Search Documents

By R. Adair, W. R. Hudspeth, W. T. McDaniel

D. C. Ralston (U. S. Bureau of Mines, Washington, D. C.)—Flake mica can be beneficiated by a wider variety of methods than almost any known mineral. However, most of these methods are not recorded. It is therefore a pleasure to find a written record of another application of a new method of beneficiation. The fact that the Humphries spiral gives a concentrate containing the mica flake mixed with the slime and small grit has forced a further separation by screening, in which the finest of the flake will pass through. Fine flake has its uses and if mixed with slimes or clay is recoverable reliably only by flotation. This loss must be charged against the spiral. On the other hand, the new muscovite mica paper recently brought out by General Electric Co., can be made only with grit free flake larger than 50 mesh. It is of interest to learn from the authors whether the washing of the flake on a 50 mesh screen can take the grit content below 1 pct, to meet this new demand. Must another degritting process be used on the flake, like electrostatic treatment of the dried material? H. D. Snedden (The Humphreys Investment Co., Denver)—When recovering mica in the spiral, gangue particles coarser than 16 mesh can be rejected more readily when operating at a high pulp density (35 pct solids) or a low volume rate (—15 gpm). A launder screen as used by Lehigh Coal Co. has proved very satisfactory to partially dewater the mica concentrate and to reject any gangue slimes it may contain. Under certain conditions mica cleaning in the spiral can be improved by reagentizing the spiral feed, the object being to insure wetting of the gangue minerals and to agglomerate or prevent wetting of the mica particles. R. B. Adair (authors' reply)—The grit content of the mica recovered on Humphreys Spirals varies with the fineness of the launder screen used to clean the mica product. Normal practice has been the use of 80 mesh screen, which will produce a mica product of acceptable grit content for most purposes. By using a 50 mesh screen, and increasing the screen area per ton of feed, it is felt by the authors that a mica of 99 pct plus purity could be obtained. This statement would hold only in the case of mica feed which was well de-laminated, and free from "clay balls," (semikaclinized feldspar), which tends to follow the mica through the process.

Jan 1, 1952

By S. A. Falconer

The benefication of non-sulfide or non-metallic minerals by froth flotation has been practiced commercially for at least 30 years. In the pioneer stages of development of this flotation art, most of the promoters investigated were fatty acids or soaps that had been found to float sulfide minerals. When commercial application of froth flotation started to assume importance in the late 1920' s and 1930's, a great deal of fundamental research work was done in the laboratory (11-14, 19, 22, 23, 26, 29, 32). Among other subjects, this work included studies of the relative effectiveness of the different fatty acids and their salts on the flotability of various non-sulfide and non-metallic minerals. The successful present-day use of fatty acid and petroleum sulfonate type promoters results from better understanding of the principles of non-sulfide flotation plus the developnent of effective selectivity modifying agents. Many investigators have contributed to a greater appreciation of the numerous interrelated factors involved in fatty acid and soap flotation of non-sulfide minerals. Of these, mention should be made of recent fundamental studies by Tagart and Arbiter (31); Wolstenholme and Schulman (35); Schulman and Smith (28); Wark and his co-workers(3,4) Du FIietz(l5); and J. Leja(24). According to J. Rogers, K. L. Sutherland and E. E. and I. W. Wark(27), "the basic requirements for a 'collector' in flotation are that it shall form a film over the surface of the mineral to be floated and that this film should be oriented so that hydrocarbon (non-polar) groups form the effective surface." When modified in that way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince (33)that such a film can be produced only if the collector compound contains an active (polar) group to be attracted to the mineral surface, as well as the non-polar group. The commonly used anionic-type promoters for non-sulfide, non-metallic and metallic oxide ores include: 1. Fatty acids, and their soaps and emulsions. 2. Fatty acids residues — "pitches" and "foots." 3. Sulfonated and sulfated fatty acids and so-called "petroleum sulfonates." 4. Paraffin chain salts — sulfonated and sulfated higher alcohols. 5. Cyclic organic acids or salts, such as naph-thenic acid and naphthenates. Certain fatty acids are more effective than others as promoters for particular minerals under certain specified conditions. Some of the more costly fatty acids or collectors of the paraffin chain salt type may give improved selectivity in some instances and are being used commercially in a limited number of operations. Local availability may dictate the choice of the fatty acid used — for example, the use of palmoil fatty acid for flotation of copper carbonate ores in the Belgian Congo. Coconut oil fatty acids have also found limited use.

Jan 1, 1961

By Jack White

MUFULIRA Copper Mines, Limited, conducted tests on the concentrator in 1942 to determine which type of ball mill, that is, Conical Trunnion overflow or Cylindrical Grate discharge, produced the greater quantity of finished product at the lowest cost. All the data which follows applies to Mufulira ore and to the particular degree of grinding produced with the classifiers installed at Mufulira concentrator. JACK WHITE, Member AIME, is Concentrator Superzntendent, Mufulira Copper Mines, Ltd., Mufulira, Nortltern Rhodesia. Sun Francisco Meeting, February 1949. TP 2729 B. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Feb. 28, 1949. Test Procedure: The test was carried out using ball mills No. 1 to 9 (conical trunnion overflow) as the standard with which to compare No. 10 (cylindrical grate discharge mill). The conical trunnion overflow ball mills are 10 ft diam by 72 in., and the cylindrical grate discharge mill is a No. 99. Each mill runs in closed circuit with a Dorr type DSFX classifier 8 ft wide by 30 ft long. The feed is considered as being identical to all ten units. The figures for the test were derived as follows. Dry Tons Milled: For No. 10 unit (cylindrical grate discharge mill) this figure was taken from the ball mill weightometer, which was corrected for error, and then for moisture content. The weightorneter was checked twice a week during the test, and the error did not exceed 3 pct at any time. The moisture was obtained from a 24 hr moisture sample taken by the ball mill operator hourly, and placed in a closed bucket. The sample was cut where the conveyor drops the feed into the ball mill chute. The Mill Sampling Department made a daily moisture determination on this sample. To obtain the dry tons on units No. 1 to 9 the No. 10 figure was deducted from the month's dry tons milled figure, which, in turn, was taken from the crusher weightometer tons corrected for weightometer error and moisture. All tons reported in this test are short tons of 2000 lb. Ball Mill Hours: This was taken daily from the Shift Boss reports giving actual running hours for each unit. Screen Analyses: Coarse Heads (Ball Mill Feed): The monthly composite coarse heads screen analysis, done by the Mill Sampling Department, was used for the minus 200 mesh in the feed to the mills. F. X. Classifier Overflow: The ball mill operators took an hourly 24 hr sample of the overflows of units No. 1 to 9. This was a hand sample, but cut with a special cutter, and is believed to be very reliable. On No. 10 unit, an hourly 24 hr sample, and an hourly shift sample were cut in the same way. These five samples were split, filtered, and dried by the Research Department and were then wet screened on a 200 mesh screen. The average of the three shifts samples on No. 10 unit had to check the 24 hr sample within 1.5 pct to be acceptable. A weighted composite was cut each day from both 24 hr samples, and at the end of each month it was screened as follows: Wet screened through 325 mesh, the plus 325 then screened on a rotap for 15 min through 65, 100, 150, 200, and 325. This was done in duplicate. All splitting, drying, and screening of samples was done by one of the Mill Research staff, to insure accuracy. F. X. Classifier Overflow Densities: These were taken from the Shift Boss reports. Densities were taken by the ball mill operator every hour. Circulating Loads: These were taken a number of times during the test both by direct method (weighing a measured portion of classifier rake sand, and deducting moisture) and by calculation using the formula:

Jan 1, 1951

By Jack White

MUFULIRA Copper Mines, Limited, conducted tests on the concentrator in 1942 to determine which type of ball mill, that is, Conical Trunnion overflow or Cylindrical Grate discharge, produced the greater quantity of finished product at the lowest cost. All the data which follows applies to Mufulira ore and to the particular degree of grinding produced with the classifiers installed at Mufulira concentrator. JACK WHITE, Member AIME, is Concentrator Superzntendent, Mufulira Copper Mines, Ltd., Mufulira, Nortltern Rhodesia. Sun Francisco Meeting, February 1949. TP 2729 B. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Feb. 28, 1949. Test Procedure: The test was carried out using ball mills No. 1 to 9 (conical trunnion overflow) as the standard with which to compare No. 10 (cylindrical grate discharge mill). The conical trunnion overflow ball mills are 10 ft diam by 72 in., and the cylindrical grate discharge mill is a No. 99. Each mill runs in closed circuit with a Dorr type DSFX classifier 8 ft wide by 30 ft long. The feed is considered as being identical to all ten units. The figures for the test were derived as follows. Dry Tons Milled: For No. 10 unit (cylindrical grate discharge mill) this figure was taken from the ball mill weightometer, which was corrected for error, and then for moisture content. The weightorneter was checked twice a week during the test, and the error did not exceed 3 pct at any time. The moisture was obtained from a 24 hr moisture sample taken by the ball mill operator hourly, and placed in a closed bucket. The sample was cut where the conveyor drops the feed into the ball mill chute. The Mill Sampling Department made a daily moisture determination on this sample. To obtain the dry tons on units No. 1 to 9 the No. 10 figure was deducted from the month's dry tons milled figure, which, in turn, was taken from the crusher weightometer tons corrected for weightometer error and moisture. All tons reported in this test are short tons of 2000 lb. Ball Mill Hours: This was taken daily from the Shift Boss reports giving actual running hours for each unit. Screen Analyses: Coarse Heads (Ball Mill Feed): The monthly composite coarse heads screen analysis, done by the Mill Sampling Department, was used for the minus 200 mesh in the feed to the mills. F. X. Classifier Overflow: The ball mill operators took an hourly 24 hr sample of the overflows of units No. 1 to 9. This was a hand sample, but cut with a special cutter, and is believed to be very reliable. On No. 10 unit, an hourly 24 hr sample, and an hourly shift sample were cut in the same way. These five samples were split, filtered, and dried by the Research Department and were then wet screened on a 200 mesh screen. The average of the three shifts samples on No. 10 unit had to check the 24 hr sample within 1.5 pct to be acceptable. A weighted composite was cut each day from both 24 hr samples, and at the end of each month it was screened as follows: Wet screened through 325 mesh, the plus 325 then screened on a rotap for 15 min through 65, 100, 150, 200, and 325. This was done in duplicate. All splitting, drying, and screening of samples was done by one of the Mill Research staff, to insure accuracy. F. X. Classifier Overflow Densities: These were taken from the Shift Boss reports. Densities were taken by the ball mill operator every hour. Circulating Loads: These were taken a number of times during the test both by direct method (weighing a measured portion of classifier rake sand, and deducting moisture) and by calculation using the formula:

Jan 1, 1951

By Jack White

W. I. Garms-—The authors state that when they added 11 tons of balls to the 45 pct volume ball load, the power needle did not budge. The question arises as to whether any increase in capacity accompanied the 11-ton addition. It is hardly conceivable that all of the balls making up the l l-ton addition were sterile. However, as the work done in the ball mill is not by kilo-watthours per se or balls per se but by kilowatthour-balls, it is possible that the kilowatthourballs in the mill before the ll-ton addition had a different amperage, voltage or robustage than those in the mill after the addition and that the overall outcome was that equal work was done before and after the addition. The authors can keep the efficiency that they got with the 45 pct volume 1-in. ball charge and get additional capacity by putting more kilowatthourballs to work in the form of the addition of 11 tons of 2-in. balls to the present ball charge, and subsequent makeup additions by weight of 20 pct 2-in. balls and 80 pct 1-in. balls. J. F. Myers (authors' reply)-—Mr. Garms points his finger at the 11 tons of "sterile" balls added to the Tri-cone mill. A fact so interesting to us that we felt it should be reported. Clearly, ball slippage at the existing mill speed prevented any further transfer of power from the shell to the ball mass. We agree that the kilowatthourballs would increase, were we charging rough 2-in. balls as suggested by Mr. Garms. The assumption is, of course, that we would get a corresponding increase in work done. Our reported data (CIME meeting, Vancouver, 1946) shows a gain of work accomplished of 7.6 pct as we decreased the ball size from 2 in. to 1% in. and a further gain of work accomplished of 2.1 pct when we went from 1 % in. to 1 in. The small ball results reported by H. R. Banks at Chapman Camp are also very convincing. In the case of 2-in. balls they would take the conventional ball path and start cascading. They would thus destroy the classifying pool over the "foot" of the

Jan 1, 1951

By Jack White

W. I. Garms-—The authors state that when they added 11 tons of balls to the 45 pct volume ball load, the power needle did not budge. The question arises as to whether any increase in capacity accompanied the 11-ton addition. It is hardly conceivable that all of the balls making up the l l-ton addition were sterile. However, as the work done in the ball mill is not by kilo-watthours per se or balls per se but by kilowatthour-balls, it is possible that the kilowatthourballs in the mill before the ll-ton addition had a different amperage, voltage or robustage than those in the mill after the addition and that the overall outcome was that equal work was done before and after the addition. The authors can keep the efficiency that they got with the 45 pct volume 1-in. ball charge and get additional capacity by putting more kilowatthourballs to work in the form of the addition of 11 tons of 2-in. balls to the present ball charge, and subsequent makeup additions by weight of 20 pct 2-in. balls and 80 pct 1-in. balls. J. F. Myers (authors' reply)-—Mr. Garms points his finger at the 11 tons of "sterile" balls added to the Tri-cone mill. A fact so interesting to us that we felt it should be reported. Clearly, ball slippage at the existing mill speed prevented any further transfer of power from the shell to the ball mass. We agree that the kilowatthourballs would increase, were we charging rough 2-in. balls as suggested by Mr. Garms. The assumption is, of course, that we would get a corresponding increase in work done. Our reported data (CIME meeting, Vancouver, 1946) shows a gain of work accomplished of 7.6 pct as we decreased the ball size from 2 in. to 1% in. and a further gain of work accomplished of 2.1 pct when we went from 1 % in. to 1 in. The small ball results reported by H. R. Banks at Chapman Camp are also very convincing. In the case of 2-in. balls they would take the conventional ball path and start cascading. They would thus destroy the classifying pool over the "foot" of the

Jan 1, 1951

By P. Somasundaran, D. W. Fuerstenau

The length of the collector is found to influence the flotation of the mineral even at incipient conditions, which are below the concentration at which interaction at the solid-liquid interface begins to take place to form hemi-micelles. To study this dependence, concentration for incipient flotation of quartz was determined as a function of pH with collectors of various chain lengths. The observed effect of chain length on flotation is ascribed to that of collector adsorbed on the bubble surface. In previous studies, it was shown that at low concentrations the alkyl collector ions adsorb at the solid-liquid interface as individuals.''2 At higher concentrations, the collector ions adsorbed at the solid-liquid interface associate with each other to form two-dimensional aggregates called hemi-micelles. Above the hemi-micelle concentration, the length of the hydrocarbon chain is extremely important since the hydrocarbons are in effect removed from water during the association, making the energetic conditions more favorable for adsorption at the interface. Because of this enhanced adsorption, one observes a very rapid increase in flotation associated with the hemi-micelle formation at the solid-liquid interface. However, a dependence of flotation on the chain length at concentrations below that required for hemi-micelle association was also observed,' and this cannot be explained by the above mechanism which postulated hydrocarbon chain interactions only at the solid-liquid interface. This prompted an investigation into other possible reactions of the hydrocarbon chains and an examination of the conditions at the bubble surface involved in the flotation system and how these observations might explain the reactions at the solid-gas interface which cause the particle-bubble attachment required for flotation. To obtain more information on chain length effects, flotation, under incipient conditions, was tested by vacuum flotation techniques. The collector-concen-tration-pH relationships for flotation of quartz with alkyl ammonium acetate collectors was delineated by observing the pH at which quartz particles begin to float to the liquid surface. By investigating flotation as a function of pH, it was also possible to study the effect of neutral molecules on incipient flotation conditions, since the aminium ions hydrolyze to amine molecules at higher pH values. EXPERIMENTAL WORK Brazilian quartz specimens were crushed and sized, and the 270 x 400 mesh fraction was used for flotation studies. The samples were leached with concentrated hydrochloric acid until no coloration of the acid occurred. The leached material was washed free of chloride ions and stored in distilled water. The vacuum flotation technique developed by Schuhmann and prakash3 was used to determine the critical pH-concentration curves. This method, which can be used to delineate conditions for incipient flotation, is fairly simple and rapid. About 0.5 gm of 270 x 400 mesh quartz was placed in a 100 ml graduated cylinder which was then filled to the 100 ml mark with the collector solution made from high-purity alkyl ammonium acetate salts. The water used for the test was conductivity water saturated with air that had been passed through a cleansing train consisting of Drierite, Ascarite, a water wash bottle, and a trap. After the pH was adjusted, the cylinder was then conditioned for thirty minutes. In the tests where an acid pH was desired, sufficient acid was added before the collector solution to avoid any effect due to slow desorption of collector from the quartz surface. After conditioning, vacuum was applied to the system and the flotation or nonflotation of the quartz was noted. The pH at which the quartz particles began to float to the liquid-gas interface was taken as the critical PH. Critical pH curves were thus determined for different concentrations of the various collectors. Hallimond tube flotation data were taken from the authors' previous publication1 for correlation with that from the vacuum flotation. RESULTS AND DISCUSSION The results of vacuum flotation studies for determining critical pH-concentration curves, i.e., curves which delineate conditions for incipient flotation, are shown in Fig. I. In generaI, all the curves exhibit an upper and lower pH limit between which flotation will

Jan 1, 1969

By R. W. Smith, R. W. M. Lai

Although several recent papers have shown that equilibrium contact angle in dodecylamine solution-quartz systems can often be directly correlated with flotation behavior, it appears that under conditions of relatively high amine strength and pH such a correlation can't be made. Under these conditions, when there are precipitated amine dipoles present, it appears that a dynamic contact angle formed immediately after introduction of fresh gas bubbles into the system is also of importance. The dynamic angle decreases in magnitude as a function of time. Apparently the decrease is the result of changes in interfacial tensions (liquid-gas and solid-gas) as a function of time. Dynamic angles of the type described can't be observed in trimethyldodecylammonium chloride solution-quartz systems. Several recent papers1-3 have shown quite conclusively that contact angle data can often be correlated directly with flotation behavior in cationic surfactant solution-quartz systems. At the same time, Iwasaki, Cooke, and Colombo4 have shown data for a dodecylammonium chloride solution-goethite system where, in the vicinity of pH 12 and a collector concentration of 10" M, 100% flotation occurs when equilibrium contact angle appears to be zero. A clue to this discrepancy can be found in the work by smith2 who reported the occurrence of dynamic, time dependent, contact angles in a quartz-dodecyl-amine solution system at relatively high pH values and at surfactant concentrations greater than or equal to 10-4 M. It was found that under these conditions, if a fresh bubble was brought into contact with a properly conditioned and polished quartz surface, a large angle was obtained. The large angle, however, instantly started to diminish in magnitude, sometimes to a smaller stable angle and sometimes to its complete disappearance. Also, if the bubble was preconditioned for some minutes (or sometimes even seconds) in the same amine solution, the smaller or sometimes zero stable angle was obtained when the bubble was brought in contact with the quartz surface. One is immediately led to the thought that perhaps it is these dynamic angles when they exist, not stable angles, that are of primary importance in flotation. The present investigation attempts to further study the relationship between contact angle and flotation

Jan 1, 1967

By H. J. Modi, P. L. De Bruyn

IN recent years interest has been aroused in flotation rate studies both from a technical and a more practical aspect. With increasing fineness of grind becoming a necessity in treatment of low grade ores, difference:; in flotation rates of various size ranges will assume importance in the evaluation of overall recovery results. Theoretical analysis of flotation kinetics was initiated by Schuhmann,' who sought to define flotation rate of a given mineral and specified size range in terms of certain physical variables of the flotation system. Using as a basis for his analysis the bubble-particle encounter hypothesis previously advanced by Gaudin,' Schuhmann writes for the rate of flotation (R,.) of particles of average size x, Rx = PcPa(x) V F. [1] In this relation Pc and Pa represent, respectively, the probability of collision between particle and gas bubble in a given time interval and the probability of adhesion of particle to the bubble after collision. Rigorously speaking, the term PC does not have the significance of a probability factor, since it depends on the time interval and therefore can be numerically greater than unity. The term c(x) expresses the concentration of particles of an average size x in the flotation cell in weight per unit volume of pulp, and V denotes the total volume of pulp in the cell. The product, P,c(x)V, defines the frequency of particle-bubble collisl.on, and when it is multiplied by P,, the number of collisions per unit time resulting in successful adherence is obtained. The factor, F, measures the froth stability and is introduced because after fruitful bubble-particle contact some particles may still riot reach the froth launder. Coalescence of bubbles in the froth column or too short a bubble life could account for this effect. Schuhmann also introduced the concept of "specific flotation rate" (Q) to allow for the relative abundance of different mineral species in the flotation pulp. The specific flotation rate, having the dimension of reciprocal time, is defined as Eq. 2: Qx =Rx/c(x)v [2] and it also follows from Eq. 1 that Qx = PcPaF. [31 The theoretical aspects of flotation kinetics were also considered by Sutherland,3 who tried to improve Eq. 1 by expressing the probability factors in terms of such physical variables as particle radius (x), bubble radius (X), velocity of bubble relative to particle (v), the number of bubbles per unit volume of pulp (N) and the induction period (A) necessary for air-mineral adhesion. According to Sutherland's treatment, the rate equation, Eq. 1, transforms to R, = [3pX x v N] [sech2 (3 v ?/4 X) ] ?c(x) V [4] where the first term in brackets on the right-hand

Jan 1, 1957

By O. A. E. Jackson

Pebble milling has been practiced in the reduction works of South Africa gold mines for well over 50 years. Originally flint pebbles were imported from Denmark to grind stamp-mill amalgamation-process tailing, which contained a good deal of extractable gold, but local operators soon found that large pieces of ore could be used for the same purpose. The ore is a hard, tough conglomerate in which quartz pebbles are cemented together by a matrix of redeposited silica interspersed with pyrite crystals. The gold, rarely visible, occurs as fine particles mostly segregated at the interface of the pebble and matrix, although a small fraction occurs within the pyrite crystals. There is seldom any gold in the pebbles themselves. Following the usual South African practice in pebble milling, Union Corp. grinds the ore wet in two or three milling stages incorporating classification. The sized broken ore used as grinding media is separated from the main ore stream in the crushing section that prepares the ore for milling. Where the ore channel, or reef, is narrow there is a shortage of large pebbles. In this case primary grinding may be done in ball mills or, more recently, in rod mills, which cost less per ton to operate. The trend, however, is to prepare finer feed for the milling section. This makes it possible to use smaller primary pebbles and eliminates the need for steel. REDUCTION WORKS OF UNION CORP. LTD. Union Corp. Ltd. exercises financial and technical control over a group of seven gold mines in the Transvaal and Orange Free State. In the Transvaal, with one exception. the mines lie 20 to 40 miles east of Johannesburg, in flat or gently rolling countryside. Winkelhaak, the first of several new mines that will be developed by Union Corp., is located in similar terrain in an entirely new gold mining district about 80 miles east of Johannesburg. Table I gives details of milling units for six of the Union Corp. mines, together with the tonnage milled in 1957. Winkelhaak Mines Ltd. is not included, as it did not begin milling until 1958. This reduction plant has no crushing section; ore is ground directly from the mine (autogenously) in 12x16-ft mills. Because these operations are still in development, they are not described in this article. It will be noted that certain reduction works have mills of more than one size in the same milling stage. This came about when plant extensions in- corporated larger units. In the case of Geduld Propty. Mines Ltd., which began milling operations 50 years ago, the primary stage is stamp milling. The reduction works follow a uniform pattern and are usually joined to the main ore shaft. Ore from other shafts is brought by standard-gage railway and dumped into a common transfer bin. The trend is to increase surface storage capacity to enable the crushing and milling sections to operate at a steady rate, independent of fluctuating ore deliveries from mine. Milling and cyanide extraction divisions of new mines are always designed to allow for extensions as mine production increases. The conveying, washing, and screening system of the crushing section is usually laid out in final form, with additional space for more crushing equipment. The crushing sections operate on one shift during early years of mine production; a second shift is introduced when the mining rate warrants it. Ample surge capacity is provided. Crushing and milling is done only on weekdays, as the law does not allow these operations to take place on Sunday in any plants constructed since 1911. The cyanide extraction sections, however, operate continuously seven days a week, drawing on mill pulp gradually built up in the thickeners during the week. Construction and equipment of milling plants follow standard practice. Dilution water is drawn from a large, high-level tank to obtain constant pressure, but gland service water for the pulp pumps is reticulated from high-pressure, two-stage pumps. The mills are equipped with the most up-to-date machinery and are designed to save labor. They compare favorably with milling plants in countries where native labor does not exist, and automatic controls are being installed wherever feasible. Hydrocyclone classifiers have replaced mechanical classifiers in modern milling plants, chiefly because of the saving in capital outlay, maintenance, and building space. The hydroclones are fed from steady head boxes rather than directly from pumps, and dilution water is introduced into these boxes. Tests have shown that in steadiness of operation and separating efficiency cyclones are comparable to mechanical classifiers. but protective stationarv screens are needed to keep the spigots clear. Rubber-lined pumps are used for pulp of about 3 mesh or finer and metal-lined pumps for coarser material. None of the Union Corp. milling plants practices gravity concentration of coarse gold by amalgamation or the use of corduroy blankets. Studies have proved that no economic case can be made for these methods, which complicate the milling process and demand extra precautions against theft.

Jan 1, 1960

By S. G. Dixit, A. K. Biswas

The flotation and adsorption behavior of ilmenite, monazite and zircon have been studied with sodium oleate as the collector and pH as the principal variable. The maxima in the flotation and adsorption properties of any of the above minerals fall within similar pH ranges. The bell shaped pH versus adsorption magnitude (r) curve is explained on the basis of collector concentration (Co and the concentration of hydroxyl ion (COH-) acting as the depressant. An equation of the type: 1 =KiCor~K2 Coh-/Coi-is proposed to account for the experimental data. The beach sand deposits along the sea coast in Southern India contain ilmenite, monazite, zircon, rutile and sillimanite as valuable minerals while quartz, garnet, shells and traces of hornblende form the gangue. A typical composition of the deposits is reported to be as follows:' Ilmenite 75%, Zircon 4-6%, Rutile 3-4%, Monazite 2 - 4%, Garnet 2 - 5% and the rest 8 -10%. Selective flotation of beach sand constituents has been reported by many workers.2-4 The fatty acid soaps have been invariably used as collectors. It is seen that all the valuable constituents of the beach sand are efficiently floated by soap collectors such as sodium oleate. In order to selectively float the beach sand constituents, it is necessary to use some depressants such as sodium silicate.3 The physicochemical parameters that govern the flotation of these minerals are yet to be studied in detail. In the present article, the findings on the parallel studies on the flotation and adsorption of the systems — ilmenite-sodium oleate, monazite-sodium oleate and zircon-sodium oleate — are being reported. In these correlative studies on adsorption and flotation of beach sand minerals, ilmenite (FeTiO3), monazite (Ce, Dy, Nd) PO4 and zircon (ZrSiO,) have been selected because they represent three important

Jan 1, 1970

By R. B. Booth, W. F. Linke

The continuous interest of the American Cyanamid Company in producing superior polymeric flocculants and dispersants for the mining industry has resulted in a broad, general study of the physical chemistry of mineral-polymer systems. The aim of this program has been to establish a sound theoretical basis on which practical problems could be analyzed, and which would lead to the development of new and improved flocculating and dispersing agents. This study has required the cooperative effort of physical, analytical, and polymer chemists, as well as engineers familiar with mining problems. This report summarizes the results of some of our investigations over the past two years. Further studies along these and other lines are in progress and will be reported in the near future. MEASURING FLOCCULATION IN THE LABORATORY The foremost problem in studying flocculation in the laboratory has been to establish reproducible methods of comparing and evaluating the effectiveness of various reagents. Previous workers have measured settling -rates 1,8 filtration rates2 , and sediment volumes3 . Direct observations of the floc size, or the clarity of the supernatant liquid, can also be used. AIthough these parameters are all interrelated, they do not always measure the same physical properties of the suspensions, and hence are not equally useful or reliable. Whatever the method of comparison selected. the testing procedure must be carefully defined and standardized. The results must be satisfactorily reproducible, and for practical purposes must accurately reflect the results obtained in mill use. In order to compare the data obtained in these various types of test, the physical nature of the flocculated system must be examined in some detail. In an unflocculated system, only the larger or denser particles (the "sands") settle at a useful rate. The sediment can be observed to build up from the bottom of the cylinder, while the fines remain in suspension for a long period of time. If the system is not disturbed, even the microscopic fines can be seen to classify themselves as they fall over a period of days. When a high molecular weight polymer is added to the system, the colloidal particles are tied together randomly in flocs, and the sands and fines settle together. The line of demarkation between solid and liquid phases moves downward from the top of the cylinder. The settling rate of the flocs depends on their size and on their effective density. For a given mineral sample, the larger the flocs, the faster the settling. Since the large flocs cannot pack as closely as small ones, they produce a sediment with more pore spaces, and hence of larger volume, which is easier to pump and to agitate. Although it is nearly impossible to measure individual floc sizes, it is relatively easy to determine settling rates and sediment volumes. Of these two, the settling rate is simpIer to measure, and hence generally more practical. Reproducible sediment volumes can only be obtained by allowing the solids to pack for a rather long period of time (e.g., hours to days), and although the volumes thus observed are directly related to the degree of flocculation (average floc size), it is often impractical to wait so long for the results.

Jan 1, 1961

By S. F. Ravitz, S. R. Zimmerley

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine. THE existence of the cobalt-copper deposits in the Blackbird district, Lemhi County, Idaho, has been known for many years. However, these deposits have not yet been exploited successfully because of the low grade of the ore, absence of information on ore reserves, and lack of feasible methods for concentrating and recovering cobalt from the ore. In 1941, when it appeared that World War II might interfere seriously with imports of cobalt from overseas, the U. S. Bureau of Mines started an extensive mining and metallurgical investigation of the Blackbird deposits. Exploration by trenching and drilling1 indicated that ore reserves were adequate to warrant consideration of large-scale exploitation. A process for producing high-grade cobalt concentrates from the ore was developed at the Salt Lake City Station of the Bureau,2 and hydrometallurgical procedures for producing cobalt metal or oxide from the concentrates were developed at the Boulder City Station.3 The Howe Sound Co., through a subsidiary, the Calera Mining Co., carried out further exploratory work, which increased probable ore reserves to a tonnage commensurate with a large investment in mine, mill, transportation facilities, and refinery. Simultaneously, the metallurgical staff of the company, working in cooperation with the Bureau of Mines, further investigated the metallurgical problems. It was the opinion of both groups that pilot-plant testing was required to translate laboratory results into plant operation. In general, the Blackbird ore has a high content of pyrite and some pyrrhotite and contains 0.5 to 1 pet cobalt and 1 to 2 pet copper, which are present essentially as cobaltite and chalcopyrite. The copper can be recovered readily as a high-grade concentrate by selective notation. The cobalt then can be recovered as a bulk sulphide concentrate assaying 4 to 5 pct cobalt, but no satisfactory procedure for separating the cobalt from the pyrite and pyrrhotite directly by flotation had been found. The method developed by the Bureau for producing a high-grade cobalt concentrate is essentially an application of the old Horwood process of selective roasting.4 The bulk sulphide concentrate is roasted to form an oxide coating on the iron mineral particles, and the calcine is then treated by flotation. The oxide coating prevents the iron minerals from floating so that it is possible to obtain a high recovery of cobalt in concentrates assaying more than 20 pct cobalt. Laboratory tests by metallurgists of both the Bureau and the Howe Sound Co. had indicated the optimum roasting temperature to be 425° to 450°C. At lower temperatures the rate of oxidation of the iron minerals is too low, whereas at higher temperatures substantial quantities of cobalt are rendered water-soluble. Because of its high sulphur content (35 to 40 pct), the bulk concentrate tends to continue to burn after it has reached the optimum roasting temperature. Although excessive temperatures could be avoided in the small-scale laboratory furnaces, there was considerable doubt that the temperature could be controlled properly in industrial equipment. To provide material for the pilot-plant tests, the Calera Mining Co. installed a small, temporary flotation mill at the Blackbird property and treated

Jan 1, 1951

By S. R. Zimmerley, S. F. Ravitz

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine. THE existence of the cobalt-copper deposits in the Blackbird district, Lemhi County, Idaho, has been known for many years. However, these deposits have not yet been exploited successfully because of the low grade of the ore, absence of information on ore reserves, and lack of feasible methods for concentrating and recovering cobalt from the ore. In 1941, when it appeared that World War II might interfere seriously with imports of cobalt from overseas, the U. S. Bureau of Mines started an extensive mining and metallurgical investigation of the Blackbird deposits. Exploration by trenching and drilling1 indicated that ore reserves were adequate to warrant consideration of large-scale exploitation. A process for producing high-grade cobalt concentrates from the ore was developed at the Salt Lake City Station of the Bureau,2 and hydrometallurgical procedures for producing cobalt metal or oxide from the concentrates were developed at the Boulder City Station.3 The Howe Sound Co., through a subsidiary, the Calera Mining Co., carried out further exploratory work, which increased probable ore reserves to a tonnage commensurate with a large investment in mine, mill, transportation facilities, and refinery. Simultaneously, the metallurgical staff of the company, working in cooperation with the Bureau of Mines, further investigated the metallurgical problems. It was the opinion of both groups that pilot-plant testing was required to translate laboratory results into plant operation. In general, the Blackbird ore has a high content of pyrite and some pyrrhotite and contains 0.5 to 1 pet cobalt and 1 to 2 pet copper, which are present essentially as cobaltite and chalcopyrite. The copper can be recovered readily as a high-grade concentrate by selective notation. The cobalt then can be recovered as a bulk sulphide concentrate assaying 4 to 5 pct cobalt, but no satisfactory procedure for separating the cobalt from the pyrite and pyrrhotite directly by flotation had been found. The method developed by the Bureau for producing a high-grade cobalt concentrate is essentially an application of the old Horwood process of selective roasting.4 The bulk sulphide concentrate is roasted to form an oxide coating on the iron mineral particles, and the calcine is then treated by flotation. The oxide coating prevents the iron minerals from floating so that it is possible to obtain a high recovery of cobalt in concentrates assaying more than 20 pct cobalt. Laboratory tests by metallurgists of both the Bureau and the Howe Sound Co. had indicated the optimum roasting temperature to be 425° to 450°C. At lower temperatures the rate of oxidation of the iron minerals is too low, whereas at higher temperatures substantial quantities of cobalt are rendered water-soluble. Because of its high sulphur content (35 to 40 pct), the bulk concentrate tends to continue to burn after it has reached the optimum roasting temperature. Although excessive temperatures could be avoided in the small-scale laboratory furnaces, there was considerable doubt that the temperature could be controlled properly in industrial equipment. To provide material for the pilot-plant tests, the Calera Mining Co. installed a small, temporary flotation mill at the Blackbird property and treated

Jan 1, 1951

By N. Arbiter, J. Steininger, C. C. Harris

Power consumption and operating variables in air-liquid systems for a wide range of operating conditions in the turbulent region have been correlated by two dimensionless groups involving the power ratio and the flow number. The form of the correlation was developed by considering flow balances related to the air-liquid composite density in the impeller zone. Data for two phase air-liquid systems, both from literature and from the present investigation, has been correlated with high statistical significance. Two phase solid-liquid and three phase gas-liquid-solid systems have also been correlated. The quantification of power requirements in the agitation of liquids is well established.1 Rushton, Costich and Everett have shown that, for mixers operating in the fully turbulent region with no vortex, the power number

Jan 1, 1964

By B. C. Mariacher

EXTRACTION of uranium from ores is being ac-complished by processes which. for the most part, subject the entire ore to acid or carbonate leaching. Ore deposits with a U 3 O 8 content below 0.10 pct U 3 O 8 are seldom considered suitable for treatment by leaching. A preliminary concentration that would enrich the uranium content of an ore by a simple, low cost process based on physical properties of the ore might result in some low grade deposits becoming commercial ores. In addition, the process might be employed in existing operations to reduce transportation and leaching costs and to increase capacity of existing leaching plants. A study to attempt the development of a preliminary concentration process for primary uranium ores was undertaken by the Colorado School of Mines Research Foundation under sponsorship of the U.S. Atomic Energy Commission. The objective of this work was to produce concentrates containing 0.25 pct U3O8 from the low grade ores tested. Ores Tested: The main effort was devoted to the low grade primary uranium ores from northwestern Saskatchewan. Samples were obtained from the Beaverlodge operation of the Eldorado Mining & Refining Ltd. Additional primary ores, obtained from deposits in Gilpin County, Colo., contained from 0.07 to 0.10 pct U3O8. Summary of Concentration Tests: The Beaverlodge ore was tested to determine amenability of the ore to concentration by magnetic, electrostatic, gravity, and scrubbing processes. None of these produced satisfactory results. Both gravity and magnetic processes produced fairly good concentrates when closely sized fractions of the ore were treated, but on the basis of treating the total ore, recovery was poor. Preparation of sized fractions and the low capacity of equipment for suitable concentration made these methods impractical. As flotation offered the advantage of treating the total ore without intermediate sizing, the main effort was in this direction. A flotation process was developed that fulfilled the concentration objectives as set by the AEC. Pilot plant testing was used to verify results obtained from laboratory batch testing. Mineralogy: A petrographic examination of the Beaverlodge ore included a study of polished sur- faces and identification of the radioactive mineral by autoradiograph and X-ray diffraction. Approximate quantitative mineral identification was as follows: quartz, 60 pct; orthoclase feldspar, 20 pct; chlorite, 10 pct; carbonates, 5 pct; and miscellaneous minerals, 5 pct. Included in this last group were plagioclase feldspar, pyrite, mica, chalcopyrite, pyroxene, sericite, magnetite, galena, and uraninite. The most general occurrence of uraninite was in the form of crusts and thin coatings on limonite-stained grains of pyrite, quartz, and pyrite-quartz intergrowth. At least 90 pct of the uraninite was still attached to other minerals in a 100 by 200-mesh size fraction. The uraninite crusts were as small as 10 to 20 µ diam, and 5 to 10 µ thick. The Flotation Process Petrographic examinations of the Beaverlodge ore had indicated the impracticability of attempting to concentrate the uranium by floating individual grains of uraninite. Liberation of the uraninite required grinding to sizes below those suitable for flotation. However, there was preferential association of the uraninite with some minerals while others were free of uraninite attachment. The approach to the development of a flotation process was, therefore, based upon an attempt to concentrate the uraninite by floating carrier minerals. The following paragraphs discuss the various stages of the process with regard to the factors tested and the conditions under which best results were obtained. Grinding: The most effective size range for flotation was —150 mesh + 13 µ. The —13 µ material in the final concentrate had a higher U3O8 content than the total ore, but not as high as the average concentrate; however, rejection of slimes before flotation was prohibitive because of the loss in uranium carried in the —13 µ fraction. Grinding techniques which contributed to a minimum production of fines, such as stage grinding, were then employed. Quartz and Silicate Depression: These minerals represented approximately 80 pct of the ore and were free to a large degree of uraninite attachment. Significant improvement in the grade of the concentrate was obtained by depression of these minerals with hydrofluoric acid or sodium fluoride. Promoter: Selective stage flotation of uraninite carrier minerals was simplified by development of a single promoter mixture. The mixture consisted of an emulsion of a fatty acid, fuel oil, and a petroleum sulfonate and was selected after a comprehensive series of tests. It contained three parts by weight of an oleic and linoleic acid such as Emersol 300,

Jan 1, 1957

By E. J. Roberts, E. B. Fitch

THE mechanism of classification by settling pools is most simply shown in the case of batch sedimentation such as was analyzed by Oden.1 The batch model will be considered, therefore, and it will be shown that the same mechanism applies to continuous operation. Classification in Batch Settling Pools: Consider a beaker or tank of slurry containing particles so dispersed that they can settle independently of one another under the influence of gravity. Originally all particle sizes are uniformly distributed throughout the suspension. All particles start immediately to settle towards the bottom at rates determined by their size, shape, and density—among other factors. Particles reaching the bottom settle out of suspension. After some given time the slurry above the deposited solids is siphoned off or otherwise removed, leaving the deposited solids behind. The deposited solids, together with entrained and any unremoved supernatant slurry, represent the underflow of a classifier. The slurry removed represents the overflow. There is a certain separation, size of particle which during the sedimentation has just time to settle from the top surface of the slurry to the level at which underflow and overflow are parted. All particles with a faster settling rate will have dropped to below this level, no matter where in the beaker they started from originally, and therefore will be absent from the overflow. Particles with a slower settling rate will not reach this level if they started from the top of the slurry, but a portion of them,

Jan 1, 1957

By B. Ball, D. W. Fuerstenau, P. C. Kapur

A two-phase distributed-parameter model of the flotation process has been extended to allow consideration of the important process parameter, concentrate grade. A simple expression is presented for the grade of concentrate in terms of the zeroth and first moments of the concentrate distribution. An example is given for a binary ore containing two pure minerals each having nondistributed rate constants. For extend-ing the model to the distributed rate constant case, a cubic polynomial zoas utilized to simulate the feed distribution. One particular example is considered and grade-recovery curves are generated to show the dependence of such curves on the initial feed distribution. Operating flotation plant engineers have traditionally evaluated plant performance in terms of the recovery of valuable mineral and the grade of the concentrate. In both operation and research, grade-recovery relationships have been used as a guide for selecting flotation conditions. Weissl illustrated the use of grade-recovery curves in plant operation and considered the grade-recovery relationship to be a metallurgical one. The extensive experimental work of Chi" using standard batch flotation tests on iron ores shows that, even with extensive statistical correlation of data, little insight can be gained into the basic fundamentals of these relations. Such relations must depend on the kinetic behavior of the various mineral species in the flotation circuit. In his flotation text book, Gaudin3 considered the relationship of recovery and of product grade to flotation kinetic indices, but he did not extend his calculations to yield grade-recovery relations. Although Gaudin used a simplistic model for his analysis, he did recognize that variations in flotation rates must result from variations in locking, surface heterogeneity, particle size and shape, among other things. In a recent paper,' we presented a model of the flotation process that could be readily analyzed with an analog computer. This model combines the concept of a distributed set of rate constants"" with that of the two-phase flotation model,8" resulting in a model more powerful and flexible than previous ones. The purpose of the present paper is to show how this model can be used to generate grade-recovery curves and to determine the dependence of such curves on the various kinetic parameters. In this paper, the model will be limited to the semi-batch case, but extension to the continuous case is a straightforward step.

Jan 1, 1971

By P. Somasundaran, D. W. Fuerstenau

This article presents the results of an analysis of grinding of 1:1 mixtures of 4x8-mesh quartz and limestone in laboratory ball and rod mills. From these experiments, the amount of energy consumed in grinding each component of the mixture was determined. In the ball mill, limestone consumes slightly more energy than quartz in the initial stages of grinding, but as the grinding proceeds quartz begins to consume a slightly greater fraction of the energy. The postulate that the fraction of energy consumed by any material in a ball mill is proportional to its volume fraction has been shown to be approximately true. On the other hand, in a rod mill energy consumption by quartz and limestone is equal only in the initial stages of grinding, with energy consumption by quartz greatly exceeding that by limestone as rod milling proceeds. Preferential energy consumption in tumbling mills has been discussed in a number of papers. For example, from an analysis of the kinetics of comminu- tion in ball mills, Arbiter and Bhrany' obtained rate equations based on the postulate that only coarse particles are ground, indicating that fine particles are protected from the action of the balls by coarser particles. In rod mills this protective action is much more pronounced than in ball mills. Recent studies on the rod milling of limestone-quartz mixtures have shown that this protective action causes the mineral with the lowest grindability (quartz in this instance) to consume the greater fraction of energy. 2 However, in the ball milling of mixtures it has been postulated that the consumption of energy by one of the constituents is determined by its volume fraction within the mill. 3 Possibly this hypothesis may be a simplification of the ball milling of mixtures since the protective action suggested by Arbiter and Bhrany may result in some preferential energy consumption by one of the constituents of a mixture. The objective of this study has been to determine preferential energy consumption in laboratory ball and rod mills by analyzing size distributions of each material in the products obtained from grinding 1:l mixtures of quartz and limestone. MATERIALS AND METHOD The procedure for carrying out the tests on wet grinding quartz-limestone mixtures has already been described.'r3 In the present investigation, 1:l mix-

Jan 1, 1963

By W. J. Tait, A. E. Craig, E. P. McCurdy

The Circuitron herein described applies current from the classifier motor circuit and energy from the sound of grinding media to move an oscillating disc. The disc through a photoelectric cell controls the speed of the ore feeder and consequently the amount of ore delivered to the mill. THE Telluride Mines, Inc. at Telluride, Colo., is operating a flotation concentrator recovering lead, zinc, and copper with some gold and silver. The nominal capacity is 500 tons per 24 hr. The ore, which comes from several different mines, is characteristic of the district, changing from extremely tough rhodonite to soft gouge. The ore is crushed and washed, recrushed, and delivered to the mill bin at about % in. to serve as ball mill feed. Details of Grinding Circuit The material from the fine-ore bin is carried over a belt feeder driven by a Reeves vari-speed device. The belt discharges to a No. 86 Marcy ball mill, which operates in closed circuit, with jigs and a 6-ft Dorr classifier. A Massco density controller holds the density of the classifier overflow at a predetermined point. The overflow, which contains about 5 pct + 48 mesh, goes to the flotation section. Manual Operation Before the adoption of automatic control for the grinding circuit, this work was all done manually by the operator. The bin gate was set to deliver 40 to 50 lb of ore per lineal foot of belt, and the speed of the belt was adjusted by the operator to deliver at the rate of about 500 tons per 24 hr. As the ore changed in hardness, specific gravity, or in the amount of moisture, or, as the size of the feed changed due to bin segregation, crusher setting, or other causes, the operator made corresponding changes in the rate of feed by manipulation of the Reeves control. Sometimes these changes occurred so rapidly that they caused sharp, pronounced surges, which created very considerable unbalance from normal conditions in the grinding circuit and, more critically, in the flotation section. Since it is not possible for the operator to anticipate or follow such changes closely, a very considerable unbalance from normal conditions may occur, which will require a drastic change in the rate of feed. These surges upset the fineness of grind and interfere radically with the balance between tonnage and reagent control. All of this tends to reduce the grade of concentrates, increase the loss in the tailing, and thus decrease the recovery of values. The Circuitron Some years ago, The Mine and Smelter Supply Co., in conjunction with the operators at the Telluride Mill, undertook to build a device that would give close control of the rate of feed from the ore bin and to coordinate with this a related device that would regulate the amount of sand load on the classifier rakes. Emphasis was strongly laid on the fact that such a control must apply to the entire grinding circuit and must include the feed to the ball mill, the classifier sand return, and the density of the classifier overflow. If this could be done successfully, we felt that the circuit could be operated under best possible conditions, with compensations

Jan 1, 1951