Search Documents

By I. WILKOMIRSKY, J. BECKER, F. Parada

Purification of molybdenite concentrate from copper concentrates was performed by sulfation. The sulfation of molybdenite concentrates was carried out with pure sulfuric acid (> 96%) at 160–190 °C to study the influence of the reaction temperature and reaction time on the residual copper in the molybdenite concentrates. A purified concentrate with less than 0.1 wt% copper and low levels of other metals were obtained. For up to 7.1 wt% copper, the conditions required are a temperature of 190 °C, a reaction time of 14 h, and a moly/acid weight ratio of 1/1. Furthermore, several designs of sulfation reactors were evaluated in order to obtain the desired level of copper in the product and to analyze the influence of the operational and design parameters on the reactor dispersion number (Le). The basic design for an 80-t/day plant fed with 4 wt% copper molybdenite concentrate requires five backmixed reactors in series, each measuring 8 m3, operating at 190 °C and with a reaction time of 10 h. The reactor must be protected against severe corrosion by the hot sulfuric acid with either Teflon, glass or ceramic.

Jun 14, 2022

By S. H. Castro

Molybdenite depression by shear degraded polyacrylamide solutions has been investigated. Aqueous solutions of polyacrylamide-type flocculants were subjected to shear degradation under a range of high-speed stirring conditions. Settling tests, carried out with quartz slurries and sheared polyacrylamides, showed reduced flocculant performance with increased degradation. As the sedimentation rate is strongly dependent on the polymer's molecular weight, these results fit well with the shear degradation theory, which predicts the production of shorter chain segments due to breakage of the polymer macromolecules. Microflotation tests on natural molybdenite showed that the depressing ability of a commercial polyacrylamide flocculant remained unaltered after shear degradation, even when the flocculating ability was entirely lost. Practical implications of shear degradation on molybdenite flotation are discussed.

Jan 1, 2004

By M. Kolahdoozan, H. Noori

"Molybdenite flotation at the Sarcheshmeh Copper Complex has been studied as a function of pulp potential controlled using two types of sodium sulfide (mineral and chemical origin). Air and either plant or laboratory nitrogen was used as a flotation carrier. Potential measurements were taken in the rougher cells as it was proved to be vital for molybdenite flotation. Flotation test with reducing potentials between -525 and -575 mv gave the highest molybdenum recovery (93%) and the lowest copper recovery of between 4 to 15% can be achieved. These potentials did not change considerably by adding increasing amounts of sodium sulfide. At more oxidizing potentials, i.e. more than -450 mv, the recovery of copper increases while the recovery of Molybdenite drops.INTRODUCTIONThe average copper ore feed grade to the Sarcheshmeh flotation circuit is typically set at about 1.2% Cu. to be delivered to processing unit is set at 1.2%. There is no control of molybdenum (Mo) which usually varies between 0.01 and 0.04%. During concentration, a Cu-Mo concentrate is produced by one stage of roughing, one stage of scavenging and two stages of cleaning. Final concentrate contains 0.5% of Mo and 32% of Cu while the particle size is 90% under 42 microns (325 mesh). Because of the high grade of Mo in this concentrate and economic interests, a molybdenite flotation circuit plant was built in 1984. This plant was designed to treat 1432 tons of Cu-Mo concentrate (on dry basis) and consists of one stage of roughing followed by seven stages of cleaning. After dewatering the concentrate contains 53.7% Mo which is dried and shipped overseas.The majority of molybdenite production worldwide comes as byproduct of copper porphyry ores. The Mo grade typically varies between 0.01 and 0.06% and accompanies chalcopyrite and chalcocite. Due to the hydrophobic nature of molybdenite, it can be floated along with copper sulfides. Thus the overall concentrate of Cu and Mo contains 0.2-1% of molybdenum as well as 20-42% of copper. To separate the Mo, Cu and Fe minerals, depressants are used. The most important of which are sodium sulfide, sodium hydrosulfide, Anomal D, sodium cyanide, ferropottasium and ferro-cyanide. The first three regeants have been extensively used for successfully treating porphyry ores [1]. In the molybdenum plant of the Sarcheshmeh Copper Complex only sodium sulfide has been used to date."

Jan 1, 2006

By Y. Ye

Typically, rougher molybdenite flotation and recovery from bulk copper/ molybdenum concentrates involves the use of alkalisulfides, Nokes reagents, cyanides, oxidants, and/or thermal treatment for the depression of copper sulfide minerals. The bulk copper/molybdenum feed generally varies from 0.2% Mo to 1.0% Mo, and with traditional reagents the single-stage rougher flotation recovery of molybdenite varies between 40 and 90% at a concentrate grade of 5 to 10% Mo. With ozone conditioning for copper depression, however, improved separations appear to be possible, as demonstrated by tests with Cu/Me concentrates from both the Phelps Dodge Morenci Operations and the Kennecott Copperton Operations. Single-stage rougher flotation after ozone conditioning can provide a molybdenum concentrate at a recovery of more than 90% and a rougher concentrate grade higher than 20% Mo in some cases. Subsequent cleaner flotation with additional ozone conditioning results in relatively copper-free molybdenum concentrates containing as much as 52% Mo. Preliminary analysis indicates that, with a multistage ozone conditioning/flotation strategy, the process is technically and economically viable and should be suitable for industrial application.

Jan 1, 1990

By H. H. Claudet

PROBABLY the first flotation mill for treating molybdenite ores was put into operation .in Norway during 1913, when the writer was employed to introduce and apply the Elmore vacuum flotation process at a mine in southern Norway. These operations proved successful and led to other similar installations in that country. It remained, however, for Norwegian engineers themselves to iron out their difficulties and establish the molybdenum industry on a basis which ultimately attained world importance. Just as today, an urgent demand for molybdenum arose during the world war of 1914-18. By 1916, many molybdenite properties were in operation in Canada and several small concentrating mills were under construction. At one of these, in the Ottawa Valley district, the opportunity came for applying the Elmore vacuum flotation process, using a flow-sheet similar to that adopted in Norway. Later, as one of the staff of the General Engineering Company, who had already developed a highly efficient flowsheet for treating molybdenite ores, using the Callow pneumatic flotation process, the writer devoted considerable time to research work and investigations on a number of molybdenite projects and deposits in eastern Canada. The bulk of Canada's production of molybdenite was coming at that time from the Moss mine at Quyon, Que., where concentration of the ore was effected by water-film flotation. It is of interest to note that this process, based on the principle of surface tension, had been developed and introduced by the late Henry E. Wood, of Denver, Colorado- one of the original owners of the Moss mine-at the time he was investigating the Elmore vacuum process in his Denver plant. The process, with certain modifications, was used at several other properties in eastern Canada, and notably in the ore dressing laboratories of the Department of Mines at Ottawa and in a plant at Renfrew, Ont., in both of which ore from deposits in various parts of Canada was treated, with recovery of very appreciable amounts o much needed molybdenite. During the summer of 1917, the water-film flotation mill at the Moss mine was dismantled and the plant was re-modelled by the General Engineering Company to include the Callow system. This installation, using improved flotation methods, was highly successful both as to recovery and grade of concentrate, and proved a decided advance in molybdenite concentration, a recovery of upwards of 90 per cent being obtained, with a concentrate grading over 90 percent MoS2.

Jan 1, 1944

By D. F. Haley

THE molybdenite deposits at Climax, Cool., have recently attracted considerable notice, because of their great size, as compared with other known deposits of the same mineral. Climax station, on the. Colorado Southern narrow-gage railway, was at one time the Fremont Pass station on the Denver & Rio Grande. It is 1412 miles northeast of Leadville, and exactly on the divide between the headwaters of the Arkansas and Blue Rivers. Climax station is 11,300 ft. (3444 m.) above sea level. The working tunnel of the molybdenum mine is about 1 mile from the railroad, and 900 ft. above it, at an elevation of 12,200 feet. The climatic conditions are severe, and snow can be expected during any month of the year. Winter sets in not later than Nov. 1, the snowfall is very heavy, and the ground remains covered with snow until June 1, and sometimes even later. From June 1 to Oct. 1, there is much rain and a little snow falls in the late afternoon nearly every day. In October, 1917, there was one of the biggest snowstorms and blizzards of the year. Being just on the divide, constant strong winds blow the fine, dry snow with such force that, during most of the winter, outside work of any kind -is accomplished under most trying conditions. Within a few miles of Climax, some of the richest gold placers of Colorado occur. One of them, McNulty Gulch, was just across on the northeastern flank of Bartlett mountain. This mountain, therefore; was well prospected, and the presence of a bluish mineral and a yellowish one resembling sulphur was known to the old prospectors. They thought for many years that the blue mineral was graphite, and it is difficult to say when it first became definitely known that it was molybdenite. Claims had been staked as .early as 1896, but it is evident that the prospectors at that time were looking for gold. In 1902; several claims were acquired by H. Leal, who drove a tunnel about 900 ft. (274 in.) long, probably to intersect a fault, which shows on the surface, and was thought to be a possible gold carrier. Gold was not found in paying quantities, but throughout its length the tunnel passed through a fractured silicified granite, showing a fairly uniform distribution of a fine-grained bluish mineral, which was finally determined as molybdenite. For several

Jan 8, 1918

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. Contrary to most copper sulfide minerals where recovery is principally liberation controlled, the recovery of molybdenite is much more complex with fully liberated particles commonly lost to tailings. It is this complexity that facilitated the necessity for a geometallurgical investigation of molybdenite from the Bingham Canyon deposit. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes (i.e. morphology, angularity, liberation, size) have on the recovery of molybdenite in the processing circuit. A set of samples was collected from the ores and products produced by Rio Tinto Kennecott’s Copperton Concentrator. All samples were analyzed using normal polarized reflective light, Mineral Liberation Analyzer (MLA) and X-ray diffractometery (XRD) techniques. The results of this investigation revealed the presence of two distinctly different types of molybdenite, which have been identified as the two polytypes of molybdenite, i.e. hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the core of the Bingham Canyon deposit. The 3R polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Concerning their metallurgical behavior each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. For instance, the 2H polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high quality molybdenum concentrate under normal operating conditions common to most copper concentration operations. In contrast, the 3R polytype is difficult to grind and kinetically “slower” floating with surface attributes that less amenable to recovery under normal operating conditions. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to the normal operating parameters may be necessary to improve the recovery of molybdenum. Finally, a preliminary investigation into the metal budget of porphyry Cu and Mo deposits indicates that a positive correlation may exist between the total economic metal budget and the polytype content. For example, higher concentrations of the 3R polytype appear to be more prevalent in Au-enriched porphyries versus Mo-enriched porphyries. This observation may also serve to help explain why it is easier to obtain high rates of recovery in Mo ± W-rich deposits, which contain little to none of the 3R-polytype. Consequently, the potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present, as well as its impact on the economics (exploration) and/or on the processing circuit (plant design) could exist. In conclusion, this investigation highlights the necessity of understanding the mineralogical properties or characteristics of molybdenite and/or other economic mineral(s), as these can and will have a direct impact upon the performance and plant optimization."

Jan 1, 2016

By R. Craig McClung

Contrary to other sulfide minerals, where recovery is principally liberation controlled, the recovery of molybdenite is more complex. It is this complexity that initiated a geometallurgical investigation of molybdenites from Bingham Canyon. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes have on recovery. All samples were analyzed using normal mineralogical techniques. The results reveal the presence of two distinctly different types of molybdenite. These have been identified as the two polytypes of molybdenite: i.e. hexagonal (2H); and rhombohedral (3R). The 2H-polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the current pit bottom. The 3R-polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance and are concentrated along the margins of the current pit. Concerning their metallurgical behavior, each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. The 2H-polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This results in the production of a high quality concentrate under normal operating conditions. The 3R-polytype, by comparison, is difficult to grind and kinetically “slower” floating with surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R-polytype, modifications to the normal operating parameters may be necessary to improve recovery. This investigation highlights the necessity for understanding the mineralogical characteristics of any economic mineral(s), as these will have a direct impact on recovery.

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. While the recovery of most copper sulfide minerals is principally liberation controlled, the recovery of molybdenite is much more complex, with fully liberated particles commonly lost to tailings.A geometallurgical investigation was undertaken of molybdenite from the Bingham Canyon deposit with the aim of determining what effects, if any, mineralogy and the mineralogical attributes of morphology, angularity, liberation and size have on molybdenite recovery in the processing circuit. A set of samples was collected from the ores and products of Rio Tinto Kennecott’s Copperton Concentrator. The samples were analyzed by normal polarized reflected light microscopy, X-ray diffractometry, and scanning electron microscopy using a Mineral Liberation Analyzer, revealing the presence of two distinct types of molybdenite, which are the two polytypes: hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins located in the core of the deposit, while the 3R polytype occurs as disseminated, ball-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Each polytype exhibited metallurgical properties consistent with those reported in the literature. The 2H polytype is easily ground, kinetically “faster” floating and displays surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high-quality molybdenum concentrate under normal operating conditions at most copper concentration operations. The 3R polytype is difficult to grind, kinetically “slower” floating and displays surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to operating parameters may be necessary to improve the recovery of molybdenite.A preliminary investigation into the metal budget of porphyry copper and molybdenum deposits indicated a possible positive correlation between total economic metal budget and polytype content. Higher concentrations of the 3R polytype appear to be more prevalent in gold-enriched porphyries than in molybdenum-enriched porphyries. This may help explain why it is easier to obtain higher rates of recovery in molybdenum ± tungsten-rich deposits, which contain little to none of the 3R polytype. There is a potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present as well as its impact on the economics, in terms of exploration, and the processing circuit, in terms of plant design."

Jan 1, 2016

By D. M. Podobnik, J. F. Shirley

The Cuajone Concentrator of the Southern Peru Copper Corp. is located approximately 900 km southeast of Lima, Peru, near the 500 year old town of Moquegua, in an area that has been occupied since antiquity since the plant was started in July, 1976, the throughput has steadily increased from 36 to 46 kt/d (50,7055tpd). The widely distributed molybdenite content of the ore body ranges from 0.02-0.4% MoS2. The molybdenite content of the copper concentrate has always been sufficient to justify operation of a byproduct molybdenite plant. During the first nine months of 1980, the average grade of the ore was 1.169% copper and 0.026% molybdenite. Pilot plant testing conducted during 1970 at Toquepala, Cuajone's sister plant, determined that the recovery of the molybdenite into a salable concentrate could be accomplished relatively easily by using the Asmol process. Experience gained at Toquepala, which converted to Asmol in 1969, confirmed the simplicity of process. Simplicity of operation was one of the major criteria for the process selection because, at the time, it was expected that the molybdenite plant would start up concurrently with the copper concentrator. Other processes studied either produced inferior results or were judged more difficult to operate. However, geological information indicated that the molybdenite content of the ore would be relatively low for the first couple of years of operation, so the design and construction of the plant was delayed until after the copper plant was in production. Asmol remained the process selection. During 1976 and 1977, the flowsheet and plant layout based on pilot plant data, new results obtained from Cuajone's metallurgical laboratory, and process improvements from Toquepala's experience were completed. One of the more important innovations from the Cuajone laboratory was that the Asmol consumption could be substantially reduced by replacing air with nitrogen gas in the rougher and first cleaner flotation steps

Jan 1, 1983

By Donald M. Podobnik

The Cuajone Concentrator of the Southern Peru Copper Corporation is located approximately 900 kilometers southeast of Lima, Peru, near the 500 year old town of Moquegua, in an area that has been occupied since antiquity. Since the plant was started in July, 1976, the throughput has steadily increased from 36,000 to 46,000 metric tons per day. The widely distributed molybdenite content of the ore body ranges from 0.02 to 0.04% MoS2. The molybdenite content of the copper concentrate has always been sufficient to justify operation of a byproduct molybdenite plant. During the first nine months of 1980, the average grade of the ore was 1.169% copper and 0.026% molybdenite.

Jan 1, 1981

By R. S. Archer

THE name molybdena was employed by Pliny to denote various substances resembling lead. Later this name was applied to galena-the naturally occurring sulfide of lead-or substances of similar appearance. By the middle of the eighteenth century, it was applied to graphite and to the mineral sulfide of molybdenum (MoS2) now called molybdenite. This confusion is quite understand- able inasmuch as these substances look and feel very much alike. In 1778, the Swedish chemist Scheele published a treatise in which he pointed out essential differences between graphite and molybdenite. On treatment with nitric acid, molybdenite, unlike graphite, produced a peculiar white earth with acidic properties which he called molybdic acid. Since the same mineral gave off sulfurous fumes on heating, he concluded that it was a sulfide of molybdenum. In 1790, there appeared an account of the isolation by P. J. Hjelm of the new element molybdenum, as a metallic powder, by heating the oxide with carbon. It was not until Bertelius conducted the necessary experiments, about 1818 to 1825, that the foundation of the chemistry of molybdenum was laid. The only recorded use of molybdenum during the first century after its isolation was as a chemical reagent, primarily for the determination of phosphorus. It was not until the last decade of the nineteenth century that the use of molybdenum in steel appears to have been investigated. A

Jan 1, 1953

By L. F. McHugh

Molybdenum conversion operations discussed in this paper encompass all major operations commercially used to upgrade molybdenite concentrates to various refined products. More emphasis is placed on discussion of key pyrometallurgical unit operations. These operations conducted at Metec include roasting, sublimation, and hydrogen reduction

Jan 1, 1986

By Charles "Chick" Rodgers

"The Key Lake uranium mine is the largest single uranium producer in the world. It is owned 2/3 by Cameco Corporation and 1/3 by Uranerz Exploration and Mining. Cameco is the operator. Current production is fourteen million pounds per year of uranium oxide (U308).The mine's location is 570 kilometres north of Saskatoon on the southern edge of the Athabasca Basin approximately at latitude 57° 11 'north and longitude 105° 34' west. Access to the mine is by an all-weather road and a private airstrip.The mill was commissioned in 1983. A molybdenum plant was constructed in 1989 in response to increasing molybdenum content in the yellowcake or final product. Early test work had showed that the first ore body to be mined, the Gaertner deposit, would present few problems with regards to molybdenum in the product. However, the test work also showed that the higher molybdenum content of the Deilmann ore, the second Key Lake orebody to be mined, would result in increased molybdenum concentrations. Without the molybdenum plant, penalties would become excessive and some product might not accepted by the refineries.This paper will describe the current Key Lake mill process with emphasis on the molybdenum solvent extraction process. It will cover the chemistry of the process, process development in the mid 1980's, and current operating practices.The Key Lake milling process consists of five individual plants, crushing and grinding, leaching -counter current decantation (CCD), solvent extraction, yellowcake/crystallization and bulk neutralization (Figure 1. Simplified Mill Flowsheet). A detailed mill flowsheet can be found in the appendix."

Jan 1, 1996

By D Jensen, L Riffo, S Yu, F Traczyk, D Meadows

With the steady increase of molybdenum demand worldwide and the favorable molybdenum market, many technological innovations on both process and equipment have been developed and applied in many modern molybdenum plants around the world. This paper introduces the most commonly used molybdenum flotation flowsheet, together with the introduction of the flotation chemistry. Many different types of flotation cells are used in modern moly plants, and each type of flotation cell has its own unique advantages suited for particular ore and process conditions. This paper tries to provide some insight and guidelines in flowsheet development and flotation cell selection in the molybdenum plants.CITATION:Meadows, D, Jensen, D, Traczyk, F, Yu, S and Riffo, L, 2013. Molybdenum flotation circuit and flotation cells, in Proceedings MetPlant 2013 , pp 387-398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

Several of the larger copper projects recently built have included a molybdenum byproduct circuit as part of the overall project due to the favorable molybdenum market conditions and overall economic contribution to the project. This paper provides a summary of moly plant flotation practices across a number of both recent projects and historical ones. Modern Molybdenum flotation flowsheets predominantly incorporate self-aspirated cells and forced air cells with nitrogen addition. The paper provides insight into the process considerations, capital and operating costs associated with both of the cell types. It also reviews metallurgical aspects and important safety aspects. Other aspects including instrumentation and degree of automation are also discussed along with overall plant design.

Feb 27, 2013

By D. L. Morgan, J. A. Butterfield

"Geological data, production trends and current projects underway suggest that enough molybdenum will be available from more diversified sources to meet the world's growing demands. The growth in molybdenum consumption has been primarily related to its beneficial effects as an alloying agent in steel. This rapid growth has been deliberately fostered by stable prices, adequate supply and application research. The molybdenum industry is now in a process of change which has been seen in several other metals, such as aluminum and nickel. As supply sources have become more diversified, the market has become more competitive. The recent drop in consumption has led to excess production capacity, accumulation of substantial producer inventories and increased market uncertainties. While consumption is expected to increase in the next two to three years, it will take some time to absorb the excess capacity and inventory. The increased proportion of by-product capacity indicates that prices may become more variable. Producer discipline will be required to prevent serious price erosion in times of surplus. Future prices may not continue to increase with inflation. For the longer term, several factors favour the increased consumption of molybdenum. Engineering requirements are becoming more severe and molybdenum alloys can help to meet these changing needs. In addition, consumers can rely on a large and increasing supply of molybdenum. A 7 per cent growth rate in consumption can probably be sustained through the next decade, but new applications and reasonably stable prices will be needed to make this possible."

Jan 1, 1972

By J. Andres

"Freeport-McMoRan’s Sierrita operations refines molybdenum disulfide in a ferric chloride leach to remove impurities. To understand bottlenecks in the leach process and the true capacity of the leach system, a cross-functional team was established to look at theoretical models, kinetics of the leaching process, equipment limitations and operational strategies. A series of in-plant tests were run which resulted in a road map for improved throughput. INTRODUCTION Molybdenum, a vital component in the steel industry, is often found in nature as molybdenum disulfide (MoS2). Molybdenum disulfide deposits can exist as standalone components in an ore body, or can also be found within copper porphyry nodes. Processing for these copper/molybdenum porphyry ore bodies involves a first stage of flotation to produce a bulk concentrate before separation of the copper and molybdenum concentrates in a second stage of flotation. In this second stage of flotation, a reagent is added to suppress the copper particles, while allowing the molybdenum disulfide particles to remain hydrophobic and continue to float. This separation is very good at keeping the molybdenum out of the copper concentrate; however a portion of the copper continues to float through the circuit. As a result, there is typically some amount of copper in the final molybdenum concentrate. This copper must be removed in order for the molybdenum disulfide product to meet product quality specifications. Once the raw molybdenum disulfide product has been made, a separate process must be applied to remove any copper, lead, or other impurities remaining in the concentrate. This process usually involves the selective leaching of impurities out of the bulk solid. Gupta mentions three specific types of leaching agents, sodium cyanide, ferric chloride, and hydrochloric acid for the removal of sulfide impurities. Sodium cyanide is useful for the removal of copper compounds such as bornite, covellite, and chalcocite.1 Sodium cyanide solution dissolves these copper compounds, and the remaining molybdenum solids are filtered to produce a pure molybdenum concentrate. Ferric chloride works similar to that of sodium cyanide, but is particularly efficient in removing chalcopyrite and galena compounds. These compounds are easily chlorinated at elevated temperatures, producing copper chloride and lead chloride, through the reactions presented below:"

Jan 1, 2015

By C. H. B. Leitch, T. N. MacAuley, R. L. Linnen, A. E. Williams-Jones

"The Trout Lake stockwork molybdenum deposit is temporally and spatially related to the emplacement of a late Cretaceous granodiorite-tonalite stock in southeastern British Columbia and contains an estimated 49 million tonnes grading O.I9% MoS2- No metal zonation patterns are apparent, with the exception of peripheral tungsten skarn, and exploration was guided largely by geological interpretation. It is typical of the granodiorite, or fluorine-poor type of molybdenum deposit. Molybdenite is contained within a quartz-feldspar vein stockwork and coeval dissemination in igneous (and less commonly metasedimentary) hosts. In general, molybdenite is strongly associated with alkali feldspars, but in detail it is intimately associated with incipient muscovite replacement of albite and K-feldspar; veins that lack feldspars are also typically barren of molybdenite. These textures suggest that fe/dspathic alteration (and precipitation in veins) was an important precursor to mineralization, and the occurrence of similar textures elsewhere (e.g. Henderson) suggest that early feldspathic alteration is important to the genesis of molybdenum deposits in general. Molybdenite deposition at Trout Lake was preceded by contact metamorphism, skarn and potassic alteration, and was overprinted by muscovite-ankerite (phyllic) alteration. Only moderate temperature changes are recorded by the metamorphic and alteration mineral assemblages (350°C to 450°C}; however, with time, fluids became increasingly more acidic and enriched in C02- In light of the intimate molybdenitemuscovite intergrowths, the decrease of pH probably exerted a major control on mineralization.IntroductionGranite-hosted molybdenum deposits can be classified in terms of the composition of the related intrusion, e.g., the granodiorite and granite types of Mutschler et a!. (1981), or the calc-alkaline, alkali-calcic, and alkalic types of Westra and Keith (1981). They have also been classified on the basis of their fluorine contents (Theodore and Menzie, 1984) with the fluorine-rich and -poor varieties roughly corresponding to granite- and granodiorite-type deposits, respectively. For economic reasons, most exploration and research has concentrated on the high-grade/large tonnage granite-type of deposit, exemplified by Climax. F1uorine-poor, granodiorite-type deposits are, however, the most common type in Canada and have been mined in the past (e.g., Endako). In this paper, the authors summarize the research that has been carried out on the fluorinepoor Trout Lake deposit (Boyle and Leitch, 1983; Linnen, 1985; Linnen and Williams-Jones, 1987; 1990) and use what has been learned to develop guidelines for the future exploration of fluorinepoor, granodiorite-type molybdenum deposits."

Jan 1, 1995

By J. Andres, M. Cross

"Freeport-McMoRan’s Sierrita operations has two natural gas-fired molybdenum roasters for converting molybdenum disulfide into molybdenum trioxide. When these roasters were compared to other similar units within the company during a benchmarking exercise, it showed that increased throughput from the roaster units at Sierrita was possible. A team of site metallurgists, technical experts from other sites, and engineers from the Climax Technology Center was formed to study the potential in more detail. The team investigated many parameters in the roaster, including temperature profiles, roaster chemistry profiles, rabble and drop hole patterns, and operational strategies. The results of these studies and the associated throughput improvements are described in this paper. INTRODUCTION Molybdenum, a vital component for the steel industry, is typically found in nature as molybdenum disulfide (MoS2). MoS2 is typically recovered via flotation processes and is purified through leaching processes. While molybdenum disulfide is a commercial product, it is not the form of molybdenum that the steel industry requires. They require molybdenum in the form of molybdenum trioxide, MoO3. There are multiple ways to refine molybdenum disulfide into molybdenum trioxide. The primary method is the oxidation of molybdenum disulfide in a multiple hearth roaster. The chemistry of converting molybdenum disulfide to molybdenum trioxide is very favorable at increased temperatures, oxidizing the molybdenum through a range of exothermic reactions to ultimately produce MoO3. The chemical reactions that occur in molydenum roasting occur in three zones. These three zones correspond with four different reactions."

Jan 1, 2015