Search Documents

By Sylvain J. Pirson

The main value of earth magnetic measurements, outside of certain mining problems, resides in the study of deeply buried tectonic phenomena related to regional and local geology. Magnetic surveys are a necessary complement of gravimetric measurements, especially of pendulum surveys. To date, magnetometer prospecting has been used chiefly in the study of sedimentary basins where petroleum structures are associated with the uplifted basement rocks. There are, in the literature, innumerable articles dealing with such surveys as applied to oil geology but few treat of broad geological features related to regional magnetic disturbances of the earth field. An important piece of coordination work has been made by Jean Jungl for the magnetic and gravimetric measurements made in France and their geologic significance. A similar attempt at correlation of the known geology with the anomalies of the vertical component of the earth magnetic field has been made for the United States by George B. Somers2. Taking the magnetic vector as a whole, W. P. Jenny3 made a coordination of magnetism and geology for the main producing oil states of the United States. A more detailed study along the same lines is published by A. Van Weelden4 for southern Oklahoma and northern Texas; in this work magnetic and gravimetric measurements taken at stations as close as one mile apart are compiled and compared to the regional geology of the Ouachita-Amarillo uplifted area. From the literature mentioned, it is evident that reliable interpretation of magnetic' anomalies can be arrived at only when the magnetic stations are numerous and cover the area in a close net of measurements, therefore the works of Somers and Jenny, based on sparsely distributed Government measurements, can be regarded only as preliminary programs indicating lines along which further work should be done, whereas the coordination made by Van Weelden is an example of the contribution to the knowledge of regional geology that can be arrived at by the use of applied geophysics. With the hope that further systematic magnetic measurements will be carried on to solve regional and local geological problems, the author

Jan 1, 1940

By Sylvain J. Pirson

The main value of earth magnetic measurements, outside of certain mining problems, resides in the study of deeply buried tectonic phenomena related to regional and local geology. Magnetic surveys are a necessary complement of gravimetric measurements, especially of pendulum surveys. To date, magnetometer prospecting has been used chiefly in the study of sedimentary basins where petroleum structures are associated with the uplifted basement rocks. There are, in the literature, innumerable articles dealing with such surveys as applied to oil geology but few treat of broad geological features related to regional magnetic disturbances of the earth field. An important piece of coordination work has been made by Jean Jungl for the magnetic and gravimetric measurements made in France and their geologic significance. A similar attempt at correlation of the known geology with the anomalies of the vertical component of the earth magnetic field has been made for the United States by George B. Somers2. Taking the magnetic vector as a whole, W. P. Jenny3 made a coordination of magnetism and geology for the main producing oil states of the United States. A more detailed study along the same lines is published by A. Van Weelden4 for southern Oklahoma and northern Texas; in this work magnetic and gravimetric measurements taken at stations as close as one mile apart are compiled and compared to the regional geology of the Ouachita-Amarillo uplifted area. From the literature mentioned, it is evident that reliable interpretation of magnetic' anomalies can be arrived at only when the magnetic stations are numerous and cover the area in a close net of measurements, therefore the works of Somers and Jenny, based on sparsely distributed Government measurements, can be regarded only as preliminary programs indicating lines along which further work should be done, whereas the coordination made by Van Weelden is an example of the contribution to the knowledge of regional geology that can be arrived at by the use of applied geophysics. With the hope that further systematic magnetic measurements will be carried on to solve regional and local geological problems, the author

Jan 1, 1940

By Cyril Stanley Smith

On the 6th of February 1684, Dr. Martin Lister mentioned at a meeting of the Royal Society1 that "brass is magnetical," and promised to give an account of that assertion at some other time. He repeated his promise but never fulfilled it, and it was left for William Arderon2 to show, in 1758, that brass could be made magnetic by hammering and that it would retain polarity after magnetizing. Twenty-seven years later Caval103,4 examined the matter in great detail. Working with cast calamine brass, he showed that it could be made magnetic by hammering and nonmagnetic by subsequent annealing at a red heat. He found that annealing at a very high temperature caused the samples to lose their magnetic quality permanently, even after subsequent cold-working, but that remelting and cold- working restored it. He encountered some samples of brass that could not be rendered - magnetic by any treatment. Experiments in which these were remelted with iron additions gave negative results, and Cavallo concluded that iron impurity was not the cause of the magnetism. He worked with 50-grain (3-gram) samples melted under the blowpipe, hence cooled very quickly. Bennet5 made whole crucible charges from copper and zinc, and found _ the resulting brass ingots to be magnetic only when iron had been added and then only after cold-working. All these observations applied to material in the cast condi- tion, in which coring would produce a continuous spectrum of composition and cooling would result in varying degrees of precipitation. This knowledge of the subject seems to have been forgotten in the nineteenth century. The older brass was made by the calamine process and frequently contained iron in amounts of 0.5 per cent or more, absorbed from the impure ore with which the copper and charcoal were heated in making the brass. When metallic zinc became available in commercial quantities, calamine brass gradually disappeared, and with it the knowledge of its curious magnetic properties. Only when sensitive apparatus replaced the compass needle of the earlier investigators could the effects be detected in relatively pure metal. The effect of cold-working in inducing ferromagnetism was rediscovered by Bitter8 in 1930 in a sample of impure copper, and this was confirmed by Lowance and Constant: Honda and Shimizu, l0,11 and others. In the same year, Tammann and Oelsen12 showed that copper-rich copper-iron alloys after certain heat-treatments could be rendered ferromagnetic or made more strongly ferromagnetic by cold-rolling. Kussman and Seeman13 showed that the change of susceptibility of relatively pure copper on cold-working was associated with the iron content, and concluded that actual precipitation of iron was caused by cold-working, which is a satisfactory theory until one considers the improbably high rate of diffusion that this would involve. When studying precipitation phenomena in

Jan 1, 1942

By Cyril Stanley Smith

On the 6th of February 1684, Dr. Martin Lister mentioned at a meeting of the Royal Society1 that "brass is magnetical," and promised to give an account of that assertion at some other time. He repeated his promise but never fulfilled it, and it was left for William Arderon2 to show, in 1758, that brass could be made magnetic by hammering and that it would retain polarity after magnetizing. Twenty-seven years later Caval103,4 examined the matter in great detail. Working with cast calamine brass, he showed that it could be made magnetic by hammering and nonmagnetic by subsequent annealing at a red heat. He found that annealing at a very high temperature caused the samples to lose their magnetic quality permanently, even after subsequent cold-working, but that remelting and cold- working restored it. He encountered some samples of brass that could not be rendered - magnetic by any treatment. Experiments in which these were remelted with iron additions gave negative results, and Cavallo concluded that iron impurity was not the cause of the magnetism. He worked with 50-grain (3-gram) samples melted under the blowpipe, hence cooled very quickly. Bennet5 made whole crucible charges from copper and zinc, and found _ the resulting brass ingots to be magnetic only when iron had been added and then only after cold-working. All these observations applied to material in the cast condi- tion, in which coring would produce a continuous spectrum of composition and cooling would result in varying degrees of precipitation. This knowledge of the subject seems to have been forgotten in the nineteenth century. The older brass was made by the calamine process and frequently contained iron in amounts of 0.5 per cent or more, absorbed from the impure ore with which the copper and charcoal were heated in making the brass. When metallic zinc became available in commercial quantities, calamine brass gradually disappeared, and with it the knowledge of its curious magnetic properties. Only when sensitive apparatus replaced the compass needle of the earlier investigators could the effects be detected in relatively pure metal. The effect of cold-working in inducing ferromagnetism was rediscovered by Bitter8 in 1930 in a sample of impure copper, and this was confirmed by Lowance and Constant: Honda and Shimizu, l0,11 and others. In the same year, Tammann and Oelsen12 showed that copper-rich copper-iron alloys after certain heat-treatments could be rendered ferromagnetic or made more strongly ferromagnetic by cold-rolling. Kussman and Seeman13 showed that the change of susceptibility of relatively pure copper on cold-working was associated with the iron content, and concluded that actual precipitation of iron was caused by cold-working, which is a satisfactory theory until one considers the improbably high rate of diffusion that this would involve. When studying precipitation phenomena in

Jan 1, 1942

By R. S. Dean

The careful work of Gross and Zimmerleyl has established the fact that the energy actually used in grinding is proportional to the new surface produced. This confirmation of Rittinger's law was made by crushing quartz in a frictionless drop-weight machine and determining the surface of the quartz by its rate of solution in hydrofluoric acid. The details of this procedure have been described adequately elsewhere and need not be repeated here. The resultant data furnish the only available basis for comparing accurately the efficiency of grinding machines. This method is so cumbersome experimentally that it has been little used. As an alternative all sorts of approximations have been proposed. The best of these is complete size analysis by sieving and elutria-tion. Such procedure is very lengthy and difficult to carry out accurately. Furthermore, any sizing method becomes very inaccurate for determining surface with very fine sizes where the ratio of surface to volume becomes very large. To avoid the lengthy and difficult technique of elutriation it has been proposed to estimate the size distribution below 200 mesh from various probability formulas. Such a procedure is at best an engineering approximation; at worst it is a mere guess. Some time ago Dr. V. H. Gottschalk2 found that the coercive forces of magnetite powders were directly proportional to the surface area, regardless of size distribution. It was at once apparent that this furnished a method for determining grinding efficiency quickly and accurately. The only requirement was a single determination of the relation between the work input of the Gross-Zimmerley drop-weight machine and the coercive force of the resultant crushed magnetite. For this purpose Ural Mountain magnetite in definite octahedra was

Jan 1, 1939

By R. S. Dean

The careful work of Gross and Zimmerleyl has established the fact that the energy actually used in grinding is proportional to the new surface produced. This confirmation of Rittinger's law was made by crushing quartz in a frictionless drop-weight machine and determining the surface of the quartz by its rate of solution in hydrofluoric acid. The details of this procedure have been described adequately elsewhere and need not be repeated here. The resultant data furnish the only available basis for comparing accurately the efficiency of grinding machines. This method is so cumbersome experimentally that it has been little used. As an alternative all sorts of approximations have been proposed. The best of these is complete size analysis by sieving and elutria-tion. Such procedure is very lengthy and difficult to carry out accurately. Furthermore, any sizing method becomes very inaccurate for determining surface with very fine sizes where the ratio of surface to volume becomes very large. To avoid the lengthy and difficult technique of elutriation it has been proposed to estimate the size distribution below 200 mesh from various probability formulas. Such a procedure is at best an engineering approximation; at worst it is a mere guess. Some time ago Dr. V. H. Gottschalk2 found that the coercive forces of magnetite powders were directly proportional to the surface area, regardless of size distribution. It was at once apparent that this furnished a method for determining grinding efficiency quickly and accurately. The only requirement was a single determination of the relation between the work input of the Gross-Zimmerley drop-weight machine and the coercive force of the resultant crushed magnetite. For this purpose Ural Mountain magnetite in definite octahedra was

Jan 1, 1939

By C. D. Ramsden

During the war years of 1941 to 1945, maintenance of mine locomotives and other mine equipment took the form of rebuilding rather than of renewing. Purchase of new parts became increasingly difficult and mine operators found it necessary to maintain equipment by salvaging old parts. Mine-locomotive wheels, although not representing a high cost per pound of material, contain a considerable amount of steel and without rebuilding would have to be scrapped long before even a moderate percentage of the steel in the wheel is actually consumed. Many mine operators have been rebuilding locomotive wheels for several years with automatic open are-welding equipment. In 1927, the Pittsburgh Coal Co. started such a program, using a single Westinghouse automatic welding head. Since that time, many refinements have been added, until in 1944 the setup was operating very efficiently. A desire to increase wheel life and to hold down rising costs led the company in 1944 to investigate the possibilities of the under-flux are-welding process for wheel rebuilding, although at that time, little or no work had been done on multiple pass or "build-up" welding with the underflux arc. Work with this process had been confined largely to welding together flat plates in a "down hand" position. Possibilities for savings were intensified by the fact that the company has 300 locomotives in operation, using actively or as spares 1200 sets of wheels. During 1942 and 1943, about 500 sets of wheels were sent each year to the company's maintenance shop at Library, Pa., for rebuilding. Based on having 800 sets in service (many of the company's heavy locomotives have three sets of trucks), the average life of a set of wheels was approximately 19 months. Anything that could be done to increase wheel life promised sizable annual savings. Open Arc Welding With the open arc process, a set of wheels could be rebuilt for about 40 pet of the cost' of new wheels. Underflux arc welding gave promise of greatly increased welding speeds, more homogeneous, dense deposits and the chance for use of a wider range in welding-wire compositions. Against this was ranged the higher cost of materials and the cost of developing the process from the theory to a practical reality. Since 1927, when a single open arc head was placed in operation, fixed welding procedures had been gradually developed, a positioner for handling a set of wheels was built, and a second head was placed in operation in order to weld two wheels simultaneously. The fixture, or positioner, which was built to position and turn the wheels under the two welding heads, included a motor drive, controlled by a rheostat, which rotated the wheels through a double set of speed reducers and a removable jaw coupling attached to one end of the axle of the wheel truck.

Jan 1, 1947

By C. D. Ramsden

During the war years of 1941 to 1945, maintenance of mine locomotives and other mine equipment took the form of rebuilding rather than of renewing. Purchase of new parts became increasingly difficult and mine operators found it necessary to maintain equipment by salvaging old parts. Mine-locomotive wheels, although not representing a high cost per pound of material, contain a considerable amount of steel and without rebuilding would have to be scrapped long before even a moderate percentage of the steel in the wheel is actually consumed. Many mine operators have been rebuilding locomotive wheels for several years with automatic open are-welding equipment. In 1927, the Pittsburgh Coal Co. started such a program, using a single Westinghouse automatic welding head. Since that time, many refinements have been added, until in 1944 the setup was operating very efficiently. A desire to increase wheel life and to hold down rising costs led the company in 1944 to investigate the possibilities of the under-flux are-welding process for wheel rebuilding, although at that time, little or no work had been done on multiple pass or "build-up" welding with the underflux arc. Work with this process had been confined largely to welding together flat plates in a "down hand" position. Possibilities for savings were intensified by the fact that the company has 300 locomotives in operation, using actively or as spares 1200 sets of wheels. During 1942 and 1943, about 500 sets of wheels were sent each year to the company's maintenance shop at Library, Pa., for rebuilding. Based on having 800 sets in service (many of the company's heavy locomotives have three sets of trucks), the average life of a set of wheels was approximately 19 months. Anything that could be done to increase wheel life promised sizable annual savings. Open Arc Welding With the open arc process, a set of wheels could be rebuilt for about 40 pet of the cost' of new wheels. Underflux arc welding gave promise of greatly increased welding speeds, more homogeneous, dense deposits and the chance for use of a wider range in welding-wire compositions. Against this was ranged the higher cost of materials and the cost of developing the process from the theory to a practical reality. Since 1927, when a single open arc head was placed in operation, fixed welding procedures had been gradually developed, a positioner for handling a set of wheels was built, and a second head was placed in operation in order to weld two wheels simultaneously. The fixture, or positioner, which was built to position and turn the wheels under the two welding heads, included a motor drive, controlled by a rheostat, which rotated the wheels through a double set of speed reducers and a removable jaw coupling attached to one end of the axle of the wheel truck.

Jan 1, 1947

By John S. Johnson

The maintenance cost, or renewal cost, in any preparation plant is a large item of expense and reflects in the total cost of producing and preparing the ton of coal. It is given constant study to the end that ways and means of controlling and reducing this proportion of the total cost may be developed. Study of this item of cost has proceeded along usual lines, which are: proper functioning of the maintenance organization; systematic and thorough inspection to prevent breakdonns; the making of repairs before renewals are needed; maintenance work done thoroughly the first time, instead of patching, study of parts needing frequent renewal or repairs or conditions resulting in delays, thorough knowledge of cost by the mall responsible for maintenance; and the use of special equipment and materials. This paper is to deal with special equipment and materials to reduce the maintenance cost hut before going into that I want to express an opinion on the general subject. Maintenance Organization Usually maintenance is taken care of by a group of men who perform their work on the off shift. The work is arranged by the operating official who should be thoroughly familiar with maintenance, so that materials needed may be made up for the particular job and waste of time in looking up materials be prevented. To perfect the maintenance organization, all operating attendants should be thoroughly trained to be familiar with all working parts of their equipment, to make a thorough inspection and to write out the slip for the work required. This requires job analysis, but it is worth the effort, because the attendant usually is better informed than anyone else about his particular equipment. The operating official can judge the scope of the work to direct the repair and to have material ready. Lubrication is an important item in maintenance, and a subject by itself. Usually the breaker oiler is designated to perform this task. This man should be picked for his ability and put in line for promotion to machinist. He should be trained as an inspector, as he is constantly visiting most parts of the breaker and has an opportunity to observe needed maintenance. The first thing is to lay out maintenance work and arrange to have it done; the next is to check the work and see that it has been properly done. This check should be made by the operating official, and through the attendant. The cost statement showing the various items of maintenance cost is not often understood by the man in direct charge. Cost sheets should be simplified and worked up by breaker sections; e.g., the cost of

Jan 1, 1947

By John S. Johnson

The maintenance cost, or renewal cost, in any preparation plant is a large item of expense and reflects in the total cost of producing and preparing the ton of coal. It is given constant study to the end that ways and means of controlling and reducing this proportion of the total cost may be developed. Study of this item of cost has proceeded along usual lines, which are: proper functioning of the maintenance organization; systematic and thorough inspection to prevent breakdonns; the making of repairs before renewals are needed; maintenance work done thoroughly the first time, instead of patching, study of parts needing frequent renewal or repairs or conditions resulting in delays, thorough knowledge of cost by the mall responsible for maintenance; and the use of special equipment and materials. This paper is to deal with special equipment and materials to reduce the maintenance cost hut before going into that I want to express an opinion on the general subject. Maintenance Organization Usually maintenance is taken care of by a group of men who perform their work on the off shift. The work is arranged by the operating official who should be thoroughly familiar with maintenance, so that materials needed may be made up for the particular job and waste of time in looking up materials be prevented. To perfect the maintenance organization, all operating attendants should be thoroughly trained to be familiar with all working parts of their equipment, to make a thorough inspection and to write out the slip for the work required. This requires job analysis, but it is worth the effort, because the attendant usually is better informed than anyone else about his particular equipment. The operating official can judge the scope of the work to direct the repair and to have material ready. Lubrication is an important item in maintenance, and a subject by itself. Usually the breaker oiler is designated to perform this task. This man should be picked for his ability and put in line for promotion to machinist. He should be trained as an inspector, as he is constantly visiting most parts of the breaker and has an opportunity to observe needed maintenance. The first thing is to lay out maintenance work and arrange to have it done; the next is to check the work and see that it has been properly done. This check should be made by the operating official, and through the attendant. The cost statement showing the various items of maintenance cost is not often understood by the man in direct charge. Cost sheets should be simplified and worked up by breaker sections; e.g., the cost of

Jan 1, 1947

By C. C. Henning

In any line of human activity logical handling requires an amount of attention to each phase that is in keeping with the importance of that phase. In the complex and rapidly changing field of modern ferrous metallurgy it is difficult to allot the proper degree of attention to the various subjects, and it is not surprising that one or more subjects of major importance should for a time be neglected. Bessemer steel is a good example of a neglected subject. It is largely taken for granted, inferior physical quality is assumed for it, and there is a • lack of interest in its technical development and commercial application. Availability of supply is limited. In spite of this technical indifference, limited source and lack of commercial exploitation, bessemer steel constitutes a large volume of tonnage in daily use. There is a fairly prevalent idea even among technical people that bessemer steel survives mostly because of low cost and by reason of a dwindling residue of applications sufficiently common to permit of its use. The difference in cost between bessemer and open-hearth steel is governed largely by the relative cost of manufacture of pig iron and the market price of steel scrap. During the past four years there have been long periods of time during which the price of steel scrap was low enough so that open-hearth steel was considerably lower in manufacturing cost than bessemer. As to application, it may be pointed out that thousands of tons of this material in the form of bessemer screw steel are applied for moving parts in automotive and other equipment. Some forging work and considerable heat-treating, particularly carburizing, is performed on this grade. From an economic standpoint the most effective contribution of bessemer steel lies in its free machining qualities. It is by far the freest

Jan 1, 1935

By C. C. Henning

In any line of human activity logical handling requires an amount of attention to each phase that is in keeping with the importance of that phase. In the complex and rapidly changing field of modern ferrous metallurgy it is difficult to allot the proper degree of attention to the various subjects, and it is not surprising that one or more subjects of major importance should for a time be neglected. Bessemer steel is a good example of a neglected subject. It is largely taken for granted, inferior physical quality is assumed for it, and there is a • lack of interest in its technical development and commercial application. Availability of supply is limited. In spite of this technical indifference, limited source and lack of commercial exploitation, bessemer steel constitutes a large volume of tonnage in daily use. There is a fairly prevalent idea even among technical people that bessemer steel survives mostly because of low cost and by reason of a dwindling residue of applications sufficiently common to permit of its use. The difference in cost between bessemer and open-hearth steel is governed largely by the relative cost of manufacture of pig iron and the market price of steel scrap. During the past four years there have been long periods of time during which the price of steel scrap was low enough so that open-hearth steel was considerably lower in manufacturing cost than bessemer. As to application, it may be pointed out that thousands of tons of this material in the form of bessemer screw steel are applied for moving parts in automotive and other equipment. Some forging work and considerable heat-treating, particularly carburizing, is performed on this grade. From an economic standpoint the most effective contribution of bessemer steel lies in its free machining qualities. It is by far the freest

Jan 1, 1935

By A. E. Harnsberger

I is obvious that details such as the physical and chemical properties and methods of heat-treating of the materials mentioned must be omitted in a paper on the subject of materials used in oil-refinery pumps1. Only sufficient identification is given to enable the reader to find additional information from already published data. Also, the subject covers many operating conditions, but only the most important services can be discussed here. To the oil refiner, the pumping equipment is of vital interest. Practically every refinery operation, from the charging of crude oil to a distillation unit to the shipping of refined products, involves some form of pumping machinery. Intermediate refining stages involve a great variety of pumping machinery to carry out successfully the aims of the refinery technologist. Temperatures at which oils are handled vary from — 50" F. to 900" F. Pressure may vary from subatmospheric to 2000 1b. per sq. inch. The selection of the proper materials involves a careful consideration of the conditions under which the particular pump must operate. The four most important considerations are temperature, pressure, corrosion, and abrasion or wear. Consideration of temperature may be divided into three parts: (1) extremely low temperatures of the order of —50" F.; (2) temperatures at atmospheric or slightly above; (3) temperatures from 200" to 900" F. Pressures fall into two groups: (1) pressures reached by ordinary trade pumps of the order of 200 lb. per sq. in., (2) extreme pressure conditions involving pressures as high as 2000 lb. Noncorrosive and corrosive oils can be treated differently. Under the latter falls corrosion in the presence of water, which will occur up to 250" F. The second type of corrosion occurs in high-temperature pumping equipment, with temperatures from 450" to 900" F., largely caused by sulfur compounds. There are also other corrosive conditions met with in refinery operations, particularly in the handling of acids, acid sludges and other specialized processes. These problems, although difficult to

Jan 1, 1935

By A. E. Harnsberger

I is obvious that details such as the physical and chemical properties and methods of heat-treating of the materials mentioned must be omitted in a paper on the subject of materials used in oil-refinery pumps1. Only sufficient identification is given to enable the reader to find additional information from already published data. Also, the subject covers many operating conditions, but only the most important services can be discussed here. To the oil refiner, the pumping equipment is of vital interest. Practically every refinery operation, from the charging of crude oil to a distillation unit to the shipping of refined products, involves some form of pumping machinery. Intermediate refining stages involve a great variety of pumping machinery to carry out successfully the aims of the refinery technologist. Temperatures at which oils are handled vary from — 50" F. to 900" F. Pressure may vary from subatmospheric to 2000 1b. per sq. inch. The selection of the proper materials involves a careful consideration of the conditions under which the particular pump must operate. The four most important considerations are temperature, pressure, corrosion, and abrasion or wear. Consideration of temperature may be divided into three parts: (1) extremely low temperatures of the order of —50" F.; (2) temperatures at atmospheric or slightly above; (3) temperatures from 200" to 900" F. Pressures fall into two groups: (1) pressures reached by ordinary trade pumps of the order of 200 lb. per sq. in., (2) extreme pressure conditions involving pressures as high as 2000 lb. Noncorrosive and corrosive oils can be treated differently. Under the latter falls corrosion in the presence of water, which will occur up to 250" F. The second type of corrosion occurs in high-temperature pumping equipment, with temperatures from 450" to 900" F., largely caused by sulfur compounds. There are also other corrosive conditions met with in refinery operations, particularly in the handling of acids, acid sludges and other specialized processes. These problems, although difficult to

Jan 1, 1935

By J. R. Low, M. Gensamer

During the course of an investigation into the drawability of automobile-body sheet steel, it became apparent that certain advantages would be possessed by a deep-drawing steel with a very low yield strength, but almost normal tensile strength, provided a reduction in yield strength could be accomplished without sacrifice of ductility and fine grain size. It would also be desirable to have this steel free from strain-aging; that is, free from the tendency for the yield point to return after it had been eliminated by straining. It was known that, wet hydrogen treatment acted to eliminate aging, but as carried out by other investigators, at relatively high temperatures, this treatment resulted in grain coarsening. It has been established by some of the experiments reported in this paper that all of these objectives can be accomplished by treatment in wet hydrogen at a low temperature, in the neighborhood of 72o°C. The time of treatment is relatively short (about 3 hr, to completion with 20-gauge sheet) if the water content of the hydrogen atmosphere is made fairly high, say aimost 30 per cent by volume. At this temperature. the grain size remains fine in the time required. After this treatment sheet reduced the usual amount by cold-rolling has a grain size of about A.S.T.M. No. 7. The yield point is completely eliminated, and the yield strength is reduced to a very low value, in the neighborhood of 15,000 lb. per sq. in. The stress-strain curve departs gradually from the straight-line elastic part after the fashion of nonferrous deep-drawing alloys. This elimination of the yield point is accompanied by a verv low indentation hardness; for example, 32 Rockwell B or even lower. There is no aging as measured by increase in the yield strength upon aging at room temperature or for 3 hr. at 200°C., after stretching about 10 per cent in tension. Tensile strength is only slightly less than the box-annealed sheet, seldom dropping much below 40,-ooo lb. per sq. in. Elongation is practically unchanged, or increased slightly. The term yield point, as here used, refers to the phenomenon of heterogeneous deformation occurring at a substantiallv constant load, observed principally in annealed low-carbon steels. If such a steel is loaded in tension, the load increases steadily with elastic strain, suddenly falls, fluctuates slightly about some constant value for a time and then begins to rise again as deformation proceeds. The maximum initial load before the sudden drop is generally called the "upper yield point"; the value of the load where deformation proceeds at a

Jan 1, 1944

By J. R. Low, M. Gensamer

During the course of an investigation into the drawability of automobile-body sheet steel, it became apparent that certain advantages would be possessed by a deep-drawing steel with a very low yield strength, but almost normal tensile strength, provided a reduction in yield strength could be accomplished without sacrifice of ductility and fine grain size. It would also be desirable to have this steel free from strain-aging; that is, free from the tendency for the yield point to return after it had been eliminated by straining. It was known that, wet hydrogen treatment acted to eliminate aging, but as carried out by other investigators, at relatively high temperatures, this treatment resulted in grain coarsening. It has been established by some of the experiments reported in this paper that all of these objectives can be accomplished by treatment in wet hydrogen at a low temperature, in the neighborhood of 72o°C. The time of treatment is relatively short (about 3 hr, to completion with 20-gauge sheet) if the water content of the hydrogen atmosphere is made fairly high, say aimost 30 per cent by volume. At this temperature. the grain size remains fine in the time required. After this treatment sheet reduced the usual amount by cold-rolling has a grain size of about A.S.T.M. No. 7. The yield point is completely eliminated, and the yield strength is reduced to a very low value, in the neighborhood of 15,000 lb. per sq. in. The stress-strain curve departs gradually from the straight-line elastic part after the fashion of nonferrous deep-drawing alloys. This elimination of the yield point is accompanied by a verv low indentation hardness; for example, 32 Rockwell B or even lower. There is no aging as measured by increase in the yield strength upon aging at room temperature or for 3 hr. at 200°C., after stretching about 10 per cent in tension. Tensile strength is only slightly less than the box-annealed sheet, seldom dropping much below 40,-ooo lb. per sq. in. Elongation is practically unchanged, or increased slightly. The term yield point, as here used, refers to the phenomenon of heterogeneous deformation occurring at a substantiallv constant load, observed principally in annealed low-carbon steels. If such a steel is loaded in tension, the load increases steadily with elastic strain, suddenly falls, fluctuates slightly about some constant value for a time and then begins to rise again as deformation proceeds. The maximum initial load before the sudden drop is generally called the "upper yield point"; the value of the load where deformation proceeds at a

Jan 1, 1944

By John H. Hollomon, C. Zener

It is commonly recognized that a given material may be described as ductile or brittle only with reference to the conditions of test. Thus under the usual test conditions quartz is brittle, but under high pressures it is ductile. Salts that are brittle at room temperature become ductile at elevated temperatures. Pitch, brittle with respect to rapid loads, flows at low rates of loading. Pearlitic steel, ductile under the usual conditions of test, may be embrittled under the proper conditions of combined stresses, temperature, and rate of loading. Earlier Investigations A clear analysis of the conditions necessary for plastic flow and for fracture was first given by LudwikI1 who introduced two types of stress, the "flow stress" and the "stress at fracture." These stresses may refer to tensile or to shear stresses, or, in fact, to any type of stress. Ludwik considered these two stresses to be independent of one another, functions of the conditions of test and of the prior history of the material. For the purpose of analysis. both a Flow stress and a stress at fracture can be envisaged as functions of strain over the entire range from zero to infinite strain. Thus, the material is brittle if the stress at fracturc is less than the flow stress and ductile if the reverse is true. According to Ludwik's analysis, the problem of determining the effects of combined stresses, of temperature and of strain rate upon the behavior of metals reduces to a problem of determining the effect of these variables upon the flow stress and upon the stress at fracture. In the present paper, methods are described for determining the effects of two of these variables, temperature and strain rate, and examples are given of the dependence of tlow stress and stress at fracture, upon these two variables. The effect of combined stresses will be discussed in a succeeding paper. The flow stress may be determined from a load-diameter curve. Load-diameter curves were obtained over a wide range of temperature and over the limited range of strain rates obtainable with the lever-type Riehle machine used. The curves were then converted to an extremely wide range of strain rate by making use of the equivalence of the effects of changes in strain rate and changes in temperature, previously proposed2 and demonstrated3 by the authors. According to this principle of equivalence, strain rate e and temperature T affect the flow stress only through a single parameter-p of the form: p = eeQ/RT 111 In this equation, R is the gas constant (2 cal. per gram mol per deg. C.), and Q is a heat of activation, which varies from material to material, and may depend upon the strain, but not upon the strain rate or the temperature. There is associated with every value of p a flow-stress curve. article of strain rate and of temperature that give the same p have the same flow-stress curve. Therefore, merely by changing the temperature of test, the effect of changing the strain rate may be obtained. Thus, under isothermal conditions, the material will behave the same at

Jan 1, 1944

By C. Zener, John H. Hollomon

It is commonly recognized that a given material may be described as ductile or brittle only with reference to the conditions of test. Thus under the usual test conditions quartz is brittle, but under high pressures it is ductile. Salts that are brittle at room temperature become ductile at elevated temperatures. Pitch, brittle with respect to rapid loads, flows at low rates of loading. Pearlitic steel, ductile under the usual conditions of test, may be embrittled under the proper conditions of combined stresses, temperature, and rate of loading. Earlier Investigations A clear analysis of the conditions necessary for plastic flow and for fracture was first given by LudwikI1 who introduced two types of stress, the "flow stress" and the "stress at fracture." These stresses may refer to tensile or to shear stresses, or, in fact, to any type of stress. Ludwik considered these two stresses to be independent of one another, functions of the conditions of test and of the prior history of the material. For the purpose of analysis. both a Flow stress and a stress at fracture can be envisaged as functions of strain over the entire range from zero to infinite strain. Thus, the material is brittle if the stress at fracturc is less than the flow stress and ductile if the reverse is true. According to Ludwik's analysis, the problem of determining the effects of combined stresses, of temperature and of strain rate upon the behavior of metals reduces to a problem of determining the effect of these variables upon the flow stress and upon the stress at fracture. In the present paper, methods are described for determining the effects of two of these variables, temperature and strain rate, and examples are given of the dependence of tlow stress and stress at fracture, upon these two variables. The effect of combined stresses will be discussed in a succeeding paper. The flow stress may be determined from a load-diameter curve. Load-diameter curves were obtained over a wide range of temperature and over the limited range of strain rates obtainable with the lever-type Riehle machine used. The curves were then converted to an extremely wide range of strain rate by making use of the equivalence of the effects of changes in strain rate and changes in temperature, previously proposed2 and demonstrated3 by the authors. According to this principle of equivalence, strain rate e and temperature T affect the flow stress only through a single parameter-p of the form: p = eeQ/RT 111 In this equation, R is the gas constant (2 cal. per gram mol per deg. C.), and Q is a heat of activation, which varies from material to material, and may depend upon the strain, but not upon the strain rate or the temperature. There is associated with every value of p a flow-stress curve. article of strain rate and of temperature that give the same p have the same flow-stress curve. Therefore, merely by changing the temperature of test, the effect of changing the strain rate may be obtained. Thus, under isothermal conditions, the material will behave the same at

Jan 1, 1944

By Nicholas Kowall, K. L. Clark

Maximum furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. Work oF Other Investigators In I938, Burns, Moore and Archer published & curve? that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the rallge found in construc-tional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only o.2o per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E 43xx steels, His procedure consisted of chill-casting a test bar that was large enough to give a a that could be prepared for Brinell indentations. The test piece was quenched immediately after solidi fication was complete and hardness readings were taken, so that the carbon content could he read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. Experimental Work Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944

By K. L. Clark, Nicholas Kowall

Maximum furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. Work oF Other Investigators In I938, Burns, Moore and Archer published & curve? that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the rallge found in construc-tional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only o.2o per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E 43xx steels, His procedure consisted of chill-casting a test bar that was large enough to give a a that could be prepared for Brinell indentations. The test piece was quenched immediately after solidi fication was complete and hardness readings were taken, so that the carbon content could he read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. Experimental Work Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944