Search Documents

By Filippos Patsiogiannis

Laboratory size (4.5 kg) low carbon steel melts were deoxidized using Al and FeAl (33% Al), with and without synthetic fluxes, in alumina and zirconia crucibles. The dissolved oxygen, total oxygen, soluble aluminum, insoluble aluminum, silicon and carbon contents in the melt were determined as a function of refining time and temperature. It was observed that the reaction between aluminum and oxygen in solution closely follows thermodynamic equilibrium. Silica present in the alumina crucibles was found to be a source of oxygen for the melt, while this was not the case for zirconia crucibles. Reoxidation of the melt occurred through oxygen pick-up from the atmosphere. The extent of this reoxidation was found to be a function of oxygen content of the bath and the slag cover on the surface of the melt. The effectiveness of calcium-aluminate based fluxes in protecting the melt from the reoxidation and in increasing the rate of removal of inclusions was evaluated.

Jan 1, 1992

By Filippos Patsiogiannis

Laboratory size (5 kg) aluminum killed low carbon steel melts were desulfurized with synthetic fluxes in zirconia crucibles. The sulfur, oxygen, aluminum, silicon, and manganese contents in the melt were determined as a function of refining time and temperature. With a good argon shield and synthetic flux cover, melt reoxidation was not observed. Sulfur removal followed first order reaction kinetics. The effectiveness of calcia saturated calcium-aluminate (12CaO.7Al2O3) based fluxes in desulfurizing the steel melts was evaluated. The effects of initial sulfur level of the melt, weight of the flux (slag), and additions of tellurium, fluorspar, and barium oxide to the melt on the kinetics of desulfurization were also studied.

Jan 1, 1993

By B. D. Paphane

Since the commissioning of the Tati Hydrometallurgical Demonstration Plant (HDP), which produces Ni and Cu cathodes as well as Co salt from sulphide concentrate employing Activox® technology for leaching, no kinetic data has been generated from the plant under normal operating conditions, from start-up to steady state. Therefore, this study seeks to determine the rate of reactions in the leaching circuit with a view to obtaining kinetic data for the system under the current operating conditions. Within the five-compartment autoclave operating at temperatures of 105°C to 110°C and 1100 kPa pressure, the extraction of Ni, Cu, and Co ions into solution is achieved through the oxidation of the sulphide concentrate using approximately 50 kg H2SO4 per ton, 10 kg NaCl per ton, and 1.21 kg O2 per kilogram of S2-. The autoclave reactions showed complex kinetics, with the reactions proceeding via some intermediate(s) before the formation of products. The results suggest that the reactions were dependent on the size of the metal ion of interest and the concentrations of the metal ions in the Tati concentrate as well as in chloride leaching. The order of the leaching rate constants was Fe2+ > Cu2+ > Ni2+ > Co2+ in all the compartments studied. The rates of leaching were also found to decrease as the concentrate moves from compartment 1 to compartment 4. For compartments 1 to 3, leaching was observed to be preceded by dilution of the repulp liquor (copper raffinate). The leaching rate for compartment 5 was slightly lower than that of compartment 1 but higher than the rates of compartments 2, 3, and 4 for all the metals studied. Keywords kinetics, hydrometallurgical plant, Activox

Jun 1, 2013

By José Roberto de Oliveira

Based on literature review one can see that the main objectives of MnO reduction is the comprehension of slag interactions and reactions with other elements beyond carbon. That's because it is worthwhile to study pure MnO reduction, where there will be not oxides interaction and just carbon will be the reduction agent. By a thermodynamic analysis we know that Si can react with MnO, then it's important to study this influence, so as Mn content. Our work aims to develop kinetics parameters for the MnO reduction, varying Mn and Si contents in bath. This has been given by pressure measure of CO in a Fe-C bath. The CO is generated by the oxide reduction with carbon. It has been proved that: - Mn content decreases the MnO reduction; - the MnO reduction is mainly influenced by Si content in a bath containing Iron, Carbon and Manganese so as Silicium

Jan 1, 1997

By Jorge Alberto Soares Tenório, Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Franco Alves Lavacchini Ramunno

"The traditional process for recovery of metals from waste electric and electronic equipment (WEEE) usually involves pyrometallurgical processing. However, the application of this technology to processing waste printed circuit boards (WPCBs) might lead to the formation of dioxins and furans, due to thermal degradation of flame-retardants and polymeric resins present in the board substrate. Therefore, this paper proposes a hydrometallurgical route for the recovery of copper. The acid leaching behavior of copper has been investigated at three different temperatures (25°C, 50°C and 75°C) with and without the addition of an oxidizing agent (hydrogen peroxide - H202). The dissolution kinetics for acid copper leaching was calculated based on chemical analysis by ICP-OES (Inductively Coupled Plasma - Optical Emission Spectroscopy). At 50°C with 1 mol/L H2S04 added 10 mL H202 (30%) each half hour under pulp density of 1 g I 10 mL, 100% of copper was extracted after 3 hours. The dissolution kinetics of copper with H2SO4-H2O 2 followed 1 - (1 - X)113 =Ket, i.e. chemically controlled reaction model.IntroductionThe information regarding the generation of waste electric and electronic equipment (WEEE) are still difficult to obtain because the estimates should take into consideration the historical production and sale of various products and the rate at which they reach the end of their life cycle, whose duration depends on the behavior of consumers [1]. Thus, the estimated overall WEEE generation varies between 25 and 50 million tons each year, which corresponds to more than 5% of all municipal waste generated [2], and this amount will increase at a rate of 3 to 5% per year, approximately three times faster than other individual types of waste [3].Printed circuit boards (PCBs) are essential parts of electric and electronic equipment (EEE), being found in virtually all electronic products, as well as in weapons systems [4]. A PCB is a basic component, which consists of a board where copper tracks are deposited. While the board behaves as an electrical insulator, the tracks connect electrically the various components attached to the board [ 5]. In addition to glass fibers, paper and resins, the PCBs contain significant amounts of metals, such as copper, iron, nickel, lead, stain, silver, gold and palladium [6]. In general, the weight fraction of metal is around 28% and the remainder of the boards is composed of plastic (19%), bromine (as flame retardant - 4%) and ceramic material (49%) [7]."

Jan 1, 2014

By Baozhong Zhao

Laboratory experiments have been conducted on the removal of As, Sb and Bi from molten copper by SF 6 injection. The results showed that the impurities can be removed by SF6 injection in the? sequence of Sb >As >,Bi and the rate of Bi removal is affected significantly by the concentration levels of As and Sb in the copper melt. Analysis of the experimental data indicates that the impurity removal process is under chemical reaction control rather than by mass transfer of impurity through the molten copper phase. On the basis of experimental results, a kinetic model was developed and the order of chemical reaction and the volumetric chemical reaction rate coefficients of impurity removal were determined.

Jan 1, 1996

By Mamookho Elizabeth Makhatha, Mbal Henock‑Michel Mwanat, Kubangala Brest Kasongo, Ntumba Edward Malenga

This study investigated the operating parameters that affect the kinetic dissolution of copper and cobalt from sulfidic ores. The sulfuric acid concentration, temperature, sodium chloride concentration, particle size range, and leaching time were selected to deduce the kinetic mechanism of the leaching reaction. Other parameters, such as a stirring speed of 250 rpm and the percentage solid 10% w/v, remained constant. The results reveal that an increase in acid concentration enhances the leaching rate of copper and cobalt. Copper and cobalt dissolution was positively affected by the addition of sodium chloride. The highest leaching rates of copper and cobalt were 24.71% and 15.65%, respectively. The chemical control and diffusion control by shrinking core models are well fitted as the kinetic models representing the dissolution of the minerals. The respective activation energies for copper and cobalt dissolution of 10.92 and 31.023 kJ mol− 1 for the chemical control and 18.83 and 37.28 kJ mol− 1 for diffusion reaction control were established from temperature-based experiments.

Aug 26, 2022

By Inkap Choi

Asbestos is a broad term embracing a number of fibrous silicate minerals. These minerals look extremely fragile, yet their fibers have a tensile strength equal to that of piano wire. Chrysotile asbestos is the only mineral that can be woven into cloth, and its fibrous structure is, if anything, even more amazing than its remarkable ability to withstand heat. Because of its unique physical properties asbestos has achieved great industrial importance, and more than 3,000 current uses are known, ranging from use in the kitchen to use in space missiles. Because their minuscule fibers are eminently respirable, asbestos minerals have also found their way into the lungs of humans, where they apparently produce serious biological effects such as asbestosis and lung cancers. 1, 2,3 Because of both their usefulness and their hazardous properties, these minerals have attracted a good deal of attention from research workers during recent years. For example, the surface properties of asbestos minerals have been studied by many investigators. 4, 5, 6, 7, 8, 9 However, even for the important mineral chrysotile, the literature data are more or less conflicting. Pundsack4 measured a PZC (point of zero charge) of 10.1; Martinez and Zucker5 measured 11.8; Chwastiak reports 10.8-11.0; and Raddick measured three sepa-rate apparent PZCls at about pH 8.3, 10.0 and 10.9. More recently Trivedi8 reports 10.11. Naumann and Dresher9 have studied surface charge enhancement of chrysotile by metal ions, and describe how the mineral reacts with contaminantions. In the present paper, the mode of dissolution of magnesium and hydroxyl ion from asbestos minerals placed in water was studied by kinetic experiments involving rate at which these items leave the minerals. Also, some study was made of interaction between dissolved species.

Jan 1, 1972

By Dewa Putu Agus Sudarmaja, Widi Astuti, Januarti Jaya Eka Putri, Yayat Iman Supriyatna, Himawan Tri Bayu Murti Petrus, I Wayan Warmada, Siti Nurul Aisyiyah Jenie, Ferian Anggara, Anisa Maulidia, Vincent Sutresno Hadi Sujoto, Sutijan

With the rapid development of renewable energy technology, such as electricity reserves, to store energy for electric or electric vehicles, environmentally friendly energy sources are expected to continue to be fulfilled according to mobility and stationary energy needs. Lithium is the most attractive candidate for energy storage development. The presence of lithium in Indonesia in the Sidoarjo mud content is interesting to be used as an alternative source of raw materials. During the research, sulfuric acid acted as a solvent, and hydrogen peroxide acted as an oxidation agent. Lithium recovery will be studied using a leaching process at various temperatures (30, 45, and 60 °C) and sulfuric acid concentrations (0.5, 1, 2, 3, 4, and 6 mol/L). The increasing temperature, sulfuric acid concentration, and hydrogen peroxide concentration will directly affect the lithium recovery. An increase in sulfuric acid concentration will be directly proportional to the recovery of lithium in the solution. Optimum conditions were obtained at varying 6 mol/L sulfuric acid concentrations and 60 °C temperature variations. The shrinking core model (SCM) studied leaching kinetics, and ash layer diffusion acted as a rate-controlling process. The activation energy of the leaching process was obtained at 38.90 kJ/mol.

Jul 25, 2023

By R. Baker

A novel electrochemical half-cell and corresponding working electrode were designed to evaluate the electro-catalytic activities of catalysts in an environment close to that of an operating proton exchange or polymer electrolyte fuel cell (PEMFC). Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) techniques were employed using the novel cell to characterize various methanol electro-oxidation parameters that contribute to the overall reaction on a fuel cell anode. The effect of temperature on methanol oxidation kinetics was examined in the potential range of 0.31 to 0.65V (vs. NHE). The data was collected in the temperature range of 20 to 80°C. Based on the experimental analysis and literature data, an equivalent circuit model (ECM) for methanol oxidation was proposed and was used to fit the EIS experimental data. The experimental data and ECM electrochemical data was used to extract electrochemical kinetic parameters for methanol oxidation such as the exchange current density, Tafel slope, and energy of activation for the reaction. Kinetic data, especially at different temperatures, is very limited in the literature.

Jan 1, 2005

By T. T. Chiweshe, L. S. Mokhahlane, M. Welman-Purchase

This study examined an alternative technique of extracting tungsten from wolframite ore using a fusion method with ammonium phosphate salt. Current techniques use alkali salts to decompose tungsten ores and use various purification methods to produce ammonium paratungstate, which is a key intermediate precursor in the extraction of tungsten. In this study, a two-step extraction process, which involves thermal decomposition of the ore using fusion and a separation stage, is examined. The novelty of this technique is the ability to completely decompose wolframite ore and form an unstable tungsten oxide phosphate (WO2(PO3)2) compound. The instability of WO2(PO3)2 in deionized water enables selective isolation of tungsten as insoluble precipitates of WO3 and WO2. The decomposition reaction of WO2(PO3)2 is influenced by the presence of oxygen and determined to be first order under ambient conditions. Scanning electron micrographs and X-ray diffraction analysis showed above 80% of the tungsten precipitated compared with the amount that remained in the filtrate solution.

Jul 10, 2024

By Gerald Onyedika, Tochi Onwumere, Martin Ogwuegbu

"The kinetic study for the leaching of iron from cassiterite ore in KOH solution was studied. The effects of KOH concentration, particle size and reaction temperature on the leaching rate of iron were also examined. The results of leaching studies showed that the leaching of iron from cassiterite ore in KOH solution is significantly influenced by the reaction temperature, KOH concentration, and decrease in particle size. The study showed that 90.62% of iron ore was leached in 8M KOH solution at 80°C within 120 minutes. The experimental data were well evaluated using the shrinking model for surface chemical reaction and diffusion control through the product layer. The activation energies for the iron ore dissolution using the two models were calculated to be 32.06KJmor1 and 97.97 KJmor' respectively.IntroductionIn recent times, there has been increasing attention on the kinetic study of mineral dissolution. In most of these studies, the experimental results were analyzed with a suitable shrinking core model under the assumption that the ore is a homogeneous spherical solid phase [1-4]. A study of the dissolution kinetics of a Nigerian cassiterite ore by hydrochloric acid showed that increase in the hydrochloric acid concentration is accompanied with increase in the amount of cassiterite ore dissolved at various times [4]. The optimal concentration was found to be 4.0M HCl, after which there was a decline in the amount of the ore dissolved, which showed that the concentration of the reagent has a significant effect on the leaching rate of the ore. Also in studying the effect of stirring speed on the rate of cassiterite ore dissolution while keeping other conditions constant for 120 minutes, the result showed that the rate of cassiterite ore dissolution was dependent on the stirring speed over a range of 0 to 630 rpm. Above 360 rpm, the stirring speed no longer had any effect on the solid dissolution. The dissolution rates of cassiterite were analyzed using a suitable shrinking model. The results showed that the reaction was controlled by the diffusion of tin through the porous product layer, a reaction order with respect to hydrogen ion concentration of 0.92 M and activation energy of 50.05KJmor'. In another kinetic study on the leaching of a low grade niobium-tantalum ore with concentrated KOH solution the effect ofreaction temperature, KOH concentration, agitation speed, particle size and alkali-to-ore mass ratio on the dissolution rate of niobium were examined [5]. The result of niobium leaching from low grade niobium-tantalum ore with concentrated KOH, solution at different agitation speeds showed that the dissolution rate increased with increase in agitation rate. In the case of particle size effect, the results show that small particles require much shorter time for complete dissolution than the large ones."

Jan 1, 2013

By J. B. Hiskey

The principle oxide minerals of molybdenum are wulfenite (PbMoO4), ferrimolybdite (Fe2(MOO 4)3.nH2O), powellite (CaMoO4), and ilsemannite (Mo304). Wulfenite is found in Arizona, New Mexico, Nevada, Utah, California, and Montana. It is also found in the states of Sonora and Chihuahua, Mexico. Prior to 1915 wulfenite ores were the primary source of molybdenum. The solubility of wulfenite in hot sodium sulfide was first noted by Bonardi(1) during attempts to sulfidize wulfenite material prior to flotation. He identified lead sulfide and soluble sodium molybdate as reaction products. Bacon (2) sulfidized wulfenite in preparation for flotation and by X-ray analysis found the reaction product to be lead sulfide. Holmes(3) made an extensive investigation of the extraction of molybdenum from wulfenite concentrates by leaching. Nearly 100% molybdenum extraction was possible from -100 mesh samples leached for 15 min with 10% sodium sulfide solution at room temperature. Molybdenum extraction from -100 mesh samples after leaching 30 min at a temperature of 45°C using 2, 4, and 6% sodium sulfide was about 32, 79, and 98% respectively. The extraction showed little sensitivity to time, temperature, or particle size using 10" sodium sulfide solution.

Jan 1, 1976

By A. P. Mehta

The role of microorganisms in the leaching of metal sulfides is well established (Torma, 1977; Murr, 1980). However, this established knowledge applies mostly to chemolithotropic microorganisms such as Thiobacillus ferrooxidans which function optimally in leaching catalysis between 25-35° C, and in a pH range of 2-2.5. Although leaching with thermophilic microorganisms capable of extending the range of catalytic viability beyond 35° C is also documented, there are few if any attempts to optimize or extend sulfide concentrate leaching with thermophilic microorganisms. When mixed metal sulfides or other materials having different rest potentials (referenced to the standard hydrogen electrode, SHE, in the electromotive series) make contact in a conducting, aqueous medium, the contacting members will act as an electrochemical cell, with the member having the higher rest potential assuming the role of an electrical cathode. In leaching reactions involving such galvanic couples, the cathode becomes passivated, while the anodic member reacts vigorously due to the electro- chemical reaction which occurs (Hiskey and Wads- worth, 1975). Serry, eta1 (1978) observed that when chalcopyrite and pyrite were in intimate contact in natural ores, the chalcopyrite reacted vigorously by galvanic conversion as a result of the higher rest potential (~ 0.63 V) as compared to the chalcopyrite (~ 0.53 V). In addition, it was postulated that because of the elemental sulfur which can form on the anodic chalcopyrite in this galvanic conversion process, reactions in acid-bacterial medium would be expected to have accelerated copper extraction because of the conversion of any sulfur product layer on the chalcopyrite anode to sulfuric acid according to the following general reactions: [MS?M2+ + S° + 2e- (1) and 2S° + 302 + 2H20 bacteria?-2H2SO 4 (2)] where M in reaction (1) designates the metal (or metals in the specific case of chalcopyrite) to be released to solution by galvanic conversion.

Jan 1, 1982

By S. N. Shahcheraghi

Bioleaching method makes use of bacteria in solving metallic sulphides, so that these bacteria tend to convert insoluble metal sulphides into soluble sulphates. Since the kinetics description of this process is inevitable for better interpretation of relation between metabolism and growth of live organisms, as well as optimization of metals extraction processes, in this paper, this description is represented and designed in mathematic (kinetics) model for copper sulphide minerals based on Monod kinetics model. According to this model, special growth rate of bacteria (?) is a hyperbola function of restrictive substrate concentration (S). By Solving and developing of Monod kinetics model, a comprehensive kinetics model for bioleaching of copper sulphide minerals results. The designed is also applicable for other metal sulphides.

Sep 1, 2012

By E Christodoulou, L Zoumpoulakis

The kinetics of the thermal decomposition of MgCO3 was investigated using isothermal experiments performed in a thermogravimetric analyzer under a nitrogen atmosphere at 380¦, 400¦, 450¦ and 480¦C. The weight loss data as a function of time were modified to give the fraction that reacted (ß) and the rate of reaction (dß/dt) vs. time (t). Kinetic analysis of the experimental results, using three different methods, showed that diffusion predominates the MgCO3 decomposition over the investigated temperature range, with the data being best fitted by JanderÆs equation ([1−(1−ß)1/3]2=kt). The activation energy was estimated by Arrhenius plots using both the initial reaction rates and rate constants from fitting the above equation. The values estimated were 27.1 and 171.4 kJ/mol respectively.

Jan 1, 2001

By José Roberto de Oliveira

In a smelting reduction process the reduction reaction occurs predominantly in the liquid state. The main reduction agent is the carbon from the carbon saturated iron bath. The aim of the present work was to determine the velocity equation and the rate constant of the reduction rate of MnO content in a Mn0-SiO2-Fe0 slag by iron saturated carbon and the carbon dissolution rate in a Fe-Mn bath. The manganese content in the iron bath was in the range of 5 to 15 wt.%. It was observed that the rates of carbon dissolution in all Fe-Mn baths are faster than the rates of MnO reduction by the carbon saturated liquid iron.

Jan 1, 1999

By M. Zhang, H. Ni, F. Zheng, M. Guo

"In the present work, we investigate the effects of roasting temperature and time on the transformation of the titanium (Ti)-bearing phase and magnesium aluminate spinel (MgAl2O4) phase in Ti-bearing electric arc furnace molten slag during the molten sodium hydroxide (NaOH) treatment process. With applied temperature of 700 °C for 60 min, and a mass ratio of Ti-bearing electric arc furnace slag to NaOH, or Rslag/NaOH, of 1:1.2, the conversion ratios of the Ti-bearing phase and the MgAl2O4 phase reached about 98.3 percent and 88.1 percent, respectively. Moreover, investigation of the reaction kinetics indicate that the conversion of these phases during the molten NaOH treatment process is a typical solid-liquid reaction, and it can be theoretically described by the unreacted shrinking core model. The conversion ratio of the Ti-bearing phase was found to be controlled by the chemical reaction step, with an apparent activation energy of 41.76 kJ/mol. The decomposition of the MgAl2O4 phase was found to be controlled by the surface chemical reaction in the early stage of 0 to 20 min from start of reaction, changing to diffusion control in the later stage of 20 to 60 min. The apparent activation energies of the process were determined as 55.88 and 22.72 kJ/mol, respectively.IntroductionChina has rich mineral resources of vanadium–titanium magnetite ore deposits, and the iron and steel industry in the country produces millions of tons of titanium (Ti)-bearing slag every year. The problem of how to dispose of the Ti-bearing slag has attracted much attention, and various approaches have been developed, including the acid process (Li et al., 2007; Zhang et al., 2011; Zhang and Nicol, 2010; Li et al., 2011), alkali fusion process (Han et al., 2012; Middlemas, Fang and Fan, 2013; Nayl, Awwad and Aly, 2009; Lasheen, 2008; Zhang, Qi and Zhang, 2009), carbonization and chlorination process (Liu et al., 2008; Tao et al., 2012; Fu et al., 2012; Liu, 2009), selective crystallization process (Lei and Xue, 2008; Li et al., 2011; Zhang et al., 2007a, 2007b). However, these processes have been beset by various functional, economical and ecological problems (Yu and Chen, 2010). With environmental protection regulations becoming increasingly rigorous, and demand growing for the comprehensive utilization of resources, the focus is on methods to treat Ti-bearing slag with high efficiency and mild reaction conditions (Nazari and Riahi, 2011; Wu et al., 2013)."

Jan 1, 2017

By P. C. Beuria

Iron ore concentrate contains different mineral phases viz. hematite, magnetite, goethite, kaolinite, and gibbsite. Presence of some of these phases like goethite, kaolinite, and gibbsite contribute to the loss on ignition (LOI) content of the sample. Iron ore fines (pellet feed) are pelletized for utilization in DRI & BF processes. In the present pelletization technology i.e., straight grate and grate kiln processes, the LOI in the ore should be within the range of 2.0-2.5%. LOI content in the iron ore concentrate is found to be more than 4% after beneficiation of low-grade iron ore. It is therefore difficult to produce good quality pellet because of high LOI content. The LOI content of the sample is a detrimental factor in the pellet making. For effective pelletization, the LOI content in iron ore fines needs to be reduced before pelletization. It can be reduced by fluidized bed roasting. The objective of present work is to understand the kinetics of removal of LOI from iron ore fines. The effects of bed depth, temperature, and residence time on reduction of LOI content in iron ore fines were studied using muffle furnace. The process of roasting was carried out at four different temperatures varying from 400 to 950 °C with a variable residence time of 30, 45, 60 & 75 minutes and at bed depths of 16, 32, 48 & 64 mm. In all instance of experiments carried out, one of the parameters was kept constant. It was observed that at 850 °C and 30 minutes of residence time, there was sufficient removal of LOI in static bed condition even at a high bed depth of 64 mm. Keywords: LOI, pellet feed, fluidized bed roasting, goethite

Sep 1, 2012

By Zoran S. Markovic

The extensive laboratory investigations were carried out in order to determinate behavior of sulphide and nonsulphide copper bearing particles during the flotation. The present ore sample were contained 0.55% Cu with 20.1% of nonsulphide copper in it and gangue material with higher contents of alumina about 19.07%. In this paper will be presented some results such as: effect of particle size, pH and applied collectors. The main goal was in application of collectors S-7518, as well as mixture of KEX and Z-96. Z-96 is a product from Chemical Industry Zupa Krusevac which was used as auxiliary collector in mixture with xanthates. The best results were done with this mixture in ratio KEX / Z-96 as 77/23 % in area of oxidized minerals flotation, but the collector S-7518 was achieved better results in sulphide mineral flotation. The S-7518 has better selectivity between copper minerals and pyrite comparing to mixture of KEX/Z-96 in mentioned optimal ratio. Flotation recovery and copper grade in concentrate were studied by flotation kinetics tests.

Sep 1, 2012