Search Documents

By K Heiskanen, R A. Grau

Gas velocity (Jg) measurements conducted close to the froth-pulp interface over the cross-section of a flotation cell reveal how efficiently the incoming air is being dispersed throughout the volume of the cell. Furthermore, measurements of Jg at deepest locations in the cell provide valuable information about air recirculation and dispersion conditions in the bulk volume of the cell. Gas velocity in flotation cells has predominantly been measured by a transient capture of gas in a graduated probe. In this project, a new sensor for measuring gas velocity in an on-line manner was developed. A probe is partially immersed in the flotation machine, below the froth-liquid interface. The probe is used to collect the rising air bubbles from the liquid phase. The liquid-froth interface is shifted into the probe under vacuum. A controlled vacuum is kept inside the probe. As air bubbles burst inside the probe, the excess of air is continuously removed from the probe via suction. The removed air is measured using a mass flow meter. The fully automated sensor allows us to continuously measure Jg at different location in a flotation machine. An experimental programme was carried out in a 10 cm diameter laboratory flotation column to determine the accuracy and repeatability of the automated sensor. The new sensor was used for evaluating gas dispersion conditions in a 215 litre transparent laboratory scale flotation cell. Gas velocity distributions along the radial and axial directions of the cell were measured over a wide range of operating conditions. The operating conditions in the cell were modified by altering impeller speed and air flow rate. Two different rotor-stator mechanisms were utilised to disperse the air in the cell, the MultiMix and the FreeFlow mechanism. In this paper, a description of the gas velocity sensor is given, and the results of the experimental work are discussed in detail.

Jan 1, 2005

By Blair R. Benner

This paper describes the installation and operation of a Texas Nuclear on-line silica analyzer (NOLA) coupled with a Leeds and Northrup Microtrac particle-size monitor (Microtrac) at U.S. Steel's Minntac taconite concentrator. An automatic sampling system provides the NOLA with samples of final concentrate. After the sample is analyzed for silica by the NOLA, it is pumped to the Microtrac for size and surface area measurement. A sample is analyzed every six minutes, providing the control room with the silica concentration, the percent passing 270, 400, and 500 mesh, and an equivalent Blaine surface area number. When fed a slurry of final concentrate containing between 20 and 70% solids and 5 to 6% silica, the NOLA analysis is within ±0.2% of the wet chemistry silica. The agreement between the Microtrac output and standard screen analyses is ±1.2% at 270 mesh; ±1.5% at 400 mesh, and ±2% at 500 mesh. The poorer disagreement at the finer sizes is mainly due to inaccuracies in screening at 400 and 500 mesh. The agreement between Microtrac surface area a d laboratory Blaine surface area is about 9 ±80 cm 2/g. These instruments provide rapid and reliable feedback information to the concentrator and feed forward information to the agglomerator.

Jan 1, 1984

By Peter J. Coghill, Michael J. Millen, Brian D. Sowerby, Kirby D. Cunningham

"CSIRO Minerals has developed an integrated particle size analysis system for deployment in the grinding circuits of minerals processing plants. The system includes a slurry sampling station, a de-aeration tank and an ultrasonic particle size analyser (UltraPS). The UltraPS analyser is based on ultrasonic attenuation and velocity spectrometry combined with gamma-ray transmission. The technology is applicable to the measurement of 0.1 to 1000 µm diameter particles directly in highly concentrated slurries without dilution. The analyser incorporates a gamma-ray transmission gauge utilising an ultra-low activity radioisotope source that is exempt from International Atomic Energy Agency (IAEA) and Australian licensing regulations.The UltraPS analyser consists of a submersible probe and an electronics package. The probe can be immersed directly in a minerals processing plant stream if the aeration level in the stream is low. For applications where a de-aerated slurry stream is not available, CSIRO has developed an integrated system that includes a sampling station, a de-aeration tank as well as the UltraPS analyser itself. A schematic drawing of the continuous flow gravity fed system is shown in the figure. A commercial sampling system is used to supply slurry at a rate of 2.5m3/hr to the deaeration tank. The aim of the de-aeration tank is to remove air in the slurry to a level where meaningful particle size measurements can be performed. The tank volume is about 0.2m3, thus giving the slurry flowing through the tank a mean residence time in the tank of approximately five minutes. Tests at a number of concentrators have shown that five minutes is sufficient time for slurry to de-aerate to a level where ultrasonic measurements can be made. The tank incorporates an ultrasonic level detection sensor and flow to the deaeration tank is adjusted based on the level of slurry within the tank. The UltraPS probe is mounted through a flanged section of duct, which is bolted to the bottom of the de-aeration tank."

Jan 1, 2003

By H. N. Frock

The use of low-angle forward light scattering for measurement of particle size distribution has been described previously.1 Laboratory instrumentation using this technology is used routinely in operating plants for quality control and production control.2,3 Extension of the technique to on-line process monitoring and control has also been undertaken in several important areas. This paper will discuss the application of MICROTRAC R systems to the monitoring of particle size in wet slurry processes and dry powder grinding circuits. Examples of existing installations will be given with emphasis on performance and on-line reliability.

Jan 1, 1979

By Fuzail Siddiqui

"The SIDMIN program aims at filling the mineral processor’s need to know the deportment of ‘minerals of interest’ not just ‘elements of interest’ that pass through the processing plants. Generally, chemistry is used as a tool of routine monitoring on site. Mineralogy, which is relatively much slower, is used more as a tool of research and post mortem investigations and these services are usually provided by a distant facility. The SIDMIN program enables site management to receive chemical and quantitative mineralogical reports on their critical samples daily, simultaneously and affordably.The author developed the SIDMIN program at ZCCM Nchanga Division where it continues to be a powerful tool for monitoring the efficiency of operations. Outlines are given of procedures for quick sample preparation and quantification of significant minerals in process samples. A specimen report is presented, which shows the format of reporting the contributions of individual minerals to metal losses at critical stages of the circuit. It is shown that SIDMIN provides timely information to management, about trends and abrupt changes in the quality of ore, and its processing, in a way never achievable by chemical analyses alone. This greatly helps in resolving the age-old problem of ‘bad ore’ or ‘bad operations’ on a day-by-day basis. For example increase in copper mica in the feed indicates excessive ore dilution during mining. Increased loss of free sulphides was traced to insufficient reagent conditioning time at the Concentrator. Persistent losses of leachable oxides at the Tailings Leach Plant were traced to inadequate leach residence time.SIDMIN is affordable because it can be implemented using basic optical microscopes, minimal quantities of micro-chemical reagents and custom trained site staff who demonstrate good colour perception and an ability to follow laid down procedures consistently."

Jan 1, 2000

By Michel Grenier, Robert Scott, Mahendra Gangal, Andrew Dasys

This research project which took place at Brunswick Mining and Smelting's Brunswick mine, was undertaken to assess the ability of new diesel engine technology to meet current and anticipated underground worker exposure limits to diesel exhaust contaminants. Concentrations of CO, CO2 NO, NO2 SO2 and respirable combustible dust (RCD) were measured in a remote mine area where a haulage truck was operating under simulated duty cycles. The 26 ton haulage truck was equipped with a 300 hp, electronically controlled engine. Fresh air was supplied to the area as per the MSHA certification document for this particular engine. Results showed that while the vehicle operated in a normal and realistic duty cycle, the concentrations of contaminants remained well below the ACGIH guidelines for the threshold limit values (TLV)for exposure. While operating at 630/0 of maximum horsepower (26 tons of ore in the dump), the time-weighted average exhaust gases concentrations (CO, CO2 NO, NO2 and SO2) never exceeded 150/0 of their respective TL Vs. ReD concentrations in this instance were measured at 0.59 mg/mJ or 39.30/0 of the exposure limit suggested by the Canadian ad hoc Diesel Committee. The Air Quality Index was 1.55 or 520/0 of the maximum suggested value for exposure.

Jan 1, 1994

By R. Hendrickson

In the 1940's a top blown water-cooled oxygen lance was developed to inject oxygen into liquid iron. This process, the LD or BOF process technique, today is used in 65% of the world's steel production, and represents the largest oxygen market for temperature enhancement in steel and non-ferrous smelting applications. There are three major approaches to the use of oxygen in metallurgical processes: (1) general enrichment of the air supplied to burners or tuyeres, (2) under-flame enrichment or injection, and (3) the use of an auxiliary oxy-fuel burner as a heat source. With each of these techniques there are technical and economic trade-offs.

Jan 1, 1990

By D Morgan, K Jones

"In March 2015 Northparkes Mines (NPM) installed a process mineralogy facility on-site. The laboratory included a TESCAN TIMA scanning electron microscope (SEM) and was the first SEM facility to be commissioned on a mine site in Australia. While the initial intent of the quantitative mineralogy laboratory was to provide information to drive processing plant improvements, in practice, it has been utilised for so much more and is now serving as an integral link between departments on-site. This multidisciplinary approach to orebody knowledge is a new strategy for NPM whereby all parts of the value chain are aligned towards the common goal of achieving process efficiency and stability while still maintaining high throughputs. The NPM experience is presented as a case study to illustrate how on-site process mineralogy can drive a realignment in business strategy with a common goal of mill optimisation, stability and more realistic forecasting through orebody knowledge and information sharing between disciplines.Citation:Jones, K and Morgan, D, 2016. On-site Process Mineralogy - Linking Departments and Disciplines with the Common Goal of Increasing Plant Performance, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 149–156 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By P. A. Young

The historical background of on-strand cooling is given, together with a resume of recent practical developments. Laboratory test procedures are then considered in detail, for both productivity and quality parameters, with particular reference to the design of the Ravenscraig No 3 machine (Scotland). A heat transfer model is presented for a porous sinter with propagating cracks. The influence of cooling/sintering area ratio, sinter strength, granulometry, return fines, coke consumption and FeO levels are examined in relation to economics. A detailed comparison of capital and running costs for two different strands, designed for identical duties, but with off or on-strand cooling, is then given.

Jan 1, 1977

By Guy Chevalier, Jean-Guy Chartrand, Louis Barrette, Daniel Michaud, Michel Fortin

"COREM has developed, specifically for the mineral industry, a mobile laboratory using the Laser-Induced Breakdown Spectroscopy (LIBS) technique. It has been used to perform onstream analysis (OSA) of the chemical composition of slurries in both gold-ore and iron-ore processing plants. Industrial tests have been carried out respectively at La Mine Doyon (Cambior), a gold-ore processing plant near Rouyn-Noranda, Quebec, and at QCM's iron-ore pelletizing plant in Port-Cartier, Quebec. The aim was to demonstrate that the LIBS technique is capable of providing information that meets the needs for process control. C, Si, Ca, Mg, Mn and Al were the elements targeted on iron ore while Cu, Fe, Ag and Au were targeted for gold ore. The results obtained meet or exceed the requirements for process control and consequently clearly show that the LIBS technique is suitable for industrial applications.The feasibility of OSA, through in-plant validations using COREM’s LIBS mobile laboratory, has been demonstrated in four essential aspects: slurry sampling, LIBS chemical measurement, robustness for continuous operation, and functionality for industrial operators.INTRODUCTIONThere is a general need for optimization in the mineral industry. Process control is a favoured means to achieve this goal (McKee 1991). Real-time knowledge of process status is the key to effective control (Da Silva 1994). Only a few techniques, such as XRF, NMR and digital imaging, are currently amenable to chemically monitor industrial processes (Braden 2002). LIBS is an emerging technique with appealing characteristics for on-line and real-time measurement of bulk material (Lorenzen 1992, Palanco 2000). While our ultimate goal is to provide our industrial partners with performing monitoring tools, a shorter-viewed objective is to demonstrate the feasibility of developing a LIBS system for OSA. The LIBS technique has shown interesting capabilities for measuring solids, liquids, dusts and gases. Our work has focused on mineral slurries (Barrette 1999 and 2001, Turmel 1999). Special equipment is needed to perform in-plant validations. A mobile laboratory based on the LIBS technology has been assembled for this task."

Jan 1, 2004

By N. W. Stump

New developments in on-stream analysis using immersed radioisotope gauges including results from plant installations are described. The control of grinding and flotation using a small digital computer has been complemented by this development. A control scheme for grinding which is based on maximum throughput at constant product size and preliminary work in flotation control are also outlined.

Jan 1, 1974

By J. J. Whittaker

Zaldivar is an open pit copper mine operation located in the Atacama Desert, in northern Chile. The plant produces Cu cathodes using 4 solvent extraction trains. The plant was started up May 1995. Since 1996 the plant has been using on-stream analyzers based on X-ray fluorescence and titration for process monitoring and control. Elemental analyzer alone is not able to provide the critical information for plant operation, it has to be complemented by on-stream titrators integrated to one sampling system. The analyzers are located in a prefabricated shelter. The analyzer system project, operation and performance issues are the main topic of this paper.

Jan 1, 1999

The lead concentration of flotation feed ore slurries is determined using two ?-ray absorption gauges mounted directly on a 6 in. diameter flotation feed pipeline. One gauge is a conventional "density" gauge using CS137. The other is a "lead-sensitive" gauge, which depends on the preferential absorption. by lead of 225 key y-rays resulting from Compton backscatter of CS137 y-rays.Gauge outputs are combined using an analogue computer the output signal of which is directly proportional to the lead concentration of the pulp. The accuracy of measurement of the pulp lead concentration is ± 3·6 per cent for ore slurries with lead concentrations in the range 0'07-0·16 g/c.c. and pulp densities 1.43-1.60 g/c.c.This paper sets out the development of the technique and details are given of the two experiments (1964, 1966) conducted in the plant at North Broken Hill Limited. The installation of the two-gauge system inthe plant during May 1968 is described. Details are given of the calibration technique used and the results obtained.

Jan 1, 1969

By V. L. Gravitis

Radioisotope X -ray techniques of analysis for nickel have been tested in laboratory and plant trials. In the laboratory tests. a comparison was made of radioisotope and conventional analyses for nickel in solid s samples taken from streams of a nickel concentrator. Coefficients of variation of 1.7% for feed and concentrate samples , and equal to 10% for final tailing samples, were obtained. Continuous determination of nickel in final tailing slurries was demonstrated in a trial lasting 20 days at a nickel concentrator (Western Mining Corporation), nickel being determined with a standard error of 0.036% Ni in the slurry solids within the range of 0.24 to 0.68% Ni. This error, obtained by comparison of on-stream probe analyses with assays of samples taken from the stream, includes errors in sampling and assay by conventional techniques.

Jan 1, 1977

In response to requests from the iron ore mining industry, the Commonwealth Scientific and Industrial Research Organisation (CSIRO) Division of Mineral Physics has developed a number of bulk analysis techniques in which analyses are obtained directly from ore samples weighing many kilograms or from ore located on conveyor belts.Because penetrating neutron and gamma radiation is used, measurements are obtained from a large volume of ore, which ensures thal the analyses are represelllative of the bulk.Two different gamma-ray techniques have been developed to measure iron ore grade. The first is based on backscallering of 60CO gamma rays, while the second involves measurement of the annihilation radiation which arises when the ore is irradiated wilh 226Ra gamma rays. Both techniques measure the iron concentration with an accuracy (1 s) of better than 0.4% Fe.A thermal-neutron irradiation technique using a 252Cf neutron source has been developed for the simultaneous determination of iron and the aluminium impurity (expressed as AI2O3) in iron ore fines on a conveyor bell. Because the conveyor speed must not exceed about 0.05 m/s, if good accuracy for AI2O3 is required, an auxiliary analysis bell is required Lo avoid inLerference with normal ore processing. Dynamic trials have demonstrated that accuracies of 0.6% Fe and 0.1% AI2O3 can be obtained.

Jan 1, 1985

By Peter Cammack

Where raw coal from a mine is treated in dense medium separators ash in the washed product is generally very consistent, provided control of the medium suspension is maintained at a given specific gravity. When, however, the washing process is a Baum jig or other similar apparatus, making a separation at rather arbitrary gravities, the control of the product ash is less accurate, particularly in those cases where the design capacity of the washbox is exceeded by the load of high ash fines. In either of these cases an instantaneous measurement of ash while not essential would be desirable, to check the quality of the washed product and provide operator or management with instantaneous warning of changes in ash. Nearly 60% of all British coal mined goes for electricity generation, to burn at 17% ash, and since the overall average ash content of raw coal as mined is about 30% and varies within a range of 18 ? 40%, incombustible material has to be removed. The ash specification could be met either by total washing, or by washing part and blending the clean coal produced with the remaining untreated coal. Some plants use a straight tonnage split, but generally speaking in Britain it has been found more economical to screen and wash the oversize only. In either case for effective quality control in blending an instantaneous determination of the ash content of the product as it is made has been found essential, since standard ash determination by pyrolysis methods is lengthy and provides information too late to be used in the control of plants blending at the rate of 1000 ton/h.

Jan 1, 1976

By S. K. Kawatra, Harrison R. Cooper

In the last 30 years, on-¬stream slurry analyzers have proven to be of great use in the control of mineral processing circuits. This review discusses the two most popular methods, x-ray fluorescence and neutron activation analysis, and also considers techniques which are still under development.

Jan 1, 1986

By Olli Haavisto, Lauri Koresaar, Navid Khajehzadeh

In recent times sustainable minerals processing is an important topic in research. Sustainable mining is linked with efficient use of energy and human resource in all process stages including beneficiation of the ore. Controlling and optimizing the recovery while preserving the grade of the concentrate is extremely important in flotation plants. This development requires new technological solutions and has given rise to the multitude of application areas for lasers. X-ray Fluorescence (XRF) and Laser-Induced Breakdown Spectroscopy (LIBS) are currently two of the predominant non-contact and direct analysing methods in industry. LIBS and XRF measurement techniques both have high capabilities for measuring elements. LIBS has a very simple and easy-to-implement spectroscopic setup, wider range of elements can be detected with online LIBS and measuring light elements is simpler by LIBS compared with XRF. It is of great interest to extract mineralogical information from the elemental results with no modification on the measurement setup. In order to achieve this, more advanced interpretation of the elemental peaks of LIBS spectra is required. Therefore, the major focus of this research is about measuring mineral concentrations from the elemental lines of LIBS spectra using advanced statistical methods. This accomplishment provides knowledge about mineral concentrations from the real-time assay data of the slurry LIBS analyzer. Consequently, this paper first discusses an analytical method called partial least squares regression leading to rapid mineral identification from the elemental contents of the LIBS technique. Then the technique is employed to analyze the mineral contents quantitatively through the information acquired from an on-stream LIBS slurry analyser. This can lead to many benefits such as rapid control of concentrate quality, enhanced recovery, saving time, energy and manpower.

Jan 1, 2016

By Richard D. Grove

The on-stream analysis of phosphorus and silica has not been possible by XRF techniques and only recently has some success been indicated with quantitative XRD for P. Yet there has been a recognized need for an on-stream analysis of P and acid insoluble to permit the automatic control of phosphate rock flotation plants which produce some 30-40 million tons of concentrate each year in the southeastern U.S. IMC Fertilizer, Inc., the largest U.S. phosphate rock producer, embarked on a program to develop such an on-stream analysis capability several years ago. Following many months of lab and prototype development, the first commercial installations started in December 1986 and now have completed some 400,000 analyses with surprising accuracy, precision and reliability. The use of these devices in the improved control of the phosphate flotation plant is currently receiving some very serious attention at IMC.

Jan 1, 1989

By Holmes R. J, Miles J. G

An on-stream shale detector has been developed that is suitable for use on conveyor belts carrying iron ore of up to 200 mm particle size. The shale is distinguished from high-grade iron ore by means of the substantially greater total natural gamma-ray activity (400-3000 keV) of the shale, which is due to the presence of uranium (214Bi), thorium (208TI) and potassium (40K). Other gangue materials, sueh as highly siliceous cherts and jaspilites, escape detection because of their low activity. A dynamic trial of the shale detector at Mt Whaleback, using a large-volume (100 × 100 400 mm long) "Polyscin" Nal(TI) gamma-ray detector, demonstrated that as little as 20 tonne of ore on a conveyor belt (equivalent to partial truckloads of ore) can readily be monitored for shale content.

Jan 1, 1981