Search Documents

By R. H. Smith, A. C. Polk

The physical properties of the materials are listed, together with a short explanation of how this material binds the sand grains together without materially reducing the effective permeability of the sand. The chemical can be used in wells with bottom-hole temperatures ranging from 105°F to more than 350°F A description of the equipment required and the techniques used for applying these plastics to the wells is included. Introduction Recovering oil and gas from unconsoli-dated sand formations offers one of the most troublesome of all production problems. These sands generally present no particular trouble while drilling is in progress, but after the well has been completed and a pressure differential has been established across the face of the producing zone, the formation begins to L'slough," resulting in "sanding up" of the well. The term "sanding up" means that sufficient volumes of sand have moved into the well bore or casing to cause a serious reduction or complete halt of all flow of oil, water or gas. In rare cases a well may produce only a small amount of sand and still continue to flow or pump, the sand being carried to the surface in the fluid stream. However, in such instances, the result may be a costly repair bill due to the effect of the sand on surface and pumping equipment. The difficulty of producing petroleum from sands that are loosely cemented has long been recognized by petroleum engineers but only within the last few years has any new approach to the problem been undertaken. This involves the use of plastics that are capable of bonding the individual sand grains in place without materially reducing the effective permeability of a formation. The successful application of plastics for the consolidation of poorly cemented sands is relatively recent but now it is widely used in many of the more difficult areas on the Gulf Coast of Texas and Louisiana. This relatively new use of plastics1 in the oil fields has been preceded by much laboratory and field research on the use of various chemicals2,3 for solving numerous well-completion and work-over problems. Plastics now are being used successfully to control gas-oil and water-oil ratios,4'6 in zone isolation, the repair of casing leaks, the elimination of caving in cable-tool drilling wells6'7 and in the setting of linerss and casing.9 Sand-consolidating plastics, however, are basically different from all others in that they must not form an impervious seal. Field Practices The approach to the sanding-up problem usually has been the mechanical obstruction of the movement of the sand grains.

Jan 1, 1947

By A. C. Polk, R. H. Smith

The physical properties of the materials are listed, together with a short explanation of how this material binds the sand grains together without materially reducing the effective permeability of the sand. The chemical can be used in wells with bottom-hole temperatures ranging from 105°F to more than 350°F A description of the equipment required and the techniques used for applying these plastics to the wells is included. Introduction Recovering oil and gas from unconsoli-dated sand formations offers one of the most troublesome of all production problems. These sands generally present no particular trouble while drilling is in progress, but after the well has been completed and a pressure differential has been established across the face of the producing zone, the formation begins to L'slough," resulting in "sanding up" of the well. The term "sanding up" means that sufficient volumes of sand have moved into the well bore or casing to cause a serious reduction or complete halt of all flow of oil, water or gas. In rare cases a well may produce only a small amount of sand and still continue to flow or pump, the sand being carried to the surface in the fluid stream. However, in such instances, the result may be a costly repair bill due to the effect of the sand on surface and pumping equipment. The difficulty of producing petroleum from sands that are loosely cemented has long been recognized by petroleum engineers but only within the last few years has any new approach to the problem been undertaken. This involves the use of plastics that are capable of bonding the individual sand grains in place without materially reducing the effective permeability of a formation. The successful application of plastics for the consolidation of poorly cemented sands is relatively recent but now it is widely used in many of the more difficult areas on the Gulf Coast of Texas and Louisiana. This relatively new use of plastics1 in the oil fields has been preceded by much laboratory and field research on the use of various chemicals2,3 for solving numerous well-completion and work-over problems. Plastics now are being used successfully to control gas-oil and water-oil ratios,4'6 in zone isolation, the repair of casing leaks, the elimination of caving in cable-tool drilling wells6'7 and in the setting of linerss and casing.9 Sand-consolidating plastics, however, are basically different from all others in that they must not form an impervious seal. Field Practices The approach to the sanding-up problem usually has been the mechanical obstruction of the movement of the sand grains.

Jan 1, 1947

By Kenneth B. Barnes, George H. Fancher

With the advent of water-flooding into active commercial usage in half a dozen areas in the Mid-Continent, the process passes the experimental stage and joins other methods and processes now in use which have been found suitable in one oil field or another in securing a more profitable production than has existed heretofore. The use of the air-gas lift, acidization, pressure maintenance and repressuring have presented their problems in economics and engineering during their introduction and extended application. When a new field is discovered or attention is turned to an old producing area in which these methods have not been considered, it is to be expected that these problems again arise. While some information is available as to the results obtained by water-flooding in a few localities in the Mid-Continent, the extrapolation of the sand data on which the results are based, for even generalized use in other areas and fields in the region, is hazardous. It is precarious to assume that the same physical condition will obtain in a sand over more than small, special areas. This paper is concerned with a brief presentation of such data as are available to the authors on existing operations, a survey of the region and extent to which application of the method seems most likely to be made, an estimation of the crude reserve existing for such operations, suggestions as to the importance of core analysis in guarding against uncontrolled floods and its usefulness in predicting ultimate recoveries, and comment on some of the economic phases involved. These subjects, as concerned with water-flooding in the East (notably Bradford, Pennsylvania), have been discussed in detail in the literature and are generally well known. Especially is this true of discussions of the mechanical equipment and various lease layouts and development patterns for water-flooding.

Jan 1, 1936

By Kenneth B. Barnes, George H. Fancher

With the advent of water-flooding into active commercial usage in half a dozen areas in the Mid-Continent, the process passes the experimental stage and joins other methods and processes now in use which have been found suitable in one oil field or another in securing a more profitable production than has existed heretofore. The use of the air-gas lift, acidization, pressure maintenance and repressuring have presented their problems in economics and engineering during their introduction and extended application. When a new field is discovered or attention is turned to an old producing area in which these methods have not been considered, it is to be expected that these problems again arise. While some information is available as to the results obtained by water-flooding in a few localities in the Mid-Continent, the extrapolation of the sand data on which the results are based, for even generalized use in other areas and fields in the region, is hazardous. It is precarious to assume that the same physical condition will obtain in a sand over more than small, special areas. This paper is concerned with a brief presentation of such data as are available to the authors on existing operations, a survey of the region and extent to which application of the method seems most likely to be made, an estimation of the crude reserve existing for such operations, suggestions as to the importance of core analysis in guarding against uncontrolled floods and its usefulness in predicting ultimate recoveries, and comment on some of the economic phases involved. These subjects, as concerned with water-flooding in the East (notably Bradford, Pennsylvania), have been discussed in detail in the literature and are generally well known. Especially is this true of discussions of the mechanical equipment and various lease layouts and development patterns for water-flooding.

Jan 1, 1936

By Eugene A. Stephenson, Leon J. Pepperberg

The natural gas industry is essentially a byproduct of the oil industry. When first discovered the gas was usually regarded as a nuisance, and even when found immediately associated with oil, or suspected to be so, it was customary to blow it freely into the air, in the hope that gas would shortly be replaced by a flow of oil. The early methods of production,' transportation, and utilization were neither economical nor efficient; the chief value of gas was based on its use as a fuel, with no regard to (1) its effect. upon the oil with which it was associated, (2) its importance as a lifting agent, or (3) to its possibilities for the manufacture of byproducts. The spread of scientific research among major gas and oil companies, manufacturers, and academic groups, has gradually brought recognition of the fact that many of the technical problems bearing on production, transportation and utilization are common to both the gas and the oil industry. A few of the problems that have received serious study, and from which highly gratifying results have been obtained, are: (1) gas measurement, (2) oil well and gas well capacity tests, (3) elimination of field waste, (4) design of pipe lines and compressor stations, (5) extraction of constituents which might interfere with the normal flow of gas through the line, (6) control of reservoir pressure, (7) estimation of reserves of both oil and gas, (8) control of water encroachment, (9) measurement of factors which influence fluid movement through sands, (10) solubility of gases in oils, (11) effect of dissolved gases upon the properties of the solution. These investigations have demonstrated that almost every problem relating to oil production also involves some phase of natural gas engineering. During the past 15 years the use of experimental methods for the discovery and measurement of obscure, influencing factors, which cannot be determined purely by hydrodynamic or thermodynamic analyses, have contributed much towards the progress made in solving the problems of the oil and gas industries. Most of the experimental work on

Jan 1, 1934

By Lombard Squires, W. K. Lewis, W. I. Thompson

Clays consist predominantly of hydrated silicates of alumina. The formula is frequently assumed to be A1203 . 2Si02 . 2H20,'and certain of I. North Carolina. Low plasticity. 11. Same as I, after washing. Low plasticity. III. Tennessee. Good plasticity. IV. Pennsylvania flint fireclay. Low plasticity. V. Laredo, Texas. Very plastic. CaO/Na2O corrected for GO2. VI. San Antonio, Texas. Fine grained, highly plastic. Moisture and CO2 were determined together at 18.8 per cent. VII. Selected crude bentonite, California. " Data from R. Ries: Clays. John Wiley & Sons, New York, 1927. them undoubtedly have substantially this composition, but in general the ratio of silica to alumina is considerably higher. However, they always contain water of chemical constitution, as shown by Table 1.

Jan 1, 1935

By B. C. Craft, T. J. Johnson, H. L. Kirkpatrick

Petroleum engineers are displaying considerable interest in the problems of cementing oil wells, especially in the Gulf Coast and California areas, where steep temperature gradients are encountered and where wells are being drilled to greater depths. Deep drilling, that is, at depths in excess of 7000 ft., has been undertaken in these areas only in the last few years and with this trend oil-well cementing requires more technical treatment. It is not the purpose of this paper to describe the scope and application of cement operations in the oil industry or to give the standard specifications, methods of sampling and testing of portland cement. The various testing methods have been described by the American Society for Testing Materials1, Uren2, Tickell and Wankowski3 and Rakestraw and Parsons4. The latter authors (pp. 50-58) have also described in detail the methods of cementing. The authors realize that it is impossible to reproduce in the laboratory the scale of forces and dimensions that exist at great depths, but an attempt has been made to scale down these dimensions proportionally. The selection of problems to be studied was based largely upon the practical questions asked by several of the largest operators in these fields. All cements used in these experiments met the specifications of the American Society for Testing Materials.

Jan 1, 1935

By James B. Graham, Earle E. Smith

The value of all minerals produced in the United States for the years 1930 to 1932 averaged $3,460,000,000 annually, according to Bureau of Mines reports. Of this amount, approximately $1,280,000,000 represents nonmetallic substances, such as petroleum, gas, sulfur and salt produced as fluids. Thus, about.37 per cent of the country's mineral wealth is procured through wells drilled in the earth, which require casing to keep them open throughout their life. Deep well drilling has increased greatly in the last few years. Several strings of casing have been set deeper than 9000 ft.—one, a string of 7?-in. O.D. casing, 10,301 ft. long, run in a well drilled by the Gulf Production Co. in West Texas, holds the record up to this time. These are longer strings than were contemplated when the American Petroleum Institute Specifications were adopted 10 years ago, therefore it is necessary to consider whether the present joint standards are adequate for such strings, or for even longer strings that may be called for in the future. Petroleum engineers are asking: Is there a possibility that stronger joints can be designed without going to stronger and more costly steels than offered in present specifications? Without sacrificing too greatly the tensile properties of the joint, can its design be changed to allow more clearance in the open hole below the next larger string of casing, and thus avoid costly underreaming? What can manufacturers offer for drilling through heaving shale? Fundamentals of the Problem During the last few years considerable study has been given to casing joints and their limitations, and since attention must be given to this subject by those who will be required to drill deeper holes, it is timely to review the fundamentals of the problem. These will be recognized generally as the following: 1. No threaded joint can be stronger than the area of metal under the root of the first perfect thread, and this area must be large enough

Jan 1, 1935

By C. W. Gibbs, E. K. Parks

In 1929 the Standard Oil Company of California commenced the development of a device for obtaining temperatures and pressures in flowing and shut-in wells and of suitable running equipment for such a recorder. Although simple in principle, the recorder has required much experimental work in its development. The various problems have now been solved to such an extent that it is believed that the apparatus affords a sturdy and reliable means for obtaining information regarding depth pressures,—apparatus that may be turned over to a well gang for routine operation. As an example of the rough usage the device will withstand a recent incident may be cited. Owing to failure of the lowering line at the conclusion of a run a recorder was dropped some 6300 ft. through 2 1/2-in. tubing filled with gassy oil. The device was fished out undamaged and with the pressure record intact, although the instrument had been subjected to a pressure greater than 2300 lb. per sq. in. for some 24 hr. after impact at bottom. Description of Recorder The instrument is of the continuous recording loaded spring type (Fig. I). Temperature is not recorded continuously but is obtained by maximum recording thermometers in an auxiliary thermometer well. The entire instrument assembly, from bottom of the recorder to top of the socket, is 6 1/2 ft. long and weighs less than 25 lb. The maximum outside diameter of the recorder shell is 1 1/4in., and all attachments need be no larger. This permits lowering the device inside 2-in. tubing. The operating principle is simple. The well pressure acts upon a piston A resisted by the extension of spring B. The spring deflection is recorded by a stylus C upon paper within the recording drum D. Springs.—To improve accuracy at lower maximum well pressures five interchangeable spring assemblies are used. These have maximum pressure ranges of from 250 to 5000 lb. per sq. in. Piston diameter is the same in all cases, and each spring is designed for a deflection of about 5 in. for maximum pressure loading. A complete spring assembly there-

Jan 1, 1934

By W. K. Lewis

During the last decade the petroleum refinery engineer has made great progress in achieving a better understanding of the physical behavior of hydrocarbon mixtures, with particular reference to their pressure-temperature-volume relationships, the mechanism of the evaporation of liquids, the condensation of vapors, including the changes in composition, and the heat effects accompanying them. With the new insight into the mechanism of movement of oil and gas through the formations in which they occur, achieved by the production engineer, it is clear that the latter will need to utilize in the solution of his own problems much of the information outlined above. It is the purpose of this paper to outline the portions of that information that seem most certain to prove of importance in production work. Properties of Pure Hydrocarbons While it is true that petroleum always consists of highly complex mixtures of hydrocarbons, none the less understanding of the behavior of the mixture must be based upon a knowledge of the properties of the pure components. However, in view of the tremendous number of hydrocarbons existing in petroleum, the determination and formulation of the properties of all of them would seem a discouraging task. The difficulty of the situation is increased by the undoubted facts that the overwhelming majority of chemical individuals in petroleum have never been isolated as pure compounds, none of their physical properties have been determined and even their chemical constitution is unknown. The situation would be hopeless were it not for the fact that certain extraordinary correlations of important properties of various hydrocarbons have been discovered which make it possible to predict those properties for a given chemical individual on the basis of a very limited characterization of it. Thus one can predict the vapor-pressure curve of an unknown hydrocarbon over a considerable range from the knowledge of a

Jan 1, 1934

By C. E. Reistle, G. L. Nye

The East Texas field is in Smith, Rusk, Gregg, Upshur and Cherokee counties, Texas. The discovery well was completed Sept. 8, 1930, near the eastern limit of the field. Within less than one year the new field became the dominant factor in the world production of crude oil. On Aug. 16, 1931, eleven months after completion of the discovery well, there were 1644 wells in the field, and the average daily production was 584,475 bbl. Since that time the number of wells has increased to 8195 on Oct. 1, 1933, and the field has produced 385,979,691 bbl. of oil. The geology of the East Texas field has been discussed by Lahee,1 Levorsen,2 Minor and Hanna3 and others, and it will not be discussed in detail here. The field is a structure of the monocline type on the westward dipping homocline between the Sabine uplift and the East Texas geosyncline. Production is obtained from the Woodbine group, which has been truncated and then sealed by the Austin chalk, which rests unconformably upon it. The oil-saturated part of the sand lies bettween a sub-sea depth of 3050 ft. on the east side of the field, where the Woodbine sand stops and the Austin chalk rests directly upon older formations, and a sub-sea depth of 3320 ft., which was the average depth of the water table in the sand at the time the field was discovered. The field is about 40 miles long and has an average width of approximately 4 1/2 miles. The area within the proven limits of the field is close to 116,580 acres and the normal Woodbine water underlies nearly 62,000 acres on the western side of the field at the present time. The field is unusual in several respects: (1) the tremendous size of the reservoir system and the quantity of oil in place; (2) the large area of the oil and water contact, which makes water movement possible into the oil-bearing part of the structure; (3) the absence of free gas within the main producing sand of the field. Changes in the reservoir pressure during the production history of the field have been greatly affected by

Jan 1, 1934

By Ralph J. Schilthuis, William Hurst

The nature of the forces that are important in producing the oil in the East Texas field and the manner in which these forces are affected by the rate of production have always been problems of outstanding interest. These questions are of great interest to the industry as a whole on account of the economic importance of the East Texas field and to the engineers in particular on account of the unique character and behavior of the field. Subsurface pressure data throughout the field have been collected systematically, so that a quite complete history of the reservoir pressures has been kept as the field has been developed and produced. Subsurface samples of the oil and gas have been taken and these have been examined to obtain data on the physical properties of the reservoir fluids under the actual conditions of temperature and pressure. All of these data have been valuable because they have afforded the basis for a careful study of the means by which the oil is produced. It is the purpose of this discussion first to point out several of the important facts revealed by the data mentioned and then to describe studies that have been made concerning the interpretation of these facts. Reservoir Pressure Data and Properties of Oil The reservoir pressure data on the East Texas field have shown conclusively that the pressures are readily affected by changes in the rate at which the field is produced. This can well be seen in Fig. 1, where the average reservoir pressures obtained from time to time are plotted with the daily production rates and the cumulative production of the field. It is noted that the average reservoir pressure has declined irregularly, depending upon the rate of production, from the estimated original value of 1625 Ib. per sq. in. to the value of 1228 lb. per sq. in. observed for Aug. 11,1934. The decline in pressure has been more rapid at the higher rates of production than at the lower rates. In contrast, the average reservoir pressure has increased, on several occasions, upon reduction of the withdrawal rate from a high value to a lower value. The reservoir pressure data have also shown that a definite gradient in pressure has existed across the field from west to east since the begin-

Jan 1, 1935

By Walter Miller

Any annual review of engineering progress in petroleum refining must of necessity include many features mentioned in earlier reviews. Advances do not spring mushroom fashion to wide acceptance overnight, but rather resemble rolling snowballs, gathering size and velocity as they progress. The new ideas of one year develop through the course of scattered adoption and testing during following years, to be ultimately discarded or to become an integral part of refinery engineering and operation. Polymerization and Cracking As an illustration, the publicity given to the polymerization and cracking of petroleum gases during the year has given many the impression that this is a new art. But patent and technical literature have disclosed active work on the problem dating back a decade or more and a unit capable of making 100 bbl. a day of polymer gasoline was constructed as early as 1930. Important strides have been made during 1935 looking to the more general commercialization of available processes, and some four important groups are furthering this work. In addition to the production of liquid products for inclusion as a constituent of commercial motor fuel, polymerization has also been a factor leading to the installation of a plant at the Houston refinery of The Shell Petroleum Corporation for manufacturing isooctane for aviation use, by making available dibutylene for catalytic hydrogenation Polymerization is not confined to unsaturated hydrocarbon gases as a source of raw material, and has been extended to include a preliminary decomposition of normal saturated gases under suitable heat and pressure conditions into the unsaturated types, which can then be used as raw material for the polymerization process. Thus there is opened up the possibility of eventually using large quantities of natural gas in the manufacture of high-grade motor fuels, although the early commercial growth will be largely on cracking still gases for economic reasons. Such utilization will result in a somewhat lowered drain on crude-oil reserves and a partial elimination of the

Jan 1, 1936

By Walter Miller

Any annual review of engineering progress in petroleum refining must of necessity include many features mentioned in earlier reviews. Advances do not spring mushroom fashion to wide acceptance overnight, but rather resemble rolling snowballs, gathering size and velocity as they progress. The new ideas of one year develop through the course of scattered adoption and testing during following years, to be ultimately discarded or to become an integral part of refinery engineering and operation. Polymerization and Cracking As an illustration, the publicity given to the polymerization and cracking of petroleum gases during the year has given many the impression that this is a new art. But patent and technical literature have disclosed active work on the problem dating back a decade or more and a unit capable of making 100 bbl. a day of polymer gasoline was constructed as early as 1930. Important strides have been made during 1935 looking to the more general commercialization of available processes, and some four important groups are furthering this work. In addition to the production of liquid products for inclusion as a constituent of commercial motor fuel, polymerization has also been a factor leading to the installation of a plant at the Houston refinery of The Shell Petroleum Corporation for manufacturing isooctane for aviation use, by making available dibutylene for catalytic hydrogenation Polymerization is not confined to unsaturated hydrocarbon gases as a source of raw material, and has been extended to include a preliminary decomposition of normal saturated gases under suitable heat and pressure conditions into the unsaturated types, which can then be used as raw material for the polymerization process. Thus there is opened up the possibility of eventually using large quantities of natural gas in the manufacture of high-grade motor fuels, although the early commercial growth will be largely on cracking still gases for economic reasons. Such utilization will result in a somewhat lowered drain on crude-oil reserves and a partial elimination of the

Jan 1, 1936

By Walter Miller

BY the beginning of 1945 the output of petroleum products for war had reached a volume and a rate of growth which practically assured all requirements so long as war continued. The programs for making gasoline, lubricating oils of required quality, toluene for T.N.T., and chemicals for manufacture of synthetic rubber, as well as numerous other lesser petroleum products, were all well in hand, and unless catastrophic developments occurred there was no doubt of the ability of the industry to meet all demands. The end of the fighting found the refining industry working at top capacity on war commodities, but also in position to convert quickly into peacetime civilian production. 100-octane Aviation Gasoline Production of the vital 100-octane aviation gasoline, starting with approximately 44,000- bbl. daily capacity at our entry into the war, reached a top of 525,000 bbl. a day in the United States by the end of hostilities. With 75,- bbl. from other Allied sources, the grand total was 600,000 bbl., or 25,000,000 gal. each 24 hr. available to the armed forces had fighting continued. At times it was a close race between requirements and production, but never were any important military operations involving the use of high-octane aviation gasoline held up or delayed for lack of sufficient output of such material. The undivided effort of the entire refining industry in full cooperation with the Government made this record possible. Little diminution in output followed the German surrender on May 7. Plans called for a correspondingly greater activity for the Japanese war and possibly for well into 1946. But when the Japanese sued for peace on Aug. 10 most contracts were quickly canceled. Substantial stocks, reputed to be somewhere between 20,000,000 to 30,000,000 bbl., built up largely between V-E and V-J day pending organization of the larger Japanese war program envisaged after Germany gave up, were in the Government's hands in this country, in addition to working stocks in the war areas. Toluene and Lubricating Oil Requirements for toluene for T.N.T. increased rapidly as bombing speeded UP with increasing control of the air by the Allies in Europe and Asia. Production in excess of T.N.T. requirements which had been going into 1000-Octane aviation fuel blending during 1943 and 1944 was again drawn into explosive manufacture early in 1945. In anticipation of the war continuing into 1946, two new plants were ordered constructed, the decision being announced in April, plans calling for one of them to get into production about the end of 1945, the other in the first quarter of 1946. Both of these projects were later canceled as victory made it evident that the additional supplies would not be needed. Production was

Jan 1, 1946

By Walter Miller

BY the beginning of 1945 the output of petroleum products for war had reached a volume and a rate of growth which practically assured all requirements so long as war continued. The programs for making gasoline, lubricating oils of required quality, toluene for T.N.T., and chemicals for manufacture of synthetic rubber, as well as numerous other lesser petroleum products, were all well in hand, and unless catastrophic developments occurred there was no doubt of the ability of the industry to meet all demands. The end of the fighting found the refining industry working at top capacity on war commodities, but also in position to convert quickly into peacetime civilian production. 100-octane Aviation Gasoline Production of the vital 100-octane aviation gasoline, starting with approximately 44,000- bbl. daily capacity at our entry into the war, reached a top of 525,000 bbl. a day in the United States by the end of hostilities. With 75,- bbl. from other Allied sources, the grand total was 600,000 bbl., or 25,000,000 gal. each 24 hr. available to the armed forces had fighting continued. At times it was a close race between requirements and production, but never were any important military operations involving the use of high-octane aviation gasoline held up or delayed for lack of sufficient output of such material. The undivided effort of the entire refining industry in full cooperation with the Government made this record possible. Little diminution in output followed the German surrender on May 7. Plans called for a correspondingly greater activity for the Japanese war and possibly for well into 1946. But when the Japanese sued for peace on Aug. 10 most contracts were quickly canceled. Substantial stocks, reputed to be somewhere between 20,000,000 to 30,000,000 bbl., built up largely between V-E and V-J day pending organization of the larger Japanese war program envisaged after Germany gave up, were in the Government's hands in this country, in addition to working stocks in the war areas. Toluene and Lubricating Oil Requirements for toluene for T.N.T. increased rapidly as bombing speeded UP with increasing control of the air by the Allies in Europe and Asia. Production in excess of T.N.T. requirements which had been going into 1000-Octane aviation fuel blending during 1943 and 1944 was again drawn into explosive manufacture early in 1945. In anticipation of the war continuing into 1946, two new plants were ordered constructed, the decision being announced in April, plans calling for one of them to get into production about the end of 1945, the other in the first quarter of 1946. Both of these projects were later canceled as victory made it evident that the additional supplies would not be needed. Production was

Jan 1, 1946

By R. L. Boyer, F. Morgan, M. Muskat

In the last several years a type of application of the fundamental permeability-saturation relationships has been developed which offers great promise in the interpretation of general reservoir performance.l-' In these developments no attempt is made to solve the detailed flow dynamics in actual oil and gas-producing systems. That problem still remains unsolved. But the permeability-saturation phenomena are incorporated in the analysis of oil-producing reservoirs in a manner such as to reflect the true role they play in controlling the gross reservoir behavior. In particular, they are introduced in such a manner as to determine the gas-oil ratio of the production at any stage of depletion, and, when combined explicitly with the so-called material-balance principles in differential form, one can obtain a differential equation describing completely the average pressure and gas-oil-ratio history of oil-producing reservoirs. While thus far they have been applied directly only to gas-drive reservoirs, they are susceptible of extension to partial water-drive systems, and qualitatively the same principles are of value in the study Of complete water-drive reservoirs. Moreover, in addition to giving a means for computing the variation of the reservoir pressure and gas-oil ratios vs. the cumulative production, they automatically lead to predictions of the gross ultimate recovery under natural depletion—and when properly extended they provide means for predicting the ultimate recovery under gas or water injection. The data required for such applications are the initial fluid distribution in the producing section, the pressure-volume-temperature data on the gas and liquid phases, and the permeability-saturation relationship for the oil-satuiated zone. The former can be obtained with reasonable accuracy by methods that are well established and available throughout the industry. The permeability-saturation data, however, involve techniques that are not at all standardized. In fact, only

Jan 1, 1947

By M. Muskat, R. L. Boyer, F. Morgan

In the last several years a type of application of the fundamental permeability-saturation relationships has been developed which offers great promise in the interpretation of general reservoir performance.l-' In these developments no attempt is made to solve the detailed flow dynamics in actual oil and gas-producing systems. That problem still remains unsolved. But the permeability-saturation phenomena are incorporated in the analysis of oil-producing reservoirs in a manner such as to reflect the true role they play in controlling the gross reservoir behavior. In particular, they are introduced in such a manner as to determine the gas-oil ratio of the production at any stage of depletion, and, when combined explicitly with the so-called material-balance principles in differential form, one can obtain a differential equation describing completely the average pressure and gas-oil-ratio history of oil-producing reservoirs. While thus far they have been applied directly only to gas-drive reservoirs, they are susceptible of extension to partial water-drive systems, and qualitatively the same principles are of value in the study Of complete water-drive reservoirs. Moreover, in addition to giving a means for computing the variation of the reservoir pressure and gas-oil ratios vs. the cumulative production, they automatically lead to predictions of the gross ultimate recovery under natural depletion—and when properly extended they provide means for predicting the ultimate recovery under gas or water injection. The data required for such applications are the initial fluid distribution in the producing section, the pressure-volume-temperature data on the gas and liquid phases, and the permeability-saturation relationship for the oil-satuiated zone. The former can be obtained with reasonable accuracy by methods that are well established and available throughout the industry. The permeability-saturation data, however, involve techniques that are not at all standardized. In fact, only

Jan 1, 1947

By Norris Johnston, Carrol M. Beeson

The gravimetric-vacuum distillation method was developed to permit rapid and accurate determinations of the oil-water ratios of small samples or sands containing little oil. In addition, the samples usually are so well cleaned and so little altered by the distillation at reduced pressure that rapid estimations of other physical properties may be made with the evacuated cores. Requiring only elementary glass-blowing technique, the distilling tubes and traps used in determining oil-water ratios were easily fashioned from the usual glassware. A sketch and description are given of the necessary apparatus, including the cylindrical electrical heaters. The procedure, requiring about 40 min., consists in raising the temperature and maintaining it between 675' and 725°F. for at least 10 min. while the pressure is held between I and 2 mm. Hg. The fluids condensed in the trap (cooled by a mixture of kerosine and solid carbon dioxide) are separated in a centrifuge and the volume of water is recorded. Determination of changes in weight with an analytical balance of all parts of the apparatus permits computation of weight of oil distilled and total weight of oil recovered. Introduction In determining the oil-water ratios of core samples, distillation at atmospheric pressurel-5 has proved to be sufficiently reliable for samples containing moderate quantities of oil. Since small samples and sands with little oil are encountered, how- ever, it appeared advisable to develop a method that would be applicable under these circumstances. Thegravimetric-extraction procedure1,6-9 undoubtedly is very reliable and could be used in all tests, but the time consumed in the determination would often delay field operations. This would be especially true when dealing with tight sands or viscous oils, both of which retard the extraction process. Accordingly, the gravimetric-vacuum distillation method was developed in order to combine the good features of both of the older methods; that is, accuracy and speed. By reducing the pressure, it was found possible to perform the distillation at a temperature that permits the use of glass apparatus, all parts of which can be weighed on an analytical balance. Thus, the fluids may be removed quickly from the core, the water is readily trapped and measured, and the loss in weight of the core is easily determined. In addition, the total weight of material condensed in the distilling tube and in the trap provides a method of determining the oil-water ratio that is practically independent of the one involving the loss in weight of the sample. The use of vacuum not only permits as much accuracy as does the gravimetric-extraction process, but it actually allows an increase in speed over the atmospheric-distillation method, because of the time required to cool the metal pots from about 1200°F. between runs. More important yet, the innovation makes possible the almost immediate reporting of permeability, and saturation, which is impossible

Jan 1, 1946

By Norris Johnston, Carrol M. Beeson

The gravimetric-vacuum distillation method was developed to permit rapid and accurate determinations of the oil-water ratios of small samples or sands containing little oil. In addition, the samples usually are so well cleaned and so little altered by the distillation at reduced pressure that rapid estimations of other physical properties may be made with the evacuated cores. Requiring only elementary glass-blowing technique, the distilling tubes and traps used in determining oil-water ratios were easily fashioned from the usual glassware. A sketch and description are given of the necessary apparatus, including the cylindrical electrical heaters. The procedure, requiring about 40 min., consists in raising the temperature and maintaining it between 675' and 725°F. for at least 10 min. while the pressure is held between I and 2 mm. Hg. The fluids condensed in the trap (cooled by a mixture of kerosine and solid carbon dioxide) are separated in a centrifuge and the volume of water is recorded. Determination of changes in weight with an analytical balance of all parts of the apparatus permits computation of weight of oil distilled and total weight of oil recovered. Introduction In determining the oil-water ratios of core samples, distillation at atmospheric pressurel-5 has proved to be sufficiently reliable for samples containing moderate quantities of oil. Since small samples and sands with little oil are encountered, how- ever, it appeared advisable to develop a method that would be applicable under these circumstances. Thegravimetric-extraction procedure1,6-9 undoubtedly is very reliable and could be used in all tests, but the time consumed in the determination would often delay field operations. This would be especially true when dealing with tight sands or viscous oils, both of which retard the extraction process. Accordingly, the gravimetric-vacuum distillation method was developed in order to combine the good features of both of the older methods; that is, accuracy and speed. By reducing the pressure, it was found possible to perform the distillation at a temperature that permits the use of glass apparatus, all parts of which can be weighed on an analytical balance. Thus, the fluids may be removed quickly from the core, the water is readily trapped and measured, and the loss in weight of the core is easily determined. In addition, the total weight of material condensed in the distilling tube and in the trap provides a method of determining the oil-water ratio that is practically independent of the one involving the loss in weight of the sample. The use of vacuum not only permits as much accuracy as does the gravimetric-extraction process, but it actually allows an increase in speed over the atmospheric-distillation method, because of the time required to cool the metal pots from about 1200°F. between runs. More important yet, the innovation makes possible the almost immediate reporting of permeability, and saturation, which is impossible

Jan 1, 1946