Search Documents

By Carl E. Swartz

Although a number of articles appeared during the war advocating the use of cadmium in lead-tin solders, very little information of value can be found in the literature regarding the properties of solders containing cadmium. In most of the published articles the cadmium seems to have been considered merely as a partial substitute for tin in a tin-lead alloy rather than as an essential constituent of a ternary alloy. The primary object of the substitution of cadmium for tin was to lessen the amount of tin required, at a time when the latter was scarce and high-priced, and thus to produce a cheaper solder. While this object was accomplished, the new properties resulting from a change from a binary lead-tin alloy to a ternary lead-tin-cadmium alloy were not given proper consideration in many cases. For the past few years, the American Smelting & Refining Co. has been marketing a very considerable amount of cadmium in the form of lead-tin-cadmium alloys for use as solders for certain special purposes, and the successful use of these solders suggested that if more extensive knowledge were available concerning the properties of lead-tin-cadmium alloys of various compositions their field of usefulness might be materially extended. The investigation described in the present paper was undertaken to obtain this information and, by means of tests under conditions approaching those of practical use, to determine the suitability of cadmium solders for various purposes. Characteristics and Requirements of Solders in General General Physical Properties.—When cast into bars, solder should present a smooth and bright appearance free from oxide inclusions and bubbles. Ductility should be as great as possible without sacrificing tensile strength, and vice versa. Hardness and specific gravity are not of any great importance. Melting Characteristics.—The melting or solidification range is important. This statement applies both to the extent of the range and to the actual temperature at which complete solidification occurs. A rather narrow solidification range is desirable in soft solders in order that solidification may take place quickly. The solder should have high fluidity at temperatures only slightly above its melting range. For a

By J. Spotts McDowell

Ackowledgments........................... 5 Introduction............................. 5 The Silica Minerals. Stability Relations......................... 6 Optical Properties........................ 9 Density.............................. 10 Melting Points....;..................... 10 Thermal Expansion..................,..... 10 Solubilities............................ 12 Identification of Cristobalite and Tridymite.............. 12. The Silica Refractories. Raw Materia1........................... 13 American Deposits....................... 13 Properties Determining Usability................ 15 Expansion on Heating..................... 16 Texture........................... 17 Silica Brick............................ 17 Manufacture........................... 18 Properties of Silica Brick .................... 19 Analysis ......................... 19 Density......................... 19 Porosity......................... 20 Strength....................... 21 Melting Point....................... 22 Specific Heat....................... 22 Thermal Conductivity................... 23 Expansion........................ 24 Effect of Rapid Temperature Change.........:... 26 Constitution......................... 26

Jan 1, 1918

By J. H. Nead

The subject of this paper is one to which there are many references in the literature on the manufacture of steel in the open-hearth furnace, but few actual experimental data have been published. For that reason, the presentation of results obtained from two open-hearth heats where attempts were made to measure the sulfur absorption will be of considerable interest and value. The two heats on which the experiments were made were Armco ingot-iron heats and differ from the usual open-hearth heat of medium- or mild-carbon steel in that the refining is carried further; in this product the carbon and manganese are reduced practically to traces. In most other respects, and especially in respect to the absorption of sulfur from the producer gas, the two heats are typical of usual open-hearth practice. The object of the experiments made on the first Armco iron heat was to determine the fluctuation of the composition of the metal bath and the slag throughout the course of the heat, with especial reference to the variations in sulfur. It was hoped to determine whether there was an increase in sulfur in the bath from the producer gas and if so at what stage in the process the increase occurred. The experimental method consisted of charging analyzed scrap and pig iron, so that the sulfur in the charge could be calculated. Then, throughout the duration of the heat, metal and slag samples were takcn every half hour, beginning as soon as there was enough molten metal to take a sample. These samples were analyzed; the results are given in Table 1. All domestic scrap was used and the charge was made up as follows: Head End Finish Pounds Pound Pig iron........................ 36,300 Pig iron....................... 23,900 Sheet scrap bundles............. 36,200 Sheet bars..................... 23,900 Sheet bm..................... 40;200 The total charge, exclusive of the re-pig added near the end of the heat, was 160,500 Ib. The limestone charged was 21,400 Ib., or 13½ per cent.

Jan 1, 1924

By Henry M. Howe, W. P. Barba

When this country went into the war, but two concerns, The Bethlehem Steel Co. and The Midvale Steel and Ordnance Co., knew how to make steel fit for great cannons and at these concerns there were relatively few men who knew the whole art. Fortunately, certain of these men put their knowledge at the service of the Government, and proceeded to instruct the metallurgists at the arsenals and at various steel works. Doctor Howe, then chairman of the Engineering Division of the National Research Council, suggested that this work might be facilitated, and the number of effective gun-steel makers thereby increased, if a detailed description of the best practice could be written, giving the reasons for the various steps, and issued with the endorsement of a committee composed of those who were evidently the most competent authorities. It was thought that something would be gained by clarification of the subject, and something by the eminent authority of the members of the committee. To that end, the Engineering Division appointed a committee, consisting of the gentlemen whose names follow, to mention on1y those who retained their connection with it. At this time there were serious difficulties in the manufacture, for the Government. of aircraft and high-speed engine crankshafts, of certain ordnance forgings, and of shells for both the Army and Navy. This Committee was asked to study and report upon these, with a view to betterment of practice. There were indications that the source of some of the difficulties went back to the melting of the steel and the production of the ingot. Hence, the committee first studied steel melting and ingot production, in order to guide the wartime manufacturers to an even larger percentage of useful production from the steel initially melted. Committee on Steel Ingots W. P. Barba, chairman, Ordnance Dept., U. S. A. (formerly Vice Pres. & Gen. Mgr., Midvale Steel Co., Philadelphia). George K. Burgess, Chief of Division of Metallurgy, U. S. Bureau of Standards, Washington, D. C. Henry M. Howe, Then Chairman Engineering Division, National Research Council.

Jan 1, 1922

By W. P. Barba, Henry M. Howe

When this country went into the war, but two concerns, The Bethlehem Steel Co. and The Midvale Steel and Ordnance Co., knew how to make steel fit for great cannons and at these concerns there were relatively few men who knew the whole art. Fortunately, certain of these men put their knowledge at the service of the Government, and proceeded to instruct the metallurgists at the arsenals and at various steel works. Doctor Howe, then chairman of the Engineering Division of the National Research Council, suggested that this work might be facilitated, and the number of effective gun-steel makers thereby increased, if a detailed description of the best practice could be written, giving the reasons for the various steps, and issued with the endorsement of a committee composed of those who were evidently the most competent authorities. It was thought that something would be gained by clarification of the subject, and something by the eminent authority of the members of the committee. To that end, the Engineering Division appointed a committee, consisting of the gentlemen whose names follow, to mention on1y those who retained their connection with it. At this time there were serious difficulties in the manufacture, for the Government. of aircraft and high-speed engine crankshafts, of certain ordnance forgings, and of shells for both the Army and Navy. This Committee was asked to study and report upon these, with a view to betterment of practice. There were indications that the source of some of the difficulties went back to the melting of the steel and the production of the ingot. Hence, the committee first studied steel melting and ingot production, in order to guide the wartime manufacturers to an even larger percentage of useful production from the steel initially melted. Committee on Steel Ingots W. P. Barba, chairman, Ordnance Dept., U. S. A. (formerly Vice Pres. & Gen. Mgr., Midvale Steel Co., Philadelphia). George K. Burgess, Chief of Division of Metallurgy, U. S. Bureau of Standards, Washington, D. C. Henry M. Howe, Then Chairman Engineering Division, National Research Council.

Jan 1, 1922

By Carls Benedicks

It is well known by every one who has had to deal with boiler tubes that these are often seriously affected by a sort of corrosion, occurring as a local pitting, that frequently causes a perforation of the tube in a rather short time. The characteristic appearance of this corrosion is shown in Fig. 1. A very similar corrosion occurs in condenser tubes (Fig. 2).l A study of the microstructure or local chemical composition of the metal (iron 70:30 brass) fails to reveal any cause for this pitting. Of course one might possibly assume the starting point to be some oxide particle, causing an electrolytic local action, but this in no way explains the continued corrosion, progressing even when the assumed oxide particle must have disappeared. By the excellent work done by the Corrosion Research Committee of the Institute of Metals, and communicated, in October, 1923, to the Institution of Engineers and Shipbuilders in Newcastle-on-tyne, stress was laid on the faot that a content of entangled air has a very obnoxious effect. In the following correspondence, Sir George Goodwin stated that "engineers have, for a long time past, regarded air as the big enemy to be fought against in all questions of corrosion'72 and Kenneth Fraser pointed out that the most vital point is "the avoidance or removal of possibly the chief cause of present day corrosion, i. e. entrapped air and gases brought out of solution."3 In their reply, however, the authors state that they had "never for a moment believed that entangled air was responsible for the beginnings of corrosion, and express the opinion that the gradual liberation of air could not account for localized corro~ion."~ On consulting the many textbooks on corrosion, as that

Jan 1, 1925

By Henry M. Howe

COLUMBIA UNIVERSITY The Equilibrium Position of A 1.—Some of the most important data on this subject are collected in Table I. Definition of Ae 1.—-Just as we call A 1 of rising temperature Ac 1, and that of falling temperature Ar 1, so we may give the symbol Ae 1 to the equilibrium position of A 1. Preliminary Assumptions.—In deciding what weight to assign the various data, and indeed what data are to count, three assumptions should be made. These are : 1. The corollary from the phase rule, that the temperature of Ae 1 is constant and independent of the carbon content, though, of course, it may be changed by the presence of other elements. 2. That because neither in heating nor in cooling can the transformatioil begin before the temperature reaches Ae 1, though it may be delayed by lag till after the temperature has passed beyond Ae 1, therefore Ae 1 should be at or below the observed beginning of Ac 1 and at or above the observed beginning of Ar 1, and, a fortiori, it should be at or below the observed maximum of Ac 1, and at or above the observed maximum of Ar 1. It may be necessary to take these maxima into consideration in view of the experimental difficulty of detecting these beginnings. 3. Because of the extraordinary degree of lag in the immediate neighborhood of Ae 1, as proved by Brayshaw, little weight should be attached even to the most conclusive evidence that the transformation has not occurred on reaching, or even staying at, a given temperature, because that failure to occur may always be due to lag. Evidence that the transformation has occurred, or has even begun, at a given temperature deserves incomparably greater weight. In other words, the temperature may pass beyond Ae 1 without inducing the ' transformation, but the transformation cannot be induced except by

Jan 1, 1914

By H. Foster Bain

[Secretary's NoTE.—This paper, presented in oral abstract at the San Francisco meeting, was not at first supposed by Mr. Rain to be required for publication in the Transactions; and the excursion to Japan, in which he took part, immediately after the San Francisco meeting, delayed his presentation of the manuscript. After his return to San Francisco, Mr. Bain, in view of the importance of his paper and its discussion, kindly furnished it in full. The delay in its publication (since it was received in April last) has been due, partly to the circumstance that other contributions had meanwhile acquired the " right of way," and partly to the consideration that, the situation contemplated in Mr. Bain's paper having remained practically unchanged, the paper and its discussion would not lose force or timeliness by this lapse of time.—J. S. ] No acute observer of public affairs can have failed to observe a growing disposition on the part of the public to change emphasis in government from political equality to social justice. When our own government was founded it was felt to be sufficient to secure to each individual the fullest possible freedom of opportunity, and such a scheme was excellently adapted to the rapid development of a large territory having a small population. As the number of people in a given area increases, there are more points of contact and conflict; each must move in a smaller orbit, and there must be more regula-

Jan 1, 1913

By A. J. Phillips, C. G. Grant, Wm. B. Price

Admiralty nickel is a new corrosion-resisting and heat-resisting white metal alloy composed of 70 per cent. copper, 29 per cent. nickel and 1 per cent. tin. It has been given the trade name "Adnic." In 1924, Wm. B. Price' described this alloy and its successful use as a diaphragm metal. The physical properties of Adnic at ordinary and elevated temperatures were given in Mining & Metallury.~ A patent3 was granted on Adnic, April 28, 1925. Work was first started on this alloy during December, 1921. An investigation of the patent situation in this country and abroad, and also a search of the literature, did not reveal any work on the ternary diagram, copper-nickel-tin; and the only wrought copper-nickel-tin alloy found was that known as "Newloy," composed of copper, 64 per cent.; nickel, 35 per cent.; tin, 1 per cent. This was being manufactured and sold by Wm. Gallimorr & Sons, Ltd., Sheffield, England, for unplated spoon and fork stock, and first came to our attention in January, 1922. The preliminary work in connection with the development of Adnic was started by casting four binary copper-nickel alloys of the compositions shown in Table 1. Various a~ilounts of tin were added to each of these mixtures, to produce the series of ternary copper-nickel-tin alloys also given in Table 1. A 200-gm. sample of each of these was cast by iiielting in a clay graphite crucible and allowing the melt to slowly cool with the furnace. A longitudinal section from each of thcsc castings was polished and etched for examination. The castings were not homogenrous solid solutions, but showed the usual cored structure associated with cast alloys. Howcvrr, frorn an exarrlination of these sections we roughly determined

By W. L. Fink, R. S. Archer

This paper describes results obtained on aluminum-beryllium alloys and aluminum-beryllium-copper alloys in the preparation of which aluminum of 99.95 per cent. purity was used. The constitution and structure of the high purity binary alloys are given. The aluminum-beryllium eutectic occurs at 0.87 per cent. beryllium and 645° C. The solid solubility of beryllium in aluminum at 631° C. is 0.05 per cent, beryllium, and at room temperature is less than 0.013 per cent. beryllium. The densities of the alloys are substantially the same as the values calculated on the assumption that the densities of the elements are not changed by alloying. All of the alloys age-harden at room temperature after a solution heat treatment, and the chill cast aluminum-beryllium-copper alloys age-harden at room temperature without a prior solution heat treatment. Hardness and tensile properties are given. Salt spray corrosion tests on sheet specimens are described. It is shown that beryllium docs not lower the corrosion resistance of aluminum to salt spray provided the alloy has received a solution heat treatment. Commercial Possibilities of Beryllium Alloys Beryllium has certain properties such as low density, high hardness, good corrosion resistance, low thermal expansion and fairly good electrical conductivity, which would indicate that it is worthy of consideration as an ingredient of light alloys. It was not until recently, however, that beryllium could be produced with sufficient ease to encourage research along this line. The production of beryllium by electrolysis from a fluoride bath has now developed to the stage where it could be used commercially if there were sufficient demand for the element. Claims made in certain newspapers and technical articles in regard to thc strength and corrosion resistance of thc aluminum-beryllium alloys are not justified by experimental results. Moreover, beryllium is an expensive metal ($200 a pound at the time this work was done) and, on account of the nature of its ore and the consequent difficulty of its extraction, it will in all probability continue to be a relatively expensive metal, although the cost would undoubtedly be a great deal less than $200 a

By Frank Firmstone

. In the early decades of the past century the method of starting iron blast-furnaces by " scatlolding-down" seems to have been in universal use for coke-furnaces and, at least in this country, for charcoal-furnaces also. It was likewise used at some of the early anthracite-furnaces, as is stated in the important " Reminiscences" printed by the late Samuel Thomas.' It had been generally superseded in Great Britain as early as 1850, by some variations of the plan now used, and was rarely used when Percy wrote.2 On the Continent it was still followed ill the 60's; and was elaborately described by Valerius in 1852. I have never read any statement as to when and by whom " scaffolding " was first dispensed with, but the following extracts from journals of my father seem to fix an authentic date for an instance in this country: " [Pittsburg] July 12, 1838.—Went with Major Wade to his foundry,etc., and he gave me a letter to D. Tyler, Esq., Farrandsville, Agent Boston Coke & Iron Co." " [Lockhaven, Pa.] July 18, 1838.—Heard there was a flat-boat going to take some gentlemen up to Farrandsville. Got on boat and to Farrandsville, 5 or 6 miles, in 1 hr. 30 min. Dined, and then delivered my letter to Ma Tyler, who showed me much attention, and everything belonging to the furnace, and had the water turned on the wheel that I might see the blowing-cylinders at work. There are two cylinders, 6-ft. stroke, -56 in. in diameter, but they find that one makes more than enough blast for the furnace. The furnace has 16-ft. boshes, 7-ft. tunnel-head, and is 47 ft. high, 3 tuyeres, and 3 heating-ovens [hot blast-ovens]. A

Jan 1, 1908

By Frank H. Armstrong

All the mining machinery of the Penn Iron Mining Co. has been operated by electric power for several years and when another shovel for stockpile loading was required the advantages of an electric shovel were naturally considered. After considerable study, serious objections suggested themselves the use of a shovel operated directly by electrical apparatus by reason of the complicated control, severe service on the motors and the heavy surges of current required from the line. It was finally decided to construct an electro-hydraulic shovel using water under pressure to perform all the necessary operations except that of propelling, for which a separate motor was best suited. A car body with boom, dipper handle and dipper of late design, but without any of the steam machinery, was purchased. A motor-driven centrifugal pump, a pressure tank, an air tank, a small air compressor and water cylinders with plungers, pistons and valves, were installed in place of the steam equipment. Fig. 1 shows this shovel under construction and Fig. 2 shows it as it was operated during the first year, the summer of 1914. The large tank at the back of the car, in Fig. 1, carried air under

Jan 1, 1916

By P. W. Bridgman

During the war, the Navy undertook the construction, under my direction, of an experimental gun embodying features designed to lessen the cost and time of production. These experiments were initiated after representations as to their desirability had been offered by myself, by the Naval Consulting Board, and by the National Research Council. The first drawings were made in June, 1917, and the experiment was completed in November, 1918. For the sake of clearness it will pay to recapitulate briefly the fundamental idea of gun construction. It is well known that if a hollow cylinder is subjected to internal fluid pressure, the maximum stress occurs in the inside layers, the outer parts carrying much less than their due share of the stress. This inequality of stress is more pronounced the thicker the walls of the cylinder. If such a cylinder is pushed to the elastic limit, failure in elasticity will take place long before the outer lagers have reached the limit of their capacity. Economical use of the material would demand, however, that all parts of the cylinder reach the limits of their capacity simultaneously. This may be brought about, at least in cylinders of not too great thickness, by producing in the inner layers an initial compression, and in the outer layers an initial tension. The effect of internal pressure is at first to relieve the compression of the inside layers, while increasing the tension of the outside layers. If the initial stresses are properly distributed, all parts of the cylinder will reach their elastic limits simultaneously, thus giving a cylinder of maximum strength for its weight. In gun construction as hitherto practiced, this initial distribution of stress is produced either by winding the inner tube with wire, a common English practice, or by shrinking hoops over the inner tube, which has been the standard American practice. Either process is long and expensive, particularly with the larger guns, 12- or 14-in., which require

Jan 1, 1922

By P. W. Bridgman

During the war, the Navy undertook the construction, under my direction, of an experimental gun embodying features designed to lessen the cost and time of production. These experiments were initiated after representations as to their desirability had been offered by myself, by the Naval Consulting Board, and by the National Research Council. The first drawings were made in June, 1917, and the experiment was completed in November, 1918. For the sake of clearness it will pay to recapitulate briefly the fundamental idea of gun construction. It is well known that if a hollow cylinder is subjected to internal fluid pressure, the maximum stress occurs in the inside layers, the outer parts carrying much less than their due share of the stress. This inequality of stress is more pronounced the thicker the walls of the cylinder. If such a cylinder is pushed to the elastic limit, failure in elasticity will take place long before the outer lagers have reached the limit of their capacity. Economical use of the material would demand, however, that all parts of the cylinder reach the limits of their capacity simultaneously. This may be brought about, at least in cylinders of not too great thickness, by producing in the inner layers an initial compression, and in the outer layers an initial tension. The effect of internal pressure is at first to relieve the compression of the inside layers, while increasing the tension of the outside layers. If the initial stresses are properly distributed, all parts of the cylinder will reach their elastic limits simultaneously, thus giving a cylinder of maximum strength for its weight. In gun construction as hitherto practiced, this initial distribution of stress is produced either by winding the inner tube with wire, a common English practice, or by shrinking hoops over the inner tube, which has been the standard American practice. Either process is long and expensive, particularly with the larger guns, 12- or 14-in., which require

Jan 1, 1922

By C. A. Allen

For over three years we have been endeavoring to reduce the number of fatalitics and minor accidents in Utah. The physical condition of the FIG: 1.—Number kiLlEd per million short tons of coal produced in ColoraI)o, New Mexico, utah, Wyoming, and bituminous mines of the United States 1014 to 1920. mines, concentrators, and smelters is good, yet the number of accidents,

Jan 1, 1923

By C. A. Allen

For over three years we have been endeavoring to reduce the number of fatalitics and minor accidents in Utah. The physical condition of the FIG: 1.—Number kiLlEd per million short tons of coal produced in ColoraI)o, New Mexico, utah, Wyoming, and bituminous mines of the United States 1014 to 1920. mines, concentrators, and smelters is good, yet the number of accidents,

Jan 1, 1923

By Thomas Egleston

All industrial establishments whose operations depend upon chemical reactions use gases. In the simplest case the oxygen of the atmosphere, heated or not, as the case may be, is used, and in other cases, gases which are produced by a special apparatus of more or less complex composition. The manufacturer depends, for the success of his operations, entirely upon having these gases arrive at the right time, in the proper proportions, at the required temperature. It often requires but a slight variation in their composition to make a given process a success or a failure. In most cases the gas used is formed from fuel, and according as variations in its composition are produced by alterations in the manner of charging the grate, not only different, but often directly opposite, results are obtained. The great industrial question of the present time, and one upon which the prosperity of the world depends, is how to get the greatest amount of useful effect from fuel, whether the caloric is used directly or is transformed into horse-power. In almost all industrial pursuits this translates itself into the question of how to construct a fireplace and its adjuncts in such a way that the heat of the flame and of the products of combustion shall be made to produce a maximum effect. Unfortunately, until very recently, except by comparison, there was no means of ascertaining whether the loss of useful effect was 80, 40, or 20 per cent. of the total amount of fuel employed. It seems now strange that there should have been furnaces so constructed as to produce 20 per cent. of carbonic acid in the fireplace, but this has been proved by analysis to have been true. It does seem incredible that, notwithstanding the immense number and variety of furnaces used for different processes, and the great difference in kind, quality, and quantity of fuels consumed, there should formerly have been used for them all, the same stereotyped fireplace, varied only in its dimensions of height, length, and breadth. It is true that, with a good fireman, excellent effects may be, and have been, produced, but the manufacture is here, as in many other cases, dependent on the intelligence of the workman, a very uncertain reliance for capital to rest upon. The workman, unless he receives a prime for fuel saved, or is fined for excessive use of it, may be said

By Thomas Fraser, H. F. Yancey

The jig may be termed the standard coal-washing machine. Although exact figures on the relative tonnages of coal treated by the various coal-cleaning processes are not available, it is known that a large part of all the coal given special cleaning treatment is handled by jigs. This wide use of the jig warrants a special study of its performance. In this paper are presented the results of an analysis of work done by a three-compartment jig in treating bituminous coal from the Thick Freeport bed in Allegheny County, Pa. Certain systems of washing coal require sizing before washing, while others treat unsized coal. The prevailing practice, however, for the preparation of coking coal from the more easily washed coal is to treat an unsized or natural feed of about — 1 in. size and smaller. Under such conditions, the minimum size of particle that is beneficiated has long been and is still a matter of discussion and conjecture. In a careful laboratory investigation J?ngstl concluded that the practical limit of settling of fine coal is reached at from 0.02 to 0.008 in. On the other hand, Hancock2 has found that single-compartment jigs, used in preparing coal for the domestic market, usually allow most of the heavy (refuse) particles smaller than 1/4 in. to go into the washed coal. He also states that it is impossible with the ordinary coal jig to make any noticeable improvement in the quality of the coal finer than 20 mesh (about 1/30 in.). Because of its importance in coal cleaning, the work described in this paper was undertaken for the purpose of obtaining information on this subject, as a part of the general coal beneficiation program being carried out by the Bureau of Mines.

Jan 1, 1925

By F. B. Foley

With the possible exception of high-speed tool steel, the service demanded of rock-drill steel is probably more precarious than that of any other tool steel. Unaided by the helpful influence of alloys and dependent solely on the efficiency of the heat treatment applied for its ability to stand up under the abuse to which it is necessarily subjected, rock-drill steel is worthy of intensive study. For its heat treatment the smith has his fire, an oil fire perhaps, and a quenching bath; he judges the temperature by his eye. There are shops where excellent drills are produced by this method, but there are more where the product varies between very good and very bad. Pyrometers with specially designed equipment are used in but few cases. But the responsibility for rock-drill failures does not rest entirely on the smith. Little has been published concerning the efficiency of drill steel, though the Canadian Mining Journal1 published the breakage record of a large number of hollow drill steels. This record indicates that most of the breaks occur during the early life of the steel and that as a given batch of steel is used, its percentage of breakage decreases. This fact, the article points out, is at variance with the much-talked-of theory concerning failure from crystallization and fatigue. It seems to point to the fact that the greater part of drill-steel failure from breakage is traceable to faulty manufacture, resulting in defects in the bore of the hollow steel from inclusions of slag or oxides, etc. As this defective material meets with early failure, it is weeded out. In addition, some breakage may be caused by a lack of proper condition with respect to heat treatment of the steel as furnished by the manufacturer. In the article mentioned, the breakage of 1/14-in (3.17 cm.) hollow steel is given as 4.62 per cent. for the early period of use, with a decrease to 3.35 per cent. and 2.67 per cent. with time in use. For 1-in. (2.5 cm.) hexagonal hollow steel, the figures for breakage are 0.18 per cent. and 0.06 per cent.; attention is called to the great decrease in breakage by the use of smaller diameter drills. The figures are given as so many drills sharpened, but there is no way of determining the percentage of

Jan 1, 1922

By R. V. Norris

It was stated in a former paper1 that an intensive study of anthracite costs was being made by the engineers of the United States Fuel Administration. The results of this study are now available and are offered as a supplement to the former paper. Anthracite costs as reported for the 6-months period, December, 1917, to May, 1918, inclusive, as compiled by the Federal Trade Commission, were used as a base, and charts similar to those described in the former paper were made for the standard white ash anthracite and for red ash and Lykens valley coals. Adjustments The adjustments of cost from a reported to a price-fixing basis, as described for the bituminous methods, were applied but showed only minor adjustments as necessary. The great spread in anthracite prices on the varyingsizes, which for the 6-mo. period under review ranged in average from $5.244 for nut to $2.074 for barley coal, makes the question of the percentage of sizes produced at the different collieries a vital one. The realization with the same prices for each size must be within very wide limits, when it is considered that the percentage of prepared coal reported from different collieries varied from over 80 per cent. to below 30 per cent. for fresh-mined coal. Hence, as the spread in prices for the various sizes must be predicated on some percentage, it is essential to find some method of adjustment to allow for this variation. The logical method of adjustment is to calculate actual costs to costs as of the standard percentage of sizes, so that the margin between the adjusted costs and the average realization shall be the actual margin for each colliery between its actual costs and actual realization due to its particular percentage of sizes. As a base for realization the actual percentage of sizes for fresh-mined coal for the 6-mo. period was adopted. This percentage is given in Table 1.

Jan 1, 1920