Search Documents

By G. R. Wilms

A study has been made of the structural changes in polycrystalline high purity aluminum during the tertiary stage of creep under conditions of constant tensile load. It appears that there is no basic modification in the particular mechanism of deformation that characterized the preceding secondary stage of creep, but that the changes in crystalline structure produced during the tertiary stage are only a consequence and not a cause of the accelerated strain. Intercrystalline fissures were observed on entry into the tertiary stage, and these might supplement the accelerated rate of strain owing to local stress concentrations. There is evidence that the formation of these fissures may be associated with the presence of surface imperfections, and it is suggested that a more generalized treatment of the results may explain certain creep characteristics of commercial alloys. IN previous work'-4 a study was made of the changes produced when specimens of annealed aluminum were deformed at various temperatures and rates of strain, especially under conditions leading to creep under constant tensile load. It was shown that, as the temperature was increased or as the rate of strain was decreased, elements of the substructure produced within the grains became coarser, and with the strain rate constant at a given temperature, their size tended to an equilibrium value. The preliminary process of the breaking down of the grains into a substructure was identified with primary creep.' The subsequent equilibrium, condition was associated with secondary creep. The question then arose whether the tertiary stage corresponded to any further significant change in the substructure. The question is also of interest in view of the opinion, expressed for instance by Andrade,5 that the tertiary stage is merely an accelerated rate of strain due to the reduced area of section of a specimen under continuous tensile load, and the other opinion, as suggested by the observation by Sully, Cale, and Willoughby6 of a tertiary stage in com-pressive loading, that this third stage is a real effect in its own right. The object of this paper is to record some observations on the tertiary stage of high purity aluminum. Experimental Procedure The material was aluminum of 99.98 pct purity as previously used. The specimens had a rectangular section of l/8 x l/2 in., and extensions were measured over a 1 in. gage length. After machining to shape, the specimens were annealed to give a standard grain size of 0.2 mm and then electropolished. The general procedure involved metallographic and X-ray diffraction examination at progressive stages of elongation (marked by arrows on the curves shown in Figs. 1 and 2), the specimen being extended to fracture under constant load at a given temperature. The X-ray tests were made by the back-reflection method from a stationary specimen, using CoK radiation. The longer edge of the micrographs in the paper corresponds to the direction of applied stress. Results The previous work showed that, in the secondary stage of creep in aluminum, three basic types of structure could be developed according to the temperature and rate of strain. These were: 1—slip, which predominated at the lower temperatures and higher rates of strain and produced the finest and least perfect substructure; 2—cell structure, which superseded slip as the temperature was raised and the rate of strain decreased and which was characterized by a coarser and more perfect structure and an absence of slip lines; and 3—a stage termed "boundary microflow," which predominated at still higher temperatures and lower rates of strain when the cell size had increased and become comparable

Jan 1, 1955

By E. H. Edwards, J. Washburn, E. R. Parker

The mechanism of strain hardening was discussed in connection with some recent observations on the stress-induced motion of dislocation boundaries and on the simple shear deformation of zinc, cadmium, and copper crystals. THE nature of work hardening accompanying plastic deformation of metals has long been the subject of speculation. As early as 1925, Becker' suggested a thermodynamic process to explain slip based on the statistical probability for the occurrence of local glide steps. The theory that plastic glide was due to the presence of lattice defects known as dislocations was first introduced in 1934 by Taylor: and Orowan, and Polanyi.4 Taylor presented a rather complete analysis of the behavior and interaction of dislocations. He assumed a certain type of stress field to be associated with a single dislocation, and postulated that work hardening would result from plastic flow in two ways. First, dislocations following one another across a slip plane might encounter a barrier which would impede their movement, thereby gradually diminishing and eventually stopping plastic flow on that plane. The second mechanism involved the concept of dislocations traveling in opposite directions on nearby planes attracting one another to form a meta-stable lattice. The interaction of dislocations in such an array was shown to be large enough to require an increase in stress before plastic flow would continue. Kochendorfer5,6 extended the concept of work hardening involving a back stress due to an accumulation of like dislocations on a slip plane. He suggested that the formation of a new dislocation is hindered by those dislocations already present. The hardening resulting from the interaction of newly forming dislocations with bound dislocations was designated as "formative hardening," and indicated to be the only type of hardening necessarily connected with the slip process. In another detailed picture of work hardening, Mott and Nabarro7 assumed that sufficient dislocations are primarily present in the crystal as a consequence of growth irregularities (mosaic structure) to initiate slip. Work hardening resulted from the interaction of migrating dislocations with localized internal stresses produced during deformation. More recently, however, Mott8 as modified his treatment to include the generation of dislocations at Frank-Read sources and he accounts for the hardening by the formation of sessile dislocations. It has been widely accepted that metals of hexagonal structure, usually possessing only one set of glide planes, exhibit mechanical behavior markedly different from those having cubic structures. However, the differences in behavior of the two classes may be less fundamental than suggested. Rohm and Kochendorfer9 have shown that a single crystal of aluminum subjected to approximately simple shear gives the type of stress-strain curve associated with the hexagonal metals. Similar behavior has been demonstrated for gold and silver crystals by Andrade and Henderson.'" Thus when glide in cubic metals is restricted to one plane, the strain hardening characteristics closely resemble those of the hexagonal metals. It would appear, therefore, that an investigation of some of the strain hardening properties of single crystals sheared in simple glide might provide a more complete understanding of the phenomenon of work hardening. This report relates a number of recent observations made on single crystals of copper, zinc, and cadmium tested in simple shear. In addition, pertinent observations of effects accompanying stress-induced movement of dislocation boundaries are reported. Experimental Procedure and Results Details of the production and advantages of the type of single-crystal shear specimen employed for the following tests have been presented in a previous publication.n The method of testing makes

Jan 1, 1954

By Martin Epner, Eric Gregory

DURING the past decade, considerable work has been carried out on various cermet systems in an effort to produce materials suitable for high-temperature applications in gas turbines. Most of the materials have not, as yet, met the requirements of the engine manufacturers, primarily because of their lack of room-temperature ductility and thermal shock resistance. In the field of tool materials, however, although ductility is still of prime importance, much has been accomplished by improving design parameters and the quality of carbide materials with a view to using cermet compositions successfully. The systems described in this paper were designed primarily for application in this field, although their development was a natural outcome of work on similar compositions designed for high-temperature service. In steel-bonded titanium carbide, the steel binder imparts heat treatability to the system while the carbide provides abrasion and wear resistance. Combining the carbide and the steel matrix in carefully controlled proportions results in a composite material which, when the steel is hardened, has man of the properties of cemented tungsten carbide. In the annealed condition, this material can be readily machined by the conventional chip-removal techniques. Titanium carbide has certain distinct advantages over many of the other carbides when combined with a steel matrix. It is among the hardest of the carbides and is one of the most stable. Liquid iron wets titanium carbide, and this wetting assists in the formation of a dense cermet. Once the composite structure has been formed, the titanium carbide acts as a relatively inert phase during the heat treatment of the matrix. PREPARATION OF ALLOYS The steel-bonded titanium-carbide materials described in this paper were prepared by the liquid-phase sintering technique. The titanium carbide used had an average particle size of 6 to 7 p, a total carbon content of 19.4 pct and 0.35 pct free carbon. This was blended with the elemental metal powders by ball milling them together in a hexane medium. After drying, paraffin wax was added to the blend to provide green strength in the pressed briquettes, and compacting was performed at 15 tsi. Liquid-phase sintering was carried out in vacuum at temperatures which depended on the chemical composition of the system involved, but which were usually around 2640° F. The resultant materials had a density approaching 100 pct of theoretical. The

Jan 1, 1961

By Webster Hodge

MALL generators and motors are required to Soperate, in some critical applications, at temperatures where cold-worked silver-bearing copper re-crystallizes. Copper containing up to 30 oz Ag per ton has been used for many years to build the highest grades of commutators and slip rings. With failure of commutators impending because silver-bearing copper cannot withstand the stresses imposed at these higher temperatures, Cr-Cu was tried as a substitute with varying degrees of success. Cr-Cu proved difficult to fabricate because a critical heat treatment was necessary to obtain sufficient ductility. Besides, its rupture strength was shown to be low at operating temperatures, its electrical conductivity lower than desired, and its cost high. Furthermore, it often contained hidden flaws. The Nippert Electric Products Co. set out to find a better material by undertaking a research project with the stated objective of providing a material suitable for commutators that would have 1) a softening temperature above 750°F (400°C), 2) a minimum electrical conductivity of 90 pct of that of pure copper, 3) a strength not less that that of cold-worked silver-bearing copper, and 4) a materials cost of not over 1.5 times the cost of copper containing 25 to 30 oz Ag per ton. No commercial alloy met these specifications. However, it was found that copper containing from 0.18 to 0.35 pct Zr could be produced quite easily in the laboratory, and promised to fulfill the major requirements noted above. Interest naturally centered in the lower part of this composition range, since such alloys gave somewhat better electrical conductivities, and were lower in

Jan 1, 1958

By C. Y. Ang, C. Wert

Quench aging of supersaturated solid solutions of nitrogen in columbium takes place in reasonable times in the temperature range 300&apos; to 500°C. Changes in internal friction, hardness, and electrical resistivity are found to accompany this change. THERE is practically no detailed information in the literature concerning interstitial solid solutions in either columbium or tantalum. The fact that both of these metals are used extensively commercially in both pure and alloyed states makes studies of their properties of value. While the plan is to study both these metals and their alloys extensively, so far only a small number of measurements have been made. This paper presents data obtained in the initial investigations of columbium. The principal interstitial impurities of columbium are likely to be hydrogen, carbon, oxygen, and nitrogen. The first of these, hydrogen, is outside the scope of internal friction measurements at present and nothing quantitative is known about the initial hydrogen content of the specimens. However, it is believed that it is completely absent after the preliminary heat treatments are carried out. The carbon content of the original samples is low and can be reduced still further during sample preparation. Oxygen is normally present to some extent in columbium and can also be added or removed easily. Nitrogen is also normally present in small amounts and can also be controlled within limits. Since it is not possible yet to remove all the nitrogen from columbium and since it is possible to remove essentially all the oxygen and carbon, initial measurements were made on the alloy system nitrogen in columbium. In this sense then, the alloys are true binary alloys. Little is known about the effects of nitrogen on the physical and metallurgical properties of columbium, so it was necessary to perform some rather elementary measurements on the specimens. These measurements are described briefly in the next section and are discussed in detail in later sections. Scope of the Work That internal friction is associated with diffusion of nitrogen in columbium has been known for some time. It is similar in nature to that for carbon and nitrogen in a-iron. In these latter cases, the information obtained from internal friction has been useful metallurgically.&apos; and it is not too much to expect useful information from similar studies on columbium containing nitrogen. The technique of internal friction measurements is adequately described by Ke2 At a frequency of 1 cps the internal friction peak for nitrogen in columbium occurs at 300°C and that for oxygen at 160°C." So that all the measurements will be meaningful metallurgically, the internal friction has been calibrated by making a measurement of the damping at the two peaks and a measurement of oxygen and nitrogen content by chemical analysis. A comparison of the two gives the following calibration factor: To go from damping capacity expressed in terms of 1/Q to weight percent of oxygen and nitrogen in solid solution in columbium, multiply the peak values of internal friction by about 4 and 3 respectively." Data from which these factors were calculated are presented in Table I. The increase of electrical resistance of columbium caused by the addition of oxygen and nitrogen as interstitial impurities has been quantitatively determined. At room temperature the percentage increase is small for small additions of impurities (<0.1 wt pct); as the temperature is lowered it becomes an increasingly larger factor of the total resistance. An empirical relation has been established to express the resistivity at — 195°C in terms of weight percent of oxygen and nitrogen in solid solution. It is easy to make supersaturated solid solutions of nitrogen in columbium and to observe aging phenomena. The optimum aging temperature, as in the case for carbon and nitrogen in a-iron, occurs at the temperature for which the time necessary for a single place-change in diffusion is about 1 to 10 millisec. This means for nitrogen in columbium that significant property changes should take place for this alloy at about 400" to 500°C in reasonable time intervals. Results of such aging experiments are

Jan 1, 1954

By J. A. Hren, C. M. Wayman

RECENT investigators have noted anomalous behavior in the electrical resistivity of vanadium below room temperature. Rostoker and Yamamoto1 in studying the vanadium-oxygen system hypothesized that the body-centered-tetragonal phase existing from 15 to 34 at. pet O at approximately 800°K was really a low-temperature allotrope of vanadium that was stabilized by oxygen. In measuring the electrical resistance of cold-swaged vanadium rod over a range of temperatures, a small discontinuity was observed at approximately 240°K, supporting their notion of allotropy. However, the magnitude of the observed discontinuity was extremely small. Loomis and Carlson2 in studying the ductile-brittle transition in vanadium also made resistance measurements and reported a discontinuity near 200°K. More recently, White and Woods3 showed that the electrical resistivity from room temperature to approximately 100 °K was not linear and at variance with the Bloch-Griineisen law. Instead of finding a discontinuity, they observed a deviation from linearity below 200°K. In discussing their results they pointed

Jan 1, 1961

By G. F. Bolling

STUDIES of grain boundary migration in zone-refined metals have all shown that the rate of migration is greatly reduced by small added solute concentrations. However, it is apparent that a difference exists between boundary migration during normal grain growth and single boundaries migrating in a bicrystal to consume a substructure. To effect the same reduction in velocity in the two cases, much more solute is required for grain growth than for the single boundary experiments. One case is available for direct comparison; both Bolling and winegardl and Aust and utter&apos; added silver and gold to zone-refined lead to study grain growth and single boundary migration, respectively. For comparable reductions in migration rates, about 500 times more solute was required to retard grain growth than to retard the single boundaries. A reason for this difference is suggested here. The rate of grain boundary migration is dependent on solute concentration and must therefore also depend on the solute distribution; i.e., regions of higher solute concentration encountered by a moving boundary must produce greater retardation and thus could determine any observed rate. A dislocation substructure can be the source of a nonuniform solute distribution since it can attract an excess concentration of certain solutes. In fact, it is probable that the solutes which impede grain boundary migration most would segregate most severely to a substructure for the same reasons. Thus a dislocation substructure present in a crystal being consumed could locally magnify the concentration of solute confronting an advancing grain boundary. In the single boundary experiments a low-angle substructure, within single crystals obtained by growth from the melt, was used to provide the driving force to move a grain boundary; in grain growth, no substructure of this magnitude was present. The increased solute concentration at subboundaries should be given approximately by C, = G e c,/kT, where t, is a binding energy and CO the bulk concentration. To account for the difference between the two experiments in the Pb-Ag and Pb-Au cases, C, must be the concentration impeding the single boundary migration, and a value of t, = 0.25 ev is necessary. This is reasonable, even though calculation on a purely elastic basis gives t, = 0.12 ev. because electronic effects must enter for silver and gold in lead. The compound AuPbz forms3 and the metastable compound AgrPb has been reported to nucleate at dislocations prior to the formation of the stable, silver-rich phase.4 Other observations support the hypothesis that a magnified solute concentration impedes the single boundary migration. For example, some crystals were grown by Aust and Rutter at concentrations of ~ 0.1 wt pct Sn and 2 x X at. pct Ag or Au which exhibited a cellular substructure, and in these crystals no boundary migration was observed. It is therefore evident that the higher concentrations at cell boundaries drastically inhibited migration. Inclusions would not have been responsible for this inhibition since according to recent work on cellular segregation,5 no second phase should have occurred in the segregated regions at the cell boundaries for the conditions of growth used, at least in the Pb-Sn system. In the purest lead, only the "special" boundaries observed by Aust and Rutter gave rise to the same activation energy as that obtained in grain growth. It is reasonable to suppose that the structure of special boundaries does not favor segregation at low concentrations and thus solute, or an inhomogeneity in its distribution, would have no effect. Random boundaries, on the other hand, are affected by solute and the substructure would enhance residual concentrations in the zone-refined lead, leading to a higher activation energy. It is clear, even without a detailed theory, that the apparent activation energies and exact solute dependence in the two experiments must be different as long as the non-uniform solute distribution produced by the substructure is important. Recrystallization experiments should also be susceptible to the same kind of local segregation at subboundaries or disloca tion cell walls; a suggestion similar to this has been made by Leslie et al.&apos; Following the arguments presented here, the effects of a given solute concentration would be like those observed by Aust and Rutter if segregation occurred, and like those of grain growth otherwise. This work was partially supported by the Air Force Office of Scientific Research; Contract AF-49(638)-1029.

Jan 1, 1962

By S. Storchheim

MORE and more attention is being paid to the bonding of metals in their solid states. For a better understanding of this technique for joining metals and how it is affected by changes in temperature, pressure, and time at temperature and pressure, a detailed report concerning nickel to aluminum bonding has been published.&apos; In order to broaden the knowledge accrued, some additional work concerning solid state joining of aluminum to copper and aluminum to zirconium was performed. The investigation of the Al-Cu system was considerably more extensive than the investigation of the Al-Zr system. For the A1-Cu system, not only were tensile sudies made but intermetallic penetration rate investigations also were carried out. The effect of temperature on intermetallic penetration rate for the A1-Cu system was determined at 11 tsi pressure, held 2 min. Procedure Apparatus: The hot pressing technique was the means of solid state reaction used and required the equipment depicted in Fig. 1. The following procedure was involved: The two metals to be reacted were placed in an aquadag-lubricated 18-4-1 tool steel die, 16 in. high by 1.440 in. ID, between punches of 1.366 in. diam made of the same material. A thermocouple well was located in the die body 3½ in. down from the top of the die, while another well was located centrally in the bottom punch 8½ in. from the bottom of the die. This die assembly was located in three cylindrical ceramic heating furnaces placed in tandem. Each furnace was controlled individually by a Variac power transformer. In turn, the die and furnaces were placed in a water-cooled stainless steel pot which could be evacuated. A cover, which contained a centrally located Wilson seal with an 18-4-1 1 in. diam ram running through it, was bolted on the pot. After sealing, the pot was evacuated by a roughing pump to 200 microns pressure, after which a diffusion pump was used to bring the pressure down to 5 to 15 u. At this pressure, the furnaces were turned on. As soon as they started to heat, out-gassing of the entire unit raised the pressure to 30 to 400 p. By the time the specimens were at temperature ready to be pressed, approximately 4/2 hr, the vacuum pumps had re-established the 5 to 15 u pressure. Once the desired temperature was reached, the required pressure was applied for a predetermined length of time to the 1 in. ram, through to the top punch, and to the specimen. When the time for keeping the specimen under pressure had elapsed, the pressure was released, the energizing coil current turned off, and the assembly allowed to cool. After cooling, the die was removed from the pot and the specimen was ejected. Specimen Preparation: Two different types of specimens were made for this investigation. One was for subsequent tensile testing, while the other was for determination of intermetallic alloy zone penetration into the parent metals. Tensile Bars—Commercially rolled copper pieces in. thick or zirconium sheet pieces 1/32 in. thick and 1.366 in. diam were placed between commercial 2-S aluminum rod 1 in. thick and 1.366 in. diam. This sandwich in turn was slipped into a 2-S aluminum sleeve 1.438 in. OD and 1.370 in. ID. This sleeve lined the couple up and prevented the aquadag lubricant from getting in between either the A1-Cu or Al-Zr interfaces. Immediately prior to the specimen assembly, the copper or zirconium was abraded on the flat surfaces with 320 grit silicon carbide paper, producing clean smooth surfaces. The aluminum was chemically cleaned just before assembly by: l—degrease in acetone, 2—distilled water rinse, 3—immersion for 3 min in 5 pct NaOH at 70" to 80°C, 4—distilled water rinse, 5—immersion for 2 min in 50 pct HNO3 solution at room temperature, 6—distilled water rinse, and 7—drying in a blast of gas. After the A1-Cu sandwiches were hot pressed and ejected, the specimens were machined such that the aluminum sleeve was removed, and the remaining aluminum was then threaded; the bar so produced was tested later for tensile strength. In all the instances where Al-Cu couples were tested, the specimens broke during the test at the Cu-A1 interface and never within the aluminum or copper. The ultimate tensile strength values at times showed considerable scatter for a set of given reaction conditions. Because of this, as many as three to five specimens were made for a particular set of conditions. The trend of the average tensile strengths obtained was not as conclusive as was the trend of the maximum tensile strengths, the latter values being obtained under optimum reaction conditions. Therefore, the values of ultimate tensile strength given herein are maximums.

Jan 1, 1956

By Richard Borg

The partial molal free energy of Cd in each of the four intermediate phases, Cd3 Cu, Cd8 Cu5, Cd3Cu4, and CdCu2 is determined using the Knudsen vapor pressure technique. Measurements are made also within the two-phase regions, and thus the variation in FCd is now known across the entire phase diagram. The absolute values are all less the 2.0 kcal and increase regularly with increasing Cd concentration. The small absolute value of the free energy precludes the possibility of obtaining highly accurate values; nevertheless, the results are compatible with those previously reported for the liquid phase. Additional results are reported concerning the lattice parameters of the 6, E, and b phases. THE elements Cu and Cd combine to form four intermediate phases which are designated* and E and which include respectively the following inter metallic compounds: CdCu2, Cd3Cu4, Cd3 Cu5, and Cd3 Cu. The extent of each phase with respect to temperature and composition is shown in Fig. 1 which is the equilibrium diagram drawn according to Hansen.1 All four phases are brittle, and most probably are true intermetallic compounds. Only the crystal structure of the 6 phase has been thoroughly investigated.2,3 The structure is cubic and isotypic with y brass. The structure of Cd3 Cu has not been previously reported, It is hexagonal with a = 8.11 and c = 8.76 0.02Å and the structure is presently being determined.* The compounds Cd3 Cu4 and CdCu, have been each previously the subject of a single investigation. Cd3Cu, is presumed to be cubic4 with the space group Fd3m, whereas CdCu2 is hexagonal2 with the C14-type structure. Cu2 Cd is found by X-ray analysis to be hexagonat with lattice parameters a = 5.00A and c = 16.17Å. The material appears to be pure Cu2Cd as all reflections could be indexed on the basis of the single hexagonal structure. These values disagree with those of Kripyakevich and coworkers5 who report a = 4.96Å and c = 7.98Å. Their investi-

Jan 1, 1962

By E. F. Ketterer, D. B. Collyer, A. B. Wilder

AISI constructional alloy steels are a series of steels in which a numbering system signifies the chemical composition limits. SAE (Society of Automotive Engineers) and AISI (American Iron and Steel Institute) use basically the same numbering system. The steels contain, in part, alloy additions of chromium, molybdenum, nickel, and vanadium. They are used widely in the automotive industry but have not been adopted for high temperature service. The purpose of this investigation was to study changes in microstructure observed in typical AISI constructional alloy steels in the welded and un-welded conditions after exposure for 34,000 hr at 900" and 1050" and, in several instances, 1200°F. The tensile and creep rupture properties after exposure for 10,000 hr were also evaluated. The investigation is a continuation of the work previously discussed. Little was known concerning the existence of graphite in medium or low carbon steels before 1943. It is important to note that continued exposure at elevated temperature is required in order to develop graphite in steels. Interest in the presence of graphite in steel, and also in changes in the properties of steels after long service at elevated temperatures, developed after 1943 when a failure of a welded joint of high temperature piping was associated with the graphitization of a relatively low carbon content steel with 0.50 pct Mo,8,0 Numerous investigations have beeen made in recent years studying the relationship of this type of failure to changes in properties. Attempts have been made to evaluate the performance of a number of steels, particularly in the heat-affected zone of welds. It was the unfortunate failure of a weld-heated zone in high temperature piping in the steam-power industry which focused attention upon possible failures, and upon the need for improved steels for high temperature piping service. Investigation by the National Tube Div., U. S. Steel Corp., Lorain Works, has included a wide variety of steels in an attempt to learn the effects of numerous factors and elements upon the long time performance of steels, although many of the compositions studied will never be used at elevated temperatures.1,4-7 Included were the well established AISI steel series, which offered opportunity to test moderately high carbon content steels as well as observe the effect of nickel, chromium, molybdenum, etc., upon the properties of these well known steels. The properties of the AISI steels were also studied for comparison with the previously reported properties of the Cr-Mo steels, now used by the steam-power industry.5,7 Materials and Testing Procedure The AISI alloy steels in Table I were exposed for 10,000 and 34,000 hr at 900°, 1050°, and 1200°F.

Jan 1, 1958

By P. G. Winchell, M. Cohen, J. Woodilla

The kinetics of stabilization have been studied with respect to the isothermal component of the martensitic reaction in ivon-nickel alloys. Although the carbun (or nit-vogen) content may be very low in these alloys, it plays an important vole in the stabilization phenomenon. In fact, if these interstitial elements are removed by moist-hydrogen treatment, no evidence of stabilization is found. In the pvesence of 0.007 wt pct C, the activation energy for the stabilization process is comparable to that -for the diffusion of carbon (or nitrogen) in ferrite) rather than in austenitc. This suggests that the interstitial diffiision controlling the stabilization occurs within the martensitic embryos rather than in the matrix of the parent phase. The kinetics furthev indicate that the interstitial atoms tend to diffuse -from the embryos toward the suvroundings, thereby immobilizing the interface. This appears to be the origin of the stabilizing effect -found in these alloys. PHILIBERT&apos; has shown recently that interstitial elements play an important role in the stabilization of martensitic transformations in iron-base alloys. However, determination of the temperature dependence for this stabilization process has produced values (- 11,000 cal per mol) that cannot be readily identified with the activation energy for diffusion of carbon (or nitrogen) in either ferrite or austenite. In the present work, the isothermal mode of the martensitic reaction was employed to derive the activation energy for stabilization, and this was found to agree fairly well with that for diffusion of carbon (or nitrogen) in ferrite. An iron-nickel alloy with 30.8 wt pct Ni and 0.007 wt pct C was used in these experiments, the specimens being in the form of rods 0.074 in. in diam and 2 1/2 in. long. The specimens were sealed in evacuated vycor tubes and austenitized at 1100°C for 1/2 hr prior to quenching in water. A second series of specimens was decarburized (and denitrogenized) prior to the above austenitizing treatment by annealing in moist hydrogen for 182 hr at 1215°C. In order to achieve a "standard" condition in the austenitic state, all the specimens were transformed to martensite by cooling to - 195°C before the final austenitizing. Both the 0.007 pct C and the decarburized series then had an Mi temperature of about - 30°C. The isothermal martensitic transformation was carried out at a reference temperature of -88"C, and was traced by means of electrical resistance measurements. Each resistance value was normalized by dividing by the resistance of the austenitic specimen at O°C, thus giving a resist- ance ratio R. The rate of decrease of the resistance ratio (-dR/dt) provided a measure of the transformation rate. It was found that a plot of R vs log t at the reference temperature resulted in a slightly curved line which could be closely approximated by two straight lines intersecting at a time of 10 min, as shown in Fig. 1. If G = dR/dlogt is the linear slope of either straight segment, the rate of transformation at any given time is: The ratio of G for 1 less than 10 min to that for t greater than 10 min was 1.19 for the 0.007 pct C series and 1.24 for the decarburized series. These ratios made it possible to compute the transformation rate at any time greater than 10 min, knowing the transformation kinetics prior to 10 min. The stabilization treatment was introduced by up-quenching from the reference temperature, usually after 10 min of isothermal transformation: to one of four stabilizing temperatures between 0" and 22"C. After holding for various times, the specimens were down-quenched to the reference temperature for additional isothermal transformation. In this way, it was possible to compare the transformation rate (- dR/dt), immediately after stabilization with the transformation rate (- dR/dt)U in the unstabilized condition. The degree of stabilization was defined as: Ordinarily, Gs and Gu would be measured after the same time of prim isothermal transformation.

Jan 1, 1960

By H. K. Birnbaum

The effect of 1ow-temperature stabilization anneals on the structure of the 0 phase Au-Cd alloys and on the diffusionless transformations observed in these alloys was examined by X-yay diffraction techniques. A phase separation in the ß-phase region was proposed to account for the experimenta1 results. The effects of quenching from elevated temperatures on the transformation behavior of these alloys were shown to be consistent with the proposed mechanism. IT has been shown that the high-temperature ß phase (CsCl structure) of the Au-Cd alloy system transforms to a phase having an orthorhombic (D2) ß&apos; structurel1-3 for compositions near 47.5 at. pct Cd and a tetragonal (4/m, m, m) ß" structure* in the vicinity of 50.0 at. pct Cd. Both transformations are diffusionless, crystallographically reversible, and occur on cooling at about 60° and 30°C respectively. The temperature interval from the beginning to the end of the transformation is of the order of 5°C in each case. Although the transformations are normally athermal, some of them have been reported to occur isothermally.= wechsler6,7 has shown that the effects of quenching a 49.0 at. pct Cd alloy from elevated temperatures are consistent with the retention of a nonequilibrium number of lattice vacancies. Annealing of these quench effects results in a broadening of the X-ray reflections.8 After a suitable quench, the 47.5 at. pct Cd alloy transforms to a phase having not the p&apos; orthorhombic structure but another structure which has properties similar to that of the ß" tetragonal structure.5.9 This change in the type of transformation has also been obtained after long anneals in the ß-phase region at about 70oC10 The present investigation was primarily concerned with the structural changes accompanying the above transformation phenomena. The change in transformation product and accompanying physical changes during an anneal in the ß phase have been termed stabilization effects. Experimental Procedure —The results reported in this investigation were obtained with the use of a Norelco diffractometer fitted with a temperature-controlled cryostat. The specimen temperature was controlled to better than ± 0.l°C during the measurements. CrKa radiation monochromated electronically with the use of a scintillation counter and pulse height analyzer was utilized. Specimens containing 47.5 and 50.0 at. pct Cd were prepared by sintering filings obtained from homogenized ingots of the proper alloy composition. (Gold of 99.999 pct purity and cadmium of 99.98 pct purity were used). All heat treatments were carried out with the specimens capsulated in vacuum ( < 10 % mm Hg) or in a He-H gas mixture. The quenching technique used in these experiments was to drop the pyrex capsule which contained the specimen from the annealing furnace into water, the temperature of which was controlled. The pyrex capsule shattered on contacting the water resulting in a relatively rapid quench. After the heat treatment, the specimens were mounted in the diffractometer and were left undisturbed in the diffractometer specimen holder during each sequence of measurements. EXPERIMENTAL RESULTS A) Low-Temperature Annealing—The transformations which were considered "normal" for these alloys were those obtained athermally during furnace cooling at approximately 50°C per hr after an elevated temperature anneal. Under these experimental conditions, the specimens were observed to transform to phases having structures whose diffraction patterns could be indexed as the ß&apos; orthorhombic structure for the 47.5 at. pct Cd and as the 0" tetragonal structure for the 50.0 at. pct Cd alloys. The transformation temperatures on cooling were approximately 60" and 30°C, respectively. Under the "normal" conditions both transformations were observed to go to completion, i.e., the entire volume of the ß phase was transformed to the product phase. In some specimens an extremely weak ß 110 reflection was observed at 20°C indicating that a small amount of retained ß was present. The effect of low-temperature annealing on the nature of the diffusionless transformations was examined for the 47.5 and 50.0 at, pct Cd alloy. The specimens were annealed in evacuated capsules at temperatures in the vicinity of 600°C (as specified in Table I) for 24 hr and were then cooled to 100°C at a rate of 50°C per hr. The specimens were then removed from the capsules and mounted in the diffractometer without allowing the specimen temperature to drop below 80°C. Annealing at the low temperatures was accomplished in the diffractometer by means of the cryostat which was mounted around the specimen. During the low-temperature anneals the lattice parameter, integral breadth of the reflections, and ratios of the integrated intensities of the fundamental and super lattice reflections for the 0 cubic phase were periodically determined. After annealing for the required time, the specimens were slowly cooled in the diffractometer and the diffraction patterns were recorded as a function of temperature. The specimens were cooled until the phase transformations were completed, following which the specimens were heated and diffraction

Jan 1, 1960

By Carlos G. Valenzuela

The value generally accepted for stacking-fault energy, of copper has been approximately 40 ergs per sq cm based on Fullman&apos;s2 value for the coherent twin-boundary energy and the assumption that is twice the twin boundary energy However, Thornton and coworkers8 determined that the lower limit of for copper is approximately 60 ergs per sq cm, based on measurements of dislocation-node radii. They suggested that the assumption of = 2t is invalid. It is the purpose of this note to present results which indicate that the values of obtained by measurement of twin-grain boundary intersections and the values obtained by measurement of dislocation-node radii are actually compatible. The most reliable values for of the a brasses, based on electron-microscope observation of dislocation nodes, are probably those values reported by Smallman and Green6 who applied the Siems correction (1961) to data obtained by Howie and Swann.3 These values shown in Fig. 1 give an extrapolated value of approximately 70 ergs per sq cm for pure copper. In the present work, Fullman&apos;s method for determining the stacking-fault energy of copper was extended to the a brasses. High-purity copper (99.999 pet) and high-purity zinc (99.999 pet) were mixed in proportioned amounts and melted in sealed and evacuated quartz tubes. The alloys were homogenized for a week at 750°C and chemically analyzed by means of X-ray fluorescence. These alloys, along with a specimen of pure copper, were rolled to 98 pet reduction and a thickness of 0.009 in., resealed, and annealed for 40 hr at 715°C. Values for the ratio of twin-boundary energy to the grain-boundary energy, it gb, were obtained from measurements of dihedral angles formed at the intersections of twin boundaries and grain boundaries by using Fullman&apos;s2 mechanical analogy of surface tensions acting at the intersection of an annealing twin and a grain boundary. The angles between the twin traces and the grain boundaries were measured for a large number of twin-grain boundary intersections at a magnification of X500 using a rotating mechanical stage on a Reichert metallograph. The rotary stage has a calibrated angle scale with vernier so that measurements can be made to 0.1 deg. The mean twin-grain boundary energy and standard deviation were calculated for copper and each of the brasses by the use of an IBM 7072 computer. It was found that the mean value of gb stabilized after approximately 100 twin-angle measurements. This was determined by plotting the mean against the number of angles measured. Since the measured angles deviate from true dihedral angles, a correction factor for grain orientation, discussed below, was applied. The stacking-fault energy was then calculated from these values and the values of grain-boundary energy derived by Taylor.7 The data obtained are tabulated in Table I. Values for stacking-fault energy are plotted in Fig. 1. The value of gb for the specimen of 1.03 pet Zn is close to the value obtained by Fullman2 for OFHC (99.98 pet) copper, 0.045. It is believed that the purity of the copper affects gb significantly. The 99.999 pet purity Cu used in this investigation yielded a value of yt/ygb, 0.76, which is much higher than that obtained by Fullman. Additional evidence suggesting that the purity of

Jan 1, 1965

By D. H. Woodard

One of the principal uses of polarized light in metallurgy is to show the granular structure of metals by contrasting reflections. This use is confined largely to anisotropic metals, such as beryllium, tin, magnesium, and the like.1 Recently, Hone and Pearson2 have extended the use of polarized light to include the isotropic metal aluminum. This was made possible by the formation of an anodic film that was optically anisotropic and that had a fixed and reproducible structural relationship to the grains in the substrata. With their method, it was possible to indicate localized textures in annealed aluminum sheet. In the course of an investigation of plastic deformation at the National Bureau of Standards, it was found that the isotropic single phase alloy Monel could be made optically anisotropic by treatment with the usual Monel contrast etchant. Experiments soon showed that dif- , ferences in orientation could be detected easily. Previous investigations involving the use of polarized light have been restricted to annealed metals. In this paper it will be shown that inhomo-geneous plastic deformation which results in lattice bending and development of deformation bands, experienced by individual grains in polycrystalline Monel, is revealed in the microstruc-ture. This interpretation of the micro-structure was confirmed by a study of slip lines formed after prior plastic strain. Materials and Procedure The material used was Monel, the chemical composition of which was C—0.17 pet, Mn—1.28 pet, Fe—1.61 pet, S—0.009 pet, Si—0.17 pet, Cu— 30.70 pet, Ni—66.04 pet. The material was divided into 2 lots which were treated as follows: Lot A was heated at 1700°F for 3 hr to produce a fully annealed, coarse grained structure. Lot B was heated at 1400°F for 1 hr to produce a close approximation of a fully annealed structure without appreciable increase in the grain size of the original material. After each of these heat treatments the material was cooled in air. Samples for metallographic examination were cut from tensile and compression test specimens and were prepared by grinding on lead-tin laps, followed by electrolytic polishing, † Etching and the development of ridges were avoided by keeping the voltage above 3.8 and by preventing contamination of the polishing solution with water. Monel, when polished and treated with most etchants, is optically isotropic. However, when given a light etch for about 4 sec with the Monel contrast solution the surface of the metal becomes optically active. The microstructure when observed under crossed nicols* appears different from that viewed by ordinary light. This is shown by a comparison of micrographs made of the same area of a plastically deformed specimen using polarized light (Fig la) and white light (Fig 16). If Monel, which has been lightly treated with the contrast etchant, is slightly deformed by compression, rectangular figures are apparent over the specimen. However, within too short a period to be photographed, these rectangles become circular, probably because of surface tension effects within the etched film. The two observations,

Jan 1, 1950

By C. G. Wilson

DURING the course of some experiments on the plastic deformation of gallium a standard stereo-graphic projection was prepared with (001) at the center and it was felt that this might be useful to others working with single crystals of gallium. The stereogram, given in Fig. 1, was made using the following crystallographic data (Bradley, 1935):

Jan 1, 1962

By M. Hoch

Equations are derived from statistical considerations to represent the activities of each component of an interstitial solution, and of a compound with a wide homogeneity range as a function of composition and temperature, based on the interaction energies between the various components, Eij. The equations are checked on the binary systems Fe-C, Ta-H, and Y-H, the ternary systems Ti-O-H, liquid Fe-C-0, and the compounds TiO, MnO, COO, and YH,. In all cases the present model represents the experimental data well. THE aim of this paper is to derive from statistical considerations the thermodynamic behavior of non-substitutional solid solutions. "Nonsubstitutional solid solution" means either an interstitial solid solution (carbon in iron, oxygen and hydrogen in hexagonal and bcc titanium, and so forth) or deviation from stoichiornetry in compounds (introduction of vacancies—removal of atoms in one or both lattice sites of compounds FeO, MnO, TiO, NbO, YH2). wagnerl and Fowler and Guggenheim considered the theory of compounds with small deviation from stoichiometry; Anderson includes larger deviations from stoichiometry, the defect being present in one component only, as vacancy and interstitial. Rees considers only vacancies in one of the components and introduces various kinds of sites for the component where the defect occurs; the various sites interact with different energies, thus giving isotherms with two or more plateaus. Both Rees and Anderson are mainly occupied in determining the limits of two-phase regions, and the defect interaction energy is determined from the critical point. Darken and Gurry5 gave a brief treatment of carbon solution in iron; Speiser and spretnak calculated the configurational entropy for binary interstitial solid solutions by assuming that each interstitial atom in the solution excludes a certain number of neighboring interstitial sites from occupancy. Use will be made of this concept later. Hoch et al treated transition metal oxides of the NaCl-type structure, and also oxygen solution in titanium.&apos; The main aim was to determine the behavior of the activity of one of the components as a function of the composition in the single-phase region. In the present paper, the various interaction energies are discussed in detail and the similarity between interstitial solid solutions and deviation from stoichiometry in ionic compounds is shown. Both types of systems have in common that at least on one kind of lattice site only one kind of atom occurs; this gives a fixed frame to the system, permitting a much easier statistical treatment than for the substitu-tional solid solutions. (The theory is also applied to ternary systems.) The difference between an interstitial solution and deviation from stoichiometry can be explained as follows. In an interstitial solution in the pure or standard state the host atom or host structure is present alone and all the interstitial sites which are going to be filled when the interstitial atom is introduced are empty. The interstitial solution is now created by introducing atoms into this empty lattice. In the deviation from stoichiometry, both kinds of lattice sites are already occupied in a special fashion (all lattice sites occupied, or the same fraction of lattice sites empty, or one kind completely filled, the other only two-thirds). Deviation from stoichiometry removes atoms from lattice sites, adds them, or removes atoms from one kind of lattice site and introduces them on the other lattice site. Though both cases (interstitial solution and deviation from stoichiometry) lead almost to the same equations, they are treated separately. The treatment given below corresponds to the "regular solution"10 treatment of substitutional solid solutions. Speiser and spretnak&apos;s6 treatment is similar to the athermal solution in the substitutional use. a) INTERSTITIAL SOLID SOLUTIONS Theory. It will be assumed that there are N lat-tice sites occupied by the host atom (denoted by 1). Corresponding to those N lattice sites there are N octahedral and EN tetrahedral interstitial sites. If only one kind of interstitial atom is added, this in-

Jan 1, 1964

By R. G. Davies

WeERTMANI has shown that the high temperature steady state creep rate, i, in lead and indium-base alloys obeys an equation of the form where AH is the activation energy, o the applied stress, n the stress exponent, and R and T have their usual meanings. He observed a variation in n from 4.5 for pure metals to 3 for concentrated alloys, which he interpreted as due to Change in creep mechanism from the climb of dislocations in pure metals to a micro-creep mechanism in the alloys. The Cottrell-Jaswon microcreep mechanism of the moving dislocation taking its impurity atmosphere with it was considered to be the most likely process, although short-range order and the segregation of solute atoms to a stacking fault will also give a stress exponent of 3. Steady state creep has been investigated in a Au - 27 at. pct Cu alloy at temperatures above 1/2 TIM where TIM the absolute melting temperature. As the oxidation resistance of this alloy is excellent all tests were carried out in air with a furnace built to give a temperature variation of less than 1°C along the 60 mm gage length. A lever-arm arrangement applied the stress with a load being adjusted between each creep test to maintain a constant stress. As each test produced less than 0.5 pct creep strain, the variation in stress during the test was negligible. The creep strain was measured by a transducer at the end of one of the alloy-steel grips, with the out of balance potential being finally recorded on a variable speed chart recorder. A typical creep curve is shown in Fig. 1. The results, Fig. 2, confirm that n is nearer to 3 than to 4.5; the creep mechanism could be any of those given above. The activation energy, AH, which is independent of stress, is consistent with a diffusion controlled process; the activation energies for the self-diffusion of gold and for the diffusion of gold into Copper are both -45 kcal per ml., There is now considerable evidence, that, when the steady state creep is dependent upon diffusion, irrespective of the actual creep mechanism, the activation energy is independent of the stress. The author would like to acknowledge the financial assistance provided by the International Atomic Energy Agency, Vienna, and the Argentine Atomic Energy Commission.

Jan 1, 1962

By R. G. Davies

The activation energy for steady state creep above -500°C is observed to be independent of the applied stress although it varies from -67 kcal per mole at 2 at. pct Si to -100 kcal per mole at 11 at. pct Si due to changes in crystallographic order. The magnitude of the activation energy, by comparison with Fe-A1 alloys, indicates FeSi type of order in certain alloys. X-ray results confirmed the presence of FeSi type of order. It is proposed that dislocation climb is the rate controlling mechanism for all the alloys. It has been demonstrated that when a diffusion mechanism is the rate controlling process, the formation of a superlattice in brass,1 Fe3A1,2 Ni3Fe,3-5 and Feco6 1) increases the creep resistance, and 2) increases the activation energy for steady state creep. Furthermore, a study of creep in Fe-15 to 20 at. pct A1 alloys7 has revealed that as the alloy composition approaches the long-range order field, there is an increase in the activation energy for steady state creep which is thought to be due to an increase in short range order. Fe-A1 and Fe-Si alloys are similar in that they both form the DO3 superlattice in which aluminum or silicon atoms have only iron atoms as first and second nearest neighbors. There are, however, two important differences between the alloy systems: 1) The superlattice formation at -350°C commences at -10 at. pct si8 as compared to -20 at. pct Al,9 and 2) Fe-A1 alloys form a FeAl (B2 type) super-lattice where aluminum atoms have all iron first nearest neighbors even at 22 at. pct Al, but so far no similar FeSi superlattice has been observed. With the similarity between Fe-A1 and Fe-Si alloys in mind, alloys of iron with 2 to 11 at. pct Si were examined for variations with composition of the activation energy for steady state creep and of creep strength. The temperature range of greatest interest was above 1/2 TM (TM is the absolute melting temperature) where it is usually observed that diffusion is the rate controlling process. A subsidiary X-ray investigation of the Fe-Si system was undertaken in an attempt to define the position of the order-disorder boundary as a function of cooling rate. EXPERIMENTAL DETAILS a) Creep. Specimens whose gage length was 1.5 in. and with a cross-section 0.04 by 0.08 in. were strained in tension by a lever-arm arrangement, and the load was adjusted between each creep test to maintain constant stress. The apparatus and mode of operation have been fully described in a previous publication.7 As each test produced a creep strain of 0.25 pct, the variation in stress during the test was negligible. Creep strain was measured at the end of one of the alloy steel grips by a displacement transducer with the out-of-balance potential being recorded on a variable speed recorder. The full-scale deflection of the recorder could be varied in steps to give limits of sensitivity of between 0.1 and 0.001 pct creep strain. The alloys, Table I, were made available by the Metallurgical Department, National Physical Laboratory (N.P.L.), england,10 and by the Research Department, General Electric Co. (G.E.), Schenectady, N.Y. They were hot worked at -850°C, warm worked at 550° to 650°C, and recrystallized in vacuum at -750°C to give a grain diameter of -0.1 mm. All the alloys had a very low impurity content; those from the N.P.L., for which a complete analysis is available,&apos;&apos; show carbon less than 0.026 pct, manganese less than 0.006 pct, and oxygen plus nitrogen less than 0.0024 pct. b) X-ray Procedure. A General Electric XRD-5 X-ray set with a focussing lithium fluoride mono-chromator in the diffracted beam, and a pulse height analyzer to eliminate harmonic wavelengths of the cobalt radiation, was used to investigate the structure of several very fine grained (grain diameter <.01 mm) Fe-Si alloys after the following heat treatments: 1) Quenched from 700°C, 2) slow cooled from 650°C (-40°C per hr), and 3) very slowly cooled from 400° to 100°C (10°C per hr with a 24 hr anneal every 100°C). The method of obtaining the diffraction pattern over the range of 20 from 15 to 45 deg was to count for at least 100 sec every l/3 deg with a slit subtending 1 deg in 20 at the focus; the probable counting error was less than 2 pct.

Jan 1, 1963

By Robin O. Williams

The increase in internal energy as the result of deformation has been measured for lead, aluminum, silver, nickel, iron, and zirconium by using rapid, adiabatic compression. The stored energy increase is roughly Proportional to the strain; the propor-tionality constant increases rapidly with increasing melting point. The fraction of the mechanical energy which is stored increases more slowly, since the strength of the metals also increases with melting point. The values of the stored energy are considered accurate to about 10 pet. The present values appear about 50 pet larger than the more reliable published results where comparisons are possible. It is possible that this difference is due to the high strain rate used in this investigation. Immediately after deformation all these metals release energy at a rate roughly proportional to (time)-&apos;. This release is considered to be associated with dislocation motion but in aluminum (and copper) some additional process seems to be present. This release can represent 20 pet or more of the stored energy. WHEN pure metals are plastically deformed, most of the mechanical energy is converted into heat. The energy remaining within the metal is significant in that it is the energy of the disorder produced and thus detailed knowledge of this energy is a powerful tool in understanding the nature of deformational disorder. While much effort has been expended on this problem, the amount of information available is limited. The situation as of 1958 has been carefully reviewed by Titchener and ever.&apos; The present results have been obtained by a new experimental approach to this problem. The method necessitates high-strain rates which make comparisons with published results less certain, but a high-strain rate is an advantage in that the energy release immediately after deformation can be followed. EXPERIMENTAL PROCEDURE In the experimental method used, the internal (stored) energy is given as the difference between the mechanical work used in deforming the sample and the heat which is released (the first law of thermodynamics). The work is supplied by two identical hammers swinging freely from a fixed height, the available energy being the product of the mass, the gravitational constant, and the distance through which the center of gravity moves. The initial temperature rise of the sample represents the heat produced by the deformation. The sample temperature is determined by a small thermocouple embedded in and supporting the sample. This process can be repeated over and over to produce increased strains. Most samples are run through about five cycles to a total strain of around 0.7. Further details are covered elsewhere. The determination of the heat is dependent upon the sample weight, its specific heat, the rise in temperature, and any gains or losses to the surroundings. One is dependent on published results for specific heals (the values were taken from a collection).3 The values must be accurate to about 0.1 pet in order that they not affect the results. The best values thus do not contribute to the uncertainty, but this is probably not always the case. The accuracy of the temperature rise is limited primarily by knowledge of the thermocouple characteristics over short temperature intervals, but careful calibration eliminates this as an important factor. One can calculate readily the heat flow between the sample and hammers if the time of contact and the sample temperature are known and if there were no oil at the interface. Assuming the maximum temperature difference, upper values for this interchange have been calculated (the time of contact is determined from the decrease in sample length) and it may or may not be significant. However, no correction is colnsidered necessary because of the presence of a thin oil film which has a thermal conductivity much less than the metals. Except for the possible uncertainty in specific heat, the heat is considered to be adequately known. The mechitnical losses which are recognized as important are: 1) friction between the sample and the hammer:;, 2) the kinetic energy in the hammer suspension system which may not be entirely usable, 3) the rebound energy of the hammers, and 4) the vibration of the hammer heads. All these have been covered in detail elsewhere2 and only the more significant points are made here. The friction turns out to be small except for soft materials (lead)

Jan 1, 1962

By M. E. Fine, A. A. Henderson

Investigation of the tensile properties of silver based aluminum alloy crystals was undertaken because it appeared attractive for studying strengthening effects due to Suzuki locking with minimum complication. Yield drops were observed in all alloy crystals (1, 2. 3. 4, and 6 at. pct Al) after strain aging at room temperature. No yield drops were found in similarly grown and tested silver crystals. The yield effects are attributed to Suzuki locking but the major portion of the solid solution strengthening to other mechanisms. INVESTIGATION of the tensile properties of single crystds of silver alloyed with aluminum was undertaken because it appeared to be a system in which segregation at stacking faults associated with partial dislocations1 would be the dominant factor in anchoring dislocations. First, silver and aluminum have closely similar atomic sizes and thus solute atom locking of a dislocation due to elastic interactions should be unimportant. Second, while both X-ray2 and thermodynamic3 investigations show short-range ordering in silver-based aluminum alloys, the degree of local order is quite small (X-ray measurements give v = EAB - 1/2(EAA + EBB) = - 0.025 ev and thermodynamic measurements give v r -0.007 ev) and should not be important in strengthening dilute alloys. Third, the stacking fault energy of silver is probably low (as indicated by the profusity of annealing twins) and is very likely diminished further and quite rapidly by aluminum additions since the A1-Ag phase diagram shows a stable hexagonal phase at only 25 at. pct Al. Also, a careful investigation in this laboratory4 has shown that the ratio of twin to normal grain boundaries in recrystallized alloys increases with aluminum content. Thus, with minimum complication from other factors, Ag-A1 alloys seem attractive for studying strengthening effects due to segregation at stacking faults of extended dislocations. EXPERIMENTAL METHOD Single crystals measuring 250 by 5 by 1.5 mm of pure Ag (99.99 pct) and Ag-A1 alloys (A1 of 99.999 pct purity) of nominal compositions* 1, 2, 3, 4, and 6 at. pct were grown in high-purity graphite molds from the melt under a dynamic vacuum (1 x l0-5 mm Hg). The technique consisted of moving a furnace having a hot zone (which melted about 0.5 cm of alloy) over a horizontal, evacuated quartz tube con- taining the mold and alloy at a rate of 3/8 in. per hr. Chemical analysis showed roughly the first inch of the crystal to be solute poor, the last inch solute rich; and the center section uniform in composition within the sensitivity of the analytical method (± 0.2 at. pct Al). The center section of the crystal was cut into five specimens. Gage lengths of reduced cross section, measuring from 1.5 to 2 cm in length, were mechanically introduced by means of jeweler&apos;s files and fine abrasive cloth with the crystal firmly held in polished steel guides. One-third of the cross section was then removed by etching and electro-polishing, the crystals were all subsequently annealed for several days at 850°C in a dynamic vacuum (<1 x 10-5 mm Hg) and furnace cooled to 200°C. The crystal orientations were determined using the usual back-reflection Laue technique. The Laue spots were sharp and of the same size as the incident beam. However, microscopic examination showed the crystals to contain substructures with subgrains of the order of a micron in diameter. The details of this substructure are presently under investigation. Tensile testing was done with a table model Instron using a cross-head speed of 0.002 in. per min. For testing at various temperatures the following media were used: 1) 415oK, hot ethylene glycol; 2) 296ºK, air, acetone, water; 3) 273ºK, ice water; 4) 258ºK, ethylene glycol "ice" in ethylene glycol; 5) 200°K, dry ice in acetone; 6) 77ºK, liquid nitrogen. EXPERIMENTAL RESULTS A) Yield Behavior—A portion of an interrupted stress-strain curve for a 6 at. pct A1 crystal of the indicated orientation tested at room temperature is shown in Fig. 1. Initially, at (a), there is a small, gradual yield drop of about 10 mg per sq mm2. However, on stopping the test, and aging for a few minutes at (b), a sharp yield drop is found. Aging for longer times at (c) and (dl results in larger yield drops (and larger AT&apos;S). At, defined in Fig. 1, is usually larger than the yield drop by about 20 pct; however, this increase in the lower yield is transient since extrapolations of the flow stress curves join as may be seen from Fig. 1. (Both Laue and low-angle scattering photographs revealed no evidence of precipitation in a strain-aged 6 at. pct A1 crystal.)

Jan 1, 1962