Search Documents

By F. G. Miller

It is generally accepted that sulfur exists in coal in three forms: (1) pyritic, (2) organic, and (3) sulfate sulfur. Sulfate sulfur usually makes up less than 1% of the total sulfur content. Pyritic and organic sulfur, make up almost all of the total sulfur and occur in varying amounts in different coals and can vary greatly in coal of the same seam Pyritic sulfurs of 20% to 80% of the total sulfur have been reported Other authors have shown that it is not possible to remove the organic sulfur without chemically altering the coal. Chapman and Jones (1) state: "Organic sulfur, unlike pyritic sulfur does not exist as discrete particles, but is intimately associated with the coal structure, and as such it is not possible to remove it or reduce its concentration by physical means." Any success in removing sulfur has come about by removing pyritic sulfur by physical means; therefore, removal of sulfur in the pyritic form is the subject of this investigation. The extent to which any impurities can be removed from a particular coal can be determined by a washability study. Outside of crushing coal, to finer sizes or chemically altering the coal, there are no known methods of changing this inherent washability characteristic. The efficiency of various methods used to remove impurities can be determined by comparison of results produced at a yield to the results as shown by a washability study. In recent years heavy media processes have proven their ability to wash plus 28 mesh coal and nearly produce results shown to be theoretically possible by the washability study. Therefore, it is the objective of this paper to show various methods of treating the finer fractions of the coal, in the hope of developing a process, which can effectively produce in the fine fractions the efficiency of heavy media devices in the coarse.

Jan 1, 1963

By George I. Staber

As stated by the Congress in the preamble of the act establishing the Office of Coal Research, its purpose is, "To encourage and stimulate the production and conservation of coal in the United States through research and development by authorizing the Secretary of the Interior to contract for coal research, and for other: purposes." Thus, while the overall responsibility for air pollution control from all sources rests primarily with the Department of Health, Education and Welfare, it is obvious that OCR could not perform its mandate of, increasing the utilization of our Nation's greatest energy resource if it ignored one of the greatest practical obstacles to achieving that objective. Therefore, air pollution abatement and prevention is one of the practical considerations taken into account in the selection of the OCR program. And as the severity of the air pollution problem imposes new restrictions on the use of coal, the importance of this criteria in the selection of OCR projects increases. The work done by OCR in air pollution abatement does not conflict with nor does it duplicate the program developed by HEW's National Center for Air Pollution Control. Technical members of the OCR staff maintain close formal and informal liaison with their counterparts in NCAPC. One formal agreement has been executed whereby the HEW agency has transferred funds to OCR for a practical study of the potential effectiveness of air pollution control when coal is burned in a fluidized bed comprised of inert alkaline earth material. It is hoped that this initial cooperative effort will be

Jan 1, 1968

By Thierry Bernard

Considering rock fragmentation by explosive as the ultimate goal in mines and quarries, vibrations are definitely one of the main drawbacks faced by the Industry. If we can accurately predict vibrations level and frequencies, taking into account the whole set of the involved parameters, this will bring a major benefit to each of us, in our daily production process optimization effort. The model presented in this paper answers to this need thanks to a "holistic" approach of the vibration mechanism. By holistic, we mean that we approach the vibration effect (wave propagation) as a whole, by understanding all of the mechanisms that contributes to the process and comprehending how they are connected.

Jan 1, 2009

By K. Hodgson, J. P. M. Hojem, N. G. W. Cook

Already about one-third of South Africa's coal is mined at depths exceeding 100 metres. Almost all this mining is done by the bord and pillar method. Conventional design procedures call for ever larger pillars as depths of workings increase, resulting in the loss of large amounts of coal and reductions in productivity. Barrier pillars are in general use to ensure against large collapses. The presence of these strong pillars would allow a more efficient design of the bord and pillar layout to yield improved extraction ratios by using smaller, yielding, pillars between the bords. Knowledge of the complete load- displacement curves for such pillars is a prerequisite for the design of such a system. A 100-MN, stiff jacking system for measuring the complete load-displacement curves of pillars with cross-sections of up to 2 m X 2 m is described. The jacks are installed in a slot cut across the central plane of symmetry of a pillar, thereby ensuring that the stress distribution in the pillar during a test, especially at its contacts with the roof and floor, is identical to that caused in a similar pillar by convergence across the seam. Preliminary results in the form of complete load-displacement curves for test pillars of about 1.5 metre square section are given.

By Tim M. Benson, Adam L. Lamanna, Carolina Martinez-Gutierrez, Mark J. Stephani

The Lower Concourse C Extension (LCE) 108-in Storm Sewer consists of a 2,797-foot long, 27 to 55-foot deep, 108-in I.D. storm sewer tunnel. Situated beneath active taxiways and a terminal apron at Hare International Airport (D), the tunnel diverts ows from existing storm sewers located within the footprint of a future satellite concourse. The project was delivered via Construction Manager at Risk (CMAR) as part of Chicago Department of Aviation’s (CDA) ongoing O’Hare 21 Capital Program. This paper presents project details, multiple stakeholder coordination, subsurface risks and challenges, TBM performance, and impacts to existing infrastructure.

Jun 23, 2024

By Serhat Baycan, Mikias Yohannes

"Kuala Lumpur Karst is a complex limestone formation that is characterized by presence of cavities, solution channels, pinnacles and floaters. Basement excavations in such geological formations are usually challenging, mainly owing to the unpredictable rock head depths and potential for groundwater inflow. Any excavation support system should have adequate robustness and water tightness. Traditionally, Secant Bored Pile walls (SBP) with struts are the preferred option for karst ground. This paper discusses a cost effective and innovative alternative solution for a particular site – using Deep Soil Mixing (DSM) and using Contiguous Bored Piles (CBP) together with Ground Anchors (GA). The site, located around one of the busiest areas of Kuala Lumpur, is a 5,700 m2 commercial and residential development. A 16.0 m deep excavation was needed for four levels of basement and excavation support along the 275 m perimeter of the development. Within the site, the depth to rock head varied from 6 m to 19 m. The basis for each solution and conditions for its suitability are discussed in detail. Some design considerations and construction challenges are also presented. The performance of the two retention systems during excavation are presented, together with comparisons versus design predictions. Suggestions for future development are also given. Advantages of this approach compared to other traditional approaches are highlighted.1. INTRODUCTIONThe geology of Kuala Lumpur is among the most complicated and geotechnically challenging formations in South East Asia. The majority of the city falls into the Kuala Lumpur Limestone formation; which is a thick, highly-weathered and cavernous limestone. This formation is pure calcitic to dolomitic in composition, having infrequent schist and phyllite interbedding (Gobbett et al., 1973).The KL limestone has a highly karstic topography dotted with cavities, ravines, interconnected subterranean channels, pinnacles, overhangs, floaters and slump zones (Tan, 2006). This results in erratic bedrock profiles even within short distances. It is not uncommon to see a precipitous rock head incidence within short distances in the same site. In most parts of the City, the bedrock is typically encountered ranging from very shallow depths to about 30.0 m. The exception to this is at the heart of the City, where Kenny Hill formation prevails above the KL limestone. In such cases the limestone bedrock can be encountered much deeper. The erratic rock head profile and the highly karstic nature of the KL limestone makes it a geotechnical challenge requiring careful consideration of suitable engineering solutions.1.1 – Site DescriptionThe site, located in downtown Kuala Lumpur, is abutted by a busy street on the North. Before development, the site previously served as a car park. To the west an access road separates the site from an empty lot; while on the east, the lot is bounded by light weight residential and commercial buildings. On the south side, the site is bordered by a road that separates it from a prominent Shopping Mall in the City. A layout plan and an artist’s impression of the finished development is shown in Figure 1."

Jan 1, 1900

By Abhishek Asthana

The incineration of Municipal Solid Wastes (MSW) is an attractive process for reducing the volume of the wastes and recovering their energetic value, which, however, requires to be strictly controlled in order to limit its impact on the environment. In this context, we have undertaken the mathematical modeling of the different sections of a typical incineration plant. The combustion of the waste bed, usually carried out on a moving grate, is at the core of the process. This paper presents the 2-dimensional, steady-state model that we have developed for simulating the MSW combustion. The model describes gas flow through the porous waste particle bed, the gas-solid reactions, conductive and radiative heat transfers, drying of the feed, its pyrolysis and the emission of volatile species, combustion of the pyrolysis gases, the formation of char and its gasification by water vapor and carbon dioxide, and the consequent reduction of the bed volume. Pyrolysis kinetics distinguish between cellulosic and non-cellulosic materials and are experimentally derived from our laboratory measurements. The calculated results give a deep insight into the various involved phenomena, an example being the complete consumption of oxygen in a large zone of the bed and the related appearance of a char gasification zone. The influence of various operating parameters, like the temperature and flow rate of primary air, is presented and explained. Finally, the effect of stirring the waste bed on the moving grate is also analyzed.

Jan 1, 2006

By E. Pribonic

Failure of a mine material hoist can cause injuries, fatalities and significant infrastructure damage, along with an associated loss of production. Principal causes of hoist accidents are overwind and underwind. Past and present means of arresting hoisting equipment are marginally effective and utilize destructive systems that are not reusable following an arrest. The use of permanent magnet eddy current arrestor technology is proposed; the history and fundamental science of the technology are presented, followed by real world examples and calculations of performance for failsafe, friction-free, instantly reusable eddy current arrestors as applied to stopping a 30-ton ore skip traveling at 16 metres per second. A comparison of existing arrestor types with the eddy current arrestor is included and limitations of the ECA are also discussed.

Jan 1, 2008

By H. Y. Sohn, M. Pérez-Tello, P. J. Smith, K. M. Riihilahti

A three-dimensional computer model for the Kennecott-Outokumpu flash converting process for copper matte is presented. The model incorporates the transport of momentum, heat and mass, and reaction kinetics between the gas and particles in a particle-laden turbulent gas jet. The k-E model is used to describe gas-phase turbulence in an Eulerian framework. The particlephase is treated from a Lagrangian viewpoint which is coupled to the gas phase through the source terms in the Eulerian gas-phase governing equations. Matte particles were represented as Cu2S·yFeSx. Based on experimental observation, the oxidation products were assumed to be Cu2O, CuO, Fe3O4, and SO2. A reaction mechanism involving the external mass transfer of oxygen to the particle surface and diffusion of the oxygen through the oxide layers of CuzO/Fe304 and CuO/Fe3O4 is proposed. Predictions of the mathematical model were compared with the experimental data collected in a large laboratory furnace. A reasonable agreement between the model predictions and the measurements was obtained in terms of fractional conversion of the oxidation reactions and of sulfur remaining in the reacted particles. The simulation of an industrial flash converting furnace was also performed. Higher oxidation rates, more even distribution of particles, and thus a more efficient use of the reactor volume are predicted with a burner having a distributor cone, than with a single-entry burner.

Jan 1, 1999

By G. K. Ruhlandt, C. W. Kim

"A 3-D Finite Element Method program called ""SOLCAST"" has been developed to simulate the casting solidification process. Using the temperature recovery method to evaluate the latent heat of fusion and applying a new combination of the time integration scheme, SOLCAST reduces the computational time significantly compared to an existing commercial FEM program, and produces accurate results comparable to experimental casting results. Prediction of casting shrinkage porosity for A390 aluminum alloy will also be discussed. To make this FEM program useful for foundry engineers, this program was connected to a commercial pre- and post-processor.IntroductionBecause of recently increased competition, foundrymen must produce high quality castings more economically. Therefore, casting solidification analysis prior to casting production is an attractive way to reduce costs and development time.Although the actual casting solidification process is a very complicated phenomena, foundrymen could predict where shrinkage defects would occur based on a transient conduction heat transfer analysis that includes the liberation of latent heat. A numerical analysis is generally required to solve the heat diffusion equation with the latent heat diffusion term, because casting shapes are very complicated and pure materials are rarely used.Different numerical methods have been applied to the casting solidification analysis 1. Among them, a finite difference method 2 and a finite element method (FEM)3 are most commonly used.Each simulation method has one or more basic difficulties which are different for each method. These difficulties are:(1) Modeling casting shapes on a computer.(2) Time consuming computation.(3) Uncertain material properties."

Jan 1, 1986

By W Zeng, D Walker, D Cai, E Baafi

"The efficiency of the truck-shovel haulage system is significantly influenced by the truck fleet size. A discrete event simulation model with 3D animation has been developed to estimate the productivity of a truck-shovel network system, shovel efficiency, truck cycle time, truck utilisation and the optimal fleet size. The simulation model considers the dynamic variability of traffic conditions and also the truck as an individual entity. The resulting truck cycle time was found to be realistic and thus providing a better tool for strategic mine planning.Citation:Zeng, W, Baafi, E, Walker, D and Cai, D, 2016. A 3D Discrete Event Simulation Model of a Truck-shovel Network System, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 265–273 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By B. I. Hop

The f10wfield set up by the standard Hydro gas purging unit has been predicted by a numerical model. In addition turbulent trajectories of gas bubbles released from the rotor are predicted. Here the deposition rate of inclusions on the bubble surface is allowed to depend on local conditions. Bubbles passing regions with strong pressure gradients, such as close to the rotor, will experience large slip velocities and large deposition rates. This model can deal with any distribution of bubble sizes and inclusions. The results found from the multidimensional flow predictions are discussed in relation to what can be obtained from a much simpler metallurgical engineering approach. The differences between these two approaches to predict the same process will be discussed. The model predictions are compared to experimental results for removal of SiC-particles from aluminium.

Jan 1, 1996

By E. Saez, M. Bellet, T. Coupez, O. Jaouen

"The paper presents a 3D finite element solver for non-steady state fluid flow. The thermomechanical simulation package REM3D® has been initially developed to model Stokes' flow for polymer injection. The mechanical module is based on a Eulerian velocitypressure formulation. The spatial discretization uses P 1+IP1 tetrahedral elements. The front tracking module consists of the resolution of a transport equation, thanks to a space-time discontinuous Galerkin formulation. It includes mesh adaptation, which permits a dynamic refinement at the front, thus controling the numerical diffusion. The same approach is used to solve heat transfer. In this paper, we focus on the specific adaptations done to treat Navier Stokes flow. The treatment of inertia is detailed, as well as the implementation of sliding conditions at mould surface, using conservative normals. Industrial applications are presented.IntroductionThe study of the mould filling stage in casting processes requires the ability to simulate complex non steady-state three-dimensional flows. Most commercial software use the volume of fluid (VOF) method, associated with a Eulerian formulation, see for instance the series of conferences ""Modelling of Casting, Welding and Advanced Solidification Processes"" [1-3]. The VOF method [4] consists in solving the conservation equation dF / dt = 0 for a variable F - the volumic fraction of fluid - whose value is 1 in filled regions and 0 elsewhere. Two fluids are actually considered: the molten alloy and a gas in the empty regions. This method suffers generally from numerical diffusion in the resolution of the free surface tracking equation, which is of pure advective type. The precision of the computation is then strongly dependent on the mesh density. Since the mesh is fixed (Eulerian formulation) this implies that in case of complex flow the user must have a priori a fairly good idea of the flow characteristics in order to capture properly the critical features of the flow. In addition, the method can hardly handle the discontinuity of the material viscosity at the interface. To prevent this difficulty, the viscosity value is smoothed around the interfuce, adding once again some inaccuracy. Since the value F = ½ is supposed to represent the free surface, it results in a smeared fluid surface. An alternative to the fixed mesh methods are the methods in which the mesh covers the fluid domain only, as proposed by Navti and Lewis [5-6], or Gaston and Bellet [7]. Based on updated Lagrangian schemes, they must be associated with an ALE formulation (arbitrary LagrangianEulerian) in order to reduce the number of full remeshing operations."

Jan 1, 2004

By Bruce Richardson

A contractor-manufactured 4.75m (15'-7") diameter EPB shield excavated a 115m (375 ft) long tunnel under the San Antonio River as part of the Salado Creek to Dos Rios Pipeline Interconnect Project in San Antonio, Texas. Lignite, limestone concretions, and sandstone in the face of the tunnel required the use of disc cutters. Less than 7.6m (25 ft) of sand and gravel hydraulically connected the top of the tunnel to the channel of the river. Fully lagged steel ribs with filter fabric were used for initial ground support and water control. This and other contractor manufactured TBMs in the 1.2 to 4.75m (4 to 16 ft) range are presented with descriptions of the jobsites, equipment, performances, and problems.

Jan 1, 2008

By Pedro Jorge Walburga Keglevich de Buzin

A presença de elementos residuais nas sucatas ferrosas pode influenciar a qualidade do aço produzido na aciaria elétrica. Além disto, o cloro existente nos materiais orgânicos que acompanham as sucatas leva a problemas de ordem ambiental. Por este motivo, o acompanhamento destes contaminantes através de métodos de amostragem de sucata se torna uma tarefa importante na aciaria elétrica. Neste trabalho são apresentados alguns procedimentos de amostragem de sucata, bem como uma análise comparativa de sucatas processadas por moinhos do tipo shredder e sucatas sem processamento. Os resultados mostraram um aumento da densidade e a redução do teor de contaminantes (matéria orgânica, alumínio e aço inox) para a sucata processada por shredder em comparação com a sucata sem processamento. Complementando, é apresentado um perfil da concentração de cloro em diversos materiais orgânicos comumentemente encontrados nas sucatas.

Oct 30, 2017

By Keith A. Heasley

The objective of this paper is to back-analyze the August 6th ,2007 collapse at the Crandall Canyon Mine in order to better understand the geometric and geo- mechanical factors which contributed to that collapse. In this work, the LaModel boundary-element program along with the best available information is used for the back- analysis. To initiate the analysis, a six step base model of the mining in he Main West area was developed. This base model included a step for each of the critical stages in the mining of this area. Next, calibrated values for the critical input parameters: rock mass stiffness, gob stiffness and coal strength, were developed and optimized based on the best available information. Finally, the model was used to simulate the final mining scenario. As a result of this back analysis , a number of conclusions can be made concerning the mine design and the August 6th collapse: 1) Overall, the area was primed for a massive pillar collapse because of the large area of equal size pillars, 2) The abutment stress from the active retreat sections and the adjacent longwall panels were significant contributors to the collapse, 3) From the modeling alone, it is not clear exactly what triggered the August collapse, although the active mining is a reasonable assumption.

Jan 1, 2012

By K. A. Heasley

The objective of this paper is to back analyze the August 6th, 2007, collapse at the Crandall Canyon Mine in Utah, in order to better understand the geometric and geomechanical factors that contributed to that collapse. In this work, the LaModel boundary-element program, along with the best available information, is used for the back analysis. To initiate the analysis, a six-step base model of the mining in the Main West area was developed. This base model included a step for each of the critical stages in the mining of this area. Next, calibrated values for the critical input parameters, rock mass stiffness, gob stiffness and coal strength, were developed and optimized based on the best available information. Finally, the model was used to simulate the final mining scenario. As a result of this back analysis, a number of conclusions can be made concerning the mine design and the August 6th collapse: 1) overall, the area was primed for a massive pillar collapse because of the large area of equal-size pillars, 2) the abutment stress from the active retreat sections and the adjacent longwall panels were significant contributors to the collapse and 3) from the modeling alone, it is not clear exactly what triggered the August collapse, although the active mining is a reasonable assumption.

Jan 1, 2010

By Noel Stearn

WHEN the Age of Machinery was suddenly thrust upon civilization about the beginning of the nineteenth century, an unprecedented demand for mineral resources sprang up. This demand brought about the rapid development of the known ore deposits and the discovery of such other deposits as could be encountered by energetic and canny pros-pectors. Thus in the countries now reasonably ac-cessible nearly all orebodies have been located except those which are totally concealed even from the eyes and "senses" of experienced and expert prospectors. The high rate of exhaustion of known ore deposits and the necessity of looking farther and farther ahead for raw materials as a matter of insurance on the stu-pendous capital outlays involved in mining, develop-ment, and conversion operations, have resulted in excep-tional activity in three different fields of effort. The first is purely geographic. Prospectors are now pene-trating the few hitherto inaccessible regions in the hope of stumbling upon exposed ore deposits or locating visible indications of their presence. The second is chemical. Industrial chemists and metallurgists are seeking to facilitate the exploitation of lower grade ores to find methods of recovering valuable metals from common substances. In the third field of effort. lie the activities of the economic geologist and the mining engineer, who en-deavor to locate concealed ore deposits, which would remain hidden from the prospector, no matter. how expert or conscientious he might be. Obviously the task which such a man must face is both exacting and indefinite, and the tools which he has heretofore been permitted to bring to it are, for the most part, abstract-a knowledge of certain fundamental princi-ples and processes involved in the origin, occurrence, structure, and distribution of deposits. of natural re-sources and of the rocks which form the environments of those deposits, and a process-of reasoning by analogy supplemented by the .use of the diamond drill, or such artificial exposure as the test pit, trench, shaft or tunnel. His primary efforts are usually bent on acquiring a knowledge of the distribution of the rocks-as accurate -is possible-which is a natural prerequisite to any conclusion as to how they became so distributed. Over very extensive areas, however, he meets. the extreme difficulty of being unable to see the rocks, except at rare intervals, since .they have been concealed by an overburden of glacial material, of alluvium, of soil, or of other rocks.

Jan 9, 1928

By S W. Robertson, A Vercuil, P Craven

Mintek is currently developing a design approach for the heap leaching of low-grade primary copper sulphide material. Since the leaching of chalcopyrite requires elevated temperatures, the generation and management of heat within the heap is crucial. Furthermore, the precipitation of iron needs to be managed to prevent premature blinding of the heap, and acid consumption needs to be limited to contain cost and limit the dissolution of gangue impurities. Standard column tests using jacketed 1-m and/or 6-m columns do not allow accurate prediction of temperature changes and heat generation in an actual heap. Mintek therefore utilizes a computer model to calculate the energy balance and heat generation with time, based on the measured sulphide oxidation rates in the column. The temperature in the column is then adjusted to reflect the computer-predicted temperature in an actual heap. Using this approach, an overall copper extraction of 70% was achieved in 120 days, using 1-metre columns, when treating an ore blend containing 1.36% chalcopyrite, 0.23% chalcocite, 0.07% covellite, 3.8% pyrite and silicate gangue (92%). The chalcopyrite contribution to the total copper content in the feed was 75%. This was followed by 6-m columns using a similar approach, and the column results will be validated on a 23,000 tonne test heap. Key Words: heap; bioleach; chalcopyrite

Jan 1, 2005

Banks' focus in using cash flow methods can differ markedly from that of equity investors. This paper attempts to explain and describe bankers' approach by: ò outlining the fundamental difference between banks' and investors' risk / return profiles. ò describing lenders' consequent use of cash flow methods in mineral valuation. areas. explaining lenders' specific treatment of key risk Fundamental to understanding banks' appraisal of mineral projects is the appreciation that lenders have a basically different risk profile and outlook from those familiar to equity investors. Lenders do not normally participate in any project upside. The economics of lending dictate that banks can only accommodate a low probability of loan default and consequently banks' principal focus in mineral ""valuation"" is ensuring an acceptably comfortable probability of debt repayment. A simple conceptual explanation of lenders' risk / return position is outlined.

Jan 1, 1994