Search Documents

By D. L. Harris, A. M. Gaudin

Observations were made of the distribution of mercaptan containing S35 between aqueous solution and mineral and between aqueous solution and the gaseous phase. Although equilibrium may not have been attained, adsorption of the reagent was shown to occur reasily from air or aqueous solution on sphalerite, zincite, and willem-ite and to correspond to flotation. Adsorption on quartz did not similarly occur. THE following results, presented here in condensed form,' were obtained in a preliminary study of the adsorption of n-hexane thiol, hexyl mercaptan, on sphalerite, zincite, willemite, and quartz, from aqueous solution and from a gas. Interest in this subject was aroused by a Belgian report' of effective use of hexyl mercaptan for flotation collection of oxidized zinc minerals. The relatively low boiling point, 149°C, of the mercaptan3 suggested the desirability of extending the usual measurements of partition of collector between aqueous solution and gas and between gas and mineral. It is believed that this paper presents the first measurements of this type on a flotation system. Attempts were made to carry out the measurements at equilibrium, but as the work progressed it became increasingly doubtful that this desirable condition had been achieved. To control composition and extent of the gas phase, the apparatus was a wholly-enclosed thermally-controlled glass system. Because of these constraints and the desirability of dealing with pure minerals, a scale of operations was chosen in which a few grams of deslimed mineral were used in each test. It was also necessary to choose a particularly sensitive method for mercaptan analysis, and in fact a method that would permit the experimenters to follow the approach to equilibrium. For these reasons mercaptan marked by radiosulphur 35 was used. An analysis was made for the radiosulphur by a modification of the method of Gaudin and Carr. Coarsely-crystallized sphalerite was handpicked, stage-crushed in the dry state, wet-screened on a 200-mesh sieve, and deslimed in water at about 5 microns. Further treatment consisted of a wash in dilute aqueous hydrogen peroxide, drying, removal of the dark-colored fraction in a Frantz magnetic separator, washing in very dilute hydrochloric acid, repeated washing in distilled and conductivity water, and drying. The last washings showed a conductivity equivalent to a few ppm NaC1, that is, much more than would be provided, theoretically, by a saturated ZnS solution. The material was stored dry in sealed bottles. Analyses were as follows: Zn, 62.3 pct; Fe, 0.43 pct; Cd, 0.44 pct; S, 31.2 pct; Mn, 0.001 pct. The specific surface (BET method) was 2000 cm2/g. Zincite from Franklin furnace of the New Jersey Zinc Co. was hand-picked, dry-crushed, wet-screened at 100 mesh, and deslimed at about 10 microns. After drying, the associated zinc, manganese, calcium, and silicate minerals were removed in a Frantz magnetic separator. The purified zincite was washed in distilled water and conductivity water to a conductance of less than 2 ppm equivalent NaC1, dried, and stored. Analyses were as follows: Zn, 75.1 pct; Fe, 0.9 pct; Mn, 2.78 pct. The specific surface (BET method) was 1740 cm 2/g. Willemite, also from Franklin furnace, was purified similarly. Analyses were as follows: Zn, 52.5 pct; Fe, 0.12 pct; SiO², 27.3 pct; loss on ignition, 0.13 pct. The specific surface was 1760 cm 2/g. Conductivity water (double-distilled) and demin-eralized-distilled water were used in most of the tests. The specific resistance was not less than 600, 000 ohms, and usually above 1,000,000. Radiosulphur-marked hexyl mercaptan (1-hexane thiol) was synthesized by Tracerlab, Inc., Boston. Two lots were secured several months apart. The last lot, consisting of about 0.5 g of the mercaptan, had a total activity of about 10 millicuries. Tracerlab Co. guaranteed only the activity; hence a quasi -vapor pressure determination (based upon an S analysis) of the mercaptan was made. The calculated value, 4.2 mm of mercury at 25.5' C, has been compared with that of a sample of Highest Purity 1-hexane thiol from Fisher Scientific Co. The latter had a vapor pressure of 4.5 mm of mercury at 2.5 C. Analytical Procedures The sample containing radiosulphur-marked mercaptan was oxidized to convert the mercaptan sulphur to sulphate, carrier barium sulphate being added to provide a suitable quantity of total barium sulphate in a filter cake. The precipitate was filtered and dried, and counting was carried out either in a streaming-gas (Q-gas) counter for high sensitivity or with an end-window G-M counter for convenience. The oxidized and precipitated mercaptan gave a radioactive count of 65 counts per minute per microgram in the end-window Geiger-Mueller counter and 1100 counts per minute per microgram in a Q-gas counter. For standardization of the mercaptan solution, 15 replicate analyses were made. The average deviation per measurement was about 1600 cpm in 65,000 cpm, the probable error in the mean being 275 cpm. It

Jan 1, 1955

By S. R. B. Cooke, S. W. Clark

Adsorption of calcium and magnesium by quartz was determined over a wide pH range using flame photometry for solution analysis. A parallelism was noted between calcium adsorption at alkaline pH and flotation of activated quartz by means of various fatty acid collectors. Abstraction of calcium from 100 ppm solutions increased above pH 10.5 until all of the calcium was removed at pH values between 12 and 12.5. Calcium was desorbed from the quartz over the pH range 12.5 to 13.0 and returned to the solution. Precipitation of magnesium hydroxide prevented measurement of magnesium adsorption above a pH of 9.9. A calcium adsorption isotherm determined at pH 9 matched measurements of barium adsorption by other investigators over the range where adsorption corresponded to the equation of a Freundlich adsorption isotherm. In accordance with the Gouy-Chapman theory for adsorption in the diffuse layer, adsorption of the divalent cations under these conditions was four times the adsorption of monovalent sodium. Activation of quartz by multivalent metal cations in flotation using anionic collectors has been studied by many investigators. The occurrence of activator cations in the water of flotation mills makes depression of silaceous gangue very difficult. Alternatively, in some flotation systems it is practical to cause activation of quartz so that it is floated from the desirable mineral values. The present study was initiated to investigate the activation of quartz by measuring adsorption of calcium and magnesium ions as a function of solution pH. Early empirical tests showed that quartz would be activated to flotation using anionic collectors if any of a number of divalent or trivalent metallic cations were present in the pulp.1*2 Subsequent studies by Clemmer,3 Cooke and Digre,4 Cooke,5 Schuhmann and Prakash,6 and Cooke, Iwasaki, and Choi,7-8 showed that flotation depended strongly upon the alkalinity of the flotation pulp, the concentration of the activating cations, and the chain length and structure of the organic collectors used. The concept of the electrical double layer has been applied to the case of the quartz-aqueous solution interface by Gaudin and Fuerstenau,9-10 and by de Bruyn 11 to explain the activation of quartz by multivalent metal cations. Studies of the surface of quartz by Gaudin and Fuerstenau9,10,12 and by Li " using the streaming potential technique contributed much information on the electro kinetic condition of the surface of quartz in the presence of various organic and inorganic ions. Measurement of adsorption of ac-

Jan 1, 1969

By A. M. Gaudin, J. G. Morrow

FLOTATION requires the existence of a definite contact angle. This contact angle, the surface tension of the solution, and adsorption at the solid-fluid interface are quantitatively related. Adsorption of dodecylammonium acetate on hematite was measured for a wide range of concentrations of reagent in solution. Similar measurements for quartz have already been made. Contact angle measurements were then made on polished surfaces of hematite and of quartz immersed in aqueous dodecylammonium acetate solutions, and a functional relationship was sought between adsorption density at the mineral-solution interface and the contact angle. Finally, the surface tension of the aqueous amine acetate solutions was measured. These data were combined to give an evaluation of the work of adhesion for the three-phase system. Specular hematite was crushed and then ground dry in a laboratory porcelain mill, with flint pebbles, to pass a 200-mesh screen. The ground product was sized in a Haultain infrasizer, and one of the granular sizes (cone No. 3) was used in all adsorption tests. A hand magnet was used to remove magnetite and abraded iron. Quartz was removed in a Frantz isodynamic magnetic separator. The purified hematite was leached in aqua regia, washed with distilled water until the washings appeared free of electrolyte by conductance measurement, dried in a low-temperature oven, and stored in a pyrex container. The specific surface of the closely sized hematite was determined by the krypton gas adsorption method.' Three measurements gave an average value of 1350 sq cm per g. Chemical analysis showed Fe -69.37 pct, insol = 0.72 pct. The quartz used in the flotation tests had been prepared by Chang" for an earlier investigation. Demineralized distilled water was used for all test solutions. Dissolved salt content was of the order of 0.03 ppm, expressed in terms of sodium chloride, as estimated from conductance measurements. Dodecylammonium acetate was obtained from Armour & CO. in two forms, the unmarked compound and a preparation marked by carbon 14 in the hydrocarbon chain of the aminium ion. Specific activity of the active salt was 0.134 millicurie per g. The important physico-chemical constants for the primary amine salt have been reviewed by de Bruyn. The calculated effect of hydrolysis of amine salt on pH of aqueous solutions and the effect of pH on the distribution ratio of the alkylammonium ion to free amine are of particular interest. All other chemicals used in this investigation were of analytical reagent grade. A column method' was used for adsorption work. Attainment of equilibrium distribution in the adsorption column depends on the solid-solution contact time, hence upon the volume of solution passed. It was assumed that contact time required for equilibrium would be a maximum for the lowest reagent concentrations. On this premise it was demonstrated experimentally that the passage of 500 ml of solution through the mineral bed was adequate. An aliquot (1 to 5 cc) of the solution to be analyzed was transferred to a small pyrex cup and allowed to evaporate to dryness at room temperature; 4 or 5 mg of unmarked amine acetate were added to the dried sample and the cup and its contents were transferred to the combustion system for analysis. Evaporation at room temperature must be emphasized, as even slightly elevated temperatures result in loss of reagent. A laboratory model G Beckman pH meter equipped with a glass electrode was used to measure pH of amine acetate solutions. The technique of internal gas counting of radioactive carbon dioxide in a Geiger-Muller counter was used. Developed originally by Brown and Miller,- his method was adapted to the analysis of carbon-14 marked flotation reagents by Chang, de Bruyn, and Bloecher. nalytica1 method and procedures have been described in detail by Bloecher.' Contact angles were measured by the captive-bubble technique." The mineral specimens were carefully selected to avoid cracks and inclusions of other minerals. All specimens were mounted in plastic and polished to produce a smooth surface. The final polishing and contact-angle measuring

Jan 1, 1955

By O. Mellgren, A. M. Gaudin, P. L. De Bruyn

The adsorption density of ethyl xanthate on pyrite was determined as a function of xanthate concentration. Surface preparation of the mineral appears to have asafunctionsome effect on the subsequent adsorption process, A monolayer of xanthate on the surface is exceeded only in presence of oxygen. The effect of OH- , HS- (and x and CN- S=)and on the amount of xanthate adsorbed was investigated. Competition between OH- and X- (xanthate) ions for specific adsorption sites is indicated over a wide pH range. IN the flotation of sulfide ores, xanthates are most commonly used to prepare the surface of the mineral to be floated so that attachment to air takes place. The quantity of agent required to make the mineral hydrophobic is usually very small, of the order of 0.1 to 0.25 lb per ton of mineral. Details of the mechanism of pyrite collection are for the most part unsettled. Adsorption of collector has long been believed to involve an ion exchange mechanism as demonstrated for galena' and for chalcocite.2 In the work on chal-cocite it was also demonstrated that a film of xanthate radicals unleachable in solvents that dissolve alkali xanthates, copper xanthate, or dixanthogen was formed at the surface of the mineral. The unleachable product increased with increasing addition of xanthate up to a maximum corresponding to an oriented monolayer of xanthate radicals. Pyrite is extremely floatable with xanthate if its surface is fresh.9 ut the floatability decreases rapidly as oxide coatings increase in abundance. Pyrite shows zero contact angle when in contact with ethyl xanthate solution at pH higher than about 10.5;4 at neutrality, a contact angle of 60" is obtained at a reagent concentration of 25 mg per liter. Alkali sulfides and cyanides are pyrite depressants. In this study of pyrite collection the writers have sought to relate measured xanthate adsorption to the method used in preparing pyrite, to the presence or absence of oxygen, to concentration of hydroxyl, hydrosulfide, sulfide, and cyanide ions. The principal experimental tool has been radioanalysis," " using xanthatcx marked with sulfur 35. Experimental Materials Pyrite: Unlike most sulfides, pyrite is a poly-sulfide. The structure given by Bragg7 resembles that of sodium chloride, the iron atoms corresponding to the position of sodium and pairs of sulfur atoms corresponding to the position of chlorine. The edge of the unit cell in pyrite is 5.40 A and in halite 5.63 A. The S-S distance in pyrite is 2.10 A; the Fe-S distance, 3.50 A: and the Fe-Fe distance, 3.82 A. Natural pyrite from Park City, Utah, was used in this investigation. Pyrite 1 was obtained by hand picking pure crystals. Pyrite 2 and Pyrite 3 were obtained from finer textured crystalline material containing inclusions of silicates. The same cleaning technique was utilized for the preparation of Pyrite 2 and Pyrite 3, whereas a different cleaning technique was used for Pyrite 1. Pyrite 1 was prepared as follows: The crystals were ground in a porcelain ball mill and the 200/400 mesh fraction was separated by wet screening with distilled water, followed by washing for 1 hr with deoxygenated distilled water acidified with sulfuric acid to pH 1.5. The acid was removed by rinsing with deoxygenated distilled water on a filter until a pH of 6.0 was reached in the effluent. This filtration was carried out under nitrogen. The sample was then dried in a desiccator under nitrogen. The period of time for which this pyrite sample was in contact with water containing oxygen was about 4 hr. The specific surface as determined by the BET gas adsorption method was 582 cm2 per g. Final material assayed 53.12 pct sulfur and 46.5 pct iron (theoretical, for FeS,: S, 53.45 pct; Fe, 46.55 pct). After crushing, Pyrite 2 and Pyrite 3 were washed with 1 M HCl. rinsed, and fed to a laboratory shakinq table to remove the small amount of silicates. The concentrate obtained was ground in a laboratory steel ball mill. The 200/400 mesh fraction was separated by classification in a Richards hindered settling tube. This fraction was then given a final wash with 0.1 M HCl and deoxygenated water was filtered through the sample. The final effluent showed a conductivity equivalent to that of a solution having a salt concentration of 0.3 ppm. Aqueous hydrogen sulfide solution was then added to the sampln (about 100 ml saturated H,S solution to about 1000 g pyrite under a few hundred milliliters of water) which was stored wet under nitrogen. The sample stored in this manner showed no indication of formation of iron oxides, whereas iron oxides appeared

Jan 1, 1957

By F. F. Aplan, P. H. de Bruyn

The adsorption density of hexyl mercaptan was measured at the gold-solution and the gold-vapor interfaces. This collector is strongly adsorbed at low concentrations, a monomolecular layer being formed at the gold-solution interface at concentrations as low as 2 x 10'6 moles per liter. A maximum contact angle of 83 ± 3° is observed. From a thermodynamic analysis of the experimental data the changes in surface tension at the gold-gas and gold-solution interface are calculated. The data also suggest that the adsorption density of mercaptan at the gold-gas interface exceeds that at the gold-solution interface. In the equilibrium state, a simple flotation system consists of three phases, the solid to be floated, air, and an aqueous solution in stable contact along a line. During the process leading to this final state, a solid-gas interface is created at the expense of a portion of the liquid-gas and solid-liquid interfaces. This change of state is achieved by addition of a collector and, if necessary, suitable modifying agents to the system. By a combined application of the Gibbs Adsorption and the Young Equations, de Bruyn, Overbeek and Schuhmannl were able to show theoretically that the equilibrium distribution of the collector at all three interfaces determines the magnitude of the contact angle. Their analysis led them to conclude that the equilibrium adsorption density of the collector at the solid-gas interface exceeds its density at the solid- liquid interface. This paper succeeded in focussing attention on the neglected role of the solid-gas interface in flotation. In recent years the application of radiotracer, infrared, electrochemical and electro-kinetic techniques to studies of the solid-liquid interface2-5 enhanced our understanding of adsorption processes at this interface. Except for the measurement of contact angles, the solid-gas interface received no attention in fundamental flotation studies. In an attempt to apply the analysis of de Bruyn, Overbeek and Schuhmann to a simple flotation system, an investigation of the adsorption of hexyl mercaptan onto gold was undertaken. Gold was chosen as the solid phase in order to keep the number of dissolved chemical species in the solution phase to a minimum. Hexyl mercaptan (1 - hexanethiol) was selected as collector because its relatively high vapor pressure at room temperature makes it possible to obtain adsorption measurements at the solid-gas interface. This flotation system consists, therefore, of a pure solid phase (gold), an aqueous solution of a weakly dissociated collector (1 -hexanethiol), and a gaseous phase, nitrogen saturated with respect to both water vapor and mercaptan vapor. EXPERIMENTAL MATERIALS AND METHODS Materials: Liquid 1-hexanethiol (C6H13SH) was obtained from Distillation Products Industries and was further purified by double distillation. The purity of the final product was established by boiling point and refractive index measurements. For the adsorption studies from aqueous solution, the radiotracer element, sulfur-35, (half life 87.1 days, 0.169 Mev beta ray) was synthesized into the mercaptan by Tracerlab Inc., Boston, Mass. A close boiling fraction of the synthesized compound was used in the adsorption studies. The specific activity of the radioactive compound was 10 millicuries per gram.

Jan 1, 1963

By S. Usui, I. Iwasaki

The adsorption mechanism of dodecylammonium acetate (DAA) on mercury in potassium fluoride solutions at natural, near neutral pH was investigated. Difler-ential capacity combined with electrocapillary measurements on a dropping mercury electrode were found to provide a sensitive and reliable approach. A shift in the electro capillary maximum (or the point-of-zero-charge) towards positive polarization of the surface due to the adsorption of amine indicated a specific affinity of dodecylammonium ion for mercury surfaces. The amine was shown to adsorb competitively with potassium ion on mercury. Through correlation of the adsorption density of the amine, calculated from the thermodynamic analyses of the electrocapillary curves, and of the diflerential capacity curves, the adsorbed state and the orientation of the amine at the interface were considered. The similarities and the differences in the adsorption behavior of the amine on mercury and on such ionic solids as quartz, silver sulfide, and silver iodide were evaluated. With the promise of flotation providing a cheap and large-scale process for the upgrading of low-grade ores and magnetic concentrates, the iron ore industry has made a sustained search over the years for a flotation reagent of general applicability and high selectivity. Having shelves full of commercial reagents already on hand and anticipating more, both the users and the suppliers are in need of an experimental approach sensitive enough to differentiate the individual characteristics in each group of reagents. Therefore, the adsorption behavior of various flotation reagents on mineral surfaces from aqueous solutions has been a subject of much investigation. The current view of adsorption based on the electrical double-layer theory is formulated on the assumption that certain ions in solution act as potential-determining ions. Their concentrations fix the potential drop across the double layer and their adsorptions govern the surface charge.' Two methods used to study the adsorption

Jan 1, 1971

By L. A. Roe

Magnetic separation of iron ores is one of the fastest-growing segments of the minerals beneficiation industry. The tonnage of taconite ores processed annually by magnetic separation will, in a few years, reach 100 million. Magnetic separation occupies an attractive position in the field of ore beneficiation. It is a simple yet effective method, used for some 150 years and steadily growing more important. This type of beneficiation orginated in 1792, when William Ful-larton was issued a British patent covering the separation of iron ore by magnetic attraction. What is magnetism, and why are some materials capable of being magnetized and others not The study involves many unknowns, and even a partial answer to these questions would be a dissertation in solid state physics and perhaps other fields of science. But the last two decades have revealed basic facts as to why certain materials are magnetic and what happens to them when they are magnetized. Some of the newer studies in solid state physics have developed a theory that can be applied to studies of magnetism. It is claimed that magnetism stems fundamentally from the spin of electrons in atoms that tend to go in pairs, spinning in opposite directions. The atom as a whole can act as a magnet only when there is an imbalance of electronic spin. Whenever an atom has an odd number of electrons, therefore, this imbalance exists. This neutralizing effect explains why a piece of material that contains atomic magnets is not necessarily magnetic. The physicists tell us that iron is composed of many small magnetized regions called domains, which consist individually of millions of atoms. The piece of iron becomes magnetized when an external force lines up these domains in the same direction. Fundamental data developed by physicists working in fields far removed from minerals beneficiation are now available for developing better magnetic separators for ore processing. More Data Needed on Magnetic Properties of Minerals: There is less information on magnetic properties of minerals than there is for certain aspects of magnetic separator design. When the data on magnetic properties is available, it is often directed toward the study of powders for tape recorders and other highly scientific endeavors that are of little use to the beneficiation engineer. W. R. Crane's table of tractive forces, published in 1902, is still a guide in the study of magnetic minerals. Bits of other information regarding electrostatic conductivity, dielectric constant values, and permeability of various minerals have also appeared but are of small practical value in magnetic separation of ore. It is extremely important to obtain pure mineral specimens for making investigations and to record results that may be of use in studies of magnetic processes. Reference to the large volume of data developed by those concerned with analysis and design of permanent magnets soon reveals that these people have extensively evaluated the effect of various impurities on magnetic properties. Much of the science of the ferrite industry is based upon spinel-type structures which are varied by substitution of selected elements or even subtraction of elements, leaving vacant sites in the space lattice. Magnetic separators are used to beneficiate a wide variety of industrial minerals. In this application the relatively large volumes of nonmagnetics are usually the commercial products. The amount of mag-

Jan 1, 1959

By Ellis H. Gates

BENEFICIATION of the manganese oxide ores at Three Kids Mine near Henderson, Nev., has evolved over a period of years. Commercial application of the process is on a secure basis, and an effective working hypothesis has been formulated to help solve the problems encountered in flotation. An outstanding difference between the Manganese Inc. operation and other flotation processes is the necessity for high recovery of slime mineral values. Part of the manganese minerals in the Three Kids ore deposit occurs as primary slime or as minerals that are easily slimed by grinding. High recovery of this slime portion is essential to an economic overall manganese recovery. The aim of much of the research at Manganese Inc. was to recover these slimed and finely ground minerals by flotation. Early Agglomeration Processes: Tunbridge' in 1880, followed by Everson2 in 1886 and Cattermole" in 1904, discovered that under certain pulp conditions precious metals and sulfide minerals could be agglomerated if enough soap or oil were mixed into the pulp slurry. These agglomerated particles, Which under ideal conditions ranged from 1/16 to 1/4 in. diam, were recovered by screening, tabling, and hydraulic classification. Even flotation by air occluded in the agglomkrate particles by vigorous stirring was suggested. Cattermole nearly succeeded in getting his process into commercial operation, but it was finally abandoned, presumably because he could nat compete with the low reagent requirements of the new agitation froth process. Since Cattermole's time Christensen in 1921, Borcherdt4 in 1926, and Chapman and Littleford- in 1934 have attempted to apply the principles of agglomeration. In the light of current research at Manganese Inc. on conditioning of pulp at high energy input levels, it is interesting to note the variety of equipment such as tumbling mills, mixing drums, and shakers described by Borcherdt in his patent to produce the agglomerated particles. Ore Characteristics: Manganese in the Three Kids ore occurs as a 'complex mixture of manganese oxides commonly Known as wad. The manganese minerals have Been identified as psilorflelane, hollandite, coronadite, and pyrolusite with minor amdunts of rhodonite and rhodochrbsite. The ppincipal gangue miherals are quaktz, opal, kaolinite, montmoril-lonite, calcite, gypsum, fcelesitite, and barite. Most of the mangandse ore minerals are either porous and sponge-like in structure or soft clay-like masses composed of fine grained mineral particles approaching the size range of colloids. Consequently the ore minerals from the Three Kids mine have relatively large surface areas and high void content per unit weight. The specific area of various manganese ore samples measured at the California Research Corp. laboratories ranged from 32 to 58 sq m per g. The great surface area and high void content explains in part the unusually high reagent consumption required in the treatment of this ore. Current Milling Practice: At Henderson6 he ore is crushed to —1 in. and ground with rod mills in a closed circuit with spiral rake classifiers and cyclones. Sulfur dioxide solution is added to the pulp as it leaves the grinding circuit, immediately followed by addition of a reagent mixture of soap, oil, and wetting agent in the form of an emulsion. The reagents are initially well mixed into the pulp during their passage through centrifugal pumps to the conditioning equipment. All reagents are added prior to conditioning. The intense conditioning or mechanical stirring of the pulp, in which large amounts of power are consumed, is the principal difference between the flowsheet used at Manganese Inc. and a standard flotation circuit. As much as 38 kw-hr of energy per dry short ton of ore in a pulp containing 18 to 23 pct solids is used for conditioning. After conditioning, the pulp passes to a flotation circuit that consists of one roughing stage, a scav-

Jan 1, 1958

By W. F. Stowasser

downdraft traveling grate process to agglomerate pelletized iron ore concentrates has been successfully demonstrated in a pilot plant at Carrollville, Wis. Work there followed several years of development in the Allis-Chalmers Mfg. Co. laboratories, and the pilot plant phase was carried out in cooperation with Arthur G. McKee & Co., consultants and engineers to the iron and steel industry. End result of the process is conversion of iron ore concentrates into a form which can easily be transported and smelted in the blast furnace. Process Description The first of two process steps incorporates the art of balling and prepares the concentrates for burning. The second step consists of burning the green balls on the grate machine to the hardness required for shipping and handling purposes and for reduction in blast furnaces, see Fig. 1. Facilities are provided at the pilot plant to receive carload quantities of concentrate. The concentrates are loaded into a 50-ton bin direct from railroad cars. Because of the variable moisture content of the concentrates after shipment in an open railroad car it is necessary to repulp and refilter the concentrates to maintain a uniform and proper moisture content for the balling operation. Concentrates are conveyed to slurry tanks, and the slurry, at 50 to 60 pct solids, is pumped to a 4x4-ft drum filter. The filter provides feed of uniform moisture to the plant. Magnetite concentrates are normally filtered to produce a cake containing about 10 pct moisture, a necessary requirement for the following balling operation. The filtered concentrate is conveyed to a rotary bin table feeder which acts as a surge bin for the filter cake and delivers a steady flow of concentrates to the balling drum. It is often desirable to make additions to the concentrates as they are fed to the balling drum. These additives, such as bentonite, increase the strength of the finished green pellet and improve ballability of the concentrate. A vibrating feeder supplies additive to the feed belt, and the additive is mixed with the concentrate in the balling drum. The balling drum, shown in Fig. 3, is 8x3-ft diam. An oscillating cutting bar maintains the lining in the drum by trimming off the buildup of excess concentrate as it forms. The drum is operated in closed circuit with a lx4-ft rod-deck vibrating screen. Undersize pellets or seed pellets from the screen are returned to the balling drum until they grow to the desired size. Size of pellets is controlled by the opening in the screen deck. The formation of pellets in the balling drum is affected by many variables. Some of these are: the size distribution of the feed, the particle shape of the concentrate, the feed rate to the drum, the moisture in the concentrate, the speed of rotation of the drum, the slope of the drum, and the type of trimming obtained with the cutting bar. In this process, attempts are made to control the pellet size within the limits of % to 5/8 in. diam. The screened oversize pellets are conveyed under a coal feeder where sufficient powdered coal is added to the belt to produce desired results in the burning process. The top size of the coal successfully used has been 20 mesh, and anthracite was used in the test program. Fig. 4 illustrates the vibrating screen and the coal feeder. The pellets and free coal are conveyed together to the 5x3-ft diam- reroll drum that rolls the coal onto the surface of the pellets. This drum is also equipped with a cutting bar. The prepared pellets, containing bentonite, water, and surface coal, are elevated to the traveling grate, which consists of a continuous strand of 37 pallets. Each pallet, with a grate bar area 2 ft wide by 1 1/2 ft long, has 14-in. high side plates, Fig. 5. Feeding and distribution of the green balls to the grate is handled by a short conveyor which oscillates back and forth across the 2-ft width of the grate. An adjustable vertical plate located several inches in front of the head pulley of the oscillating conveyor controls the height of the bed and levels the moving bed of pellets. This method of feeding prevents segregation of various size pellets as well as fines and produces a uniform, permeable bed. The pallet train moves under the furnace and across four windboxes, located beneath the pallet frames, see Fig. 2. As the green pellets are deposited on the grate, partial drying of the pellets begins over a 2-ft long updraft windbox. The low temperature air reduces the moisture in the pellets in the lower level of the bed and this operation is essential to prevent sagging of the bed during later stages of the Process. The air used for this drying is recuperated from cooling the pellets on the grate, and supplemental heat, required for starting the Process, is obtained from an auxiliary burner. The pellets are then moved by the grate into the furnace and over an 8-ft windbox, designated as the downdraft waste windbox. Products of combustion are exhausted from this windbox to atmosphere. The furnace, shown in Fig. 6, is constructed with three chambers to provide downdraft drying, preheating, and ignition, respectively, to the pellet bed as it passes through. Overall length of the furnace is 5.57 ft; however, the exterior wall ends may be moved to reduce the length and also adjusted to Obtain the bed height desired, The drying, preheating, and ignition sections of the furnace are supplied with medium temperature

Jan 1, 1956

By W. F. Stowasser

Robert E. Hagen (Oliver Iron Mining Div., U. S. Steel Corp.)—Mr. Stowasser and his associates are to be congratulated on their achievements in developing the design of a pilot agglomerating plant, based on information obtained from experiments made in a laboratory sinter pot, and subsequently constructing and successfully operating this plant. In his Transactions article, May 1955 (vol. 201) Mr. Stowasser stated that the output of his heat treating strand was about 2 Lt per sq ft of grate area per day and that the fuel consumption was 0.7 to 0.8 million Btu per Lt of product. If it is assumed that the burning zone extends from the back of the ignition furnace to the beginning of the recuperation windbox, only about 1/3 of the grate area over the windboxes is utilized for burning pellets, and the actual rate at which partially dried pellets are burned is about 6 Lt per sq ft of grate area per day. It may be interesting to compare the above operating data with that obtained at the Extaca plant, where taconite concentrate is treated on a conventional sin- tering machine using limestone or hydrated lime additives with no recuperation of heat. The entire windbox area is used for burning, and a production rate of 2.5 Lt per sq ft of windbox area per day has been attained at a fuel consumption of 1.8 to 2.0 million Btu per Lt of product, the latter being considerably in excess of that reported by Mr. Stowasser, partly because a circulating load of returns amounting to 28 to 30 pct of the machine feed is used and because no attempt is made to recuperate heat from the waste gases. With the high capital and labor costs prevailing today, it seems that future development of the downdraft grate pelletizing process should be directed toward taking advantage of the high burning rate of predried pellets and increasing capacity, perhaps at the expense of fuel economy, by decreasing the proportion of grate area utilized by ancillary functions. For example, eliminating the cooling zone and using this area for burning would increase the proportion of grate area available for burning from 33 to 50 pct of the total windbox area, and a proportionate increase in capacity would result.

Jan 1, 1956

By H. Rush Spedden, Arvid Thunaes

R. R. Knobler and F. E. Albertson—Following the testwork done by Thunaes and Spedden, a Sullivan deck plant was built for the Colquiri mill. This plant started to operate in April 1945 and continues in successful operation. Since May 1950 the Colquiri mill has operated with a completely revamped flowsheet at a rate of 1000 tons per day. The old Sullivan deck section was retained with this new flowsheet. The "slime plant" in Colquiri consists of one 12-cell Denver No. 18-Sp. Sub-A flotation machine, one 16-ft and one 12-ft hydroseparator, six five-deck Sullivan-frames and six shaking tables for cleaning up the Sullivan deck concentrates, as well as 12 Deister plus three Plat-O tables on which the fine sands, which are not treated on the S-decks, are concentrated. Only —325-mesh fines are treated on the Sullivan decks. The combined hydroseparator overflows are fed to the S-decks. From 1946 to 1949, i.e. with the "old" flowsheet and an average mill feed of 800 tons per day an average of 45 tons per day was treated on four Sullivan rougher frames. The two additional frames were used as cleaners. At times, up to 90 and 120 tons of slimes were treated successfully on this Sullivan deck installation. The average operating data for the S-deck section in Colquiri for the year 1949 were as follows: The tests reported in this paper indicated a tin recovery of 42 pct. The actual plant results for 1949 show a 54 pct tin recovery from the Sullivan decks. The total average quantity of tin produced from the S-deck section in 1949 was 15 tons of tin per month. This corresponds to 3 pct of the total mill recovery. The difference between the 6 pct overall recovery-increase expected after the tests in 1943 and the actual plant results given for 1949 is explained as follows. According to the tests, a total of 170 tons was expected to be routed to the Sullivan decks, but because of certain changes in the flowsheet and mill amplifications,

Jan 1, 1951

By H. Rush Spedden, Arvid Thunaes

R. R. Knobler and F. E. Albertson—Following the testwork done by Thunaes and Spedden, a Sullivan deck plant was built for the Colquiri mill. This plant started to operate in April 1945 and continues in successful operation. Since May 1950 the Colquiri mill has operated with a completely revamped flowsheet at a rate of 1000 tons per day. The old Sullivan deck section was retained with this new flowsheet. The "slime plant" in Colquiri consists of one 12-cell Denver No. 18-Sp. Sub-A flotation machine, one 16-ft and one 12-ft hydroseparator, six five-deck Sullivan-frames and six shaking tables for cleaning up the Sullivan deck concentrates, as well as 12 Deister plus three Plat-O tables on which the fine sands, which are not treated on the S-decks, are concentrated. Only —325-mesh fines are treated on the Sullivan decks. The combined hydroseparator overflows are fed to the S-decks. From 1946 to 1949, i.e. with the "old" flowsheet and an average mill feed of 800 tons per day an average of 45 tons per day was treated on four Sullivan rougher frames. The two additional frames were used as cleaners. At times, up to 90 and 120 tons of slimes were treated successfully on this Sullivan deck installation. The average operating data for the S-deck section in Colquiri for the year 1949 were as follows: The tests reported in this paper indicated a tin recovery of 42 pct. The actual plant results for 1949 show a 54 pct tin recovery from the Sullivan decks. The total average quantity of tin produced from the S-deck section in 1949 was 15 tons of tin per month. This corresponds to 3 pct of the total mill recovery. The difference between the 6 pct overall recovery-increase expected after the tests in 1943 and the actual plant results given for 1949 is explained as follows. According to the tests, a total of 170 tons was expected to be routed to the Sullivan decks, but because of certain changes in the flowsheet and mill amplifications,

Jan 1, 1951

By M. E. Wadsworth, L. H. Raby, A. S. Peck

Infrared spec troscopy was used to study the adsorption of oleate collector on three varieties of hematite. Each of the minerals was found to react with either oleic acid or a solution of sodium oleate to form a mineral cation-collector anion chemisorbed layer at the solid-liquid interface. The chemisorption reaction displaced surface hydroxyls and was found to be pH dependent. The infrared band characteristic of the antisymmetrical C = 0 structural group of chemisorbed oleate appears between 1520 and 1540 cm-'. Evidence is presented which shows that molecular filming of the mineral surfaces with un-dissociated oleic acid precedes chemisorption. Infrared absorbance is correlated with the flotation behavior of the mineral. Adsorption processes are usually classified into two types which are distinguished and character- ized by the nature of the bond formed between the adsorbate and adsorbent. The process in which molecules chemically bond to solid surfaces is termed activated adsorption or chemisorption. If only weak van der Waals forces bind the molecules to the surface then the process is termed physical adsorption. Chemisorption is of primary interest in flotation systems since selectivity may be obtained if a single mineral is rendered air-avid by a specific collector mineral adsorption reaction. In previous studies infrared spectroscopy was used to define the mechanisms involved in the adsorption of oleic acid and sodium oleate on fluorite, barite, and calcite. Infrared techniques were particularly useful since adsorbed monolayers were identified in situ. Further, the infrared method permitted identification of reaction products in the solid, liquid, and vapor phases of the systems. The chemisorption reactions displaced F- from fluorite, SO4 from barite, and CO3 from calcite. This investigation was pursued in an effort to characterize and interpret the adsorption processes for synthetic hematite, compact red hematite, and specular hematite (crystalline hematite). Adsorption tests were performed using either oleic acid or

Jan 1, 1967

By M. E. Wadswort, A. S. Peck

Infrared data disclose that phenacite reacts with oleic acid to form a chemisorbed oleate monolayer on the mineral surface. The absorption band characteristic of the antisymmetrical C = 0 oleate structure appears at a spectral wavelength of 1623 cm-'. Chemisorption also results in the displacement of OH- and silicate from the mineral surface. Infrared absorbance at 1623 cm-1 is correlated with float-ability at different pH for -60-mesh phenacite particles. Phenacite, Be2SiO4, is an ore mineral often associated with quartz, microcline, and chrysoberyl in pegmatites and mica schist. Experimental phenacite beneficiating processes have been confined principally to the flotation of low grade ores occur-ing in several mountain ranges of Utah and Nevada. The U.S. Bureau of Mines ' has recently reported on the separation of phenacite from ore deposits of Mount Wheeler, Nev. Infrared techniques were previously applied by the authors to characterize the role of sodium oleate and oleic acid in the flotation of several non-sulfide minerals.23 A parallel study was projected to the flotation of the orthosilicate mineral phenacite with oleic acid. Infrared spectra provided a 'molecular fingerprint' of the mineral surface and permitted identification of the reaction mechanisms. Infrared data were complemented with flotation and chemical tests. EXPERIMENTAL PROCEDURES The experimental procedures used in this investigation, for which data are presented in graphical or spectral form, are described in chronological test order. Phenacite crystals from Mt. Antero, Colo., were obtained from Ward's Co., Monterey, Calif. The crystals were fragmented in a porcelain mortar to -60 mesh and then pretreated with 0.5 molar HC1 for 15 min to remove iron. Then, the mineral particles were washed free of acid with distilled water and dried. Part of the dried material was ground to a fine powder with a Fisher Grinder using an agate mortar and pestle. Next, the powder was placed in a graduated cylinder and mixed with 500 ml of distilled water. The mineral in suspension was decanted from the settled fraction after 5 min, and the colloidal suspension was used for adsorption tests in which a high specific mineral surface area was required for adsorption and infrared analysis. Conditioning was performed in 50 ml glass centrifuge tubes for both infrared and flotation test determinations. Twenty ml of colloidal suspension was used for the infrared adsorption tests. One and a half g of deslimed -60-mesh HCl pretreated phenacite was added to 20 ml of distilled water for flotation conditioning tests. Six mg of oleic acid was used for each infrared adsorption test, and 0.2 mg of oleic acid was used for the flotation conditioning tests. HCl and NaOH were used for pH modification. The pulps were stirred at a speed of about 1500 rpm for 3 min. Then, the solids were separated out and either dried at 50°C or immediately transferred to a float cell. The pH of the residual liquid was determined with a Beckman Zeromatic pH meter. The flotation procedure is described as follows: 1) A 325-1111 glass micro-float cell was filled with distilled water. 2) Conditioned mineral was placed in the cell and the pulp was aerated through the glass fritted bottom at 7 psi pressure. 3) Floated mineral was skimmed from the cell with a glass slide until flotation ceased. (The end point was reached in all tests in less than 2 min.) 4) The flotation products were dried, weighed, and the recovery was calculated. Samples for infrared analysis were made into mulls using either oleic acid or series 13-21 Halocarbon oil obtained from Halocarbon Products Corp., Hacken-sack, N.J. The mulls were placed between two sodium chloride windows. A characteristic phenacite infrared band at 1868 cm-' was used as an internal standard for quantitative determinations in which absorbance at this position was quantified by the baseline-tangent method4 and related to absorbance at 1623 cm-'. The ratio obtained by dividing absorbance at 1623 cm-' by absorbance at 1868 cm-' was defined as an absorbance quotient for use in graphical presentation.

Jan 1, 1968

By C. C. Harris, A. Jowett, S. K. Ghosh

An equation derived from first-order kinetics and accounting for return from froth to pulp has correlated continuous flotation data. The concentration of floatable material in the pulp can be altered either by changing the feed concentration or the feed rate. The latter does not affect the flotation rate constant, the froth to pulp return constant, and the concentration of non-floatable material in both the pulp and concentrate. Both the return constant and the concentration of non-floatable material in the pulp are directly proportional to the feed concentration, while the concentration of non-floatable material in the concentrate is related to the feed concentration. The investigation of the froth flotation process by continuous test methods, previously used by Brown and smith,1 Jowett and Safvi2 and Jowett and West,3 is being continued. Recent tests, primarily concerned with flotation cell design, have yielded kinetic data suitable for testing an equation proposed by Arbiter and Harris4 which postulates that a flotation process is defined by two rate constants: 1) the rate constant for mass transfer from pulp to froth. Previous workers have regarded this as the flotation rate constant. 2) the rate constant for mass transfer from froth to pulp, which has previously been ignored. THEORY Under continuous flow conditions at the steady state in Fig. 1 the equation developed4 is Symbols are defined in Table I. The air-liquid ratio terms4 have been omitted, since they are substantially constant for a given set of conditions. Also, for a system operating at the steady state Vf and V, remain constant and Eq. 1 can be written: Cp/Cc=b'/a,+Qc/a' [2]

Jan 1, 1963

By R. S. Olson

An analysis of the wash thickener-two stage filtration circuit was undertaken to quantitatively describe the circuit performance. On the basis of information developed in this study, the factors of major importance in reducing soluble loss are: filter wash, wash zone size, filter capacity, filter feed pulp dilution, blow back, filter cloth, water to repulp, water to primary wash, water to feed pulp and thickener underflow. The wash thickener-two stage filtration circuit has been used in many hydrometallurgical plants to separate solute from leach solids. As many as 20 to 30 plant operating variables determine the performance of the wash circuit and hence the soluble loss. The complex relationships of these variables, with each other and with soluble loss, make the evaluation of their effect on mill performance difficult. An analysis of this type of circuit was undertaken to quantitatively describe the circuit performance. THE CIRCUIT The diagram in Fig. 1 represents the operation of the wash thickener-two stage filter circuit. This circuit provides for counter current, cross current or for a combination of countercurrent-cross current operation. The feed pulp stream, J, is intended to include any solution or water, other than primary and secondary filtrate, which enters the wash thickener. Except for filter washing, the operations in the circuit are simple mixing operations which can be described by material balance. The concentration of solute in the filtrate and cake solution after application of wash liquor cannot be described by simple material balance. The displacement washing equation, derived by Rhodes1 and extended by Choundhury and Dahlstrom,2 appears to best describe this case of miscible displacement in porous media. In a useful form, it is

Jan 1, 1963

By G. H. Wilson

INTRODUCED in 1946 to serve a need in power-plant operation, closed-circuit TV has been used by well over 200 organizations in approximately 25 different industries. Known as industrial television, or simply ITV, it can be described as a private system wherein the television signal is restricted in distribution, usually by confinement within coaxial cable that directly connects the TV camera to one or several monitors, Figs. 1, 2. The picture is continuous and transmission is instantaneous, permitting an observer to see an operation that may be too distant, too inaccessible, or too dangerous to be viewed directly. Destructive testing or the machining of high explosives can now be conducted hundreds of feet away by personnel who still have close control through the eyes of the TV camera. It is also possible for one man to control operations formerly requiring the co-ordinated efforts of several workers. For example, at a large midwestern cement plant conveyance of limestone from primary crusher to raw mill and loading into five storage bins once necessitated the work of two men, one having little to do but prevent spilling of material by manually moving the tripper on the belt conveyor as occasion required. TV cameras mounted on the tripper now provide bin level indication to the conveyor operator at the crusher position so he is able to control the entire loading operation remotely, Fig. 3. By means of a switch, the picture from either camera is alternately available on a single viewer, or monitor, Fig. 4. Each camera is mounted on the tripper by means of a simple adjustable support and looks down into the bin, which is identified by the number of cross members on the vertical rod. Each associated power unit is located on a platform above the camera, Fig. 5. This centralized control by means of TV often has produced superior results, and in many instances saving in operating costs has been sufficient to write off equipment costs within six months to a year. Where a key portion of a process may be enclosed or otherwise inaccessible, TV again reduces the likelihood of mistakes and permits closer control by making available to the operator valuable information he might otherwise never possess. An example of this can be found at a strip mine where the coal seam lies 50 ft or more below the overburden, which is removed by a large wheel shovel. From his centrally located position the shove1 operator was unable to judge accurately to what extent the wheel buckets engaged the earth. His chief indication of efficiency was the amount of overburden on the belt conveyor as it passed his control point 75 ft from the wheel. Now, two television cameras mounted on the tip of the boom permit the operator to view the wheel from each side and provide him with a close-up view of the buckets so that he can take immediate and continuous advantage of their capacity, quickly compensating for ground irregularities and avoiding obstructions, Fig. 6. While the word television conjures up visions of highly complex and intricate apparatus such as that employed in modern TV studios and transmitting stations, the term industrial television should indicate compact, straightforward equipment. Most present-day ITV systems contain fewer than 25 tubes including camera and picture tubes. The average home television receiver alone requires at least that many tubes. Equipment like that illustrated in Fig. 1 contains only 17 tubes, of which 3 are in the camera. It can operate continuously and dependably, without protection, in any temperature from 0" to 150°F. It consumes less current than a toaster and weighs under 140 lb. Camera and monitor may be separated by 1500 to 2000 ft and by greater distance with additional amplification. This equipment is designed to withstand vibrations up to 21/16 in. and will operate successfully under more severe conditions of vibration and heat when suitable enclosures are provided. Any number of cameras may be switched to a single monitor, and any number of monitors, within reason, used simultaneously. Two types of applications in the mining industry have already been described. A third under serious consideration by several organizations will make use of ITV for remote observation of conveyor transfer points at copper concentrating plants so that evidence of belt breakdown and plugging of transfer chutes can be spotted immediately and costly overflow of material avoided. A television camera will soon be installed to view a trough conveyor near the exit of an iron-ore crusher to indicate clogging of the crusher as evidenced by reduction or absence of material on the

Jan 1, 1955

By J. E. Lawver, G. L. Samsel

The success of many mineral dressing processes, including froth flotation and electrical concentration, depends largely on knowledge of physical and chemical structures of the mineral surfaces involved. As a general rule solids have surface layers, usually invisible by optical tests, that differ from the substratum. To the mineral engineer, therefore, a knowledge of the surface structures of minerals is of paramount importance. During the past decade one of the most powerful tools in the study of froth flotation mechanisms has been the use of radioactive tracers, but this technique usually cannot give definite information regarding the chemical changes that may or may not have occurred at the surface. The electron microscope and electron diffraction camera can be particularly useful instruments in surface studies.. An election microscope permits much closer examination of surfaces than can be obtained with a petrographic microscope. In certain cases, it is possible to identify trace quantities formed by chemical reaction between flotation agents and mineral surfaces by the use of a single-crystal, reflection electron diffraction camera. This article describes several instances in which these instruments have been valuable guides in mineral dressing research at International Minerals & Chemical Corp. One of the first applications of these techniques employed by International Minerals was in conjunction with the study of electrical concentration of potash ore. The first reasonably successful separation of potash ore was made by subjecting a sample of the ore to a methanol wash. Subsequent tests using tagged 6C14 methanol showed that only a minute quantity of radioactivity was detectable after the methanol-washed sample had been dried and heated to about 300°F. It was concluded that although some methanol had been held to the surface by adsorption, this could not account for the improved electrification because there was no evidence of methanol selectivity with respect to NaCl or KCl. Consequently there must have been some other change in the surface. Carbon replicas* of the mineral grains were made before and after the methanol wash. The replicas were separated from the minerals by dissolving in water. This extraction replica technique is particularly attractive because the specimen can first be used with the electron microscope to observe the general structure of the surface and can be re-used as a specimen for electron-diffraction studies to identify any solvent insoluble material present on the mineral surface." Fig. 1 shows the general

Jan 1, 1960

By H. H. Dreissen, F. J. Fontein

The operating principle of the classifying cyclone has been described often but some special aspects of the cyclone receive further clarification here. In addition, several uses of the classifiers are summarized and made clear by means of practical examples. In coal and ore washeries, the washing cyclone is widely used for the separation by specific gravity of sizes up to about 12 mm. This application has lately been extended to the separation by specific gravity of particles up to about 50 mm. This use makes special demands on the construction and wear resistance of the cyclone. The sieve bend, a development of the Dutch State Mines which is less well known than the hydrocy-clone, is dealt with at some length. The sieve bend is an apparatus designed for wet screening. Attention is given to the variables influencing the performance of the sieve bend. Hydrocyclones are now so widely applied that it would be difficult to find an industry not, directly or indirectly, using them or knowing how to use them since publications on this subject abound.1-3,5,9-11,13-15 However, because of the large number of variables influencing the operation of classifying cyclones, it is not entirely possible to calculate the results of this type of cyclone. Therefore, a number of lesser known variables will be discussed here along with some special applications of the classifying cyclone. FACTORS INFLUENCING CYCLONE CLASSIFICATION Shape of Particles: The shape of particles may cause a much coarser classification than the one expected, considering the sieve analysis and the cyclone dimensions chosen. This was clearly shown by feeding a mixture of spheres and disks in water into a cyclone. The spheres were 0.36 mm diam and the disks, 3 mm diam and 0.03 mm thick. These dimensions were chosen in order that the disks and spheres might have the same rates of fall under gravity. Both spheres and disks had a specific gravity of 1.05. The results obtained with these particles in a cyclone are summarized in Table I. Test No. 2 shows that the catch of spheres was

Jan 1, 1963

By A. D. Rovig, D. W. McGlashan, Donald M. Podobnik

Crystal-chemical and stntctural properties of sulfide minerals are considered. The information gained is to be used to interpret (I ) freshly broken mineral surfaces, (2) modifications of the mineral surfaces, and (3) reactions at the mineral surfaces. From these basic disciplines, concepts with regard to the changes that surfaces undergo, reactions that might take place, the geometry of the interface, the state of different atoms and ions in the interface, and other physical and chemical properties of an interface must be developed, weighed and applied. The authors first deal with these conceptual considerations from which hypotheses are set forth to describe the environ men tal-interfacial relationships for several sulfide minerals. Qualitative and quantitative explanation of par-ticulate solid separations are unknown entities because of the lack of adequate models and mathematical relationships to explain the activity occurring between the solid and liquid phases. It is a transitional region in which it is difficult to ascertain the mechanisms of adsorption of ions, molecules, etc., on mineral surfaces, as well as other secondary reactions which occur in interfacial regions. Thus, in this paper the authors deal with conceptual considerations from which hypotheses are set forth to describe the environmental-interfacial relationships for sulfide minerals. GENERAL CONSIDERATIONS Interfacial Reactions:Interfacial reactions are the cruxes of flotation schemes as well as other processes such as thickening, filtration and hydrometallurgy. However, as noted by Klassen and Mokrousov: 1 "The problems concerning the surfaces of natural minerals, the laws governing simultaneous adsorption from aqueous solution on these surfaces of a whole series of reagents, the laws of the surface reactions and the properties of water layers separating the minerals, are all known to a first approximation only." An investigator has the privilege of postulating methods of solid-liquid interfacial reactions. REACTIONS WITH WATER - Water consists of hydronium (H3 O 4) and hydroxyl (OH-) ions in the ionized state. That this is so forms the basis for the postulated reaction of the hydrated hydrogen ion with net-negative mineral surfaces as depicted in Fig. 1. In this case water is bonded to mineral surfaces through hydrogen-bridge-type bonds - possibly hydrogen bonds. Although bonding of the van der Waal type may be responsible for this reaction, it is most likely that stronger bonds are involved. Once firmly bonded to the surface, the water layer is known to be quite tenacious. It is further speculated that a shear plane exists at some distance (see Fig. 1) away from the mineral surface. Exact location of this plane is not known, but in all probability it will be positioned across a weak bond of the hydrogen-bond type where the surface-attached water is coordinated to the original hydrated hydrogen ion. REACTION WITH METAL IONS - Klassen and Mokrousov ' state: "The presence of an ion in water leads to an immediate formation around that ion of a highly condensed atmosphere of water dipoles and thus to hydration of the ion." The fact is known that multivalent cations are strongly hydrated, usually by six or eight molecules of water, and that anions are not so strongly hydrated. Conceding the fact that thermodynamics, concentration, pH, and physical considerations are of utmost importance in truly explaining a mechanism of metal ions reaction with a hydrated mineral surface, it does seem logical that the mechanism illustrated in Fig. 2 is feasible. In this reaction, the metal ion (M) is coordinated in one dimension - to the mineral-surface hydration layer. Note also that explanation of this reaction requires that the shear plane move to a less stable bond configuration; that is, the shear plane has moved to a position between the metal ion and the other coordinated water molecules which are more free to dissociate. Reactions as depicted in Fig. 2 should cause the formation of an apparent mineral surface which is net-positive. Immediately, it must be noted that measurements of apparent-mineral surfaces serve - within limits - to indicate a degree of ion-surface reaction capability. The major limiting factor he re is one related

Jan 1, 1970