two-phase field. The chromium-rich primary solid solution is represented by a. As may be seen from the diagrams, the extent of the y phase field increases quite appreciably as the temperature is raised from 750" to 1000°C. Isoparametric lines for the y phase are shown in Fig. 1. They are interesting in that they are almost parallel to the y/r+n boundary. Thus the determination of the tie-line directions is entirely dependent on the exact stoichiometry of composition of the 7 phase. Ni-Ti-Al System The 750°C isothermal section of the nickel-rich portion of the system Ni-Ti-A1 as determined by Taylor and Floyd is shown in Fig. 3.' The regions of greatest interest are the extensive y primary solid solution of titanium and aluminum in nickel, the y' Berthollide phase field based on the ordered face-centered-cubic structure of Ni3Al, and the hexagonal Daltonide phase, n-Ni3Ti. As may be seen from Figs. 3 and 4 the area occupied by the y phase is substantially the same at 750°C as at 1000°C, but the area of the 7 phase is considerably greater at the higher temperature. The tie-lines radiate from n-Ni3Ti across the y+v and y' + v two-phase fields and are evenly distributed

Jan 1, 1957

By J. P. Denny

The constitution of the Ga-In system was determined by thermal methods. An experimentally determined metastable equilibrium line (an extension of the indium-rich liquidus) was obtained. The various alloys were studied metallographically using polished samples obtained by a casting method. These low melting alloys required a special dry-ice assembly to maintain a suitable temperature. RECENT interest in alloys that are liquid at room temperature has led to rather extensive investigation of gallium-base alloys. Widely distributed over the earth, gallium could be produced in substantially larger quantities than at present, if a significant demand existed.' One study' has established its presence in 12 out of 14 zinc blends, in all of 15 aluminum ores, in 4 out of 12 manganese ores, in 35 out of 91 iron ores, and in all of 7 magnetite ores. It occurs as a rule in minute amounts, however, leading to high extraction costs. Recent quotations run from $2.50 to $7.50 per g. During the course of the present investigation, portions of the system Ga-In have been redeter-mined, and the results of this study are presented herein. Thermal and metallographic methods have been employed. Lecoq de Boisbaudran, the discoverer of gallium, conducted the first investigation" on Ga-In alloys in 1885. The temperatures of incipient melting, and of completion of melting, were determined at four alloy compositions. In 1936, Hansen' constructed a eutec-tic-type phase diagram for the system Ga-In, based on . work. The existence of a Ga-In compound was regarded as improbable by Hansen, and subsequent investigations are in agreement. French, Saunders, and Ingle3 conducted a more complete study of the system in 1938, using thermal methods. Their phase diagram is a eutectic type, containing a unique concave-upward liquidus. The solid-solution range of gallium in indium was reported as 9.5 pct by weight, and that of indium as less than 1 pct, at the eutectic temperature. The eutectic composition, determined as being bracketed by the compositions showing a true horizontal at the eutectic temperature (16°C), was reported as 76 5-0.5 pct Ga and 24 i 0.5 pct In. Experimental Procedure The preparation of Ga-In alloys is simplified by the low melting points involved. Various compositions were prepared by melting in pyrex tubes, using a cover of distilled water or parafin to prevent the alloys from wetting the glass wall. In all cases, the melts were homogenized. by stirring. Where possible, both cooling and melting curves were determined. The extensive undercooling of gallium was found to prohibit a satisfactory cooling-curve analysis of gallium-rich alloys, however, and transition points on the gallium side of the eutectic could be determined only by melting curves. The inverse rate method of thermal analysis proved to be most satisfactory and was used to a great extent. Various heating and cooling rates were used, ranging from 0.2" to 5.0°C per min. Low temperature melting analyses were conducted within a constant temperature bath, maintained at about 70 °C. The alloys were solidified (under water or paraffin) within a pyrex tube, using dry ice; the tube was then sealed within a cold Dewar flask, the unit transferred into the constant temperature bath, and periodic temperature readings taken. The high temperature melting-curve determinations and all cooling-curve determinations were made in a vertical tube furnace. At near-eutectic compositions, the furnace was placed within a refrigerated room held at —20°C. Accordingly, the furnace on cooling approached —20°C asymptotically and permitted the determination of those phase transitions occurring below room temperatures. Temperatures were measured with a 30-gage iron-constantan thermocouple, immersed directly in the alloy. To prevent contamination of the melt, the leads and junction were coated with Lucite, applied by painting with a solution of Lucite in ethylene dichloride. Electromotive force measurements were made with a Leeds and Northrup precision potentiometer, type 8662. The couples were calibrated against the boiling point. of water and, at lower temperatures, against a calorimeter thermometer having a Bureau of Standards certificate. The melting points of gallium and indium used in the present investigation were determined as 29.-77° and 156.1°C, in good agreement with previously reported values of 29.78°C° and 156.4"C.' The spec-

Jan 1, 1953

By I. W. L. Finlay, H. R. Ogden, R. Jaffee, D. J. Maykuth

Aluminum has been found to be soluble in a titanium to about 26 pct, and to raise the temperature range of transformation from a to 8. Two intermediate phoses exist in the system, a new face-centered tetragonal phase, designated as 7, which occurs between 34 and 46 pct Al, and TiAI Metallographic and X-ray diffraction data were used to determine the diagram. ALUMINUM is one of the useful alloying additions for titanium-base alloys. It is an important constituent in two commercial alloys released in 1950, one containing 4 pct A1 and 4 pct Mn, and the other containing 3 pct A1 and 5 pct Cr as the metallic alloy content. It is probable that, in the future, other titanium alloys containing aluminum will be released. In the course of alloy development work, some of the features of the constitution of titanium-rich Ti-A1 alloys have been developed. These are described in the present paper. The only available information on the Ti-A1 system concerns the aluminum-rich end of the diagram. In summarizing the early work, Hansen' indicated that there is little solubility of titanium in aluminum, and that a two-phase region exists up to the intermediate compound, TiA1a (37.2 wt pct Ti), which has a congruent melting point at 1355°C. Fink' has reported that a peritectic reaction occurs at 665°C between the melt and TiA1³ to form the terminal solid solution of titanium in aluminum. The solubility of titanium in aluminum has been established at 0.24 pct at 510°C and is estimated to be between 1 and 1.5 pct at the peritectic temperature. No information has been published on the diagram above TiAl,, other than a statement- hat aluminum raises the a to ß transformation temperature of titanium. Materials and Preparation of Alloys Iodide-type titanium and high-purity aluminum were used in this investigation. Typical analyses of these materials are given in Table 1. Alloys were prepared by arc melting on a water-cooled copper hearth, using the techniques described previously for contamination-free melting.' Weight losses during melting were very low, ranging from 0 to 0.02 g in a 10 to 15 g charge, indicating that little or no loss of aluminum occurred during melting. This permitted the use of nominal compositions for these alloys. Alloy ingots containing from 0 to 7.5 pct A1 were rolled in air at 850°C to 0.040 in. sheet. Alloys containing from 7.5 to 16 pct A1 could only be rolled about 25 pct reduction at temperatures up to and including 1200°C. Alloys containing above 16 pct A1

Jan 1, 1952

By F. Wald, A. J. Rosenberg

The general features of the constitution of the B-Pt system were determined using standard rnetal-lograph~c, thermoanalytic, and X-ray diffraction techniques. Three compound were found. Two of these, Pt3B and Pt,B, are formed by peritectic reactions at 523° and 890°C, respectively. The third, Pt3B,, is congruently melting with a flat maximum at 940°C but decomposes eutectoidally in to Pt,B ant1 boron nt - 600° to 650°C. THE low-temperature allomorph of boron (red, simple rhombohedra1 a boron) is of scientific and technological interest as an elemental semiconductor.' However, the studies of this material have been hampered by its reported instability above 1200"~ which precludes crystal growth from the melt (mp - 2200°C). Crystallization from platinum solutions has been suggested as an alternative crystal-growth technique, but has met with only limited success.' The technique depends upon the existence of a significant difference between the eutectic temperature and the transformation temperature of boron. In order to clarify the conditions for further crystal-growth experiments, we found it desirable to redetermine the main features of the B-Pt phase diagram since previous reports on the system1'5'6'7 are in marked disagreement. EXPERIMENTAL The experimental methods used were thermal analysis, metallography, X-ray analysis, and, to a lesser extent, measurements of microhardness. Most of the alloys were prepared from spectrograph-ically standardized boron obtained from Johnson-Matthey &Co., Ltd. (212 ppm impurities, exclusive of carbon and oxygen) and platinum powder obtained from F. Bishop & Co. (200 ppm impurities, mainly of other platinum group metals). Some alloys were also prepared with very high-purity, float-zone refined boron (99.9999 pct obtained from "Wacker Chemie" and extrahigh-purity platinum (99.999 pct) obtained from Johnson-Matthey & Co., Ltd. The reported results did not depend on the choices of these starting materials. Five-gram alloy specimens containing 10, 20, 25, 27.5, 30, 33.3, 34, 35, 37, 37.5, 38, 39, 40, 41, 42, 43, 45, 50, 55, 60, 70, and 80 at. pct B were made by melting the elements together in boron nitride crucibles using rf heating of a graphite susceptor, either in vacuum or under high-purity argon. All alloys were heated to at least 1800°C for -5 to 15 min. Most of the alloys did not wet the crucibles when the latter were outgassed by preheating under vacuum. In any event, no weight loss was detected after melting, and the nominal composition was assumed for all specimens. Thermal analysis on 2.5-g samples were carried out in boron-nitride crucibles under a vacuum of 5 x X torr. The apparatus was heated in a "Kan-thal A 1" wound furnace, which limited the maximum temperature to about 1100°C. The output of the indicator thermocouple was fed to a dc recorder with a 1-mv full-scale span and an adjustable zero. The apparatus was calibrated repeatedly, using the freezing points of high-purity aluminum, silver, and gold. The results justified the use of the NBS voltage vs temperature tables for Pt/Pt 10 pct Rh thermocouples. All thermal analyses were run at least twice and both the heating and cooling effects were recorded. Most of the alloys had a very strong tendency to supercool. However, the use of mechanical vibration permitted reproducibility within *5°C for all alloys, except in the region around 40 at. pct B. Only the cooling effects are plotted in Fig. 2, since they appear to be more reliable. For metallography, the alloys were cut with a diamond cutting wheel, cast in a polymethacrylate resin, ground and polished with diamond paste, and etched with dilute aqua regia, a common etch for platinum alloys. Both copper and molybdenum radiation were employed to obtain X-ray diffraction data using Debye-Scherrer cameras and a "Norelco" diffractometer Diffractometry with high scanning speeds (1 deg per min) using nickel filtered CuK, radiation was used to identify the main regions of the diagram. However, molybdenum radiation was used for the detection of boron, since the latter showed very strong absorption and fluorescence effects with CuK, radiation. RESULTS AND DISCUSSION Three intermediate compounds, corresponding to the compositions Pt3B, Pt2B, and Pt3B2, were found in the system. Fig. 1 reproduces their X-ray diffraction spectra, together with those of pure boron and pure platinum. As can be seen from the thermal-analysis data in Fig. 2, Pt3B and Pt2B are formed by

Jan 1, 1965

By Norman L. Newbern, Robert E. Green

An investigation of the effect of size on the deformation properties of metal single crystals made it desirable to grow from the melt cylindrical aluminum single crystals possessing exactly the same crystallographic orientation but varying in diameter. Methods for the growth of rather large (up to 3 in. diam) aluminum single crystals in molds of the desired shape are well known. However, when one applies the same techniques to the growth of smaller (less than 1/8-in. diam) specimens many additional problems arise. Two of the major problems are the construction of the molds to be used and the removal of the thin specimens from these molds without deformation after growth has been completed. Also the problem of the constraint forces exerted by the mold on the specimen is much more pronounced for the smaller specimens. The technique described herein is a zone-melting method in which no mold is used since the surface tension of the molten metal and its oxide is sufficient to retain the melt. The specimen is suspended vertically in a manner similar to that of Keck and Golay.2 However, while Keck and Golay supported the specimen from both ends, the method used here supports the specimen only at the upper end. The surface tension of the molten aluminum and aluminum oxide contains the melt and suspends a length of newly grown crystal that has already passed through the molten zone until the weight of the newly grown crystal is equal to the component of surface tension holding the specimen together in the molten region. When the weight of the newly grown crystal is equal to the component of surface tension holding the specimen together the specimen pulls in two in the molten zone. The length of crystal which can be grown before this separation occurs varies with the diameter of the specimen and the size of the molten zone. In order to prevent the specimen from pulling in two a tube of glycerine is placed beneath the furnace in such a manner that the newly grown crystal passes into the glycerine which provides sufficient buoyancy to allow aluminum single crystals in wire form to be grown to lengths determined only by the length of the tube containing the glycerine. A schematic diagram of the experimental arrangement is shown in Fig. 1. The furnace used is constructed as follows. High-resistance nichrome wire is coiled on a 3/8-in. diam fused quartz tube. The distance between the windings is much less over a length of about 3/8 in. at the center so as to develop a hot spot. This core is located in the center of a 4-in. diam steel cylinder 5 in. in height and insulated from it by Kayolite. The temperature of the furnace is controlled by means of a thermocouple located near the central hot spot and a Minneapolis-Honeywell temperature controller. Temperature ins,ide the furnace is measured with a thermocouple and a standard potentiometer in the usual manner. By the above method it is possible to grow high-purity (99.99 pct Al) aluminum single-crystal wires over a range of sizes. Crystals varying from 1/8 to 1/64-in. diam were grown by the authors. Since the tube containing the glycerine cannot contain a crystal longer than approximately 3 ft, the growth of crystals longer than this presents another problem. It was found that one could cut the newly grown crystal without deformation in the region between furnace and glycerine tube try means of a cutting torch and then by moving the glycerine tube slightly aside continue

Jan 1, 1962

By W. G. Pfann

A simple method of obtaining multistage batch separations by crystallization was described recently. Known as zone-refining, it comprises passing short molten zones through a long solid charge. This technique can now be used on a continuous basis by means of the zone-void method described in this paper. Feed enters, at an intermediate point, a column down which molten zones travel, and waste and product leave at the ends. Materials move in the column through the agency of voids, which are introduced at the ends and travel toward the feed inlet. The voids and molten zones are moved by external heaters in a simple manner, and the principle of reflux is utilized. ANEW method of obtaining multistage separations by crystallization was described recently.' Named zone-refinina.,-, the method comwrises slowly passing a series of molten zones through a long solid charge. Solute becomes concentrated at one or the other end of the charge, depending on whether it raises or lowers the freezing point of the solvent. The separation increases with the number, P, of zone-passes, approaching a limit as P approaches infinity. Zone-refining has been highly effective in purifying germanium and other substances.2,3 and new applications are steadily increasing. Zone-refining is a batch method and as such it has certain limitations inherent in batch operation. If it could be made continuous, its scope and utility would be greatly broadened. This end has been achieved by the zone-void method described in this paper. In the zone-void method feed is introduced continuously at an intermediate point in a column down which molten zones travel, while impure waste and purified product leave at the ends. Both the flows of feed, waste and product, and also the travels of the zones, are actuated by external moving heaters in a simple manner; and the system utilizes the principle of reflux. The method provides, in the field of crystallization, the counterpart of the continuous fractiona-tion column in the field of distillation. The following will be discussed: apparatus and mode of operation, fundamental nature of the separation, design theory, and practical considerations. The method will be described in terms of a binary solute-solvent system in which the solute is an impurity to be removed and the solvent is the desired product. The distribution coefficient, k, defined as the ratio of solute concentration in the solid freezing out of a molten zone to that in the liquid in the zone, is assumed to be constant and less than one. The process is equally effective for k's greater than one and for ternary or higher order systems. Method and Apparatus The essential features of a continuous zone-refining process are represented in highly generalized form in Fig. 1. A series of molten zones, produced by moving heaters, travels slowly down the column or charge (to the left in Fig. 1). If there were no flows of feed, waste, or product, the process would simply be batch zone-refining, the action of the molten zones being to sweep solute down the column, solvent up the column. For the process to be con- tinuous, with stripping and enriching sections in the column, feed must enter, and waste and product must leave, as indicated. The zone-void process accomplishes both objectives, namely, the indicated movements of zones and the indicated flows of material. Zones are moved by moving heaters, just as in batch zone-refining. Materials are made to flow by creating voids at the waste and product exits and causing these voids to move to the feed inlet. Since there must be a net flow of material from the feed inlet to each of the outlets, the indicated movements of voids are in the desired directions, because movement of a void in a given direction corresponds to flow of material in an opposite direction. In order to produce the desired movements of voids, the column is folded into two vertical sections having the feed inlet in common at their upper ends. Voids are displaced upward by the liquids in the molten zones and their travel is actuated by the motions of the zones. Voids travel with the zones in the enriching section and move continuously. Voids travel opposite to the zones in the stripping section and move intermittently. Creation and travel of voids will now be examined in detail. The enriching section of a column in operation, with its void generator, is shown in Fig. 2. The column section is a vertical tube around which a series of closely fitting, regularly spaced heaters travel slowly upward. Each heater produces a molten region, the temperatures of the heaters and the cooling between heaters being controlled so as to maintain the molten zones approximately constant in size. A void is normally present atop the molten zone in each heater. As the heater rises, it continuously melts solid above it, which drips through the void into the molten zone and continuously freezes out solid below it, of concentration k times that of the liquid in the zone. When a molten zone and void reach the feed inlet, which is kept molten, the void is displaced by an equal volume of feed liquid. Generation of voids of controlled size in the enriching section is shown in Fig. 3. The void generator is a tube of small cross-section, provided with lateral heat-conducting fins which sense the position of the heater. Liquid can escape only when the entire outlet tube is within the heater. If any part of the outlet tube is outside the heater, liquid cannot escape,

Jan 1, 1956

By F. W. Glaser

Metal-carbon-boron powder mixtures were hot pressed and the resulting specimens were studied by X-ray diffraction. It was found that regardless of the starting combination of the metal, carbon, or boron powders, a metal boride phase was always the major component in these samples. In the absence of carbon the boride phase formed on hot pressing depended only on the amount of boron present. Two new phases of the system Ti-B were found. They are Ti2B and Ti2B5. The existence of a controversial face-centered cubic phase of formula TiB was confirmed. Electrical resistivities were measured for various boride phases. It was found that the diborides are generally better conductors than the monoborides of the same metal. THE carbides and borides of the transition elements have very high melting points, in the range 2500° to 4000°C, and are therefore of interest as high temperature materials. The literature on the stability or chemical reactivity of these carbides and borides is very scarce. Various investigators'-" have demonstrated a relative instability of certain carbide phases in the presence of boron or boron-containing substances. In a recent publication, Glaserl demonstrated the stability of zirconium-boride (ZrB,) in the presence of carbon at temperatures in excess of approximately 2900°C, while during a preliminary investigation of boride phases, Steinitz' concluded that the diborides are stable in the presence of carbon while the monoborides of the fourth and fifth group are not, forming diborides plus carbides instead. Nelson, Willmore, and Womeldorph" have elaborated on the reaction B,C + 2TiC = 2TiB, + 3C, which was known to occur because of a relative instability of B,C and the great tendency towards TiB, formation at relatively low temperatures (approximately 1200°C). A similar study, involving as starting materials TiO, and B,C and resulting in TiB,, was recently described by Honak4, who observed the beginning of an exothermic reaction of a Ti0,-B,C powder mixture, which, when preheated in a hydrogen atmosphere to approximately 950°C, was carried to about 1600 °C by the heat of reaction. To shed more light on reactions of this type (Metal-C-B), the final product apparently always resulting in a boride phase at the expense of a carbide phase," a systematic investigation was started * Boride phases of various metals, as reported to date, are listed in Table I. and the following is an account of some of the results that were obtained. Materials, Preparation of Samples, Testing Methods The raw materials employed for this work consisted of various carbide, boride, and metal powders. as well as of boron and graphite powders. In cases where commercial grades of carbides were considered unsuitable because of low purity or excessive amounts of graphitic carbon, such carbide powders were prepared by this laboratory. The procedure for the preparation of carbide powders (zirconium carbide, titanium carbide, tantalum carbide, and niobium carbide) consisted of mixing graphite and the respective metal hydride powders in stoichio-metric proportions and subsequent heating of such mixtures in a hydrogen atmosphere in carbon crucibles. The heating was by high frequency to temperatures ranging between 1700" and 2100°C. The resulting carbide was then comminuted and screened to the desired particle size. ZrB, and TiB, powders were produced by the electrolysis of fused salt baths, according to the method described by Andriex.. The borides of niobium, vanadium, tantalum, molybdenum, chro-ium, and iron were obtained by mixing the respective metal and boron powders in the desired proportions. Such metal-boron mixtures were heated in a high frequency furnace to form boride powders. For each metal-carbon-boron group (Tables I1 through XI) a metal, its hydride, carbide or boride were mixed with carbon, boron or boron carbide powders. The additions of carbon, boron or boron carbide powders to any of these metals or metal compounds were calculated to satisfy a particular carbide or boride phase that according to the literature (Table I) had definitely been established by X-ray diffraction work. Samples of powder mixtures were hot pressed in graphite molds that were heated by direct conduction. The specimen dimensions were approximately 2.5X1X1 cm. Hot pressing temperatures were measured optically and maintained for approximately 30 sec under a constant pressure of about 1.3 ton per sq in. Wherever possible, an attempt to obtain maximum specimen density was made by temperature variation. Electrical resistivity testing was done by measuring potentiometrically the voltage drop over a length of 1.5 cm for a current of 10 amp, at room temperature. To obtain electrical resistivities for specific carbide or boride phases, values were plotted as a function of the respective sample densities

Jan 1, 1953

By J. B. Clark

In multiphase ternary diffusion studies, plots of the variation bf the composition on the isotherm constitutes one of the most effective methods of presenting experimental results, especially if such plots are made in a manner which relates the composition path on the isotherm with the diffusion layer structure in the couple. Unfortunately, if different conventions for plotting are used serious misinterpretations occur readily, causing apparent disagreement between investigators who actually share the same viewpoint. A common convention for mapping these diffusion paths is needed at this time because with the increasing use of the electron-probe X-ray microanalyzer, a much greater number of ternary diffusion studies can be expected in the near future. In an effort to prevent unnecessary confusion in the future litera- ture, a convention for these plots is proposed, as outlined below. A hypothetical example of the use of these conventions is given in Fig. 1 where the path of composition through the diffusion structure of the 100 pct A/50 pct B, 50 pct C couple is plotted on the appropriate isotherm of the ABC system. The lower case letters relate the region in the diffusion layer structure to the appropriate composition on the ternary isotherm. 1) The diffusion path is plotted on the isothermal section corresponding to the diffusion temperature of the couple. 2) The terminal compositions of the plotted diffusion path are the initial compositions of the couple halves—provided infinite boundary conditions are maintained. If, in either couple half, infinite conditions are not maintained, then the path terminates at the composition of the exterior surface of the couple. If, at this surface, the composition varies with time or if the plotted path is time dependent, then the diffusion time should be noted beside the plotted path. 3) A solid line crossing a single phase field (e.g., line a-b in Fig. 1) denotes an existing layer of that phase in the diffused couple. 4) A dashed line crossing a two-phase field parallel to the tie lines (e.g., line g-h) represents an interface between the two phases with interfacial compositions designated by the ends of the tie-line. The line represents no spatial extent. 5) A solid line crossing a two-phase field so as to cut tie lines (e.g., line b-c or line j-k) represents a locally equilibrated columnar two-phase layer. The solid line should cut those tie lines which correspond to the lateral interfacial equilibria along the columnar

Jan 1, 1963

By Nicholas J. Grant, Klaus M. Zwilsky

EVER since the unusual high temperature creep resistance and structure stability of SAP (Sintered Aluminum Powder) and similar aluminum-alumina alloys were reported,'," there has been a need to determine whether other metal-metal oxide (or other hard stable particle) alloys, not so ideal as the Al-Al 2 O 3 system, would show similar high temperature strength and stability. Of the many possible methods of obtaining a metal-metal oxide alloy,a one that offers many practical and theoretical advantages is the simple mechanical blending of metal powders with hard stable particles, followed by pressing, sintering, and hot extruding. With this purpose in mind copper powder and silica and alumina were selected for experimentation because these materials are readily available, cheap, reliable, and lend themseives te the simplest processing and testing. Starting Materials—Two sizes of electrolytically deposited copper powders were used, a —200 mesh powder referred to as A powder in this investigation and a —325 mesh powder referred to as C powder. Silica was added in the form of pure Potter's flint from which a —10µ fraction had been separated. Alumina of the a variety was used in two size ranges. The first was a —10µ fraction separated from a coarser aggregate, the second a commercial product of 0.3µ average diam manufactured by Linde Air Products. Preparation of Powders—Five-hundred gram batches of A copper with 1, 3, and 10 volume pct of each of the three oxides mentioned above were prepared, as well as C copper containing 1, 3, and 10 volume pct of —lop silica. Powders were weighed out carefully and blended by ball milling in air for 24 hr. Since this treatment resulted in surface oxidation of the copper, the charge was hydrogen reduced at 260°C for 5 hr. The next step consisted of hydrostatically compacting the powder into a shape suitable for the required hot working. For this purpose a slug about 11/2 in. in diam and 31/2 in. in length was produced by placing the mixed powders into a rubber sleeve, holding in a perforated steel canister, and rubber stoppering at the ends; the assembly was then subjected to a hydrostatic pressure of 50,000 psi. The air was evacuated from the assembly prior to pressing in order to prevent

Jan 1, 1958

By C. S. Smith, L. H. Beck

KNOWLEDGE of the Cu-Zn constitution diagram was critically examined in 1944 by G. V. Ray-nor,1 who suggested the diagram reproduced in Fig. 1 as the best evaluation of available data. No pertinent work on the constitution has been published since that time, although a number of authors have discussed transformation kinetics and theory. Despite the large amount of work that has been done on the constitution of these industrially important and scientifically interesting alloys, minor uncertainties still exist. For example, it is still not possible to say definitely whether a two-phase region exists between the ordered and disordered forms of the 8 phase. A careful re-examination of the phase boundaries in this part of the diagram was therefore undertaken. Two methods were selected for the new investigation—quantitative metallography for the higher temperatures and precision lattice parameter measurement for lower temperatures. Because of the relatively narrow two-phase regions flanking the ß phase in these alloys, quantitative metallography is particularly suited for their examination, since the relative amounts of the two phases are very sensitive to their compositions. The method, however, is useless below about 350°C because of the inadequate resolution of the two constituents. Below 400°, however, the X-ray diffraction method is applicable, although it is of somewhat lower sensitivity in this system. The changes of composition that occur during quenching from above about 500°C entirely vitiate X-ray measurements at room temperature though they do not affect metallographic area measurements. The two methods overlap and supplement each other admirably. Both methods depend on the attainment of equilibrium composition of the two phases in a more or less intimate mixture and thus avoid the difficult problems of nucleation and long range diffusion involved in the conventional metallographic bracketing method. The alloys were melted from a master alloy made from re-electrolyzed cathode copper and Horsehead 99.99 pct Zn. Melting was done under a cover of either borax or charcoal and the alloys cast into a 7/8 in. sq graphite mold for the a-ß alloys or a 3/8 in. diam cylindrical graphite mold for the ß-? alloys. The a-ß alloys were rolled at 750°C to 5/8 in. sq; annealed for 24 hr at 800°C and quenched; then rolled and swaged at 200°C to 3/8 in. diam rods, annealed 24 hr at 200°C, quenched and cold rolled 2 pct reduction. This treatment was intended to obtain a small grain size and to produce many nuclei of the minor phase for growth on subsequent heat treatment. The unworkable ß-? alloys were given preliminary treatment by sealing in Vycor tubes in vacuum and annealing for 4 hr at 800°C followed by cooling in air. Samples of homogenized alloys were checked spectrographically for impurities, but the principal components were determined on samples subsequent to heat treatment. The impurities analyzed averaged approximately as follows: Ag, 0.0002 pct; Fe, 0.004; Si, 0.0008; Cd, 0.005; Mg, 0.0002; and Pb, 0.002. For metallography, samples of appropriate composition were cut into rods 5/8 in. long, sealed in pyrex tubes in vacuum and annealed for eight weeks at temperatures of 470°C and below, two weeks at 480°, 500°, and 600°C, and 4 hr at 700°C, followed by quenching in cold water. Temperatures were accurate to ±2°C. The cylinders were then machined to 8.7 mm diam and a slice weighing 1.5 g cut with a thin saw transversely from the center of each. This

Jan 1, 1953

By C. Dean Starr

The physical basis of the equation correlating electrical conductizlity and temperature coefficient of resistance of solid solution alloys has been inzlestzgated and the nature of the constants evaluated. It is shaun that the same form of correlation is valid irrespective of the magnitude of the temperature coefficient. However, the effect of therma1 expansion and change in resistivity with temberature nust be considered when the magnitude of the temperature coefficient of resistance is near zero. In a comprehensive literature survey conducted at the Armour Research Foundation in 1950, it was found that a linear relationship exists between the electrical conductivity, K, and the temperature coefficient of resistance, a, for solid solution alloys. This was expressed by the equation where B, a constant, depends on the solvent metal but not the solute. A continuing investigation by Hansen, Johnston, and Parks showed this equation was generally appropriate for Cu, Ag, Au, Pd, Pt, and Co base binary solid solution alloys as well as for many ternary alloys of copper over a range of conductivities and temperature coefficient of resistances from 0.02 to 0.60 reciprocal pohm cm and-0.00015to0.004Q per 0 per "C respectively. Eq. [I] was not always valid for alloys that exhibited a change in state (magnetic to nonmagnetic) or for alloys that had a temperature coefficient of resistance near or below zero. For example, in nickel alloys, a simple linear curve as predicted by Eq. [l] was not obtained when the conductivity was plotted against the temperature coefficient of resistance. Hansen suggested that deviations observed were caused by transitions from a ferromagnetic to a nonmagnetic state. Subsequent and more extensive data by ronin on Ni-Mn alloys confirmed Hansen's postulate. While both states independently showed a linear relationship between K and a, the value of B was different for the two states. In some copper and gold base alloys, as well as the platinum and palladium alloys investigated by Hansen, the conductivity did not extrapolate to zero at zero a as demanded by Eq. [I]. This deviation can be readily corrected by simply adding a constant to Eq. [I.] whence Eq. [2] shows the K decreases as a decreases but that K has a positive value when a = 0 which is observed for commercial solid solution alloys as well as the experimental alloys tested by Hansen. While other methods of correlation of electrical properties have been made such as the one by Starr and Wang3 who found a linear relationship between resistivity and temperature coefficient of resistance for Ni-Cr-Al-Cu alloys, the data, in general, can also be correlated by a form of Eq. [2]. Thus, Hansen's empirical equation has considerable merit. The objective of this paper is to determine the physical basis for this equation and to examine the region near zero a in more detail. ELECTRICAL CONDUCTIVITY VS TEMPERATURE COEFFICIENT OF FU3SISTANCE The resistance of a metal or alloy is defined as

Jan 1, 1963

By E. J. Ripling, M. W. Toaz

Tensile tests were conducted on pure magnesium and on four commercial alloys over a variety of temperatures and strain rates. The high positive slope of the ductility vs testing temperature curves that is found over a short range of testing temperatures for these materaturerials was shown to result from the fact that the microstructure was not stable at these testing temperatures. Pure magnesium did not display a transition temperature, although its sub-room temperature ductility was low. This poor ductility resulted from a grain boundary weakness. The aluminum-bearing commercial magnesium alloys had a higher ductility than the pure magnesium. ness.Thealuminum-bearingcommercialThese alloys did exhibit a transition temperature and grain boundaries that were stronger than the grain material. Both pure magnesium and the commercial alloys began initiating cracks at strains equal to one half of their fracture strain. MAGNESIUM base alloys' enormous potential as structural materials lies in their high strength to weight ratios. At present, the high strength magnesium base alloys such as AZ-80, which will be discussed later, have about as high a tensile strength to specific gravity ratio as the highest strength wrought aluminum alloy, 75s-T6, and, of course, a much higher strength to weight ratio than structural steel. Further, since the magnesium base alloys develop their high strength to weight ratios with moderate strengths and extremely light weights, the ratio of load carrying capacity to the weight of many structures is relatively higher for the magnesium base alloys than their strength to weight ratios would indicate. This results because judicious increases in section size, such as increasing the depth of bending members or adding reinforcing ribs, can frequently increase the weight of a structure linearly while the strength and stiffness increase as the second or third power of the added weight. Strength and rigidity must be designed into lightweight structures by those techniques which establish multiaxial stress states. Consequently, strong, lightweight structures frequently also possess a greater propensity toward brittle failures. In order to insure against these catastrophic failures, an extra premium must be placed on ductility and toughness in light alloys. Current knowledge of the ductility and toughness behaviors—notched behaviors—of magnesium base alloys is limited.* Most of the magnesium base alloys * The state of present knowledge regarding the effect of testing temperature on mechanical properties has recently been summar-ized by Pritchard.' crystallize in the hexagonal system, so that they are expected to exhibit a tough and ductile to brittle transition temperature. Actually, a transition temperature behavior has been reported for commercially pure magnesium in the literature, but the characteristics of this transition temperatureh uggest that it may not be a transition in the usual meaning, but simply the onset of some thermal softening, a performance much like that which face-centered-cubic lead might exhibit slightly below room temperature. If transition temperatures do exist, such important questions as the manner in which they are affected by internal variables such as chemical composition and grain size, or the effect of external variables such as rate of straining or notch severity have never been investigated. The investigation reported upon herein was undertaken in order to define some of the mechanical behaviors of the magnesium base alloys better, to gain a better understanding of the influence of some of the above listed variables, and particularly to understand their effect on ductility and toughness better. Material and Procedure Material-—Pure magnesium and four commercial alloys were used in this investigation. The alloys were selected so that chemically they made up a series with approximately the same minor alloying

Jan 1, 1957

By A. J. Griest, P. D. Frost, J. R. Doig

During the past 5 years, research directed toward the development of titanium alloys having improved strength-ductility relationships and heat treatability has been carried out at Battelle for the U. S. Air Force.1"3 In the course of this work, a method of heat treating ß-stabilized titanium alloys was developed which produced a wide range of useful properties.4 The heat treatment consisted of two steps: a) solution treating at temperatures in the a-ß phase region, and b) overaging at a lower temperature in the range 800°to 1100°F. Corollary to the alloy development work, research was conducted on the mechanism of the heat-treatment reaction. The investigations of Frost and co-workers on isothermal transformation in Ti-Cr5 and Ti-Mn8 alloys disclosed the existence of the transition phase, w, during the course of the decomposition of metastable ß phase. Subsequent work at Battelle7,8 'and at Case Institute by Brotzen and co-workerss further clarified the nature of the decomposition process. Beta decomposition was found to proceed by the following series of reactions: 1 2 3 4 a + Ti, My (in eutectoid systems). ßo, ßr, and ßU refer to ß phase of original, enriched, and ultimate alloy contents, respectively. Omega is a transition phase having a complex structure. 10-13 Step 4, of course, occurs only in ß-eutectoid systems. This paper presents data correlating transformation behavior with mechanical properties for the following alloys: Ti-8Mn, Ti-8Mn-2A1, Ti-4Mn-4A1, Ti-6Al-4V, and Ti-4Fe. The isothermal decomposition of ß in titanium-manganese alloys of similar composition has been investigated by Frost and coworkers8 and the effect of various annealing treatments on alloys in this system has been studied by Holden, Ogden, and Jaffee.14 The compositions Ti-8Mn-2Al, Ti-4Mn-4A1, and Ti-6A1-4V, were studied in the present work in an effort to define more clearly the effect of aluminum on the response to solution and aging treatments. Ogden, Holden, and Jaffee15 have invesitgated the effect of aluminum on the response of a similar alloy (Ti-8.8Mn-2.46A1) to annealing treatments, and Luini and Lee16 have made an exploratory investigation of the heat-treatability of the Ti-4Mn-4Al alloy. The Ti-4Fe alloy was studied as an example of a moderate1y active eutectoid system. Holden, Ogden, and Jaffee 17 have studied Ti-Fe alloys and have presented some hardness data for aging at 400°C for alloys of Ti-2.56, 5.01, and 7.35 iron after quenching from the a-ß field (750°C). EXPERIMENTAL PROCEDURES The experimental procedures generally used in the precipitation-hardening study are outlined in the following sections. Departures from these techniques are noted in the discussions of the individual alloys. Table I presents the nominal and actual compositions of the alloys studied, together with the swaging and rolling temperatures. In all cases, these temperatures were in the a-ß field and the microstructures consisted of an equiaxed a-ß mixture. Melting and Fabrication—Except for the commer-

Jan 1, 1960