Search Documents

GEORGE F. COMSTOCK (author's reply to discussion*).-Mr. Thum's description of the effects of butt welding and spot welding on the micro-structure of steel are interesting and timely. The speed with which the changes noted by Mr. Thum must take place is indeed remarkable, but the writer has noted a similar very rapid diffusion of carbide in annealing a t a rather high temperature certain samples of soft sheet steel containing massive cementite segregated on a small scale. The massive cementite in such steel can be dissolved and distributed very quickly if the proper temperature is attained. Mr. Thum's explanation of the structure he found in the spot welds seems entirely reasonable, but the mystery of the decarburized material in the butt weld is one that might well be the subject of further research. The possibility of decarburization by air ,might perhaps be worthy of a little more consideration than he gives it, for the oxides formed would be gaseous on account of the presence of carbon, and hence not visible in the microscope, and the effect of the pressure might be to squeeze the carbon oxides, which would normally form blow-holes, out of the metal or possibly into such small volumes as not to be noticed The removal of carbon by liquation and squeezing into the fin would be an effect similar to the "bleeding" of a steel ingot that is rolled while the center is still liquid, giving a soft low-carbon interior in the finished section while the segregate was removed in cropping the pipe. This effect in Mr. Thum's butt welds could, however, only be obtained if the weld was heated to near the melting point of the steel, and if the carbon was considerably segregated in the bars at the start, for the first effect of the high temperature would be to promote diffusion rather than the contrary segregation and Equation. It is gratifying to learn from Dr. Ruder's remarks that his researches have resulted in no disagreement with the few points brought out by the writer's experiments. In addition to the three forms in which nitrogen may occur in iron that he mentions, it would seem that a fourth form is often found; This is apparently a eutectoid, like pearlite, and sometimes almost as coarse as the massive cementite seen in soft steel sheets that have been annealed for a long time. One of the things needed in the metallographic study of steel is an etching reagent that will distinguish definitely between nitride in this form and the more common pearlite or cementite.

Jan 6, 1919

By Ravi Vancheeswaran

The consolidation of ceramic fiber reinforced metal matrix composites is a key process step in the synthesis of high performance composite systems. A simulation tool has recently been developed for predicting the evolution of the composites internal state microstructural variables (eg. relative density, fiber microbendinglfracture, and chemical reaction layer thickness at the fiber-matrix interface) during the consolidation processing of spray deposited composite mono-tapes. A Generalized Predictive Control (GPC) scheme is used in conjunction with the simula-tion tool to design near optimal process paths that minimize fiber damage and reaction product thickness while simultaneously maximizing the composites relative density. The microstruc-tural evolution depends nonlinearly on the process conditions and therefore the scheme uses a constantly updated linearization of the model to optimize the input process variable vector. A control simulation is presented to illustrate the performance of the design scheme and to assess the feasibility of its use for the achievement of goal state microstructures at the completion of consolidation cycles.

Jan 1, 1996

By Qiang Yu

This paper reports on a research project supported by NSF, which aims at developing a multi-scale methodology for systematic microstructure prediction in thermo-mechanical processing of metals. This methodology is based on combining mesoscopic microstructure models with macroscopic process formulations and involves the following three main steps: (I) based on the given global processing conditions, the gross deformation patternof the entire workpiece is modeled using a continuum-based algorithm, (2) the resulting parameters are then extracted from the continuum-based simulation, post-processed and passed on to the mesoscopic numerical module, and (3) the microstructural changes are finally modeled at the mesoscopic scale. This approach is expected to overcome the disadvantages of current microstructure prediction practice employing empirical relationships between microstructural features and processing parameters. Keywords: Thermo-mechanical processing, Microstructure, Grain growth; Recrystallization; Mesoscopic models; Finite Element Method

Jan 1, 2003

By S. Becker, M. Gruner

"Microstructure stabilized crushed rock salt is a newly developed backfill material for infrastructural openings in HAW repositories. The motivation for this research is based on the fact that the microstructure stabilized crushed rock salt is considered to be superior to the currently used crushed rock salt. The avoiding of settlements with a simultaneous 100% backfilling of openings, early stabilization of the geological barrier and low permeability (< 10-14 m²) are the main improvements. With the newly developed backfill material, the gap between the crushed rock salt and the saliniferous composite backfill materials is closed. Due to the minimized amount of a binding agent, the material will still be easy to handle like a bulk material, yet guarantees close to 100 % backfill success without any settlements. This is accomplished with a long-term stable re-mineralization that is formed by the components of the binding agent. INTRODUCTION The permanent storage of high active waste in underground geological formations (HAW-repository) is the labored method in Germany as well as internationally. Experiences have been made over the last decades, e.g. in the Waste Isolation Pilot Plant (USA) and the mines Morsleben and Asse (Germany). For this purpose salt formations are preferred as host rock due to the adequate heat conductivity, creep capability, and low permeability. In order to maintain the low permeability of the host rock and to avoid any contact of the stored waste with the biosphere, the formation of flow paths has to be prevented. The cavities which have been mined for the purpose of waste storage have to be backfilled with material that is alike to the host rock. Therefore crushed rock salt is considered as an appropriate backfill material. Crushed rock salt is a bulk material that is produced by mining saliniferous formations. This material is mainly used in underground repositories as a dry backfill that is brought into the cavities by the use of mechanical (loading machine, slinger machine or scraper) or pneumatic energy (pneumatic stowing). In Germany it is intended to use dry crushed rock salt with a maximal grain diameter < 64 mm for backfill in a future repository in saliniferous formations. With this method applied, the porosity of the backfill is up to 35 % [1]."

Jan 1, 2015

Rapidly solidified TiAl-Cr-xNb-Y(x=2,4,6, at.%) alloys have been produced using a single roller melt spinning method. The microstructure of alloy ribbon was refined and component became more homogeneously by rapid solidification technology. There were two phases in alloy ribbons, including -TiAl and 2-Ti3Al phases, yet the amount of 2-Ti3Al phase in matrix obviously increased by rapid solidification than cast alloys. The micro-hardness testing also carried out. Compared to the cast alloys, the alloy ribbons have much higher hardness.

Jan 1, 2009

By S. Amira

In the last two decades, many new creep-resistant magnesium alloys have been developed for high temperatures applications. Their mechanical performance and corrosion behaviour were reported for various experimental conditions. However, these conditions often led to uneven comparison basis. In the present study the microstructure, mechanical properties and corrosion performance of four of these newly developed creep-resistant magnesium alloys were systematically compared. Specimens were obtained from experimental box-like components that were die-cast and thixocast in comparable conditions. Their mechanical and corrosion properties were compared using similar testing conditions. Results show that the creep resistance, strength and impact resistance of specimens are comparable but systematically lower compared to specimens cast under optimized conditions. The reduced concentration of elements such as Al, Ca, Sr and Ce lead to a decrease of the corrosion resistance of the magnesium alloys in 3.5% NaCI solution.

Jan 1, 2007

By D. Sethuram, P. G. Koppad, S. Iyengar, R. Shobha

TiB2 and CeO2 particle-reinforced Al6061 hybrid composites were manufactured using stir casting and hot rolling techniques. The base alloy and composites were hot-rolled at 500ºC and a 50% reduction was achieved through 12 passes. The effect of varying TiB2 and CeO2 particle additions on the microstructure and mechanical properties of the Al6061 matrix was studied. Scanning electron microscopy showed uniform dispersion of both the reinforcements, with good interfacial bonding. Microhardness and tensile properties like yield and tensile strength were found to be higher for hybrid composite with 2.5% TiB2 and 2.5% CeO2 compared to Al6061 alloy and other hybrid composites. The increased tensile strength is attributed to good dispersion and interfacial bonding between the particles and Al6061 matrix. Fracture analysis using a scanning electron microscope revealed ductile fracture for the Al6061 alloy and mixed characteristics of ductile-brittle fracture for hybrid composites

Oct 1, 2021

By Burrows. A.

Temperature profiles in the lead smelter sinter bed at Xstrata Zinc Mount Isa sinter plant have been measured using a wireless temperature probe. Corresponding sinter samples have been collected for characterization. The sinter peak bed temperatures were found to be in the range of 1000 - 1200 °C. Microstructures and softening temperatures of these sinters have been characterised. Strong correlations have been observed between peak bed temperature and peak hood temperature, and between mean sinter softening temperature and peak bed temperature. It was found that higher peak bed temperature results in higher sinter softening temperature. For the feed material used in the trials, to obtain sinters with mean softening temperatures above 1050 °C, peak bed temperatures above 1130 °C are required. There appears to be a direct correlation between granule size distribution in the feed and peak bed temperature attained. High peak bed temperatures are observed in sinters with narrow granule size distribution.

Jan 1, 2008

By Baoxiang Zhang, Jing Zhang

"As extruded Mg-9Zn-0.6Zr-2Er magnesium alloys were hot-rolled at 400°C, followed by solution treatment at 400 °c for 1. 5h and artificial aging at 200°C for 10h. Microstructures and tensile mechanical properties of the alloys after hot rolling, solution and aging treatment were examined respectively. Optical micrographs of the as-rolled and as-solution alloys showed fine grain structures, due to the formation of Er-and Zn-bearing compounds at grain boundaries which obviously improved the thermal stability of the alloy. Yield strength as high as about 335 MPa was obtained for the as-rolled alloy, showing that the mechanical properties of the alloy was greatly benefit from the grain refinement and dynamic precipitation of fine MgZn2 during hot rolling. Due to solution heat treatment, vast majority of the Mg-Zn phases dissolved into the matrix, and precipitated out again as fine dispersoid during the subsequent aging, resulting in an enhanced aging-hardening effect.IntroductionWith high specific strength and low density, magnesium alloy has stimulated significant interest for the applications in microelectronics, aerospace and automobile industries. Due to its HCP structure, magnesium alloys exhibit relatively poor strength and ductility. Great efforts have been made to improve the properties of magnesium alloys.Thermo-mechanical processing which combined with subsequent heat treatment can strengthen magnesium alloys due to the strain-hardening mechanism, homogeneous distribution of second particles and grain refinement [1, 2]. However, commercial wrought magnesium alloys have high tendency of grain growth at high temperature due to lack of effective solutions to stabilize the microstructure [3, 4, and 6]. But Magnesium-RE alloys containing high rare earth were reported to have remarkable thermal-stability, Rare earth (RE), such as Y, Nd, Yb, Gd, Ce, were known to form second-phase particles that have higher thermal stability combining with Zn and matrix in Mg[12-17]."

Jan 1, 2012

By S. K. Varma, Miriam Regalado, Daniel Salas, Erica Corral, Erika Esquivel

"Age hardenable 2014 aluminum alloys and composites containing 0.10 and 0.15 volume fractions of alumina particles (VFAP) have been solutionized at 540 and 550°C for up to 20 hours. The solutionized samples, heat treated for 5 and 20 hours, have been subjected to room temperature rolling until cracking develops. The work hardening curves have been compared to determine the effect of solutionizing time on the rolling characteristics from both hardness and the microstructural evolution points of view. Solutionizing at two different temperatures results in differences in the extent to which the composites can be rolled until fracture. The microstructural characterization by TEM has been performed to understand the room temperature rolling behavior.IntroductionThe effect of solutionizing on the age hardening response of 6061 and 2014 aluminum alloys and composites reinforced with 0.10, 0.15 and 0.20 volume fractions of alumina particles (VFAP) have been reported in the literature [1-4]. A comparison of the monolith and composites indicates that particles promote the aging process through differences in the microstructures in solutionized condition. The first effect of solutionizing is to produce a grain growth process which follows a grain growth law (square of grain diameter as a function of solutionizing time). It appears that it is possible for vacancies to be emitted during grain growth period as they try to minimize the total grain boundary surface area by increasing their diameter. This may be common to both the monolith and the composites. However, the second effect must be exclusively considered for the composites. The particles generate dislocations during the solutionizing process due to the differences in the values of the coefficient of thermal expansion (CTE) between the particles and aluminum base metal. It has been determined [1] that the dislocation density increases with increase in solutionizing time in the composites of 6061 aluminum alloys reinforced with 0.10, 0.15 and 0.20 VFAP. The improved bonding between particles and matrix can give rise to additional generation of dislocations due to curvature effects [1] with the result that the dislocation density continues to increase with increase in solutionizing time even after the CTE effect is considered to have been stabilized."

Jan 1, 1998

By Strathmore R. B. Cooke, Thomas E. Ban

MUCH experimental work has been performed on the mechanism of agglomeration and pelletizing of moist ore and concentrates and on the process of firing agglomerates, but except for the work of Tigerschiöld and Ilmoni1 much of the published information is empirical, and the literature contains no information concerning the structure of fired pellets. Results of a preliminary study of the microstructures occurring in pellets produced both in the laboratory and on a pilot-plant scale are presented in this paper. Most of the results were obtained from pellets prepared from Mesabi magnetic taconite, but through the courtesy of the staffs of the Minnesota Mines Experiment Station and the Bethlehem Steel Co., fired pellets produced from limonite and hematite ores and from Lebanon magnetite have also been examined. The work has been restricted almost entirely to pellets produced without additives, the exceptions being those in which coal was. added to the filter cake before rolling. Schwartz has described the microstructures occurring in ore sinters produced under reducing conditions.2 Many of the structures and constituents he describes are common to fired pellets, but the constituents normally occur in markedly different proportions. His statement that "in all satisfactory sinter the amount of hematite is small, perhaps not over 2 or 3 per cent" is inapplicable to pellets produced by pilot plant operation or by any process in which air is not deliberately excluded. Pilot plant pellets contain over 90 pct by weight of hematite, and those produced in the smaller furnaces of the Minnesota Mines Experiment Station contain more than 80 pct of that constituent. Preparation of Specimens It is difficult to examine unfired pellets microscopically because of their insufficient coherency to withstand sectioning and polishing. Fired pellets sometimes lack coherency and frequently contain holes which are troublesome during polishing. Impregnation of both air-dried and fired pellets is readily accomplished by the use of methyl methacrylate monomer.3 The dry pellets are covered in a test tube with excess monomer, to which a small amount of accelerator has been added. When the test tube is placed in a cooling bath and evacuated with an aspirator, most of the entrapped air is removed, and disruption of weak pellets by boiling of the monomer is reduced to a minimum. Polymerization is then effected by immersion of the test tube in a water-bath at about 45°C, this temperature being held for 4 or 5 days. The test tube may then be broken away from the solidified mass and the pellets sectioned by a carborundum wheel or a diamond saw. Where time is important, impregnation is carried out at a higher temperature by Meyer&apos;s method.4 Air-dried pellets must be impregnated with especial care; otherwise swelling occurs and the solids are displaced. It is more important to be certain that the monomer forms a reasonably complete network throughout the specimen than that all entrained air is removed, and for this reason the vacuum technique may be omitted. Impregnated agglomerated products and pellets are extremely coherent, section well, and may be polished either by hand or by machine. Hand polishing is not satisfactory for the examination of conditions existing at the boundaries of grains, and for this machine polishing must be used. The Graton-Vanderwilt machine gives excellent results, provided that pressure on the specimen is considerably in excess of that recommended by the manufacturer. Mineralogy of Fired Pellets Only two opaque iron minerals, magnetite and hematite, have been recognized in pellets. The complete identity of these artificial minerals with their corresponding natural counterparts is shown by their mineralographic characteristics and their X-ray structures. Wüstite has not been found. Slag is the most common transparent constituent of fired pellets. Occasionally conditions have been appropriate for the crystallization of fayalite from the slag, and at other times another crystalline sil-

Jan 1, 1952

By Lucy Villena

El presente trabajo se detalla los resultados más importantes de los estudios realizados de la mineralogía (mena y ganga) y microtermometría con el objetivo de caracterizar los flujos mineralizantes y la dirección de la migración de los fluidos mediante los paleoisotermas de la veta 1. La veta polimetálica es comprendida Pb-Zn-Ag compuestas por rocas volcánicas (andesita a basáltica), cuyo control estructural principal está dado por fallas tensionales de dirección NE-SO, causadas por el movimiento sinestral de fallas Chonta y Huachocolpa- Huancavelica. La composición de las menas reconocidas en la veta 1 corresponde a esfalerita, galena, tetraedrita, bournonita, acantita-argentita y calcopirita, en una ganga conformada por cuarzo, calcita, barita, adularia y yeso. En las muestras de la veta estudiada, los estudios microtermométricos fueron realizados en los cristales de baritina, calcita, cuarzo y esfalerita asociada a la mineralización. Se observan inclusiones fluidas bifásicas acuosas (LH2O + v H2O) las cuales poseen al menos tres eventos mineralizantes según temperaturas de homogeneización y salinidad % equivalente en peso, los fluidos mineralizantes son moderadamente salinos, sugeriendo un ambiente de tipo epitermal.

Sep 21, 2015

By Bjørn Eske Sørensen, Kristian Drivenes, Przemyslaw Kowalczuk, Kurt Aasly, Gavyn Rollinson, Ben Snook

Efficient and successful mineral processing is dependent on detailed knowledge of the materials and minerals that are to be separated and concentrated. Common bulk methodologies such as XRD and XRF are fast and easy, and can provide an overview of the mineralogy and bulk chemistry of the material. However, they will not provide any textural information. Knowledge of the often intricate interaction between minerals in seafloor massive sulfide deposits is crucial in plant design for mineral processing. Samples from the Loki’s Castle hydrothermal vent have been characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF), optical microscopy, Scanning Electron Microscopy (SEM), QEMSCAN, Electron probe microanalyzer (EPMA), and Electron Backscatter Diffraction (EBSD). Processing experiments used froth flotation and leaching techniques. The typical line of operation in ore characterization is shown in Figure 1. Mineral processing may be commenced after any stage of ore characterization. However, it is ideal to have completed as many steps in the ore characterization as possible in order to have the most information of the initial feed material. The main economic minerals in the samples are isocubanite (CuFe2S3), chalcopyrite (CuFeS2), and sphalerite (ZnS), with minor galena (PbS) and trace amounts of Au and Ag. The minerals show complex intergrowth textures down to the nanometer scale. These samples exemplify the need for advanced microtextural analyses to adequately characterize ore material prior to processing. The complex textures hamper the use of flotation as an efficient technique, due to the inability to sufficiently liberate the different minerals and problems with selectively floating isocubanite. Thus, leaching was the preferred method for extracting metals.

Jan 1, 2018

By James Carroll, Lance Heyer

This paper describes the shaft design and construction for a 72-inch microtunnel under 14 active railroad tracks in Avondale, Louisiana. Initial shaft design for a deeper tunnel alignment considered secant piles with a jet grout plug. Final design for a shallower tunnel alignment included contractor input with support consisting of braced sheet piles with a jet grout plug. The authors further elaborate on jet grout implementation in very soft organic clay soils and the practical limitations of jet grouting. This paper emphasizes how all project participants worked together to utilize value engineering and alternative delivery on a unique tunneling project with a focus on temporary shaft support.

Jun 23, 2024

By Steven W. Hunt, Gregory C. Baker, Glen J. Rorison

Microtunneling methods were utilized beneath pile-supported clarifier basins to replace settlement damaged sludge drain lines at the Jones Island Wastewater Treatment Plant in Milwaukee, Wisconsin. To minimize the risk of blockage and expensive recovery of a microtunnel boring machine against pipe piles or construction debris, a Soltau RVS 80 was utilized. This machine allowed the alignment to be initially bored with guided 114-mm diameter rods to ensure proper alignment and lack of obstructions. Casing pipe was then installed by jacking 1-m long, 305-mm diameterclay pipe along the rods and behind an auger head. This case history also discusses how 2.4-m diameter precast concrete pipe was used as a one-pass sinking caisson for workshafts and new cleanout manholes.

Jan 1, 2001

By William Reininger

Microtunneling provides a necessary solution for multiple utility crossings associated with the New York Metropolitan Transportation Authority Capital Construction Company?s (MTACC) Eastside Access Project for the Long Island Rail Road. Construction of four TBM tunnels and their approach structures at the eastern end of the project in Sunnyside, Queens required significant modification and expansion of the railroad infrastructure at this location. Maintenance of railroad traffic during project construction is a principal requirement. As a consequence fourteen (14) utility crossing segments are being installed under active traffic by microtunneling methods. Microtunnels were installed in a variety of conditions including depths, types of soils and construction restraints.

By D. Craig Camp

Microtunneling has successfully completed both horizontal and vertical curves. This paper covers the historical development of curved microtunneling and a description of one microtunneling project. The completed microtunnel is used for electrical transmission in Japan. The crossing had several concerns including right of way, social disruption, obstructions, the cost of intermediate shafts, and political restrains. In order for this drive to meet all of the imposed restrictions, four horizontal curves and one vertical curve were planned and executed in accordance with the design. Iseki Poly-Tech of Tokyo, Japan designed and built the microtunneling machine to meet the project requirements. Curved microtunneling has been successfully used on fourteen projects in Japan. The reason for a curve has been that the project could not be rerouted, short straight drives could not be used to negotiate the curve, or the project’s social and environmental conditions required a curved tunnel. The following table (Table 1) includes summary information on 14 curved microtunnling projects that have been successfully completed in Japan. The first column is a reference number. Columns two through four include basic project information. The fifth column is the total project distance completed by microtunneling. The sixth column is the project’s microtunneling duration. The seventh column is the machine type and size. All of the machines listed are manufactured by Iseki Poly-Tech of Tokyo, Japan. The size is the internal concrete pipe diameter; all of the projects listed were completed with Japanese standard concrete pipe. The eighth column contains a general description of the soil. The soil type and blow counts are approximately equal to ASTM D 2487 standards. The ninth column lists the radius of the curve and the span distance or the distance microtunneled that included the curve. The radius of a vertical curve is denoted with a “VR”, a span with both a left and right hand curve is denoted with a “S”. Other significant first events are also noted in this column. The first curved microtunneling project was completed in 1982 using a conventional microtunneling machine with standard Japanese concrete pipe and a very long radius curve while maintaining grade for the gravity sewer. The second curved microtunneling project included multiple radii curves, all in the same direction, on a single drive. In 1989, on the fifth curved microtunneling project, a “S” curve was successfully negotiated. On the seventh curved microtunneling project, completed in1995, a tight radius curve was negotiated. In 1996, the eighth project included a vertical curve. The thirteenth curved microtunneling project, completed in 1997, was the first project to utilize a microtunneling machine specifically designed to negotiate curves. The fourteenth curved microtunneling project was the accumulation of all

Jan 1, 2001

By Amanda Powers, Brian Glynn, Robert Sauceda, Daniel Huffines, Mike Garbeth

This paper will review the evaluation performed for the Cottonwood & Hackberry Creek Wastewater Interceptor Improvements Project to replace two separate aging and undersized interceptor sewers by either open cut construction or trenchless construction methods. A case study will be discussed for the utilization of microtunneling to avoid a deep open cut excavation within a landscaped roadway median to construct nearly a mile of new 60-inch interceptor sewer in an urban area adjacent to an environmentally sensitive riverine area, while minimizing the permitting and environmental impacts of construction, and minimizing the impacts to residents and vehicular trafc and restoration reuirements.

Jun 23, 2024

By Kimberlie Staheli

A new sanitary sewer was installed in Pleasant Hill, California using microtunnelling methods. The project consisted of 693 meters of 1372 mm and 1981 mm concrete pipe. A Herrenknecht AVN 1200 was used to install the nominal 1372 mm pipe in three drives. The machine was then fitted with an oversized shield used to install the large diameter pipeline. This articulated shield allowed the excavation of a 2362 mm diameter hole with a 1524 mm machine-- a technique new to North America. This paper reviews the design considerations for the articulated shield and reports on the project challenges and solutions to overcome these challenges.

Jan 1, 1995

By Michelle L. Ramos

INTRODUCTION The Ballard Siphon was built in 1935 and consists of two 91.4 cm (36-inch) diameter wood-stave pipes. These pipes convey sewer flowsunder the Ship Canal from northwest Seattle and the Ballard Regulator to the North Interceptor and the West Point Treatment plant. The siphons were constructed using open cut construction, are now buried in the sediment on the floor of the canal, and have severely limited ability to be dewatered, inspected, or cleaned. The existing siphon is 394.7 m (1,295 feet) long from the junction structure on the southern shoreline to the regulator structure on the north. The location of the Ballard Siphon is shown in Figures 1 and 2. The area around the Ballard Siphon has become more populated and developed since the siphon was built. Additionally, the Ballard Siphon is subject to high flows that are greater than the capacity of the pipelines. This has resulted in predict-able Combined Sewer Overflows(CSO?s) whenever a large, long duration rain event occurs. The aged pipeline of uncertain viability has become a critical piece of the sewer system infrastructure. Because of the age of the pipelines and their importance, a sonar survey was completed on both barrels of the Ballard Siphon in December of 2005. The sonar images appeared to indicate crown intrusion of the wood-stave pipes, which suggested that the pipes were in imminent danger of collapse. As a result, an Emergency Declaration was executed by King County and the Ballard Siphon Replacement Project was initiated. Staheli Trenchless Consultants was retained to perform feasibility studies to deter-mine the viability of using microtunneling and horizontal directional drilling (HDD) for replacement of the Ballard Siphon. For the evaluations, the preferred site location was determined to be at or near the site of the existing Ballard Siphon in order to minimize the ancillary sewer work which would accompany moving to a new site. To meet flow demands and hydraulic requirements, the replacement siphon needed a mini-mum equivalent diameter of 182.9 cm (72 inches). This could be accomplished with a number of different siphon diameters and configurations including, but not limited to, three 106.7 cm (42-inch) diameter pipelines, two 152.4 cm (60-inch) pipelines, or two 91.44 cm (36-inch) pipelines and a 121.9 cm (48-inch) pipeline.