Search Documents

By K. Izumi

Ultra-grain refinement and high strengthening of metals by accumulative roll bonding (ARB) was widely reported. However, applications of ARB to magnesium alloys were rather limited. In this study, Mg-9%Li-1%Y sheets were applied to ARB at room temperature. Six 0.5 mm thick sheets were stacked and reduced into 0.5 mm thick by four passes. The procedure was repeated up to three cycles, so that the equivalent strain of 6.2 was applied. The sheets show dual phase structure with a (hcp) and ß (bcc). Grains elongates to the rolling direction with increasing number of ARB cycles. After three cycles, fragmented a grains with average size of about 300 nm are uniformly distributed. After the first cycle, the ultimate tensile strength increases to 180 MPa from 133 MPa, while the elongation decreases, however, still high (26%). The tensile strength slightly decreases by the second cycle and does not change at the third cycle. Meanwhile the elongation increases by the second cycle and the sheets show 41% of the elongation after the third cycle.

Jan 1, 2006

By Guojun Wang, Zejun Chen, Wenchang Liu

Al/Mg/Ti laminated metal composite sheet (LMCS) can combine the merits of each of metal components, and obtain excellent performances. It incorporates the advantages of high strength, light weight, easy melt and atomization, and good space adaptability to substitute for the bumper Al sheet of Whipple shield structure for space debris shield. The Al/Mg/Ti LMCS was fabricated by hot roll bonding technology in a certain sequence. The manufacturing process and parameters were analyzed and studied, including the first rolling reduction, roll boding temperature and stacking structure of each metal. The microstructure of dissimilar metals and bonding interface were characterized and analyzed. The optimized manufacturing procedures and parameters were presented based on the microstructure and mechanical properties of LMCS. The research results offer some guides and references for controlling the shape of bonding interface, optimizing the annealing process, improving the mechanical properties of Al/Mg/Ti LMCS.

Jan 1, 2015

By M. Fairman

The effect of welding speed on the microstructure of friction stir processed (FSPed) AZ31B-H24 magnesium alloy was studied using light microscopy, image analysis, and microhardness tests. The grain size of the magnesium alloy was observed to increase after FSP from about 3.5 µm in the base alloy to about 8 µm in the stir zone. The aspect ratio decreased from 1.60 to 1.55 towards the center of the stir zone. The changes in the grain size and shape caused the microhardness of the samples to drop significantly across the FSPed region from 75 HV in the base alloy to below 55 HV in the stir zone. Decreasing the welding speed increased the grain size due to a greater input of heat energy. The faster heating rate due to the lower welding speed caused a deeper penetration of the annealing effects of FSP. It was also observed that the annealing effects caused by FSP were less pronounced with increasing distance from the interface between the sample and pin tool shoulder. The Hall-Petch type relationship of the micro-indentation hardness as a function of the grain size was observed to hold true after FSP.

Jan 1, 2007

By V. Schwinn, P. Fluess, N. Cauderlier, J. Bauer

From a strategic and economic point of view, the development of fine grain high strength steels for long distance pipelines is intensified world wide to satisfy the demand for natural gas in the future.The project related property profiles based on strength, toughness, crack arrest and sometimes resistance against HIC at defined design temperatures require an effective structural refinement using advanced steelmaking and processing in the rolling mill. The microstructure of modern line pipe steels ranges from ferritic pearlitic to ferritic-bainitic and structures where bainite is the dominant component, possibly upgraded by secondary phases. This paper illustrates microstructures and properties of recent orders on line pipe steels both for onshore and offshore application using different processing routes in the plate mill. Examples will be given for SAWL 485 offshore grades, X65 HIC and X70 HIC onshore grades, respectively. Finally, production results of a recent X80 order will be presented.

Jan 1, 2005

By Sandeep Singh Sandhu, Karanvir Singh Ghuman, Manjit Singh

"Cobalt based super alloy stellite 6 was weld cladded on AISI 304 L stainless steel using SMAW process in order to improve the wear resistance for tyre crusher blades. Microstructure characterization and micro hardness testing was performed on stellite 6 cladding. The suitable parameters viz. 80 Amp current with arc weaving technique was selected by performing bead on plate experiment were further used for depositing multipass multilayer cladding to achieve full filler chemistry at the top surface. Further GTAW process was used for re-melting the top surface of the cladding. Comparative evaluation of the claddings showed that TIG re-melting resulted in increased microhardness and wear resistance in comparison to as cladded specimens even with lesser deposition of material. It was observed that TIG re-melting improved the hardness from 603 HV0.5 kg to 712 HV0.5 kg. Micro structures of stellite 6 contained cobalt solid solution matrix along with inter dendrite chromium carbides which resulted in the increased micro hardness values. Pin on disc abrasion tests were carried out at room temperature and the worn out surfaces were characterized using SEM and EDS.INTRODUCTIONThe crusher blades are used in many industries for crushing various types of material and its wider applications in tyre rubber crushing mills, metal-powder crushers industries etc. Most of the crusher blades are damaged by the wear and impact loading conditions. It is because of metal to metal abrasion and the temperature also plays a vital role in blunting the cutting edges of these blades. The wear is the major cause which leads to loss of material and thus the productivity that can never be recovered (Kotechi et al., 1992). The wear can be reduced by coating of various super alloys which could reduce the behavior of metal degradation even in aggressive environments. Cladding of cheaper low alloyed material with expensive superalloys to enhance the performance of components at low cost has been investigated by many scholars (Deng et al., 2010, Kennametal, 2007, Lolla et al., 2014, Singhet al., 2014, J.N et al., 2003, Ramkumar et al., 2012). Many researchers have reported that cladding is an application of build-up deposits of specialized alloys to resist abrasion, high temperature corrosion and impact loadings. Cladding is used for providing required mechanical strength properties as well as inhibition of oxidation and other corrosive degradation. Coatings are used to protect the heat affected areas like tubes of fluidized bed combustor etc. (Kirchbner et al., 2008, Wang et al., 1994, Hocking et al., 1993, Ananthapadmanabhan et al., 1991, Staia et al., 2001). Coating techniques are widely used for the protection of turbine engine and boiler tubes against high temperature corrosion attack, power generation equipment, chemical process equipment, aircraft engines, pulp and paper processing equipment, bridges, rollers and concrete reinforcements, orthopedics and dental, land-based and marine turbines, ships. Coatings of stellite 6 are widely used in steam turbine blades and boiler tubes for power generation because of an excellent combination of impact, wear and other properties. It can maintain its properties even at high temperature and in harsh environments (Kobayashiet al., 1999, Alam et al., 2009, Munehru et al., 2009). The loading and unloading conditions experienced by the material may induce the surface cracks which lead to its breakage and leaving large pits in the surface (Meng et al., 1995). Many researchers have reported that the properties of cladded layers can be increased by various techniques such as controlling the current variations, dilution, heat input, laser and other re-melting processes, addition of special alloying elements, speed of weldingetc(C.M Anaet al., 2002, Kumaret al., 1999, Luo et al., 2012, et al., Madadi et al., 2011, Shin et al., 2003, Kuzucu et al., 1997, Sudha et al., 2008, Sawant et al., 2017, Houdkova et al., 2016, Ciubo"

Jan 1, 2017

By R. Boom, L. Holappa

In the present paper, microstructure changes of solid-state reduction of industrial chromite pellets and lumpy ore were investigated with SEM/EPMA. To simulate the reactions in the packed bed zone of the Submerged Arc Furnace (SAF), carbon monoxide was used as the reducing agent, with the presence of graphite in proximity to chromite. The experiments were carried out at 1500 °C. Scanning electron microscopy was used to observe and analyse the structure and composition changes of the chromite samples. It was found that reduction of lumpy ore generally took place slower than that of pellet. In all samples, chromite reduction proceeded faster in the outer part of the sample than in the centre part. The reaction mechanism is discussed on the basis of experimental results and earlier investigations. The possibilities to optimize the FeCr production process are also discussed.

Jan 1, 2007

By O. F. Ochonogor

Laser metal deposition (LMD) is an additive manufacturing technique whereby a stream of metal powder is consolidated by a focused laser beam on the surface of a substrate or engineering component. The interaction zone between the laser beam and powder particles is scanned superficially, generating tracks of deposited material. The tracks are overlapped in a deposition strategy in accordance with slices of a CAD model. Successive layers of material are built up to fabricate a near net shape part. In this work, the technique is used to fabricate metal matrix composites (MMCs) by using an elementally blended feedstock combining metal and ceramic powders in the melt pool, which melt and solidify to create the required morphology. Ti6Al4V + TiC MMCs were produced with 10, 20, and 30 vol.% reinforcing ceramic, and Zr + TiC MMCs were fabricated with 10, 20, and 30 vol.% TiC. The deposited thin walls were analysed using optical microscopy, scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS), and indentation testing. In both systems, the analysis revealed the presence of partially melted TiC particles embedded in the metal matrix along with fine dendrites of re-solidified ceramic. The dendritic structures in the Ti-based composites were confirmed as TiC, whereas in the Zr-based composite the Zr metal reacts with theTiC to form ZrC, leaving Ti in solid solution. Both the MMCs show an increase in microhardness with increasing ceramic (carbide)content, reaching a peak HV0.1 value of 500 in the Zr- based MMC and HV0.1 of 550 in the Ti based MMC.

Jan 1, 2012

By S. Yue, P. Vo, M. Jahazi

The flow behaviour and microstructure development of a near-alpha titanium alloy during beta working has been investigated. Typical cogging conditions were simulated through compression testing of IMI834 at temperatures of 1025°C-1100°C, strain rates of 0.01 s-1 - 1 s-1 and post-deformation heat treatments up to 4h. Using a synthesis of available literature models, a finite element model has been developed and validated through quantitative measures of flow stress-strain data and beta grain characteristics. Flow behaviour was analyzed through a self-consistent method while the microstructure development was considered with regard to the kinetics of beta recrystallization. Deformation at beta or high alpha/beta working temperatures (T>l025°C) produced minor flow softening with complete grain refinement achieved through metadynamic recrystallization.

Jan 1, 2006

By G. Avramovic-Cingara, H. J. McQueen

The microstructure of commercially pure aluminum was investigated by using polarized optical microscopy (POM), orientation imaging microscopy (OIM), and transmission electron microscopy (TEM) techniques. Specimens were deformed in torsion at 400°C and equivalent strain rate of 0.1 s-1, to various strains of 0.2, 0.5, 1, 4, and 6. The results indicate that POM can usefully reveal grain and subgrain structures over a large field in aluminum. TEM is most suitable to study dislocation substructure and evolution of subgrains. While TEM microscopy and OIM are capable of resolving individual subgrains, OIM can not reliably distinguish subgrains with small misorientations, particularly in samples with low strain. On the other hand, the OIM technique is very useful in the analysis of many regions surrounded by high, medium, and low angle boundaries (HAB, MAB, LAB). Various misorientation maps were studied using different data processing methods. The analysis revealed that the subgrain size is relatively insensitive to strain. The fraction of low LAB ( < 5°) decreased and HAB (>15°) increased conversely with increasing strain, whereas MAB (5-15°) remained stable. The development of an increasingly bimodal grain boundary misorientation distribution is consistent with the predominance of dynamic recovery (DRV) in the evolution of microstructure, combined with geometrical dynamic recrystallization (gDRX), now called grain-refining DRV.

Jan 1, 2006

By K. Matsuura, M. Ohno, T. Tokunaga

"Recently, weight saving of automobiles has been strongly required to solve the global environmental problems. Mg alloys are one of the promising candidates as a new material for automobile components. However, the application of the Mg alloys is limited due to their poor corrosion resistance. In the authors’ preliminary study, an Al/Mg/Al clad sheet was fabricated by hot extrusion and subsequent hot forging. The clad sheet exhibited a high corrosion resistance and excellent super plasticity. More specifically, the elongation of the clad sheet was as high as 550%.Importantly, despite that the elongation of Al itself was only 40%without cladding with Mg, the ductility of Al was greatly improved in the form of the clad sheet. In the present study, in order to clarify the mechanism of the superplastic deformation of the Al part in the clad sheet, the microstructure evolution of the Al during the tensile de formation is investigated. The tensile tests were conducted at a temperature of 573 K and at a strain rateof1.0×10-3s-1. The Al exhibited fiber-type texture at the beginning of the tensile deformation, and brass-type texture after the elongation of 50%.INTRODUCTIONMg alloys have been gaining attention because of their excellent properties e.g. light weight, good recyclability and high electromagnetic shielding. However, their practical applications have been limited due to their poor corrosion resistance. In the authors’ previous study, in order to solve this problem, Al coating on Mg alloy by hot extrusion has been proposed, and the Al-coated Mg alloy plate was fabricated(Tokunaga, Matsuura, &Ohno,2012). The plate was hot-rolled and an Al/Mg/Al clad sheet was fabricated. No cracks or debondings were observed at the Al/Mg interface. The sheet exhibited a high corrosion resistance in a comparable level as pure Al. Also, the sheet exhibited a large and uniform elongation of 550%in a tensile test at a temperature of 573 K and at a strain rate of 1.0×10-3s-1without any breakings or debondings of the Al part(Tokunaga, Matsuura, &Ohno,2014).Mg alloys have been known to exhibit a superplastic characteristic when the grain size is small. However, it is known that the pure Al does not generally exhibit the super plasticity. As mentioned above, the Al-coated Mg alloy sheet exhibited 550% of elongation in the authors’ previous study (Tokunagaet al., 2014). However, the pure Al itself showed only 40% of elongation, while the Mg alloy itself exhibited 800% of elongation. Thus, it has been demonstrated that the pure Al was super plastically elongated when it was bonded with the Mg alloy. Generally, deformation mechanism of the super plasticity of the Mg alloy is known as a grain boundary sliding. On the other hand, the mechanism of the superplastic elongation of the pure Al is still unclear. The purpose of the present study is investigation of the deformation behavior of the Al part in the Al/Mg/Al clad sheet during tensile de formation."

Jan 1, 2018

By L. A. Matthews

The embrittlement of the Ti-6Al-4V alloy by hydrogen dosing at elevated temperature has been investigated. Metal coupons were subjected to isothermal treatments in a partial hydrogen atmosphere in the temperature range from 650ºC?950ºC and the degree of embrittlement after treatment was determined by drop-weight impact testing. Embrittlement was found to be inversely related to reaction temperature as a result of the combined effects of greater hydrogen absorption and titanium hydride precipitation at the lower isothermal temperatures. Keywords Titanium, hydrogen embrittlement, impact energy

Jan 1, 2011

By Timothy W. Skszek, Adrian S. Sabau, Hebi Yin, Xiaoping Niu

The microstructure evolution during solution treatment plays an important role in mechanical properties of heat-treated aluminum alloys. In this paper, models were reviewed that can predict the microstructure evolution during the solutionizing process of the aging heat treatment of aluminum alloys. The dissolution ofMg2Si particles has been modeled as a diffusion process of Mg in the a-Al matrix. The evolution of volumetric fraction of fragmented silicon as a function of time and temperature was also considered. The growth and coarsening of silicon particles during the heat treatment was considered. It was found that constitutive equations and required property data for most of the phenomena that need to be considered are available. Several model parameters that need to be obtained from material characterization were identified. Pending the availability of these model parameters, this comprehensive model can be used to describe the microstructure evolution of aluminum alloys in order to optimize the solutionizing heat treatment for energy savings.

Jan 1, 2013

By D S. Clarke, W M. Prebble

Potential waste rock products from the mining of epithermal deposits in the Hauraki Goldfield are characterised to facilitate their management. Hydrothermally altered andesites and their weathered near surface equivalents have been examined from the Golden Cross, Karangahake and Monawai gold deposits. These materials vary in both their clay content (smectite, illite, kaolinite and chlorite) and the degree of silicification resulting from alteration and weathering. The simulated degradation (slaking tests) of waste materials cannot be explained purely by consideration of clay content, siliciflcation, or the resultant variations in porosity. &nbsp; Microstructure is considered to be essential in predicting the physical degradation of waste rock. The scanning electron microscope is an effective tool in such an investigation. Increasing alteration results in clay particles becoming more randomly orientated (matrix microstructure); this causes a reduction in the surface area of contacts between components resulting in increased potential for degradation. The extent of skeletal microstructure (commonly characteristic of weathering) is an important control on effective porosity and the long term potential for degradation. Management requirements for these materials include the minimisation of moisture content variations (with the prevention of initial drying being of primary importance) and the containment of sediments produced.

Jan 1, 1991

By Yongyong Gong, Qijie Zhai, Zhichen Zhang, Qixin Li, Zhishuai Xu

"Microstructure of semisolid slurry of Al-4.5wt.%Cu alloy was investigated with pulse magnetooscillation (PMO) treatment, the results showed that the PMO treatment can refine the crystal structures of Al-4.5wt.%Cu alloy significantly. The discharging frequency of PMO had a great effect on the solidified structure transformation of semisolid slurry of Al-4.5wt. %Cu alloy, and the primary a-Al particles become much finer and rounder with an increase of discharging frequency. However, over a certain discharging frequency, the grains of primary a-Al become coarse.IntroductionOver the last decade, a lot of attentions have been paid on metal rheoforming process [1-4], since it has higher mechanical properties of formed components, strength to weight ratio and age hardenablity. Nevertheless, semi-solid forming is always performed at high solid fractions (40%-60%), so it has the limitation of viscosity, a tends to be difficult to pour semisolid slurry into the hole of the shot sleeve. Therefore, a series of novel semi-solid slurry preparation methods and rheoforming techniques have been invented, such as, semisolid vibration treatment [5], rheocasting [6], pulsed magnetic field process [7], annulus electromagnetic stirring [8], via ultrasonic vibration process [9], equal channel angular extrusion (ECAE) process [l0] and straininduced melt activation (SIMA) process [11].The electromagnetic field is characterized by its effective grain refinement, green, convenient manipulation and without contamination of melt. The mechanisms of dendrite was fragmentation by electromagnetic field have also been largely proposed [12-14]. The broken dendrite arms then undergo a coarsening process to provide the globular structures and obtain much finer and rounder a-Al particles. When compared with other external electromagnetic techniques, Pulse Magneto-Oscillation (PMO) has obtained more fuvors, owing to narrower pulse width and much lower energy consumption. Furthermore, the PMO treatment can reach finer grains with shorter time treatment [16, 17]. This work aims to study the effects of different discharging frequency ofPMO treatment on the microstructure transition of the semisolid slurry of Al-4.5 wt.%Cu alloy."

Jan 1, 2014

By Kathie Mcgregor, Muhamad Firdaus, Nathan A. S. Webster, Yvonne Durandet, W. John Rankin, M. Akbar Rhamdhani

There is a growing interest in recycling/recovery of rare earth elements from permanent magnets. A number of processing techniques are currently being developed but are highly sensitive to the oxidation state of the material. The oxidation microstructure of NdFeB magnets is studied at high temperatures (773-1173 K) to understand oxide formation mechanisms and support the development of viable recycling strategies.

Mar 1, 2017

By M. A. Neri

A lead-free solder alloy Sn-57.5Bi-0.5Ag has been developed by mechanical alloying and foundry processes, and has great potential as a lead-free solder system, to low temperature applications. The mechanical alloying powders show a microstructure different to the microstructure obtained by the foundry process for the same alloy. Its melting point of 142°C is slightly higher than that of eutectic tin- bismuth solder. Examination of the microstructure revealed that eutectic microstructure is refined by the mechanical alloying process Ag additions. The lamellar structure of tin-bismuth gradually disappeared with the process of mechanical alloying, while intermetallic compounds AgaSn phase was formed. The Cu-Sn intermetallic compound layer formed at solder-copper interface is the Cu6Sn5 phase. Keywords: Lead-free solder, Microstructure. Mechanical alloying

Jan 1, 2003

By Kan Song, Lin Liu, Hengzhi Fu, Jun Zhang, Haijun Su, Xiaojiao Jia

"Al2O3/YAG/ZrO2 eutectic in situ composite has been regarded as new generation of high temperature structural material due to its excellent performance even close to its melting point. The directionally solidified Al2O3/YAG/ZrO2 eutectic ceramics are prepared by recently developed Laser Floating Zone Melting (LFZM) apparatus in which a splitter mirror is used to obtain two beams with the same quality from one CO2 laser. With the two laser beams irradiate the sample from opposite directions, the sample is zone melted. The apparatus configuration and the solidification processing are described in detail. The solid/liquid interface morphology is studied and the mechanism of microstructure formation especially the characteristic of eutectic cellular is discussed. It is shown that YAG and ZrO2 phases play a leading role during the ternary eutectic growth. Meanwhile, the relationship between the solidification microstructure and the processing parameters are investigated.IntroductionAl2O3/YAG/ZrO2 ternary eutectic in situ composite, due to its excellent high temperature mechanical properties, is now considered to be a promising candidate material as a replacement of nickel based super alloy for new generation aero space engine turbine blade [1]. They exhibit flexural strength of 360-500 MPa from room temperature to 2073K in air atmosphere [2]. The compression creep strength at 1873K is 433MPa with the strain rate of 104/s [3]. However, because of the high melting point and complex physical properties, there remain still many difficulties for its application. One of the bottlenecks is the poor understanding of the relationship between microstructure and solidification conditions."

Jan 1, 2012

By Abdelmalek Bouazza, Aamir Mahawish, Will P. Gates

Bio-grouting by means of microbial induced calcite (calcium carbonate) precipitation (MICP) to improve mechanical properties of granular soils has gained much attention in recent years. The biogrouting process offers an alternative and environmentally friendly approach to conventional soil improvement techniques, such as cement. Bio-grouting by urea hydrolysis has been extensively applied to tackle various geotechnical problems. However, it has yet to be applied to improve engineering properties (compressive strength) of a coarse cohesionless material with the aim using it as sand/stone columns within soft and very soft soils. This paper investigates the effect of using light, moderate and heavy biochemical treatments on the unconfined compressive strength (UCS) of coarse sand columns. In addition, the microstructure of the bio-cemented coarse material has been analysed by X-ray computed tomography (XRCT). The experimental results revealed that the UCS could reach up to 200kPa, 1000kPa and 5500kPa for light, moderate and heavy bio-cemented coarse sand columns, respectively. The microstructure investigations showed that the deposited calcium carbonate can be identified using XRCT imaging and can be associated with the gain in UCS values. Various microstructure properties, such as void ratio, dry density and porosity were also identified and compared with the laboratory data.

Jan 1, 1900

By Henry Rawdon

THE METHOD of demonstrating the structure existing in a metal or alloy at high temperatures, by etching a polished sample after it has been heated to the desired temperature, is quite familiar to metallographists. The usual procedure1,2 is to heat the specimen, previously polished for microscopic examination, to the desired temperature, in a neutral atmosphere (hydrogen or nitrogen), then admit the etching gas. (chlorine, hydrochloric acid or similar gas) for. a few seconds, and finally, after flushing out the etching gas with the neutral one, cool the specimen in the neutral atmosphere. The pattern produced by etching at a definite temperature is usually taken as a record of the microstructure prevailing at that temperature. It has frequently been pointed out that changes in composition of the surface metal occur during the preliminary heating in the neutral atmosphere, so that the appearance produced&apos; by the etching at high temperature may not exactly represent the condition of the interior of the specimen. To overcome this uncertainty, the heating has sometimes been done in vacuo,3 the etching gas being ad-mitted when the desired temperature was reached, then pumped out and the specimen cooled in vacuo.

Jan 2, 1920

E. E. THUM,* Salt Lake City, Utah (written discussion?).-While the present paper is confined exclusively to the microstructure of fusion welds, it may be of interest to draw attention to certain appearances existing in resistance welds such as spot or butt-welded joints produced by the Thomson process. For instance, a butt weld between two pieces of carbon tool steel (carbon about 0.90 per cent.) will show concentric ellipsoids of the various materials from pearlite to martensite. The surfaces of demarcation are quite well defined, the center of the ellipsoid being at the intersection of the axis of the piece and the plane of the weld. Often these unannealed welds show a troostitic center; evidently this core was not quenched as rapidly as the surrounding shell. Such specimens are beautiful samples for instruction purposes. An annealed butt weld of this kind will show a very well defined central ellipsoid of decarburized, materials. It is interesting to consider the reason why this change takes place. It must be understood that the heat is on the metal for a very short time, possibly 30 sec. It is therefore evident that the decarburization, or migration, of the carbon takes place with extreme rapidity. Since no blowholes are evident in a well-made butt weld, the deoxidizing air and the products of combustion must migrate with the highest speed; second, the carbon might migrate back into the stock; or, last, a large proportion of the pearlite may be extruded with the hot metal, which forms a fin at the plane of weld. Examining these possibilities in detail, it is not probable that such deep-seated decarburization, extending with maximum effect to the very center of a 2-in. round bar, is done by reaction with the oxygen of the air. This would postulate entrance of oxygen and egress of carbon oxides in large quantity without leaving behind traces in the form of oxides or

Jan 5, 1919