Search Documents

By C.P. Proctor, J. T. Crawford, J.A. Younkins

Coal-cleaning plants using the launder process generally wash the fine coal (minus ? or minus 5/16-in.) separately in a plant consisting of washing launders or troughs placed one below another and sometimes supplemented by additional washing equipment such as tables and jigs. The coal and its associated impurities enter the feed end of the top launder, with a current of push water. As the material moves along the impurities, being heavier than coal, settle toward the bottom of the launder and are drawn off, with some coal, through "free discharge" boxes to the launder below. These boxes were given their name because their discharge falls freely; that is, it does not discharge into a water seal. Thus the impurities are progressively concentrated in the lower launders until box products are sufficiently free of coal to be discharged to refuse. The overflows of the upper launders go to clean coal while the overflow of the lowest launder, and perhaps that of the one immediately above, is usually recirculated to the plant feed. Thus the bulk of the clean coal is removed rapidly and the impurities are concentrated more slowly. The chief purpose of this paper is to present the cleaning data of such a plant under different operating conditions. OpeRating Equipment The washing units considered here are part of a complete plant cleaning minus 4-in. coal. The primary cleaned product is a high-quality gas and metallurgical coal and another portion of the output may be shipped as a steam coal. The units consist of two parallel Rheolaveur free-discharge units each containing five launders, together with three 7 by 14-ft. Plato tables. The launders are designated by the letters A-B-C-D-E (Fig. I), launder A being the top and longest; E being the bottom and shortest. Launder details are given in Table 1. The launders are equipped with a series of free-discharge Rheolaveur boxes, which are integral parts of the launder (Figs. 2 and 3). Each box with-

Jan 1, 1940

By C. P. Proctor, J. A. Younkins, J. T. Crawford

Coal-cleaning plants using the launder process generally wash the fine coal (minus ? or minus 5/16-in.) separately in a plant consisting of washing launders or troughs placed one below another and sometimes supplemented by additional washing equipment such as tables and jigs. The coal and its associated impurities enter the feed end of the top launder, with a current of push water. As the material moves along the impurities, being heavier than coal, settle toward the bottom of the launder and are drawn off, with some coal, through "free discharge" boxes to the launder below. These boxes were given their name because their discharge falls freely; that is, it does not discharge into a water seal. Thus the impurities are progressively concentrated in the lower launders until box products are sufficiently free of coal to be discharged to refuse. The overflows of the upper launders go to clean coal while the overflow of the lowest launder, and perhaps that of the one immediately above, is usually recirculated to the plant feed. Thus the bulk of the clean coal is removed rapidly and the impurities are concentrated more slowly. The chief purpose of this paper is to present the cleaning data of such a plant under different operating conditions. OpeRating Equipment The washing units considered here are part of a complete plant cleaning minus 4-in. coal. The primary cleaned product is a high-quality gas and metallurgical coal and another portion of the output may be shipped as a steam coal. The units consist of two parallel Rheolaveur free-discharge units each containing five launders, together with three 7 by 14-ft. Plato tables. The launders are designated by the letters A-B-C-D-E (Fig. I), launder A being the top and longest; E being the bottom and shortest. Launder details are given in Table 1. The launders are equipped with a series of free-discharge Rheolaveur boxes, which are integral parts of the launder (Figs. 2 and 3). Each box with-

Jan 1, 1940

By Harold A. Linke

The following article presents notes and data compiled and computed by the writer for use in the determination of: size and slope of mill launders, details of junction boxes and downspouts, and distribution of pulp. It also includes pulp formulas, volume of discharge through bushings, paths of discharging streams, banking of turns and curves. In the design of a concentrating mill, the draftsman usually considers launders to the extent of providing ample "head" for transmission of pulp from one department of the mill to another. The superintendent of construction aims to build his launders wide and deep, and on a slope steep enough to ensure positive flow. So launders are laid generally on too steep a slope, with the result that the repair gang works to maintain launder bottoms and sides against the erosive action of the conveyed pulp. To this end many kinds of liners have been devised: concrete, mastic, white iron, glass, rubber. True, the reduction of slope to the point where a pulp will flow with minimum wear, will minimize labor and expense; but when the desired slope is not predetermined, the millman hesitates to readjust his launder slopes by cut-and-try methods. To the end that the desired size and slope may be found readily, the writer has: (1) conducted experiments with pulps of different specific gravity, screen analysis and dilution; (2) gathered a few graphic data from standard reference works (such as Peele's Mining Engineer's Handbook and Taggart's Handbook of Ore Dressing); (3) computed several tables; and compiled results that have proved dependable for Utah Copper ore. It is quite possible that the following tables and graphs may not be applicable to all ores, but it is hoped that they may prove helpful, even in slight degree, in alleviating a portion of the trouble and migraine of some other millman. Launder Slopes The main object in the study of launder slopes is to provide grade steep enough to prevent "sanding" by a safe margin, and to avoid

Jan 1, 1943

By Harold A. Linke

The following article presents notes and data compiled and computed by the writer for use in the determination of: size and slope of mill launders, details of junction boxes and downspouts, and distribution of pulp. It also includes pulp formulas, volume of discharge through bushings, paths of discharging streams, banking of turns and curves. In the design of a concentrating mill, the draftsman usually considers launders to the extent of providing ample "head" for transmission of pulp from one department of the mill to another. The superintendent of construction aims to build his launders wide and deep, and on a slope steep enough to ensure positive flow. So launders are laid generally on too steep a slope, with the result that the repair gang works to maintain launder bottoms and sides against the erosive action of the conveyed pulp. To this end many kinds of liners have been devised: concrete, mastic, white iron, glass, rubber. True, the reduction of slope to the point where a pulp will flow with minimum wear, will minimize labor and expense; but when the desired slope is not predetermined, the millman hesitates to readjust his launder slopes by cut-and-try methods. To the end that the desired size and slope may be found readily, the writer has: (1) conducted experiments with pulps of different specific gravity, screen analysis and dilution; (2) gathered a few graphic data from standard reference works (such as Peele's Mining Engineer's Handbook and Taggart's Handbook of Ore Dressing); (3) computed several tables; and compiled results that have proved dependable for Utah Copper ore. It is quite possible that the following tables and graphs may not be applicable to all ores, but it is hoped that they may prove helpful, even in slight degree, in alleviating a portion of the trouble and migraine of some other millman. Launder Slopes The main object in the study of launder slopes is to provide grade steep enough to prevent "sanding" by a safe margin, and to avoid

Jan 1, 1943

By F. N. Koepel, L. A. Callaway

The property of the Andes Copper Mining Co. is in the central part of the Republic of Chile, Province of Atacama, about 75 miles to the eastward from the port of Chafñaral. At this point the Andean system is made up of two principal ranges, and the mine and metallurgical plant are both on the westerly slope of the outer or western range. Mean elevation of the mine is 10,500 ft., while at the plant the elevation ranges from 9445 to 9700 ft. A meter gage railroad extends from the company's port at Barquito, near Chañaral, to the reduction plant at Potrerillos. This road has a total length of 94 miles, of which 57.79 miles are owned by the Andes Copper Mining Co. and the remainder of the road is controlled by the State. Development of the Potrerillos mine and installation of the metallurgical equipment presented unusual difficulties due to the arid nature of the country, high altitude and remoteness of the location from any considerable center of population. As a primary step it was necessary that railroad transportation be provided in order that mine development and plant construction could go forward on an economical basis. Provision of an adequate supply of water for domestic and metallurgical uses involved the construction of approximately 178 miles of pipe lines, all of which have their sources at altitudes ranging from 12,000 to 14,000 ft. above sea level and traverse rough and difficult terrane. Water for metallurgical use is brought to Potrerillos from the Ola River, a stream originating in the high cordillera to the eastward from the property. It is delivered by means of a steel pipe line, 32 miles long, having diameters ranging from 22 to 36 in. Domestic water is supplied to the various camps through a system of pipe lines aggregating 146 miles in length, the Ola water being unfit for this purpose. These conductors gather water from numerous springs in the high mountains to the eastward from Potrerillos and deliver it to the mine, the reduction works and the port at Barquito. Extensive permanent housing facilities had to be provided as it was necessary to care for more than 3000 workmen and employees at the

Jan 1, 1934

By G. U. Greene

The various lead producers have given the subject of lead drosses much attention in recent years but the problem of their economical treatment is yet to be solved. Formerly the copper in the furnace feed was removed from the furnace in the form of matte. The speiss at that time consisted principally of the iron arsenide. The practice today is to roast off most of the sulphur and the copper in the feed forms a dross in the furnace, which is removed from the furnace with the lead. This material is poured into the drossing kettles and allowed to cool down to but slightly above the freezing point of lead. The copper dross, containing almost all of the arsenic and part of the antimony, is skimmed off and treated in a small reverberatory furnace at most plants. This is essentially a liquation process. The skimmed dross contains from 70 to 80 per cent lead, and much of this lead is liquated out. The products from this treatment are: (1) impure lead, (2) speiss and (3) matte. The speiss from the reverberatory furnace was studied in this research. The literature on the subject is of very little assistance, as almost no work has been done on the problem of establishing the exact identity of the various phases present. One author(1)† states that speiss consists of a series of isomorphous compounds of the general formula FexAsy in which the Fe may be replaced by Ni, Co, Cu, Pb, Ag, Au, Pt, Zn, Cd and the As replaced by Sb, S and Bi. Hofman(2) states that the iron arsenide present is Fe5As. Experimental Work In the present research, the author used for methods in an attempt to determine the composition of the various phases: (1) chemical, (2) microscopic, (3) roentgenographic and (4) thermal. Previous to this research, considerable time had been spent making analyses of different speisses, but unfortunately no very definite conclusions could be made as a result of these analyses.

Jan 1, 1937

By T. E. Harper, Gustave Reinberg

Electrolytic refining of all lead bullion produced at the Oroya smelter of the Cerro de Pasco Copper Corporation has been adopted as standard practice. A pilot refinery with a capacity of 25 metric tons daily has been in operation since June, 1934, and a new refining unit having an initial capacity of 100 tons per day is under construction. This program has been made possible by certain modifications of the usual Betts refining process1, developed at Oroya, which have the effect of making the purity of the lead produced, and the acid loss incurred in operating the process, entirely independent of the amount of impurities in the original bullion. The modified process, as developed and at present used, treats impure bullion direct, without presoftening or other prerefining step, except that if the bullion carries tin it is desirable to detin before casting into anodes, since tin carries over to some extent to the cathodes. The refining process developed differs from usual Betts practice in two essential particulars: the anodes are cast thinner and replaced at more frequent intervals, and anode slimes are washed by a system of counter-current dipping, prior to their removal from the surface of the anode scrap. Limiting the period of anode corrosion insures a cathode of high purity, since solution of impurities at the anode can occur only if the thickness of the anode slime blanket, and hence the voltage drop across it, becomes greater than a certain critical value. The dip washing system operates to prevent acid losses, by recovering the highly concentrated, nearly neutral lead fluosilicate solution present in the pores of the slime blanket on the corroded anode, and doing this in such a way that there is no opportunity for chemical decomposition to occur. The best illustration of the efficacy of these two expedients may be secured from records of more than a year's operation of the 25-ton pilot plant, during which period the acid losses were less than 2 Ib. of 100 per cent hydrofluosilic acid (H2SiF6) per ton of lead produced, and typical assays of bullion and refined lead were as shown in Table 1.

Jan 1, 1937

By H. E. Lee, P. C. Feddersen

Blast-fuRnace operation at the Bunker Hill smelter deviates somewhat from common practice. Under existing conditions it is economical to operate the furnaces at "forced" capacity. The furnace feed consists chiefly of sinter and averages close to 50 per cent lead. Experience in smelting such material favors a low charge column attended by smaller proportions of coke and a low blast pressure. Under such conditions the gain in furnace tonnage greatly overbalances the somewhat higher slag losses and increased percentage of material fumed Furnace Charge The ingredients for the blast-furnace feed are stored in a group of 24 charge bins (3600 cu. ft. capacity). Each bin has two discharge chutes. Beneath each chute is a steel weighing hopper, suspended from a Fairbanks scale. The several hoppers are kept filled with the exact amount of material required to complete a furnace charge. The weighed material is discharged into a standard-gauge, bottom-dump charge car containing two compartments, each of which holds a complete charge (approximately 1½ tons). It is hauled to the blast furnace by a 44011 electric trolley locomotive. The proportionate parts of the various constituents of a representative blast-furnace charge are shown in Table 1. Table 1.—Representative Blast-furnace Charge at Bunker Hill Smelter Material Pounds Sinter.................................................. 2500 Limerock............................................... 0- 50 Coke................................................. 250-300 Scrap iron.............................................. 0-25 Settler skulls.......................................... 75 Undried zinc-plant residue................................ 0-200 Siliceous ore............................................ 25 Baghouse dust.......................................... 0-50 By-product slag......................................... 100 A variable stock tonnage of zinc-plant residue and return by-products results in fluctuations in the percentages of these materials in the blastfurnace feed. Accompanying such variations are corresponding increases or decreases in the amounts of coke, limerock and scrap iron necessary to obtain good furnace operation and adequate reduction.

Jan 1, 1937

By Jesse O. Betterton

In the Parkes process of lead refining, after desilverization has been completed by means of zinc additions, there will remain in the lead from 0.5 to 0.6 per cent zinc. At this stage in the refining practically all impurities are reduced to refined lead specifications except zinc and antimony. All excess of copper and nearly all the arsenic goes out with the silver. Silver remaining should not exceed 0.1 oz. per ton. It thus remains only to remove zinc and antimony to produce refined lead. The older practice was to complete refining by means of oxidation processes in reverberatory furnaces. Essentially this consisted of heating the lead to 1200' to 1300" I?. and allowing it to come in contact with a considerable excess of air passing through the furnace, or accomplish the same result by blowing the lead with steam by means of pipes introduced for that purpose, at the same time allowing air to enter the furnace. Usually some procedure involving alternate oxidation and reduction with fine coal or coke was employed in order to reduce the weight of dross or skim finally removed from the furnace. This practice had many elements of weakness in that the main flour of lead, after the preceding expensive operations had been performed, and the whole refining process nearly completed, was subjected to an operation at a comparatively high temperature, which involved much lead loss if the furnaces were not on bags, and the production of 3 to 5 per cent of the weight of the lead as dross or skim, which had to be resmelted and the lead either refined or produced as antimonial lead. In addition, the operating expense of the process was a considerable item. The process of dezincing with chlorine was developed as a substitute for the foregoing described oxidation process, and finally resulted in such advantages as nearly equal operating costs, a practical elimination of the lead loss, and the direct production of a very valuable byproduct, zinc chloride, that may be sold as such or retreated for its zinc and chlorine contents, both of which can be reused in the refining processes. Essentially this process consists of circulating the lead by means of a pump in a kettle through a closed reaction cylinder, gaseous chlorine entering the reaction cylinder with the stream of lead from the pump. Molten zinc chloride is thus produced and is discharged together with

Jan 1, 1937

By G. L. Oldright, T. B. Brighton, C. M. Dice

The base bullion from the lead blast furnace contains varying amounts of the impurities left in the smelter feed by the concentrator, regardless of the method of smelter operation. These impurities may be held in part in mechanical suspension rather than being present as true alloys. However, usually there is little free space in the crucible in which to separate these drosses before the bullion is taken from the lead well. When such a dross is melted in a laboratory crucible and allowed to cool, the products obtained are lead bullion, speiss, and matte in well separated layers. Typical analyses of layers are: Analyses. Per Cent Element Bullion Speiss Matte Pb.............................................. 92.0 41.2 38.3 Cu.............................................. 2.4 36.3 40.6 As............................................... 4.0 16.5 4.3 Sb............................................... 0.7 0.2 0.4 S................................................ 0.6 1.9 13.1 Fe............................................... 0.0 0.0 0.0 Totals......................................... 99.7 96.1 96.7 The absence of iron in these products drossed from the blast-furnace bullion proves that the impurities for the greater part are not simply finely divided blast-furnace speiss or matte that has been dissolved or dispersed in the lead, but are held in solution by the liquid metal and rise to its surface as infusible compounds when the temperature of the bath is lowered. In general, the drosses made locally are metal sulphides and arsenides and not oxidized compounds. The large content of metallic lead also does not seem to be retained because of oxidized compounds

Jan 1, 1937

By P. F. McIntyre

Electrolytic refining of lead was first carried out on a commercial scale at Trail, B. C., in 1903. The capacity at that time was small, and cell-changing operations were managed with chain block and monorail. Development up to 1922, utilizing crane installations and cell additions, attained a production of 100 tons per day. Successive additions from 1922 to 1926 further increased the rated capacity to 396 tons per day. Other improvements in metallurgical practice have gradually increased production, until for the year 1935 it was 448 tons per day. During the first five months of 1936, an average daily production of 504 tons was maintained without increasing the size of the plant. Lead Refinery Buildings.—The tank room and the lead-melting and casting equipment are housed in two buildings, which parallel each other and which for the greater part of their lengths are joined by a connecting aisle. All basements, walls, sumps and floors are of concrete. Where exposed to the electrolyte, the concrete has a protective coating of asphalt (220" melting point) over a coat of asphalt paint as a primer. Buildings erected before 1924 are of wood. More recent additions are made of structural steel with gunite siding. A brick building, adjoining the older section of the tank room, houses the slimes-treatment plant. The power house, containing motor generators, air compressors and rectifiers, is constructed of tile. Cell Construction.—The electrolytic cells are of reinforced concrete lined with asphalt. They are cast in pairs, the outside dimensions of a double cell being 113 in. long by 73 in. wide by 48 in. deep. The bottom is 6 in. thick and the sides, ends and center wall are 4 in. thick. A ledge 3 in. wide and 2½ in. deep is left along the top of the side walls to carry the insulators and bus bars. Reinforcing consists of ½-in. round iron rods. Cell inspection and repair work is done in conjunction with the cell-changing operations. The repair work necessary is usually confined to renewing chipped asphalt, unless a tank has been accidentally broken. Minor concrete repairs can be easily made in place. The broken concrete

Jan 1, 1937

By H. J. Stehli

Probably the earliest sinter from lead ore was made in the product sinter boxes attached to some hand reverberatory roasters. The ore was drawn from the roaster bed when dead roasted, and then by laborious effort fritted together by rabbling at a high temperature in the sinter box. This was not a true sinter, but was a great improvement over the dusty dead-roasted fine ores. The Huntington-Heberlein pots were the first real advance in the art, and produced some real sinter. They required that the sulphides be preroasted to 5 or 6 per cent sulphur, and the long cycle of operating and deep bed of material used in the pots fostered the formation of densely fused material and fines. This necessitated crushing of the densely fused cake and returning to the next charge large amounts of fines screened out. The Huntington-Heberlein pots made comparatively high lead losses because the deep bed and high internal temperature together favored the volatilization of lead. Lime (CaO) was added to the charges, and this addition constituted the patented feature of the Huntington-Heberlein process. Its sole function we now know was to act as an isolator of the sulphide particles, and any other substance—for instance, iron oxide—of equal fineness performed the same function. The Savelsberg process used limestone instead of burned lime, and in this there was a definite advantage. The converting of CaCO3, to CaO is a highly endothermic reaction, so the lime acted not only as an isolator of sulphide particles but absorbed excess heat and to some extent prevented premature fusion of the sulphides. The Carmichael-Bradford process used gypsum instead of limestone, and had the disadvantage of adding more sulphur to a charge from which it was desired to eliminate sulphur. Here again the gypsum served only as an infusible isolator of sulphide particles. The first Dwight-Lloyd apparatus to sinter lead ores commercially was installed at Perth Amboy in 1907. The fact that lime in any form was necessary to sintering was quickly disproved by making excellent sinter from Bunker Hill and Sullivan table concentrates, silica sand and iron oxide only.

Jan 1, 1937

By J. B. Austin, H. H. Pierce

In developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measurements serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transformation temperature determined by any method in which the specimen is cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chromium or managanese. The lag, or undercooling, observed at the ? — a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys, which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dila-tometer previously described,' using a rate of heating and of cooling of 3.0" to 3.5" per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has been described.2 Results and Discussion Thermal Expansion Coeficients.—Numerical values for the linear expansion coefficient, derived from a smoothed curve based on at least

Jan 1, 1935

By H. H. Pierce, J. B. Austin

In developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measurements serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transformation temperature determined by any method in which the specimen is cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chromium or managanese. The lag, or undercooling, observed at the ? — a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys, which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dila-tometer previously described,' using a rate of heating and of cooling of 3.0" to 3.5" per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has been described.2 Results and Discussion Thermal Expansion Coeficients.—Numerical values for the linear expansion coefficient, derived from a smoothed curve based on at least

Jan 1, 1935

By H. B. Pulsifer

One of the most common basic open-hearth furnace products is a simple carbon steel with a carbon range from 0.05 to 0.15 per cent. The material is widely used for sheets, tubes, bars, wire and the innumerable special objects of secondary fabrication. The properties of the material vary over wide ranges, depending on the more exact composition and details of manufacture or treatment that affect its structure. The present paper is a review of those properties and structures that have been found by studying this steel as used in the cap screw industry. At first glance this might be thought a narrow application of the steel, but, since the industry uses the material in the cold-worked, annealed and heat-treated conditions, the title of the paper may be excused for its comprehensiveness. Yet, in studying the wide ranges of properties and structures that preclude a more specific title, there can be no suggestion of completeness or finality. Even a summary of a few years' work is no more than a preliminary survey of a field that will be fertile in scientific data and industrial products for many years to come. An outline of the structures will be given first, then a list of the previous contributions that are at hand and finally some details of the work and related problems, especially concerning this low-carbon steel in the surface-hardened condition. Wire Used in Manufacture of Cap Screws The wire that is used for making cold-upset and roll-threaded cap screws has been cold-drawn from hot-rolled rods that were pickled and limed. The common sizes used in the industry range from 0.185 to 0.750 in. dia., the exact diameters depending on the plant practice and having the usual tolerances of 0.002 in. for the smaller sizes and 0.003 in. for the larger sizes. The carbon range, by pit analysis, is usually between 0.07 and 0.12 per cent. Manganese should be within the usual 0.30 to 0.50 per cent. range. Sulfur rarely exceeds 0.045 per cent. and phosphorus seldom exceeds 0.030 per cent. Silicon is usually below 0.03 per cent. but in the silicon-killed steels may be in the customary 0.10 to 0.25 per cent. range. Rimmed steel is not considered most suitable for cap screws that are cold-headed or for parts that are to be surface-hardened.

Jan 1, 1931

By C. W. Davis, R. S. Dean

The purification of iron ores by means of hand magnets dates back more than 100 years. The first record in the United States Patent Office of a machine for the magnetic separation of ores shows that on Feb. 20, 1849, U.S. Patent 6121 was issued to Ransom Cook for improvement in electromagnetic ore separators. The patent covered the use of a revolving cylinder, or drum, with poles of electromagnets in its periphery for the purpose of separating magnetic oxide of iron from substances with which it might be associated, by causing the electrornagnets when revolving as component parts of the cylinder to be successively charged to take up the ore and discharged to part with it. Since this patent was issued the science and technique of magnetism have advanced more than most other fields of endeavor. The development of electrical machinery has required and obtained better and better magnetic materials, and the science of applied magnetism is as completely and satisfactorily developed as any branch of physics. Nevertheless, the patent of Ransom Cook, issued in 1849, comes close to covering everything that is now being applied in magnetic separation. The cynic may conclude that this proves the uselessness of modern science and may point in confirmation to flotation, which has grown in a few years, practically without benefit of science, to be the most versatile and useful of concentration methods. On more careful study, however, it appears that an accurate determination of the magnetic properties of minerals and their amenability to control by mechanical and heat treatments has not heretofore been made. The first essential, therefore, in the design of improved magnetic separators has been missing. In spite of this hiatus in scientific data inventors have been busy, and patents are on file covering mineral separations by means of nearly all known magneto-mechanical effects. Because of a lack of knowledge of mineral properties, most of these inventions never worked well enough to find commercial use. The Metallurgical Division

Jan 1, 1935

By Irwin Roman, Thomas C. Serman

It has been known for many years that when a wire is moved in a magnetic field, an electromotive force is developed which is proportional to the rate at which the wire is moved in a direction perpendicular to the magnetic intensity and to the magnetic intensity itself. If the ends of the wire are connected to a current indicator, the current behaves exactly as though the source of electromotive force were a galvanic cell. If a wire is wound circularly and rotated uniformly around a diameter not parallel to the intensity, the current flowing through the wire will be alternating of sinusoidal shape. If, instead of a single loop, there are several turns wound in a short helix, the electromotive force developed will be approximately proportional to the number of turns, the area of the helix and to the speed of rotation. The maximum electromotive force will be developed when the axis of rotation is perpendicular to the field; if this is not so, only the component of the intensity that is perpendicular to the axis of rotation is effective. This is the principle of the usual earth inductor. With a few turns of wire and comparatively slow rotation, it is possible to produce a considerable deflection of a galvanometer. If two similar coils are rotated together at two different points for which the magnetic field intensities perpendicular to the axes of rotation are different, the electromotive forces developed will each depend on its corresponding intensity and be a measure of that intensity. If the intensities are sufficiently different so that the electromotive forces may be compared, the two intensities may be compared. This is the principle

Jan 1, 1934

By A. S. Eve

In the spring of 1930, the question was raised as to the possibility of estimating the depth to which the pyrrhotite-nickel deposit at the Falconbridge mine extended in the earth. This body is 7500 ft. long, it dips at 80° to the north, and it is fairly straight with slight sinuosities. Dr. F. W. Lee suggested that it might be possible to solve the problem by measuring the vertical magnetic intensity, with a good magnetometer, both near the surface of the earth and also at a level a few feet higher in the air. The writer regarded this suggestion with some scepticism, but it was decided to put the scheme to a practical test. In July, 1930, Dr. Lee, Dr. Keys and the writer, with Mr. Joyce and Mr. Belloc as assistants, made a firm, light wooden platform (Fig. 1) measuring 4 by 4 ft. on the top, which was 10 ft. above ground. This platform could be moved easily a few yards by four men, and carried across country in a wagon or by motor truck. Some iron nails were used in its construction, but we were not able to detect their influence on the Askania magnetometer. Nevertheless, in future work, the use of iron should be completely avoided. Readings were taken along a traverse at right angles to the orebody, at several stations, both on the ground and on the platform. The excess readings, over the dike, as compared with those about 800 ft. away, are shown in Table 1. The largest reading, 6.8, is open to suspicion and should be rejected. The depth of the top of the orebody is known by electrical survey, and by actual drilling, to be about 112 to 123 ft., and the covering is sandy glacial drift. Similar readings were taken over a long straight magnetic diabase dike. These also are shown in Table 1. The magnetic vertical intensity is consistently less at the higher level, which is 10 ft. above the lower level.

Jan 1, 1932

By David A. Keys

The object of this investigation was to determine with a vertical magnetic variometer the extent of the titaniferous ore deposit that occurs not far from Ivry in Terrebonne County, Quebec, about 70 miles north of Montreal. The Ivry mine, on lots 37 and 38 of range V, Beres-ford township, Quebec, is one of the largest and most accessible to transportation of the deposits of ilmenite in Quebec. The ore consists of an aggregate of ilmenite anhedra serving as host for numerous fine plaques of hematite. No magnetite is known from any occurrence near this lot, and in this way the deposit differs from many others that contain a large percentage of magnetite with the ilmenite. The deposit at Ivry thus has much lower magnetic susceptibility than those containing abundant magnetite, and a sensitive magnetometer was necessary for the work, although a body of magnetite with ilmenite about a mile from the Ivry mine was successfully prospected with a dip needle. The principal orebody is exposed in a quarry known as the Ivry mine, from which about 16,000 tons of ore have been shipped. Small exposures of ilmenite isolated by drift serve to show the presence at the surface of some of the bodies indicated by the magnetometer, but most of the hill is covered with glacial till and second growth hardwood. At the lower levels the till gives place to fluvioglacial sands and gravels from which the forest has been cleared. The increasing thickness of the sand and gravel as the hill descends makes the tracing outward of the deposits from the rocky knob of anorthosite a difficult matter. Within the orebodies too, some masses of anorthosite persist, which may account for some local irregularities. Fig. 1 is a photomicrograph, taken by reflected light, of a typical specimen of the ore. The dark patches are hematite and the light parts are ilmenite No trace of magnetite was found. Pig. 2 is a photomicrograph of a thin section of the country rock showing the texture of the anorthosite. The mean of four analyses quoted by Robinson1 is: titaninm, 19.26 per cent; iron 45.41 per cent. The ilmenite ore is not sufficiently magnetic to deflect an ordinary compass needle, but the effects of the induced magnetism in the ore by

Jan 1, 1940

By David A. Keys

The object of this investigation was to determine with a vertical magnetic variometer the extent of the titaniferous ore deposit that occurs not far from Ivry in Terrebonne County, Quebec, about 70 miles north of Montreal. The Ivry mine, on lots 37 and 38 of range V, Beres-ford township, Quebec, is one of the largest and most accessible to transportation of the deposits of ilmenite in Quebec. The ore consists of an aggregate of ilmenite anhedra serving as host for numerous fine plaques of hematite. No magnetite is known from any occurrence near this lot, and in this way the deposit differs from many others that contain a large percentage of magnetite with the ilmenite. The deposit at Ivry thus has much lower magnetic susceptibility than those containing abundant magnetite, and a sensitive magnetometer was necessary for the work, although a body of magnetite with ilmenite about a mile from the Ivry mine was successfully prospected with a dip needle. The principal orebody is exposed in a quarry known as the Ivry mine, from which about 16,000 tons of ore have been shipped. Small exposures of ilmenite isolated by drift serve to show the presence at the surface of some of the bodies indicated by the magnetometer, but most of the hill is covered with glacial till and second growth hardwood. At the lower levels the till gives place to fluvioglacial sands and gravels from which the forest has been cleared. The increasing thickness of the sand and gravel as the hill descends makes the tracing outward of the deposits from the rocky knob of anorthosite a difficult matter. Within the orebodies too, some masses of anorthosite persist, which may account for some local irregularities. Fig. 1 is a photomicrograph, taken by reflected light, of a typical specimen of the ore. The dark patches are hematite and the light parts are ilmenite No trace of magnetite was found. Pig. 2 is a photomicrograph of a thin section of the country rock showing the texture of the anorthosite. The mean of four analyses quoted by Robinson1 is: titaninm, 19.26 per cent; iron 45.41 per cent. The ilmenite ore is not sufficiently magnetic to deflect an ordinary compass needle, but the effects of the induced magnetism in the ore by

Jan 1, 1940