Search Documents

By C. M. Moncrief, B C. Craft

A bentonite-clay drilling mud when treated with tetrasodium pyroarsenate underwent substantially the same reduction in viscosity and water loss as when treated with the complex phosphates. The complex arsenate showed a slightly higher reversion after heating; the other arsenates showed poor viscosity-reducing properties. Introduction During the past 10 years the chemical control of drilling mud has become of major importance in affecting the successful drilling and working over of wells. The desired properties of drilling mud have been well established, and in obtaining these characteristics there has developed a large market for viscosity-reducing chemicals. Viscosity reduction produced by humic acid, tannic acid, sodium silicate, sodium tannate, Calgon, and the complex phosphates has been described by Loomis, Ford, and Fidiam.l The effects Of treatment with complex phosphates and ammonium PolyPhosPhates on the rheological properties of muds were investigated by Fancher2 and the alkali vanadates have been described by Williams.3 Laboratory Investigations It is the purpose of this paper to point out the effects of arsenates in controlling the viscosity and gelling characteristics of a drilling mud. Viscosities and gel strengths were measured at room temperatures with a Stormer viscosimeter calibrated in centipoises and operated at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester at a pressure of I00 lb. per sq. in. for 30 min. The hydrogen-ion concentration was measured with a glass electrode. The bentonite-clay suspensions were prepared in the laboratory and allowed to age several days before testing. Members of the Arsenic Group in the periodic Table include arsenic, antimony and bismuth, but this investigation was limited to arsenic. Phosphorus also occurs in Group V of the Periodic system and phosphorus and arsenic form many closely related compounds such as pH3 and AsH3, P2O5 and As2O5, H3PO4 and H3AS04 Samples of tetrasodium pyroarsenate were prepared by fusing c.p. disodium arsenate (Na2HA5O4.7H2O). According to Friend,' this re-forms the ortho-arsenate on dissolution in water. Sodium trihydrodiorthoarsenate was prepared as described by Mellor,5 from arsenic pen-toxide as follows: As2O5 + 3H20 -> 2H3AsO4 2H3AS04 + 3NaOH Na3H3(AsO4)2 .3H20 Sodium dihydrogen orthoarsenateWaHz-As04) was obtained by fusing together equivalent quantities of arsenious Oxide and sodium nitrate, dissolving the residue in water and allowing it to crystallize.

Jan 1, 1946

By C. M. Moncrief

A bentonite-clay drilling mud when treated with tetrasodium pyroarsenate underwent substantially the same reduction in viscosity and water loss as when treated with the complex phosphates. The complex arsenate showed a slightly higher reversion after heating; the other arsenates showed poor viscosity-reducing properties. Introduction During the past 10 years the chemical control of drilling mud has become of major importance in affecting the successful drilling and working over of wells. The desired properties of drilling mud have been well established, and in obtaining these characteristics there has developed a large market for viscosity-reducing chemicals. Viscosity reduction produced by humic acid, tannic acid, sodium silicate, sodium tannate, Calgon, and the complex phosphates has been described by Loomis, Ford, and Fidiam.l The effects Of treatment with complex phosphates and ammonium PolyPhosPhates on the rheological properties of muds were investigated by Fancher2 and the alkali vanadates have been described by Williams.3 Laboratory Investigations It is the purpose of this paper to point out the effects of arsenates in controlling the viscosity and gelling characteristics of a drilling mud. Viscosities and gel strengths were measured at room temperatures with a Stormer viscosimeter calibrated in centipoises and operated at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester at a pressure of I00 lb. per sq. in. for 30 min. The hydrogen-ion concentration was measured with a glass electrode. The bentonite-clay suspensions were prepared in the laboratory and allowed to age several days before testing. Members of the Arsenic Group in the periodic Table include arsenic, antimony and bismuth, but this investigation was limited to arsenic. Phosphorus also occurs in Group V of the Periodic system and phosphorus and arsenic form many closely related compounds such as pH3 and AsH3, P2O5 and As2O5, H3PO4 and H3AS04 Samples of tetrasodium pyroarsenate were prepared by fusing c.p. disodium arsenate (Na2HA5O4.7H2O). According to Friend,' this re-forms the ortho-arsenate on dissolution in water. Sodium trihydrodiorthoarsenate was prepared as described by Mellor,5 from arsenic pen-toxide as follows: As2O5 + 3H20 -> 2H3AsO4 2H3AS04 + 3NaOH Na3H3(AsO4)2 .3H20 Sodium dihydrogen orthoarsenateWaHz-As04) was obtained by fusing together equivalent quantities of arsenious Oxide and sodium nitrate, dissolving the residue in water and allowing it to crystallize.

Jan 1, 1946

By Henry Schaefer

Solution by electric analogy of performance problems of reservoirs containing oil and gas has heretofore depended upon a process of successive approximations based on material-balance calculations, because of variation in fluid compressibility. By the addition or subtraction of electric condenser capacity, the analogy network can be adjusted automatically for changing compressibility due to evolution of gas in the reservoir. The addition of a condenser is accomplished by an electronic circuit, which is described; subtracting a condenser is done by merely opening the electrical circuit by means of a relay. Introduction V. Paschkis and H. D. Baker1 first developed in this country a method of applying the analogy of flow of electric current in noninductive circuits to solution of heat-flow problems and suggested its application for certain other problems, such as flow of fluids or mass transfer and chemical diffusion. Necessary details for applying the analogy to flow of fluids in porous media were developed by IV. A. Bruce;= he classified3 the types of analysis and predictions that can be made by the analogy in class I, when the reservoir contains oil but no gas for the period under consideration; in Class 2, when both oil and gas exist in the free state in the reservoir sometime during the period under consideration. Duplication of bottom-hole pressure history and predictions for class I reservoirs can be obtained directly by electric analogy. Until now, the solution of problems pertaining to reservoirs in class 2 was obtained by successive approximations along with material-balance calculations. The object of this paper is to present a method for simplifying the application of electric analogy to class 2 reservoirs, resulting in a solution of these problems as direct as is possible for class I reservoirs. This is accomplished by an electronic control circuit, which adjusts the analogy network for changing compressibilities of fluids contained in the reservoirs. Analogy Network In electrical phenomena the analogy to two-dimensional fluid flow in a porous media is that of current flow through an ideal conducting sheet. This sheet, perfectly insulated on both sides, has resistance and capacitance uniformly distributed throughout its area but is of negligible inductance. The need for having the surface boundaries perfectly insulated is that good correspondence may be had with a permeable fluid-conducting stratum bounded above and below by impermeable media. 111 actual application the ideal conducting sheet, which has distributed parameters, is replaced by a network having lumped values of resistance and capacitance—the resistances are series elements and the capacitances are shunt elements. The larger the number of lumped

Jan 1, 1947

By Henry Schaefer

Solution by electric analogy of performance problems of reservoirs containing oil and gas has heretofore depended upon a process of successive approximations based on material-balance calculations, because of variation in fluid compressibility. By the addition or subtraction of electric condenser capacity, the analogy network can be adjusted automatically for changing compressibility due to evolution of gas in the reservoir. The addition of a condenser is accomplished by an electronic circuit, which is described; subtracting a condenser is done by merely opening the electrical circuit by means of a relay. Introduction V. Paschkis and H. D. Baker1 first developed in this country a method of applying the analogy of flow of electric current in noninductive circuits to solution of heat-flow problems and suggested its application for certain other problems, such as flow of fluids or mass transfer and chemical diffusion. Necessary details for applying the analogy to flow of fluids in porous media were developed by IV. A. Bruce;= he classified3 the types of analysis and predictions that can be made by the analogy in class I, when the reservoir contains oil but no gas for the period under consideration; in Class 2, when both oil and gas exist in the free state in the reservoir sometime during the period under consideration. Duplication of bottom-hole pressure history and predictions for class I reservoirs can be obtained directly by electric analogy. Until now, the solution of problems pertaining to reservoirs in class 2 was obtained by successive approximations along with material-balance calculations. The object of this paper is to present a method for simplifying the application of electric analogy to class 2 reservoirs, resulting in a solution of these problems as direct as is possible for class I reservoirs. This is accomplished by an electronic control circuit, which adjusts the analogy network for changing compressibilities of fluids contained in the reservoirs. Analogy Network In electrical phenomena the analogy to two-dimensional fluid flow in a porous media is that of current flow through an ideal conducting sheet. This sheet, perfectly insulated on both sides, has resistance and capacitance uniformly distributed throughout its area but is of negligible inductance. The need for having the surface boundaries perfectly insulated is that good correspondence may be had with a permeable fluid-conducting stratum bounded above and below by impermeable media. 111 actual application the ideal conducting sheet, which has distributed parameters, is replaced by a network having lumped values of resistance and capacitance—the resistances are series elements and the capacitances are shunt elements. The larger the number of lumped

Jan 1, 1947

By T. H. Dunn, P. L. Menaul

This paper discusses the results of an investigation made to develop a method of combatting corrosion of subsurface oil-well equipment caused by brines containing hydrogen sulphide. Carbon monoxide, aldehydes, and certain cyanide compounds were found by laboratory tests to effectively inhibit corrosion of steel by sulphide brines. Experiments were made for one year in eight wells in West Texas fields using formaldehyde as an inhibitor. It was found that the inhibitor treatment successfully prevented the severe corrosion previously experienced in these wells, and effected important net savings in operating costs. Introduction Corrosion of oil-field equipment has long been a problem in areas producing sour crudes. These areas include the major fields of Arkansas, Western Kansas, West Texas and New Mexico. Corrosion in these fields is caused primarily by the chemical action of hydrogen sulphide in the presence of water and by electric currents entering the wells through flow lines. Hydrogen sulphide is noncorrosive to iron or steel in the absence of water but under the usual conditions prevailing in oil wells where more or less water is present, hydrogen sulphide is very corrosive. This type of corrosion occurs over the pH range below 9, which includes all natural oil-field brines. If air is present in addition to hydrogen sulphide and water, corrosion proceeds at an extremely rapid rate. It was reported several years ago that a string of oil-well tubing was literally dissolved within 50 days where an air lift was used on a well producing considerable water and hydrogen sulphide. Air is generally absent in wells producing sour crude. After hydrogen sulphide corrosion starts, it proceeds with increasing severity and its correction becomes progressively more difficult. This characteristic of sulphide corrosion has been attributed to the formation of galvanic couples between the iron and steel equipment on one hand and the products of corrosion on the other.' Severe corrosion of subsurface oil-well equipment leads to a multitude of troubles. In addition to destruction of costly equipment, producing sands often are damaged by flooding with water leaking through corroded casing; bad mechanical conditions may develop in a well due to obstructions caused by corroded equipment lost in the hole, or partly collapsed casing; pumping operations are interfered with, and severe emulsification problems may result from the homogenizing action of corroded balls and seats.% A typical case of severe corrosion caused by hydrogen sulphide was reported in Howard County, Texas, where it was necessary to pull tubing once a week to repair leaks after the tubing had been in use for only one year. On one well in this area a string of tubing was pulled 11 times in 8 months; 11 joints of tubing being replaced because of leaks. In Ector

Jan 1, 1946

By T. H. Dunn, P. L. Menaul

This paper discusses the results of an investigation made to develop a method of combatting corrosion of subsurface oil-well equipment caused by brines containing hydrogen sulphide. Carbon monoxide, aldehydes, and certain cyanide compounds were found by laboratory tests to effectively inhibit corrosion of steel by sulphide brines. Experiments were made for one year in eight wells in West Texas fields using formaldehyde as an inhibitor. It was found that the inhibitor treatment successfully prevented the severe corrosion previously experienced in these wells, and effected important net savings in operating costs. Introduction Corrosion of oil-field equipment has long been a problem in areas producing sour crudes. These areas include the major fields of Arkansas, Western Kansas, West Texas and New Mexico. Corrosion in these fields is caused primarily by the chemical action of hydrogen sulphide in the presence of water and by electric currents entering the wells through flow lines. Hydrogen sulphide is noncorrosive to iron or steel in the absence of water but under the usual conditions prevailing in oil wells where more or less water is present, hydrogen sulphide is very corrosive. This type of corrosion occurs over the pH range below 9, which includes all natural oil-field brines. If air is present in addition to hydrogen sulphide and water, corrosion proceeds at an extremely rapid rate. It was reported several years ago that a string of oil-well tubing was literally dissolved within 50 days where an air lift was used on a well producing considerable water and hydrogen sulphide. Air is generally absent in wells producing sour crude. After hydrogen sulphide corrosion starts, it proceeds with increasing severity and its correction becomes progressively more difficult. This characteristic of sulphide corrosion has been attributed to the formation of galvanic couples between the iron and steel equipment on one hand and the products of corrosion on the other.' Severe corrosion of subsurface oil-well equipment leads to a multitude of troubles. In addition to destruction of costly equipment, producing sands often are damaged by flooding with water leaking through corroded casing; bad mechanical conditions may develop in a well due to obstructions caused by corroded equipment lost in the hole, or partly collapsed casing; pumping operations are interfered with, and severe emulsification problems may result from the homogenizing action of corroded balls and seats.% A typical case of severe corrosion caused by hydrogen sulphide was reported in Howard County, Texas, where it was necessary to pull tubing once a week to repair leaks after the tubing had been in use for only one year. On one well in this area a string of tubing was pulled 11 times in 8 months; 11 joints of tubing being replaced because of leaks. In Ector

Jan 1, 1946

By I. W. Walling, F. B. Plummer

Bastin and others have demonstrated the presence of sulphate-reducing bacteria in oil wells producing salt water. Analyses show that at 125°F. bacteria alone reduce sulphates in East Texas salt water by only 3 per cent in 30 days, forming principally hydrogen sulphide and sodium or calcium hydroxide. The hydrogen sulphide reacts with soluble iron compounds to produce iron sulphide in the absence of oxygen, and ferric hydroxide where oxygen and air are present. Where iron or other metals and iron sulphide are already in the water containing bacteria, I00 per cent reduction of the sulphates is complete in 30 days or less; where magnesium is present, reduction is complete in 15 days. The effects of changes in temperature, of different bactericides, and of concentration of bactericides on sulphate reduction are described in detail and illustrated by tables and curves. The significance of sulphate reduction on corrosive properties of oil-field water is briefly discussed. Chemistry of East Texas Oil-field Water The chemical composition of the water in the East Texas field salt-water disposal pits is shown in Table I. This salt water corrodes pipes, pumps, and steel tanks excessively, principally because of its content of oxygen, hydrogen, sulphide, and carbonic acid. The carbonates in the water when exposed to air tend to give up carbon dioxide and to precipitate calcium carbonate in large quantities. This forms coatings in tanks, settling pits, and ditches, and soon, unless removed by acid treatment, will effectively clog an injection well and reduce the flow of water back into the ground. The iron compounds in the water, most of which are dissolved from tanks and pipes, are in the ferrous form, and when exposed to the air are oxidized from soluble ferrous carbonate to insoluble ferric hydroxide, resulting in the precipitation of a gelatinous precipitate that will clog oil-field sands effectively: 2Fe(HCO3)2 + O + H2O -> 2Fe(OH)3 + 4CO2 The sulphates in strong sulphate-bearing water may be attacked by swarms of sulphate-reducing bacteria and more hydrogen sulphide may be produced. The hydrogen sulphide reacts with soluble minerals in the water to form black sludges. A knowledge of the chemistry of each reaction in oil-field water is important to the oil-field engineer, since means must be devised to prevent the formation of harmful precipitates that clog injection wells and to prevent corrosion of tanks by harmful products of biochemical processes. Methods of Treating Water before Injection into Ground* The open system of handling the waste salt water in the East Texas field consists of aerating and chemically treating the water to precipitate the unstable iron,

Jan 1, 1946

By F. B. Plummer, I. W. Walling

Bastin and others have demonstrated the presence of sulphate-reducing bacteria in oil wells producing salt water. Analyses show that at 125°F. bacteria alone reduce sulphates in East Texas salt water by only 3 per cent in 30 days, forming principally hydrogen sulphide and sodium or calcium hydroxide. The hydrogen sulphide reacts with soluble iron compounds to produce iron sulphide in the absence of oxygen, and ferric hydroxide where oxygen and air are present. Where iron or other metals and iron sulphide are already in the water containing bacteria, I00 per cent reduction of the sulphates is complete in 30 days or less; where magnesium is present, reduction is complete in 15 days. The effects of changes in temperature, of different bactericides, and of concentration of bactericides on sulphate reduction are described in detail and illustrated by tables and curves. The significance of sulphate reduction on corrosive properties of oil-field water is briefly discussed. Chemistry of East Texas Oil-field Water The chemical composition of the water in the East Texas field salt-water disposal pits is shown in Table I. This salt water corrodes pipes, pumps, and steel tanks excessively, principally because of its content of oxygen, hydrogen, sulphide, and carbonic acid. The carbonates in the water when exposed to air tend to give up carbon dioxide and to precipitate calcium carbonate in large quantities. This forms coatings in tanks, settling pits, and ditches, and soon, unless removed by acid treatment, will effectively clog an injection well and reduce the flow of water back into the ground. The iron compounds in the water, most of which are dissolved from tanks and pipes, are in the ferrous form, and when exposed to the air are oxidized from soluble ferrous carbonate to insoluble ferric hydroxide, resulting in the precipitation of a gelatinous precipitate that will clog oil-field sands effectively: 2Fe(HCO3)2 + O + H2O -> 2Fe(OH)3 + 4CO2 The sulphates in strong sulphate-bearing water may be attacked by swarms of sulphate-reducing bacteria and more hydrogen sulphide may be produced. The hydrogen sulphide reacts with soluble minerals in the water to form black sludges. A knowledge of the chemistry of each reaction in oil-field water is important to the oil-field engineer, since means must be devised to prevent the formation of harmful precipitates that clog injection wells and to prevent corrosion of tanks by harmful products of biochemical processes. Methods of Treating Water before Injection into Ground* The open system of handling the waste salt water in the East Texas field consists of aerating and chemically treating the water to precipitate the unstable iron,

Jan 1, 1946

By Willis R. Battles, William F. Cerini, P. H. Jones

A test for determining the plugging characteristics of an oil-well injection water has been developed. It consists in measuring changes of the filter rate of a water at constant pressure with cumulative throughput when passing the water through a medium grade sintered glass disk. Application of the test method was made to the water used in the Union Oil Company's experimental water flood of the Chapman zone in the Richfield field, Orange County, Callfornia. This water developed increasing plugging tendencies upon aging, even though the finished water from the plant filter exhibited few such characteristics. The plugging material was found to consist of calcium carbonate, ferric hydroxide, and organic substances that were presumed to be bacterial. Various method of stabilizing this water to prevent the formation of plugging material were attempted. Lowering the pH to approximately 6.4 by injecting carbon dioxide provided a moderately satisfactory means for stabilization but a better method of stabilizing this water was found to be first aging and then filtering. Introduction An experimental water-flood project was started on the Chapman zone of the Richfield field in March 1944 and has been described in a previous paper.' It consists of a single injection well drilled between old producing wells. A water-treating plant using primary alum flocculation, sedimentation and chlorination followed by secondary flocculation, sedimentation and fltration is employed to process the water before in@ion. In all of the water-treating operations, the system is open to the air, and no attempt is made to prevent the loss of carbon dioxide or absorption of oxygen by the water. The clear water is stored in a covered concrete basin and pumped through a Transite line to the suction of a high-pressure pump at the injection well' The high-pressure tubing in the well to the injection zone is cement lined. The untreated injection water is a mixture produced with the oil from the Chapman and Kraemer zones and is supplied from the disposal system. Because the injection well was relatively deep (injection zone about 3400 ft.) and would be expensive to replace, it was believed imperative to supply a nonplug-ging injection water and to develop laboratory procedures for evaluating the treated injection water with respect to its formation plugging properties. This report describes the development and application of the test procedure based on the assumption that the plugging properties could be determined by measuring the progressive decrease in flow rate of the water through a porous medium. If the quality of the injection water was good enough so that the plugging action on the porous medium was of small magnitude, it was reasoned that the tendency to impair flow in the formation would not be serious.

Jan 1, 1946

By William F. Cerini, Willis R. Battles, P. H. Jones

A test for determining the plugging characteristics of an oil-well injection water has been developed. It consists in measuring changes of the filter rate of a water at constant pressure with cumulative throughput when passing the water through a medium grade sintered glass disk. Application of the test method was made to the water used in the Union Oil Company's experimental water flood of the Chapman zone in the Richfield field, Orange County, Callfornia. This water developed increasing plugging tendencies upon aging, even though the finished water from the plant filter exhibited few such characteristics. The plugging material was found to consist of calcium carbonate, ferric hydroxide, and organic substances that were presumed to be bacterial. Various method of stabilizing this water to prevent the formation of plugging material were attempted. Lowering the pH to approximately 6.4 by injecting carbon dioxide provided a moderately satisfactory means for stabilization but a better method of stabilizing this water was found to be first aging and then filtering. Introduction An experimental water-flood project was started on the Chapman zone of the Richfield field in March 1944 and has been described in a previous paper.' It consists of a single injection well drilled between old producing wells. A water-treating plant using primary alum flocculation, sedimentation and chlorination followed by secondary flocculation, sedimentation and fltration is employed to process the water before in@ion. In all of the water-treating operations, the system is open to the air, and no attempt is made to prevent the loss of carbon dioxide or absorption of oxygen by the water. The clear water is stored in a covered concrete basin and pumped through a Transite line to the suction of a high-pressure pump at the injection well' The high-pressure tubing in the well to the injection zone is cement lined. The untreated injection water is a mixture produced with the oil from the Chapman and Kraemer zones and is supplied from the disposal system. Because the injection well was relatively deep (injection zone about 3400 ft.) and would be expensive to replace, it was believed imperative to supply a nonplug-ging injection water and to develop laboratory procedures for evaluating the treated injection water with respect to its formation plugging properties. This report describes the development and application of the test procedure based on the assumption that the plugging properties could be determined by measuring the progressive decrease in flow rate of the water through a porous medium. If the quality of the injection water was good enough so that the plugging action on the porous medium was of small magnitude, it was reasoned that the tendency to impair flow in the formation would not be serious.

Jan 1, 1946

By Carlton Beal

This paper presents useful charts for conversion of various viscosimeter units into centipoises and graphically summarizes published investigations of the viscosity of air, water and natural gas at high temperatures and pressures. Where possible, charts and correlations were constructed to cover a range of temperature (60°F. to 300°F.) and pressure (14.7 lb. per sq. in. abs. to 8000 lb. per sq. in. gauge) encountered in oil fields. Correlation charts, for the purpose of predicting crude oil viscosity and solubility behavior at oil field temperatures and pressures, were constructed from an analysis and correlation of 1332 viscosity and solubility observations from 953 crude oil samples taken from 747 oil fields. Of these fields, 501 are in the United States, including 75 in California. Of the 1332 observations, 1215 were viscosity values, including 786 of gas-free crude oil, 351 of oil saturated with gas, and 78 under-saturated with gas at pressures above the bubble point. Results show that crude oil viscosity at various reservoir conditions can be predicted with average deviations varying from 24.2 per cent for gas-free crude oil to as little as 2.7 per cent for undersaturated crude oil "above the bubble point." The solubility of crude oil may be predicted from oil gravity and saturation pressure with an average deviation of 22.0 per cent from observed values. In conclusion, it is shown that the viscosity of a gas and gas-saturated crude oil may be predicted within the accuracy of most reservoir computations. Viscosity is a measure of flow resistance; common units are in centipoises (cp.). The object of this report is to present conversion charts and simplified 'correlation charts showing the viscosity behavior of air, water, gas and crude oil and gas-saturated crude oil under oil field temperatures and pressures, which have been known to be as high as 300°F. and 8000 Ib. per sq. in. gauge under subsurface conditions. The viscosity of a liquid or gas is important because it is a measure of its fluidity, or its ability to flow through pipe lines or oil sands. Viscosity of air has become important because it is being used in secondaryl,2 recovery projects. The viscosity of natural gas and water at reservoir conditions is useful because they are almost universally associated and produced with crude oil. The viscosity of gas-saturated crude oil at reservoir pressures and tem peratures is of particular value in making estimates of oil reserves3 and rate of oil recovery from flush pools when production decline data are limited. Instruments Used to MeasuRe Viscosity There are many types of viscosimeters,4 and the instruments most commonly used to measure the atmospheric viscosity of liquids at moderate temperatures and their practical working ranges have been deScribed5,6 in detail. Fig. I and Fig. 2 are viscosity conversion charts which have

Jan 1, 1946

By Carlton Beal

This paper presents useful charts for conversion of various viscosimeter units into centipoises and graphically summarizes published investigations of the viscosity of air, water and natural gas at high temperatures and pressures. Where possible, charts and correlations were constructed to cover a range of temperature (60°F. to 300°F.) and pressure (14.7 lb. per sq. in. abs. to 8000 lb. per sq. in. gauge) encountered in oil fields. Correlation charts, for the purpose of predicting crude oil viscosity and solubility behavior at oil field temperatures and pressures, were constructed from an analysis and correlation of 1332 viscosity and solubility observations from 953 crude oil samples taken from 747 oil fields. Of these fields, 501 are in the United States, including 75 in California. Of the 1332 observations, 1215 were viscosity values, including 786 of gas-free crude oil, 351 of oil saturated with gas, and 78 under-saturated with gas at pressures above the bubble point. Results show that crude oil viscosity at various reservoir conditions can be predicted with average deviations varying from 24.2 per cent for gas-free crude oil to as little as 2.7 per cent for undersaturated crude oil "above the bubble point." The solubility of crude oil may be predicted from oil gravity and saturation pressure with an average deviation of 22.0 per cent from observed values. In conclusion, it is shown that the viscosity of a gas and gas-saturated crude oil may be predicted within the accuracy of most reservoir computations. Viscosity is a measure of flow resistance; common units are in centipoises (cp.). The object of this report is to present conversion charts and simplified 'correlation charts showing the viscosity behavior of air, water, gas and crude oil and gas-saturated crude oil under oil field temperatures and pressures, which have been known to be as high as 300°F. and 8000 Ib. per sq. in. gauge under subsurface conditions. The viscosity of a liquid or gas is important because it is a measure of its fluidity, or its ability to flow through pipe lines or oil sands. Viscosity of air has become important because it is being used in secondaryl,2 recovery projects. The viscosity of natural gas and water at reservoir conditions is useful because they are almost universally associated and produced with crude oil. The viscosity of gas-saturated crude oil at reservoir pressures and tem peratures is of particular value in making estimates of oil reserves3 and rate of oil recovery from flush pools when production decline data are limited. Instruments Used to MeasuRe Viscosity There are many types of viscosimeters,4 and the instruments most commonly used to measure the atmospheric viscosity of liquids at moderate temperatures and their practical working ranges have been deScribed5,6 in detail. Fig. I and Fig. 2 are viscosity conversion charts which have

Jan 1, 1946

By R. H. Olds, B. H. Sage

The formation volume and volume of the liquid phase of oil and gas obtained from four fields in the San Joaquin Valley have been investigated at pressures, temperature, and gas-oil ratios comparable to those encountered in underground reservoirs. All the fields covered in this investigation yielded a product of a gas-oil ratio in excess of 5000 cu ft per barrel and the gravity of the tank oil for the four fields in question varied between 52° and 63' API. The results of the investigation, together with analytical data concerning the composition of the oil and gas, are submitted in tabular form. Rough correlations of the formation volume as a function of pressure, temperature, and gas-oil ratio and of the retrograde dew-point pressure as a function of gas-oil ratio, temperature, and gravity of tank oil are presented. It was not found feasible to correlate simply the formation volume of the liquid phase as a function of the applicable variable. It is desired to emphasize that these correlations are considered applicable only to the range of conditions covered in this investigation and for systems of similar nature and composition. Introduction Information concerning the physical properties of mixtures of oil and gas from particular fields have often been employed in predicting the situations obtaining in underground reservoirs. One of the earlier studies of this nature was the work of Beecher and Parkhurst,1 while a more recent study of the Dominguez Field2 presented detailed volumetric data in the two-phase as well as in the single-phase regions. Although these studies were confined to individual fields, their results proved of value in application to other fields. It has recently been shown 3,4 that it is possible in the region of low gas-oil ratios* to correlate the volumetric behavior of naturally occurring hydrocarbon mixtures from a single geographical area with sufficient accuracy to be of industrial value. For this reason it is considered of interest to submit information concerning the volumetric behavior of oil and gas mixtures from four different fields in the San Joaquin Valley and, in combination with similar published data5 concerning mixtures of oil and gas from the Paloma field in the same area, to show rough correlations between the composition and the behavior of materials from these fields. This effort seems particularly worth while since all of the

Jan 1, 1947

By R. H. Olds, B. H. Sage

The formation volume and volume of the liquid phase of oil and gas obtained from four fields in the San Joaquin Valley have been investigated at pressures, temperature, and gas-oil ratios comparable to those encountered in underground reservoirs. All the fields covered in this investigation yielded a product of a gas-oil ratio in excess of 5000 cu ft per barrel and the gravity of the tank oil for the four fields in question varied between 52° and 63' API. The results of the investigation, together with analytical data concerning the composition of the oil and gas, are submitted in tabular form. Rough correlations of the formation volume as a function of pressure, temperature, and gas-oil ratio and of the retrograde dew-point pressure as a function of gas-oil ratio, temperature, and gravity of tank oil are presented. It was not found feasible to correlate simply the formation volume of the liquid phase as a function of the applicable variable. It is desired to emphasize that these correlations are considered applicable only to the range of conditions covered in this investigation and for systems of similar nature and composition. Introduction Information concerning the physical properties of mixtures of oil and gas from particular fields have often been employed in predicting the situations obtaining in underground reservoirs. One of the earlier studies of this nature was the work of Beecher and Parkhurst,1 while a more recent study of the Dominguez Field2 presented detailed volumetric data in the two-phase as well as in the single-phase regions. Although these studies were confined to individual fields, their results proved of value in application to other fields. It has recently been shown 3,4 that it is possible in the region of low gas-oil ratios* to correlate the volumetric behavior of naturally occurring hydrocarbon mixtures from a single geographical area with sufficient accuracy to be of industrial value. For this reason it is considered of interest to submit information concerning the volumetric behavior of oil and gas mixtures from four different fields in the San Joaquin Valley and, in combination with similar published data5 concerning mixtures of oil and gas from the Paloma field in the same area, to show rough correlations between the composition and the behavior of materials from these fields. This effort seems particularly worth while since all of the

Jan 1, 1947

By P. H. Delano, Will H. Coghill, G. D. Coe

Data concerning the actual net energy required for pulverizing coal are lacking from the literature on coal pulverization. Power data given in the literature concern gross power and frequently include the power expended on the air blast or product-conveyor system, as well as power lost through friction in the pulverizer itself. Consequently, such data supply no information regarding the net energy consumed in pulverizing or the relative grinding resistance of various coals. In the study of coal pulverizing much work has been done on what is known as " grindability-index numbers," but grind-ability tests have seldom considered the energy input (that is, the "cause" part of the system "cause and effect"). There are many records of the effect, but even these have questionable value because the "grindability" tests did not make a pull'erized product by a method comparabLe with- commercial pulverizers. In many of the tests, only a selected part of the coal was ground, and the remainder continued to be an unknown factor. Furthermore, none of the grindability tests provide the balanced circulating load common to all modern commercial pulverizing. In order to obtain better understanding of the fundamental principles of coal pulvcrizing, the Bureau of Mines is investigating the "cause" phase; that is, the net energy input or net power excluding friction between the moving parts of the machine. As a first step in the investigation,it was necessary to design and construct a laboratory machine in which no friction-loss corrections are involved, which could grind and finish a minus-¾-inch feed, which could be emptied rapidly and completely, which could operate with a continuous feed and finish in an air separator; and, most essential of all, which would be equipped with a measuring device for recording only that portion of the total power consumed in actual pulverizing, hereafter referred to as "net energy input" or "net horsepower-hours." The channel-roller pulverizer hereinafter described is believed to meet these requirements. History oF the Machine The, work started when Ralph W. smith, engineer, St. Genevieve Lime Co., St. Cenevieve, Mo., was appointed one of the consultants of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, to develop a machine for testing the abrasiveness of coal. Smith had already developed a machine for testing the abrasive-ness of dentifrices,1 and it was thought the same principles might be applied to coal, Smith's machine had a revolving disk with an annular channel in which the sample was placed. Riding in the channel was a small block or runner of selected soft metal held

Jan 1, 1942

By Will H. Coghill, P. H. Delano, G. D. Coe

Data concerning the actual net energy required for pulverizing coal are lacking from the literature on coal pulverization. Power data given in the literature concern gross power and frequently include the power expended on the air blast or product-conveyor system, as well as power lost through friction in the pulverizer itself. Consequently, such data supply no information regarding the net energy consumed in pulverizing or the relative grinding resistance of various coals. In the study of coal pulverizing much work has been done on what is known as " grindability-index numbers," but grind-ability tests have seldom considered the energy input (that is, the "cause" part of the system "cause and effect"). There are many records of the effect, but even these have questionable value because the "grindability" tests did not make a pull'erized product by a method comparabLe with- commercial pulverizers. In many of the tests, only a selected part of the coal was ground, and the remainder continued to be an unknown factor. Furthermore, none of the grindability tests provide the balanced circulating load common to all modern commercial pulverizing. In order to obtain better understanding of the fundamental principles of coal pulvcrizing, the Bureau of Mines is investigating the "cause" phase; that is, the net energy input or net power excluding friction between the moving parts of the machine. As a first step in the investigation,it was necessary to design and construct a laboratory machine in which no friction-loss corrections are involved, which could grind and finish a minus-¾-inch feed, which could be emptied rapidly and completely, which could operate with a continuous feed and finish in an air separator; and, most essential of all, which would be equipped with a measuring device for recording only that portion of the total power consumed in actual pulverizing, hereafter referred to as "net energy input" or "net horsepower-hours." The channel-roller pulverizer hereinafter described is believed to meet these requirements. History oF the Machine The, work started when Ralph W. smith, engineer, St. Genevieve Lime Co., St. Cenevieve, Mo., was appointed one of the consultants of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, to develop a machine for testing the abrasiveness of coal. Smith had already developed a machine for testing the abrasive-ness of dentifrices,1 and it was thought the same principles might be applied to coal, Smith's machine had a revolving disk with an annular channel in which the sample was placed. Riding in the channel was a small block or runner of selected soft metal held

Jan 1, 1942

By E. S. Grumell

The correct sampling of coal and coke is becoming important to an ever increasing number of producers and consumers. This, therefore, may be an opportune moment to examine where we stand with regard to existing and proposed methods. In this paper an attempt will be made to review, as briefly as possible, some of the considerable amount of painstaking research which has been done in the last 10 years, and which has unquestionably led to a much better understanding of the subject. In so doing we shall try, on the one hand, to make clear where substantial progress has been made, and on the other hand, to draw attention to points that require further investigation. The paper is divided into sections in order to emphasize the major divisions of the subject; further, in order to retain this emphasis, detailed consideration of some of the points has been relegated to appendixes. No attempt has been made to give a complete survey of the literature, as this has already been done by L. A. Bushell.2 The following abbreviations will be used: A.E., average error; P.E., probable error; S.W.R., size-weight ratio; B.S.I., British Standards Institution. Section 1.—Cost It has often been stated that the cost of sampling should bear some relationship to the value of the product, and since coal is a relatively cheap raw material it would be a major error to specify, for ordinary commercial purposes, elaborate and costly methods of sampling which nobody would adopt. Specifications must be of such a nature that they will be used. We believe that one of the achievements of the last 10 years has been to reduce the cost of sampling. There is, however, another point to be considered; via., that the cost of sampling should bear some relationship to the value of the investigation. Correct sampling is a cog (possibly a small one) in the wheel

Jan 1, 1940

By E. S. Grumell

The correct sampling of coal and coke is becoming important to an ever increasing number of producers and consumers. This, therefore, may be an opportune moment to examine where we stand with regard to existing and proposed methods. In this paper an attempt will be made to review, as briefly as possible, some of the considerable amount of painstaking research which has been done in the last 10 years, and which has unquestionably led to a much better understanding of the subject. In so doing we shall try, on the one hand, to make clear where substantial progress has been made, and on the other hand, to draw attention to points that require further investigation. The paper is divided into sections in order to emphasize the major divisions of the subject; further, in order to retain this emphasis, detailed consideration of some of the points has been relegated to appendixes. No attempt has been made to give a complete survey of the literature, as this has already been done by L. A. Bushell.2 The following abbreviations will be used: A.E., average error; P.E., probable error; S.W.R., size-weight ratio; B.S.I., British Standards Institution. Section 1.—Cost It has often been stated that the cost of sampling should bear some relationship to the value of the product, and since coal is a relatively cheap raw material it would be a major error to specify, for ordinary commercial purposes, elaborate and costly methods of sampling which nobody would adopt. Specifications must be of such a nature that they will be used. We believe that one of the achievements of the last 10 years has been to reduce the cost of sampling. There is, however, another point to be considered; via., that the cost of sampling should bear some relationship to the value of the investigation. Correct sampling is a cog (possibly a small one) in the wheel

Jan 1, 1940

By H. T. Clark, H. K. Work

The instrument for the rapid determination of carbon in steel, described in this paper, was developed originally to facilitate the operation of the pilot-sized open-hearth furnace in the Jones & Laughlin Research and Eevelopment Laboratory. In this small furnace, with its shallow bath, the drop in carbon is accelerated, and a rapid, reliable test for carbon content is indispensable. This problem becomes rather acute when it is desired to finish heats at a carbon content higher than can be estimated with any degree of accuracy by the fracture test. Several independent methods for determining carbon were investigated, therefore, and it was found that a relatively simple magnetic device could be made to give reproducible results. A laboratory instrument was designed and set up for the use of the furnace operators. It was tested exhaustively in the laboratory and was used with considerable success for following the carbon content in the furnace bath. As soon as sufficient data had been compiled to indicate that the instrument might have a wider application, a more rugged model was constructed and placed in the mill to be tested on commercial heats. Finally, about a year ago, instruments were furnished to the plant open-hearth shops, and these have been in use since that time. As a matter of convenience, the instrument has been named the "Carbanalyzer," and will be referred to by this designation in the following pages. $ Eaklier Investigations While by far the greatest number of magnetic investigations in which the carbon content of ferromagnetic materials was considered have had to do with the evaluation of the magnetic properties of steels of known

Jan 1, 1940

By H. K. Work, H. T. Clark

The instrument for the rapid determination of carbon in steel, described in this paper, was developed originally to facilitate the operation of the pilot-sized open-hearth furnace in the Jones & Laughlin Research and Eevelopment Laboratory. In this small furnace, with its shallow bath, the drop in carbon is accelerated, and a rapid, reliable test for carbon content is indispensable. This problem becomes rather acute when it is desired to finish heats at a carbon content higher than can be estimated with any degree of accuracy by the fracture test. Several independent methods for determining carbon were investigated, therefore, and it was found that a relatively simple magnetic device could be made to give reproducible results. A laboratory instrument was designed and set up for the use of the furnace operators. It was tested exhaustively in the laboratory and was used with considerable success for following the carbon content in the furnace bath. As soon as sufficient data had been compiled to indicate that the instrument might have a wider application, a more rugged model was constructed and placed in the mill to be tested on commercial heats. Finally, about a year ago, instruments were furnished to the plant open-hearth shops, and these have been in use since that time. As a matter of convenience, the instrument has been named the "Carbanalyzer," and will be referred to by this designation in the following pages. $ Eaklier Investigations While by far the greatest number of magnetic investigations in which the carbon content of ferromagnetic materials was considered have had to do with the evaluation of the magnetic properties of steels of known

Jan 1, 1940