Search Documents

By T. Ivankina, T. Lokajícek, H. Kern, T. Svitek

The knowledge of 3D velocity distribution of P- and S-waves in rocks is very important parameter for interpretation and understanding the nature of seismic anisotropy observed in the earth’s crust and upper mantle. A new high-pressure measuring head was designed and constructed to enable ultrasonic sounding of spherical rock samples in 132 independent directions under up to 60 MPa of acting hydrostatic pressure by means of simultaneous longitudinal and transversal sounding. New measuring system enables ultrasonic sounding of spherical rock samples by using a pair of P-wave sensors and two pairs of perpendicularly polarized S-wave sensors (TV and TH) see Fig.1. Shear wave sensors polarization is oriented according to rotation axis of the sample. Special shear wave gel was used to transfer shear waves between the sample and sensors under acting hydrostatic pressure. An isotropic glass sphere was used to check and calibrate the new measuring setup. A spherical sample of a biotite gneiss from the Outokumpu scientific drill hole was used for testing measurement. There is shown that both, P- and S-wave velocities, can be measured simultaneously up to 70 MPa, respectively. We report data of the 3D velocity distribution of P- and Swaves measured for the first time on a sample sphere of biotite gneiss. We rely, in particular, on the directional dependence of compressional and shear wave propagation and their relationship to the crystallographic (CPO) and shape preferred orientation (SPO) of major rock-forming minerals. The 3D seismic measurements revealed a strong foliation-related directional dependence (anisotropy) of P- and Swave velocities. Ultrasonic measurements were compared with 3D velocity calculations based on neutron diffraction measurements of crystallographic preferred orientation (CPO) of major minerals. Comparison of 3-D velocity distribution (P, S1, S2 and S1-S2) determined by two completely different methods ultrasonic sounding and neutron diffraction is presented. Measurements showed that the intrinsic bulk anisotropy is basically caused by the CPO of biotite constituting about 23 vol.% of the rock.

Jan 1, 2015

By Jr. Hardy, H. Warren Shen

"A study is presently underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which would make it possible to carry out remote monitoring of coal cutting operations. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal breakage and cutting procedures. The present paper will focus on the test facilities, experimental techniques, and results associated with linear, single-bit cutting. An AE-transducer, attached directly to the bit, detected AE signals during the cutting process.Experiments have been carried out on seven specimens of coal obtained from the USBM experimental mine at Bruceton, Pennsylvania. Three separate cuts were made for each of two bit angles (10 and 45 degrees) and two bit velocities (0.085 and 0.169 cm/sec), for a total of 12 separate cuts. Data associated with resulting particle size distribution and AE characteristics (major dominant frequency components) will be discussed. Data analysis has also been underway using a computer-based pattern recognition system known as ICEPAK (Intelligent Classifier Engineering Package). This program is able to evaluate over 100 features of an AE event and to make objective comparisons between AE signals associated with different loading or cutting parameters. The results to date show that AE generated during some of the test conditions can be recognized by ICEPAK with a recognition rate of 90% and higher while other conditions cannot at present be separated with a suitable recognition rate. Further analysis of the experimental data is presently underway.The reduction of the severity, and eventual elimination, of Coal Workers' Pneumoconiosis (CWP) depends on gaining fundamental understanding in a number of major areas. These include dust generation and entrainment, transportation, suppression, medical effects of dust, and possible treatment. At present a project is underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which would make it possible to carry out remote monitoring of coal cutting operations. Suitable on-line analysis of monitored AE data would allow engineers to evaluate factors such as shearer bit conditions and cutting efficiency, and to quantify the particle size and shape distribution of the generateddust. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal cutting procedures. To date experiments have been carried out on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. A brief outline of the overall study has been presented in an earlier paper (Hardy, Shen and Kimble, 1995). This paper will consider the linear single-bit cutting studies in more detail.It is generally accepted today that most solids emit low-level seismic signals when they are stressed or deformed. In this paper this phenomenon will be referred to as acoustic emission (Hardy 1972, 1981, 1989). In essence, the measurement of AE activity in a field or laboratory structure is relatively simple. A suitable transducer is attached to the structure, the output of the transducer is connected to an associated monitoring system, and the AE signals occurring in the structure, due to internal or external stress, deformation, and failure are suitably acquired, pre¬processed and recorded."

Jan 1, 1998

By S. L. de Moraes

This study aimed to identify a way to reduce the use of bentonite in the pelletization of magnetite. With this goal, different combinations of binders were compared to bentonite by examining the quality of pellets obtained by balling drum agglomeration. Pellets were subjected to routine tests that included simple compression of the wet and dry 105°C pellets, dropping wet pellets to determine their ability to survive handling and submitting pellets to thermal shock to determine how they tolerate drying and preheating. The best results use sodium silicate (1.5%) as a binder and show that it is possible to pelletize iron ore without using bentonite.

Jan 1, 2010

By Jamal Rostami, Wei Hu

Efficient performance of EPB TBMs in clayey ground is primarily dominated by the flow capability of the excavated muck in the cutterhead and screw conveyor. Currently, Consistency Index approach is used to evaluate clay clogging potential, but it does not include the effects of surcharge pressure on clay behavior. In this paper, a macro-scale soil rheometer is introduced to assess the clogging potential under various water content and surcharge loading conditions. The results show that, in addition to water content, surcharge pressure has clear impact on clay clogging too. In practice, Consistency Index chart can be refined to incorporate the impact of face pressure to better simulate the EPB tunneling conditions.

Jun 13, 2021

By Jeffrey N. Deisher, H Y. Fang, Richard P. Scheller, Robert M. Koerner

The need to adequately quantify cracking in structures in the vicinity of blasting activity becomes more important each year. This urgency comes about through a growing number of complaints and lawsuits between the various parties involved, i.e., operator/owner, government, and complaintant. It is felt that existing rules and regulations (mainly based on peak particle velocity of the soil or rock adjacent to the structure in question) fall short of such quantification and lead to confusion in adequately assessing structural damage.

Jan 1, 1977

By R. D. Doepker

The dissolution of metals from various metal-mine tailings has been studied through a series of submerged tailings batch tests at U.S. Bureau of Mines laboratories. Tailings selected for this study included both reactive (as determined by column leaching studies) and benign tailings. Metal mobilization in aerated (97 pct saturated with oxygen) samples appeared to be consistently greater than metal dissolution from stagnant (79 pct or 70 pct saturated with oxygen) waters. In the early weeks of the study, sulfate concentrations increased with solid-liquid contact time, while calcium dissolution remained nearly constant. Metal concentrations varied in relation to solid-liquid contact time and aeration. Leachate pH appeared to be nearly independent of solid-liquid contact time for basic tailings. Reactive tailings having both a submerged and a surface component demonstrated increased metal mobility.

Jan 1, 1990

By J. Desroches, J. Burghardt, N. Whitney, B. Lecampion, A. Surdi, M. Houston, S. Stanchits

There is accepted evidence that multistage fracturing of horizontal wells in shale reservoirs results in significant production variation from perforation cluster to perforation cluster. In fact, only a fraction of the perforation clusters seem to contribute to production in many shale gas and shale oil plays. In many cases, the orientation of the lateral section of these wells is determined by lease boundaries rather than principal stress directions, and these often do not coincide. When horizontal wells are misaligned from the far-field principal stress directions, the fracture must reorient from the near-wellbore principal stress directions, which are aligned with the wellbore, to the far-field principal stress directions. The primary objective of this study is to learn how various completion designs influence the near-wellbore fracture geometry when such a misalignment exists. A secondary objective is to understand the influence of rock fabric features, such as mineralized natural fractures, on this reorientation process. To understand these effects, eight laboratory hydraulic fracturing tests were conducted using a true triaxial vessel with 914 mm × 762 mm × 762 mm samples of Niobrara shale. Several different completion designs were studied, including the use of fracture initiation slots with several different orientations and the use of perforations selectively located to encourage a smooth transition from the near- to far-wellbore region. The tests were carefully scaled as accurately as possible to provide insight into the field near-wellbore phenomena. Pressure and fluid flux at the wellbore, deformation of the block, acoustic velocity, and induced acoustic emissions were acquired during the tests. Additionally, sized particles were also injected to gauge the fracture width away from the wellbore. After the test, the blocks were dismantled, and the fracture geometry was mapped in 3D. These measurements allow one to clearly differentiate the fracture initiation and the breakdown—meaning the peak pressure—to be clearly differentiated; the fracture was already well developed when the maximum pressure was reached. The study reveals non-negligible tortuosity and aperture restriction in the near-wellbore region. In the field, this would translate to high treating pressures, uneven proppant distribution, and possibly near-wellbore screenouts. The test results show that, of the configurations tested, the best approach is to use deep slots that are aligned with the far-field principal stress directions. The oriented perforation design did not achieve the simple, smooth transition that was hoped for, and instead produced multiple competing near-wellbore fractures and considerable tortuosity. The study also demonstrated that the presence of planes of weakness, such as mineralized natural fractures, near the slot tip can result in poor near-wellbore fracture geometries, even for the best completion configuration. We conclude from these tests that the misalignment of the well with a principal stress direction creates near-wellbore complexity that, in turn, creates uncertainty in proppant distribution and, therefore, production; proppant might avoid up to a half of the created fracture. Regardless of the wellbore orientation, this uncertainty is further increased by the presence of mineralized features in the rock fabric that can strongly alter or stop the growth of the hydraulic fracture. Preventing those effects by changing the completion alone proves difficult, and new strategies are required to ensure a reliable stimulation of shales.

Jan 1, 2015

By S. Parada, P. T. Jones, M. Guo, S. Smets

The corrosion behaviour of a high-quality rebonded magnesia-chromite refractory in contact with a vacuum oxygen decarburization (VOD) slag with high Al2O3content (15?20 mass per cent) is investigated under VOD process conditions by rotating finger tests in a vacuum induction furnace. The refractory degradation mechanisms are studied by the characterization of corroded microstructures using scanning electron microscopy, equipped with energy dispersive spectroscopy. The influence on the refractory wear of the process temperature and the Al2O3content in the slag is discussed. Keywords: corrosion, magnesia-chromite refractory, VOD slags, vacuum induction furnace

Jan 1, 2004

By Venda Oliveira P. J., Correia A. A. S., Danisi C. M.

"AbstractA laboratory study has been undertaken to establish common understanding of the creep phenomenon of a Portuguese soft soil chemically stabilised with binders. In order to study the effect of different stress levels on the strength and on the creep behavior of the stabilised soil, oedometer creep tests and unconfined compressive tests were performed at different curing times. Results show that the creep stress level does not influence the unconfined compressive strength. In addition, the creep phenomenon increases the unconfined compressive strength of the treated soil. Two different secondary compression indexes were recognized from the one-dimensional compression curve which increase with an exponential trend with the creep stress level.IntroductionConstruction on soft soils requires a mandatory soil stabilization work to improve mechanical characteristics of the natural soil. Deep mixing method is a worldwide employed ground improvement method, nevertheless the creep phenomenon hasn’t been yet thoroughly analyzed. Most of the published papers have focused on the analysis of the compressibility and the strength of the soil-binder mixtures without considering the creep phenomenon. However, numerical results (Venda Oliveira et al. 2009) have shown that although settlements that occur during the creep stage (namely creep strains) are less in case of treated columns, they are still important especially due to the high loads applied to the stabilised soil. The few published studies about creep behavior of soil-binder mixtures reveal that the stabilization of an organic soil with cement induces a reduction of creep deformations, which is related to the amount of cement used and that the increase of the organic matter of the soil has a negative impact on soil stabilization, further inducing a slight increase in the creep deformations (Venda Oliveira et al. 2012).As part of the current research the effect of different stress levels on the creep behavior of a soft clayey-silt soil was studied. The binder mixture used to enhance the properties of the soil had a specific composition and quantity. Unconfined compressive strength tests (UCS) and UCS creep tests were carried out at pre-set curing times in order to analyze the creep behavior of the soil-binder mixture. In particular five different creep stress levels were studied to understand its influence on the strength and on the compressibility of the stabilised soil. In addition, considerations about the secondary consolidation index are also presented."

Jan 1, 2014

By Fumihiko Sumiya, Kunihisa Katsuyama, Yuji Ogata, Yukio Kato, Yuji Wada, Yoshikazu Hirosaki

Smooth blasting technique is widely applied for tunneling road or railway construction in Japan. However, smooth blasting technique often causes problem related to detonation failure in explosive column due to channel effect. Channel effect is attributed to the precursor air shock wave (PAS), which propagates ahead of detonation front in an air channel of borehole. PAS precompresses and desensitizes the unreacted explosive column. The failure of detonation propagation occurs as a result. It was concluded in our previous work that reducing PAS velocity was one of the effective methods for the prevention of channel effect.

Jan 1, 2003

The effect of long term exposure of full size bolts to corrosive environments is presented. A special test rig was used to test four bolts under different loading conditions. Four, X-grade identical profile bolts, each of 21.7 mm core diameters (23.7 mm full diameter) were subjected to prolonged corrosion testing using acid sulphate water. The pH value of the circulated water varied between 3.4 and 4.3. The corrosion exposure test period lasted three and half years. Two bolts were axially loaded to 10 and 20 tonnes force respectively, the third bolt was subjected to a 360 Nm torsion load and the fourth bolt was left unstressed to act as a reference bolt. After the test period ended, the bolts were stripped of their corroded coatings and weighted for weight loss. The diameter of each bolt was subsequently measured, and the loaded bolt samples were first tested non-destructively for tensile cracks and then tested for tensile failure. No cracks were found on post corrosion bolts tested non-destructively. The failure strength reduction on all four post-corroded bolts was significant, varying between 21% and 39%. The onset of corrosion was not confined to the targeted mid-section length of the bolt, however, the severest corrosion occurred at the anchored ends of the bolts.

Aug 1, 2013

By S. P. Godby, S. P. Sharples

Wind-tunnel tests were carried out of the conditions under which nuisance dust particles (100-1 000 micrometres) become entrained by wind. A laser entrainment monitoring system (LEMS) was used, and was found to provide an accurate means of assessing nuisance dust emissions from a surface. Accurate determination of the threshold entrainment velocity of dusts using the LEMS gives a baseline against which the performance of dust control techniques can be evaluated. Minerals tested included coal, petroleum coke, limestone, sand and pulverised fuel ash. Pilot field trials of a portable wind tunnel equipped with the LEMS have been successfully completed, providing a means of validating laboratory results in the field

Jun 19, 1905

By Nobuharu Isago, Atsushi Kusaka, Kosuke Kawata

"Strong earthquakes occur frequently in Japan, and some rock tunnels have sustained severe damages on their permanent lining. Many road tunnels, which were constructed by conventional steel arch support and timber lagging method, exist in Japan and they need risk mitigation measures against earthquakes as per our empirical knowledge. Many reinforcing measures for deformed tunnels that may be effective against earthquakes are developed; however, behaviors during earthquakes are not fully understood.In this study, static loading tests and numerical analysis, which simulate a loading condition during earthquakes, were carried out to clarify the effect of the countermeasures. The Load-bearing capacity is estimated for the tunnel structures facilitated by the installment of an inverted arch; however, a joint between inverted arch and sidewall become structural weakness. Rock bolts and carbon fiber sheets have a potential able to mitigate the risks of collapse of the lining by the forces from an earthquake.INTRODUCTIONA number of rock tunnels with no apparent unfavorable ground conditions suffered severe damage, including the collapse of their permanent lining, in large seismic events such as the Chuetsu Earthquake in 2004 (e.g., Mashimo 2005). Since these tunnels were considered to exhibit the required structural strength to survive earthquakes, studies are being carried out to clarify the mechanical behavior of tunnels during earthquakes and their damage mechanism (e.g., Kusaka et al. 2009); however, the aseismic design methodology for mountain tunnels has not yet been established.In many cases of earthquake-damaged tunnels, some defects already existed, such as improper construction and deterioration of lining concrete. Although countermeasures are usually implemented against such problems, their earthquake-resistant effect was not fully understood.In this study, static loading tests and numerical analyses to reproduce these tests were carried out assuming that a rock tunnel was affected by the earthquake to clarify the mechanism of the lining damage and the effect of the countermeasures."

Jan 1, 2016

By Alberto Oalvez, Lucya Yunus, Pengfii Tan

"Laboratory flotation tests of slow cooled converter slag have showed that 92.5% copper recovery at the copper cut-off grade of 24 - 25 % can be achieved by using a 50:50 ratio of DSP330 and SIBX (sodium isobutyl xanthate) at the natural pH of 7 and with a grinding time of 18.5 minutes. 70ìéç is the P80 achieved at this grinding time. MIBC is the frother and the solid content of the flotation feed was 46%. In the plant trials, two types of collectors at two different feed particle sizes for both the normal and slow cooled slag were operated. The particle size was controlled by the feed rate. The P80 of 75 ìçé at a feed rate between 32 - 36 t/h were tested. The plant trials have demonstrated that the copper recovery in the milling and flotation process of the slow cooled slags was improved by 3%. IntroductionIt is proposed to float the slow cooled converter slag, in the auxiliary circuit of the copper concentrator at Mount Isa, by using the processing conditions identified from several laboratory flotation tests. Among these laboratory tests, one produced a copper recovery of 4 % higher than those achieved from a normal cooled slag with the same slag feed grade and the same copper content (24 - 26 %) in the concentrate. These test conditions were selected for further studies.Laboratory Test Work and Plant TrialsThere has been a lot of work conducted under laboratory and plant conditions [1]. However, the achieved results did not justify their total implementation in the Mount Isa Copper Concentrator. Initially, the lab trials were carried out with slag cooled 100% in air; then it was changed to combined cooling for 12 h with air and 2.5 days with water sprays. The reason for this change was the shortage of space when the slag was cooled 100% in air, as it takes several days to achieve safe temperatures for its removal. The San Manuel Copper Smelter has reported that their slag was left for air cooling in pits for 8 h and then was followed by water cooling for 2-3 days [2]"

Jan 1, 2012

By Bawden WF, Paynter JT

This investigation involves laboratory testing and stability analysis of paste fill at the Golden Giant Mine. Site-cast samples are tested in unconfined, confined, and consolidated-undrained triaxial compression. Pore pressures during shear and consolidation characteristics are measured to determine both drained and undrained shear strength parameters and assess the potential for undrained loading. Liquefaction potential is also considered. A limit equilibrium solution is used to obtain factors of safety against failure of the fill during mining of adjacent stopcs

Jan 1, 1998

By Barbery G., A. Maachar, M. Bourassa

Laboratory testing for flotation circuit design is carried out on a routine basis in a large number of lab- oratories throughout the world. Usually a sample of ore, assumed to be characteristic of the material to be processed in a future plant, having a mass of the order of a few kilograms, is ground in a batch ball or rod mill, in the presence of water and some re- agents (for pH control, etc. .. ); after dilution to the adequate solid concentration, the resulting slurry is transferred into a laboratory batch flotation machine, having a volume which can vary from 0.5 to 8 10 -3m3. Various types of machines are in common use, manufactured by the same companies that market industrial size flotation machines. The operation of flotation in the laboratory is carried out by an experienced technician, who uses parameters such as impeller rotation speed, air flowrate addition, froth height, froth removal rate, in conjonction with reagent addition sequence, to "test" the ore. After flotation, the froth products ("concentrates"), and the solids remaining in the cell are filtered, dried, and analyzed for the various elements of interest. For flotation circuit design, a kinetic test is usually carried out, in which the froth products obtained at various times are collected to assess the time response of the ore in the laboratory machine with the combination of reagents used. Although this description is rather sketchy, it enables to outline some of the major difficulties in using laboratory data for flotation circuit design: 1. ore sample representatively 2. feed preparation procedure (laboratory compared to industrial scale) 3. laboratory procedures (type of ma- chine, type of operation, experimental errors. . . ) 4. flotation machine scale-up 5. flotation kinetic scale-up 6. flotation circuit design using laboratory data These various points will be discussed in the present paper, in order to stress the problem areas as well as possible solutions. ORE SAMPLE REPRESENTATIVITY It has been stated many times that one of the major problem in designing a flotation circuit is the representatively of the sample to be taken. Sampling of an ore body during prospection and evaluation is a specialized field, which has been progress in with the introduction of geostatistics. The application

Jan 1, 1986

"A carefully planned laboratory test program is the foundation for the successful development of a sulfide flotation process. In this paper, the development of a copper-molybdenum flotation process is described. However, the concepts discussed can be applied to most sulfide flotation systems and to many industrial minerals projects as well. Each step is examined, beginning with sample procurement and covering sample preparation, flotation test preparation grinding, scoping flotation tests for reagent scheme selection, rougher flotation parameter evaluation and cleaner circuit evaluation, through to locked-cycle testing and pilot plant design and operation. Ore variability and modeling to determine the response of various ore types to the optimum conditions established is also examined.IntroductionA carefully planned laboratory test program is essential for the successful development of any sulfide flotation process. These programs usually begin with a series of batch tests on several ore type composites to evaluate appropriate reagent schemes and delineate optimum rougher flotation conditions, such as primary grind size, flotation pulp density, flotation pulp pH and retention time. Cleaner parameters such as regrind size requirements, cleaner pH, pulp density and number of stages are then defined. Semicontinuous locked-cycle tests are performed using the parameters established in the batch tests to determine the effect of middling streams recirculation on flotation performance. The data generated and the experience gained in the locked-cycle tests may be used to design and operate a continuous pilot plant if relatively large amounts of concentrate are required for further process development, such as optimization of byproduct molybdenum production from bulk copper-molybdenum concentrate.A comprehensive ore variability program is undertaken to determine the response of various ore types to the optimum conditions established. These ore variability programs often test hundreds of samples in standardized batch rougher and cleaner tests to ensure that the orebody is well understood.This article describes the development of a copper-molybdenum flotation process, but the concepts discussed can be applied to most sulfide flotation systems and many industrial minerals projects. The block flow diagram in Fig. 1 provides an overview of the development process."

Jan 1, 2016

By H Saw, M Cordova

Cemented rock fill (CRF) is often used to support open stope voids. This allows for the full recovery of ore while achieving global mine stability. In such cases, the exposed CRF masses require adequate compressive strength and stiffness to resist the forces and limit the displacement associated with movements in the rock mass surrounding the excavations. The CRF material preparation often involves the use of large particles, either from crushed rock or development mining waste. This means that conventional laboratory samples cannot be readily used to determine the laboratory strength. Consequently, a research project was undertaken to determine the influence of sample size on uniaxial compressive strength. This paper presents the results from CRF samples that were prepared using the same mix design and then cast into moulds with diameters of 150, 240, 300 and 400 mm. The laboratory testing also allowed a better understanding of the effect of particle size distribution upon the overall strength of a rock fill mass. The laboratory results were compared to a database of large-scale results from the testing of fill masses from a number of mine sites.CITATION:Cordova, M, Saw, H and Villaescusa, E, 2016. Laboratory testing of cemented rock fill for open stope support, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 755–762 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By R. A. Allwes

In-plane bending and torsion tests were conducted on full-scale masonry walls to evaluate three post-reinforcement designs. The designs were developed to minimize longwall mine subsidence damage to existing residential masonry foundations. The bending tests show that vertical and horizontal post tensioned tendons significantly increase the resistance of a masonry wall' to in-plane bending. The torsion tests reveal that post tensioned tendons increase a masonry wall's limit of deformation but do not increase its torsional stiffness. The torsion tests also show that the masonry units minimally contribute to the torsional stiffness of a masonry wall.

Jan 1, 1995

By F. L. Wolf

THERE is a tendency on the part of practical foundrymen to accept with reluctance the results of tests on sands, binders, and. such materials made in the chemical laboratory alone. They feel that such tests frequently emphasize and measure properties that are of minor importance and fail to take account of characteristics that are important in determining the value of the material in actual practice. Experience seems to indicate that the most thorough and conclusive, test for any new foundry material is an actual run in the foundry alongside of a standard material of known value. Such a test, however, involves certain difficulties and necessitates certain precautions. It is not always easy to obtain a fair trial for a new material. We all have certain prejudices, which unconsciously affect our judgment to a marked degree. A practical test frequently involves so many workmen, each of whom reacts in a different manner to the test, that; the personal equation becomes very, complex and the true results of the test are obscured. There are times, too, when a thorough experimental trial of a material would interfere too much with the rush of work in a department or would hazard the quality, of the product to such an extent as to make it inadvisable. Under such conditions a laboratory test is advisable before the material is sent into the foundry. These tests should be made as practical as possible and so closely related to foundry practice as to give a true index to the value of a, product for the purpose desired. Core sands and molding sands are as numerous "as the sands of the sea" and vary as much in quality. Old sources of supply are continually failing and new ones must be opened, so that we must continually search for new and better grades of sand. During the past year, the Ohio Brass Co. has developed tests for sands', cores, and binders which bear a close relation to the particular use to which these materials are put in

Jan 9, 1920