Search Documents

By James Terry Duce

The symposium on production for the year 1940 contains few papers on the foreign situation. It is probable that the foreign part of next year's symposium will be even shorter. This is due to rigid censorship in various countries, as the question of the volume of petroleum supplies has become one of great strategic importance. This is even more true than in the last war, owing to greater mechanization of armies. 'It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts from Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not de-terminable frod data available to the author, please inserty; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In sucli cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved') and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when

Jan 1, 1941

By Max Y. Seaton

The scope of this paper will be limited to finished materials that contain a large preponderance (around 80 per cent or more) of magnesium oxide. The large and commercially important production of refractory dolomite and modified dolomites is not discussed here, and the production of magnesium basic carbonate for use as a heat insulator is barely mentioned. The discussion is confined mainly to magnesias produced in comparatively great quantity by direct processing of naturally occurring raw materials and hence excludes secondary or highly purified products such as pharmaceutical products or U.S.P. light and heavy calcined magnesias of commerce. Nomenclature The nomenclature of the magnesia products that will be discussed is somewhat confusing, in that it is customary in the trade to designate as "calcined magnesite" the materials that result from the calcining of magnesite to temperatures that remove the contained carbon dioxide. The finished product, therefore, is not magnesite at ali but simply a more or less pure magnesium oxide or magnesia. Furthermore, partly for statistical .and partly for commercial reasons, it has been customary, during recent years, to classify as "calcined magnesite" products that result from the heat-treatmerit of magnesium hydroxide precipitated from magnesium-containing brines; prod- ucts that, obviously, have no relationship whatever to magnesite. In the listing of magnesia-containing materials, tonnages of which are regularly reported by the Bureau of Mines, reports ordinarily are made under two headings: "caustic calcined" magnesite, in which all of the varieties of products treated at relatively low temperatures are lumped; and "dead-burned" magnesite, in which are included both high-purity and low-purity, and particularly both high-iron and irow-iron, materials that have been so heat-treated that the magnesium oxide occurs predominantly as crystalline periclase— materials used almost entirely for refractory purposes. In 1940 the apparent domestic consumption of "caustic calcined" magnesite was approximatcly 17,000 tons, "bout 95 Per cent of which was produced in this country. The apparent consumption of "dead-burned" magnesite was approximately 172,000 tons, some 82 per cent of which was domestically produced. In both total quantity and percentage of material produced within the United States, these figures are record highs for manY Years past. Utilization As indicated by these figures, the major tonnage outlet for magnesia is the refractories industry, in which magnesia is employed principally in three ways: (1) as dead-burned grain magnesite for the construction and maintenance of the hearths Or bottomS of basic open-hearth furnaces; (2) in the form of refractory magnesite bricks and shapes; and (3) as a chemical

Jan 1, 1942

By Max Y. Seaton

The scope of this paper will be limited to finished materials that contain a large preponderance (around 80 per cent or more) of magnesium oxide. The large and commercially important production of refractory dolomite and modified dolomites is not discussed here, and the production of magnesium basic carbonate for use as a heat insulator is barely mentioned. The discussion is confined mainly to magnesias produced in comparatively great quantity by direct processing of naturally occurring raw materials and hence excludes secondary or highly purified products such as pharmaceutical products or U.S.P. light and heavy calcined magnesias of commerce. Nomenclature The nomenclature of the magnesia products that will be discussed is somewhat confusing, in that it is customary in the trade to designate as "calcined magnesite" the materials that result from the calcining of magnesite to temperatures that remove the contained carbon dioxide. The finished product, therefore, is not magnesite at ali but simply a more or less pure magnesium oxide or magnesia. Furthermore, partly for statistical .and partly for commercial reasons, it has been customary, during recent years, to classify as "calcined magnesite" products that result from the heat-treatmerit of magnesium hydroxide precipitated from magnesium-containing brines; prod- ucts that, obviously, have no relationship whatever to magnesite. In the listing of magnesia-containing materials, tonnages of which are regularly reported by the Bureau of Mines, reports ordinarily are made under two headings: "caustic calcined" magnesite, in which all of the varieties of products treated at relatively low temperatures are lumped; and "dead-burned" magnesite, in which are included both high-purity and low-purity, and particularly both high-iron and irow-iron, materials that have been so heat-treated that the magnesium oxide occurs predominantly as crystalline periclase— materials used almost entirely for refractory purposes. In 1940 the apparent domestic consumption of "caustic calcined" magnesite was approximatcly 17,000 tons, "bout 95 Per cent of which was produced in this country. The apparent consumption of "dead-burned" magnesite was approximately 172,000 tons, some 82 per cent of which was domestically produced. In both total quantity and percentage of material produced within the United States, these figures are record highs for manY Years past. Utilization As indicated by these figures, the major tonnage outlet for magnesia is the refractories industry, in which magnesia is employed principally in three ways: (1) as dead-burned grain magnesite for the construction and maintenance of the hearths Or bottomS of basic open-hearth furnaces; (2) in the form of refractory magnesite bricks and shapes; and (3) as a chemical

Jan 1, 1942

By J. D. Shaw, E. B. Gebert, D. O. Noel

It is, of course, expected that manufacture of the various metal powders should involve numerous methods adapted to the specific characteristics of the metals themselves. Several methods for powdering a particular metal may be available, but the physical characteristics of the powder as produced by the several methods may be quite different. In the final analysis, the application of the metal powder dictates the physical properties that the metal powder must possess, and this, to a very large extent, will determine which of several possible methods of manufacture is adopted. Sometimes powder of the same metal is produced by more than one method, each powder having specific characteristics that make it particularly suitable for its application. For purposes of classification, the various methods of powdering metals can be grouped as follows: 1. Machining. 2. Milling (by ball mills, stamps, attrition mills, etc.). 3. Shotting (pouring molten metal into water, air, etc.). 4. Granulation (by stirring molten metal while solidifying). 5. Atomizing (disintegrating by steam, compressed air, etc.). 6. Condensation of metal vapor. 7. Reduction of oxide powders. 8. Chemical precipitation. 9. Electrolytic deposition. 10. Sintering (for producing alloy powders). 11. Formation of an alloy followed by dissolving or otherwise removing one of the alloying constituents. Machining Turnings, cuttings, filings, etc., are, of course, produced as by-products in machine work of various kinds, and find certain applications as metal powders. For example, iron powder so produced is used extensively as a reducing or precipitating agent and as a constituent in certain hard-finish cements.

Jan 1, 1938

By D. O. Noel, E. B. Gebert, J. D. Shaw

It is, of course, expected that manufacture of the various metal powders should involve numerous methods adapted to the specific characteristics of the metals themselves. Several methods for powdering a particular metal may be available, but the physical characteristics of the powder as produced by the several methods may be quite different. In the final analysis, the application of the metal powder dictates the physical properties that the metal powder must possess, and this, to a very large extent, will determine which of several possible methods of manufacture is adopted. Sometimes powder of the same metal is produced by more than one method, each powder having specific characteristics that make it particularly suitable for its application. For purposes of classification, the various methods of powdering metals can be grouped as follows: 1. Machining. 2. Milling (by ball mills, stamps, attrition mills, etc.). 3. Shotting (pouring molten metal into water, air, etc.). 4. Granulation (by stirring molten metal while solidifying). 5. Atomizing (disintegrating by steam, compressed air, etc.). 6. Condensation of metal vapor. 7. Reduction of oxide powders. 8. Chemical precipitation. 9. Electrolytic deposition. 10. Sintering (for producing alloy powders). 11. Formation of an alloy followed by dissolving or otherwise removing one of the alloying constituents. Machining Turnings, cuttings, filings, etc., are, of course, produced as by-products in machine work of various kinds, and find certain applications as metal powders. For example, iron powder so produced is used extensively as a reducing or precipitating agent and as a constituent in certain hard-finish cements.

Jan 1, 1938

By H. W. Hindry

This paper presents the ingredients com-~osing a type of oil-base mud that has been successfully used in drilling oil horizons in California, the effect of ingredient concentrations on physical properties, methods of handling at the well and possible advantages of a waterless drilling fluid with excellent plastering properties. Introduction An oil-base mud is a rotary drilling fluid in which oil has been substituted for water as the principal liquid ingredient. In recent years such a mud has been developed and used successfully for drilling the oil horizons of wells in various Calilornia fields. There are several types of oil-base mud, but only the type that is currently used to any appreciable extent will be considered at this time. The oil-base drilling-mud compositions used by Shell Oil Company, Incorporated have been covered by several patent applications on which patents are expected to issue at an early date. The purpose of this paper is to present data on the fundamental design of the mud; the ingredients used and their specifications; the effect of ingredient concentration on physical properties; the selection of the proper mud; the facilities needed for handling the mud; and a general discussion on drilling with oil-base mud. In view of the early stage of development of oil-base mud, the great number of vari- ables, and the almost unlimited possible combinations of these. variables, which in turn require extensive laboratory study, there are certain irregularities and omis. sions in the data presented here. However, it is believed that sufficient data are at hand to permit a fairly complete analysis of the characteristics of oil-base muds. In view of the excellent plastering properties of oil-base mud when properly proportioned, its use should: (I) minimize the possibility of impairing the natural flow potentialities of the producing horizon such as that resulting from infiltration of water from water-base muds; (2) permit smaller clearances for setting liners, since the mud sheath has no appreciable thickness; (3) eliminate the possibility of clogging the perforations of the liner with thick mud sheath; (4) facilitate the removal of the mud sheath from the walls of the hole, for its mud sheath has no appreciable strength; (5) assist in drilling through formations, such as "heaving shale," where water wetting appears to be a source of difficulty. (6) permit cores to be obtained without contamination from drilling water. Fundamental Design of an Oil-base Mud In the design of any rotary drilling mud it is necessary to select materials that will fulfill the following requirements: (I) act as the liquid medium and regulate the viscosity; (2) impart initial and final plastering properties; (3) give gel strength and structure in order to prevent settling; (4) serve as a weighting material. The

Jan 1, 1941

By H. W. Hindry

This paper presents the ingredients com-~osing a type of oil-base mud that has been successfully used in drilling oil horizons in California, the effect of ingredient concentrations on physical properties, methods of handling at the well and possible advantages of a waterless drilling fluid with excellent plastering properties. Introduction An oil-base mud is a rotary drilling fluid in which oil has been substituted for water as the principal liquid ingredient. In recent years such a mud has been developed and used successfully for drilling the oil horizons of wells in various Calilornia fields. There are several types of oil-base mud, but only the type that is currently used to any appreciable extent will be considered at this time. The oil-base drilling-mud compositions used by Shell Oil Company, Incorporated have been covered by several patent applications on which patents are expected to issue at an early date. The purpose of this paper is to present data on the fundamental design of the mud; the ingredients used and their specifications; the effect of ingredient concentration on physical properties; the selection of the proper mud; the facilities needed for handling the mud; and a general discussion on drilling with oil-base mud. In view of the early stage of development of oil-base mud, the great number of vari- ables, and the almost unlimited possible combinations of these. variables, which in turn require extensive laboratory study, there are certain irregularities and omis. sions in the data presented here. However, it is believed that sufficient data are at hand to permit a fairly complete analysis of the characteristics of oil-base muds. In view of the excellent plastering properties of oil-base mud when properly proportioned, its use should: (I) minimize the possibility of impairing the natural flow potentialities of the producing horizon such as that resulting from infiltration of water from water-base muds; (2) permit smaller clearances for setting liners, since the mud sheath has no appreciable thickness; (3) eliminate the possibility of clogging the perforations of the liner with thick mud sheath; (4) facilitate the removal of the mud sheath from the walls of the hole, for its mud sheath has no appreciable strength; (5) assist in drilling through formations, such as "heaving shale," where water wetting appears to be a source of difficulty. (6) permit cores to be obtained without contamination from drilling water. Fundamental Design of an Oil-base Mud In the design of any rotary drilling mud it is necessary to select materials that will fulfill the following requirements: (I) act as the liquid medium and regulate the viscosity; (2) impart initial and final plastering properties; (3) give gel strength and structure in order to prevent settling; (4) serve as a weighting material. The

Jan 1, 1941

By T. F. Baily

During the period of the war, in both this country and Canada, a number of attempts were made to make pig iron from steel scrap in the electric furnace, and a considerable tonnage of white pig iron was produced, the silicon and manganese additions being made with ferroalloys; but it is believed that the experiments conducted. at Canton, Ohio, in

Jan 1, 1930

By Charles Hart

The art of electric smelting came with the turn of the present century and owes its existence to the introduction of alternating current, which found its first wide use in the establishment of the great power plants at Niagara Falls, N. Y. Prior to that time current was largely direct. The furnaces were electrolytic in nature and found their first metallurgical use in the production of aluminum, and this process still prevails. The normal production of pig iron up to that time was carried on in blast furnaces in which charcoal, coke and anthracite were used as the fuel. This new electric process called for sufficient carbonaceous material to reduce the oxides and impregnate the pig iron with sufficient carbon, but the remainder of the energy was to be supplied by electric power. The chemical reactions are essentially the same in electric smelting as obtains in the older blast furnace. All of these data are so well known in both methods as to need no discussion at this time, for they can be found in scientific : publications and books written during the first two decades of this century. Types of Furnaces The 40 years devoted to the practice of electric smelting may be divided into two . periods of 20 years each. The first was devoted to experimentation with furnace types and with many publications on theories and processes. The second half of this term was devoted to perfecting the types of furnaces and their active commercial operation. The arc furnace may be found in three types: (1) the direct-heating arc furnace with the positive electrode included in the bottom and the other electrode suspended above; (2) the independent arc furnace with its electrodes entirely above the charge, which of necessity depends upon heat reflected from the roof; (3) the direct-heating series arc furnace equipped with two or more electrodes suspended from the roof. Of these three types, only the last is used in electric smelting of iron ore at the present time. The elimination of the other types automatically removed many of the early designs, to the end that there are now only two general types in operation: (I) the " Electrometalls" or high-shaft furnace of Sweden, and (2) the low-shaft or pit-type furnace as offered by Tysland-Hole and Siemens-Halske. The "Electrometalls" furnace takes its name from the corporation formed by the engineers that had undertaken its perfection. After trying several designs they brought forward the furnace shown in Fig. I, which by the way is the highest development of this type of furnace as of today.l Note the trend in the lines, which have kept pace with modern blast-furnace design. The high-shaft furnace lends itself to skip filling and is fitted with tuyeres immediately under the crucible roof, whereby the gases are recycled and the roof preserved. The failure of the Electrometalls furnace in Norway, because of its inability to meet

Jan 1, 1941

By Charles Hart

The art of electric smelting came with the turn of the present century and owes its existence to the introduction of alternating current, which found its first wide use in the establishment of the great power plants at Niagara Falls, N. Y. Prior to that time current was largely direct. The furnaces were electrolytic in nature and found their first metallurgical use in the production of aluminum, and this process still prevails. The normal production of pig iron up to that time was carried on in blast furnaces in which charcoal, coke and anthracite were used as the fuel. This new electric process called for sufficient carbonaceous material to reduce the oxides and impregnate the pig iron with sufficient carbon, but the remainder of the energy was to be supplied by electric power. The chemical reactions are essentially the same in electric smelting as obtains in the older blast furnace. All of these data are so well known in both methods as to need no discussion at this time, for they can be found in scientific : publications and books written during the first two decades of this century. Types of Furnaces The 40 years devoted to the practice of electric smelting may be divided into two . periods of 20 years each. The first was devoted to experimentation with furnace types and with many publications on theories and processes. The second half of this term was devoted to perfecting the types of furnaces and their active commercial operation. The arc furnace may be found in three types: (1) the direct-heating arc furnace with the positive electrode included in the bottom and the other electrode suspended above; (2) the independent arc furnace with its electrodes entirely above the charge, which of necessity depends upon heat reflected from the roof; (3) the direct-heating series arc furnace equipped with two or more electrodes suspended from the roof. Of these three types, only the last is used in electric smelting of iron ore at the present time. The elimination of the other types automatically removed many of the early designs, to the end that there are now only two general types in operation: (I) the " Electrometalls" or high-shaft furnace of Sweden, and (2) the low-shaft or pit-type furnace as offered by Tysland-Hole and Siemens-Halske. The "Electrometalls" furnace takes its name from the corporation formed by the engineers that had undertaken its perfection. After trying several designs they brought forward the furnace shown in Fig. I, which by the way is the highest development of this type of furnace as of today.l Note the trend in the lines, which have kept pace with modern blast-furnace design. The high-shaft furnace lends itself to skip filling and is fitted with tuyeres immediately under the crucible roof, whereby the gases are recycled and the roof preserved. The failure of the Electrometalls furnace in Norway, because of its inability to meet

Jan 1, 1941

By David R. Mitchell

This paper is limited primarily to a description of dry coal-cleaning processes in which air currents are used to effectuate a separation between coal and refuse. Processes depending mainly on differences in the coefficient of friction, resilience and shape are not described unless the use of air is necessary for the proper functioning of the process. The air cleaning of coal is of primary importance to the coal industry of the United States. From figures presented in the 1941 edition Mechannual, it is estimated that at least 12 million tons of bituminous coal was cleaned in the United States during 1940 by machines using air as the separating medium. One of the current problems confronting the coal-preparation engineer is the dry cleaning of small sizes and slacks. Progress in machine development for the cleaning of small sizes has been slow in recent years in the United States of America; it has been much more rapid in Britain and on the European continent. This paper does not attempt an exhaustive survey of all these developments, and only machines and processes that have found considerable commercial application are cited. Further, no critical analysis has been made of the theory involved in the separation of coal from refuse by processes using air as the separating medium other than that necessary for an understanding of particular machine designs and applications. The possibility of using air for the separation of coal from refuse was recognized early by mining men and many attempts were made to develop commercial machines. The ingenuity of the early experimenters is to be marveled at in view of their lack of knowledge of the theoretical principles involved. As in other arts, practice has largely preceded theory. Yet, science and practice play a game of leap frog, now one ahead, then the other; the careful experimenmenter governs his efforts along practical lines by adapting his experiments to the limits prescribed by scientific laws. By first studying developments and the theory involved, it is not only possible to adapt processes to new uses but also to reduce materially operating cost and to build larger units without costly failures. Although many inventors have applied for patents for separating minerals by the use of air currents, the literature in regard to coal is meager. Berrisford2 describes briefly some of the early attempts to clean coal without the use of water. Several of the examples cited by him are reproduced herein. Fig. I shows a machine used for grinding and; izing, in which rollers running in a pan with a perforated bottom and fan opening on the side crushed the coal, which was then carried by the air currents to a settling chamber. The heaviest particles dropped out first and the light ones farthest away, as shown. In the year 1864, a machine was made that could be used as a sizer or to separate dirt from coal with a sized feed (Fig. 2).

Jan 1, 1942

By David R. Mitchell

This paper is limited primarily to a description of dry coal-cleaning processes in which air currents are used to effectuate a separation between coal and refuse. Processes depending mainly on differences in the coefficient of friction, resilience and shape are not described unless the use of air is necessary for the proper functioning of the process. The air cleaning of coal is of primary importance to the coal industry of the United States. From figures presented in the 1941 edition Mechannual, it is estimated that at least 12 million tons of bituminous coal was cleaned in the United States during 1940 by machines using air as the separating medium. One of the current problems confronting the coal-preparation engineer is the dry cleaning of small sizes and slacks. Progress in machine development for the cleaning of small sizes has been slow in recent years in the United States of America; it has been much more rapid in Britain and on the European continent. This paper does not attempt an exhaustive survey of all these developments, and only machines and processes that have found considerable commercial application are cited. Further, no critical analysis has been made of the theory involved in the separation of coal from refuse by processes using air as the separating medium other than that necessary for an understanding of particular machine designs and applications. The possibility of using air for the separation of coal from refuse was recognized early by mining men and many attempts were made to develop commercial machines. The ingenuity of the early experimenters is to be marveled at in view of their lack of knowledge of the theoretical principles involved. As in other arts, practice has largely preceded theory. Yet, science and practice play a game of leap frog, now one ahead, then the other; the careful experimenmenter governs his efforts along practical lines by adapting his experiments to the limits prescribed by scientific laws. By first studying developments and the theory involved, it is not only possible to adapt processes to new uses but also to reduce materially operating cost and to build larger units without costly failures. Although many inventors have applied for patents for separating minerals by the use of air currents, the literature in regard to coal is meager. Berrisford2 describes briefly some of the early attempts to clean coal without the use of water. Several of the examples cited by him are reproduced herein. Fig. I shows a machine used for grinding and; izing, in which rollers running in a pan with a perforated bottom and fan opening on the side crushed the coal, which was then carried by the air currents to a settling chamber. The heaviest particles dropped out first and the light ones farthest away, as shown. In the year 1864, a machine was made that could be used as a sizer or to separate dirt from coal with a sized feed (Fig. 2).

Jan 1, 1942

By Paul D. Merica

Jan 1, 1937

By Earl S. Greiner, Bradley Stoughton

As a part of the systematic study of the alloys of iron under the auspices of the Engineering Foundation, and preliminary to the commencement of comprehensive work on this larger subject, the authors have undertaken an investigation of the available literature dealing with the alloys of iron and silicon. The purpose is to collect all the data in English and foreign languages and present them in two monographs, one of a more scientific and the second of a more industrially useful nature. Of course, a great deal of information upon the constitution of the iron-silicon alloys was found specificially upon the changes of phase in the equilibrium diagram and the different phases present, such as solid solution, chemical compounds (iron silicides), etc. While no extended research was contemplated in the particular study undertaken, nevertheless the data collected proved to be so contradictory in many respects that a simple study of some of the outstanding problems involved in the constitution and equilibrium diagram was undertaken. Because research was not a primary object of the work, and also because of the extreme industrial importance of the silicon alloys between 0.80 and 14 per cent. silicon, and finally because of the unsatisfactory state of knowledge existing as to these alloys, the experimental investigation was limited entirely to alloys with less than 10 per cent. silicon. Discussion oF Continuous Series It has often been said in print that the iron-silicon alloys form a continuous series of solid solutions from 0 to 15 per cent. silicon. This claim the authors are inclined to doubt: first, because the alloys from 0 to 4.25 per cent. silicon are ductile and malleable at atmospheric temperature, while those with 5 per cent. or more of silicon are comparatively hard and brittle. Furthermore, the alloys with more than 4.25 per cent. silicon are comparatively hard and low in ductility at atmospheric temperature, but become much more ductile when heated slightly. It is well known, for example, that the alloy containing 4.75

Jan 1, 1930

By George F. Comstock

It has been reported recently1 that the hardenability and toughness of forging steels may be improved appreciably by the use of complex deoxidizers containing titanium, aluminum, and vanadium. In the light of these results, an investigation of similar deoxidizers containing various hardening and grain-refining elements was proposed. These deoxidizers included three manganese-silicon-aluminum-titanium al- loys with and without boron and calcium, three titanium-aluminum ferroalloys with vanadium, molybdenum and zirconium, respectively, an aluminum-zirconium ferroalloy, and plain ferroboron. Their approximate compositions are given in Table I, and the results obtained so far in the investigation of their effects on steel are presented in the later parts of this paper. Method of Using Deoxidizers The deoxidizers listed in Table I were used in three series of 0.40 per cent carbon steels, which were melted in a small basic-lined induction furnace and cast in the form of I7-lb. ingots about 2.75 in. square. The basic charge for each heat was 10 lb. Armco iron and 6 lb. of clean low-carbon sheet-steel scrap. When melted, this charge was deoxidized with 15 grams of ferrosilicon, then about 500 grams of pig iron was added to give the desired carbon content. After the pig iron was dissolved, nickel shot and high-carbon ferrochromium were added if required, and additions of 80 per cent high-carbon ferromanganese and 50 per cent ferrosilicon were made to provide the proper amounts of those elements. Aluminum was added to every heat 2 min. after the silicon, for grain-size control and preliminary deoxidation. One minute later the special deoxidizer was added to the clean bare surface of the molten steel, and 2 min. afterward the steel was poured into the ingot mold, using a hot-top and pipe-preventing compound after pouring to decrease the depth of the shrinkage cavity. The special deoxidizers were used mostly in the form of about ½ to¾-in. lumps,

Jan 1, 1942

By George F. Comstock

It has been reported recently1 that the hardenability and toughness of forging steels may be improved appreciably by the use of complex deoxidizers containing titanium, aluminum, and vanadium. In the light of these results, an investigation of similar deoxidizers containing various hardening and grain-refining elements was proposed. These deoxidizers included three manganese-silicon-aluminum-titanium al- loys with and without boron and calcium, three titanium-aluminum ferroalloys with vanadium, molybdenum and zirconium, respectively, an aluminum-zirconium ferroalloy, and plain ferroboron. Their approximate compositions are given in Table I, and the results obtained so far in the investigation of their effects on steel are presented in the later parts of this paper. Method of Using Deoxidizers The deoxidizers listed in Table I were used in three series of 0.40 per cent carbon steels, which were melted in a small basic-lined induction furnace and cast in the form of I7-lb. ingots about 2.75 in. square. The basic charge for each heat was 10 lb. Armco iron and 6 lb. of clean low-carbon sheet-steel scrap. When melted, this charge was deoxidized with 15 grams of ferrosilicon, then about 500 grams of pig iron was added to give the desired carbon content. After the pig iron was dissolved, nickel shot and high-carbon ferrochromium were added if required, and additions of 80 per cent high-carbon ferromanganese and 50 per cent ferrosilicon were made to provide the proper amounts of those elements. Aluminum was added to every heat 2 min. after the silicon, for grain-size control and preliminary deoxidation. One minute later the special deoxidizer was added to the clean bare surface of the molten steel, and 2 min. afterward the steel was poured into the ingot mold, using a hot-top and pipe-preventing compound after pouring to decrease the depth of the shrinkage cavity. The special deoxidizers were used mostly in the form of about ½ to¾-in. lumps,

Jan 1, 1942

By Earnshaw Cook, J. A. Fellows, Howard S. Avery

Heat-resistant alloys of the higher nickel and chromium ranges have been empirically developed through the practical experience of the past two decades to a position of significant industrial importance. Few quantitative metallurgical data have been published, however, that could be related directly to engineering specifications and design. Inadequate information led to the inauguration, in 1934, of a research directed toward a better understanding of the properties and performance of these steels at temperatures between 1400° and 2000°F. Investigation was concentrated upon the 26 per cent Cr:I2 per cent Ni type, which owes its extensive application to an excellent combination of economy, strength and surface stability at elevated temperatures. The requirements of the oil-refining industry have been prominent in influencing the scope and evolution of the program. Creep strength at the maximum allowable deformation ranges has been employed to evaluate the merits of these alloys. Permissible elongation rates vary from 1.0 per cent in one million hours for turbine blades to I .o per cent in ten thousand hours for tube supports and heating-furnace equipment. Throughout this paper, the limiting creep stress (L.C.S.) for a given temperature has been defined as the stress that will produce a uniform elongation rate (stage 11) of one per cent in ten thousand hours as extrapolated from rates per hour for tests of less than two thousand hours duration. Certain current specifications require a minimum L.C.S. of 1600 lb. per sq. in. at I800°F., of 3600 lb. per sq. in. at 1400°F., and include a tensile acceptance test at room temperature, after aging for 24 hr. at 1400°F., as a measure of embrittlement in service. An elongation of 4 per cent is considered satisfactory for general use, while a minimum of 9 per cent is prescribed on occasion. Many differences of opinion concerning the properties and performance of these alloys appear to result from their sensitivity to unappreciated variations of chemical analyses which, for example, may change their L.C.S. from 3500 to 350 lb. per sq. in. at 1800°F. Within broad chemical limits, it is possible to balance the six or more important elements present to attain desirable properties with a number of different combinations. One method for adjusting the composition has been described under the sponsorship of the Alloy Casting Institute,' in which, by maintaining a substantially austenitic* alloy, optimum creep strength and minimum tendency to embrittle after aging are expected. Unless, however, the limits are undesirably close, it has not been possible to ensure a moderate range of strength and of ductility by any chemical specification alone. There is a definite need

Jan 1, 1942

By J. A. Fellows, Earnshaw Cook, Howard S. Avery

Heat-resistant alloys of the higher nickel and chromium ranges have been empirically developed through the practical experience of the past two decades to a position of significant industrial importance. Few quantitative metallurgical data have been published, however, that could be related directly to engineering specifications and design. Inadequate information led to the inauguration, in 1934, of a research directed toward a better understanding of the properties and performance of these steels at temperatures between 1400° and 2000°F. Investigation was concentrated upon the 26 per cent Cr:I2 per cent Ni type, which owes its extensive application to an excellent combination of economy, strength and surface stability at elevated temperatures. The requirements of the oil-refining industry have been prominent in influencing the scope and evolution of the program. Creep strength at the maximum allowable deformation ranges has been employed to evaluate the merits of these alloys. Permissible elongation rates vary from 1.0 per cent in one million hours for turbine blades to I .o per cent in ten thousand hours for tube supports and heating-furnace equipment. Throughout this paper, the limiting creep stress (L.C.S.) for a given temperature has been defined as the stress that will produce a uniform elongation rate (stage 11) of one per cent in ten thousand hours as extrapolated from rates per hour for tests of less than two thousand hours duration. Certain current specifications require a minimum L.C.S. of 1600 lb. per sq. in. at I800°F., of 3600 lb. per sq. in. at 1400°F., and include a tensile acceptance test at room temperature, after aging for 24 hr. at 1400°F., as a measure of embrittlement in service. An elongation of 4 per cent is considered satisfactory for general use, while a minimum of 9 per cent is prescribed on occasion. Many differences of opinion concerning the properties and performance of these alloys appear to result from their sensitivity to unappreciated variations of chemical analyses which, for example, may change their L.C.S. from 3500 to 350 lb. per sq. in. at 1800°F. Within broad chemical limits, it is possible to balance the six or more important elements present to attain desirable properties with a number of different combinations. One method for adjusting the composition has been described under the sponsorship of the Alloy Casting Institute,' in which, by maintaining a substantially austenitic* alloy, optimum creep strength and minimum tendency to embrittle after aging are expected. Unless, however, the limits are undesirably close, it has not been possible to ensure a moderate range of strength and of ductility by any chemical specification alone. There is a definite need

Jan 1, 1942

By R. F. Miller, R. F. Campbell

Sixteen steels containing different combinations of chromium and molybdenum, in amounts up to 5 per cent of each element, were examined for microstructure and hardness after air cooling and after furnace cooling from suitable austenitizing temper- atures. Diagrams summarizing the structnres and hadness resulting from these two cooling rates are presented (Figs. 3, 4, 7).t Data were also obtained on the influence of these two elements, individually and in combination, on the depth of decarburiza-tion observed after furnace cooling (Fig. 8). Composition of Material The chemical composition of the steels investigated is given in Table I. The plain carbon steel was made in a 2 5-ton Heroult electric-are furnace, while the alloy steels were made in a 4.5-ton Ajax-Northrup elec- tric induction furnace. The cast ingots were hot-rolled to 1.75-in. bars. Air-cooled Series The I.75-in. bars were forged to flat plates, 0.25 in. thick, from which specimens 0.5 in. wide by 2 in. long were cut. The specimens were pretreated to improve their homogeneity by heating to 1830°F. (I000°C.) for 20 min. and oil-quenching. They were then reheated to 1740°F. (950°C.) for one hour and air-cooled, after

Jan 1, 1942

By R. F. Campbell, R. F. Miller

Sixteen steels containing different combinations of chromium and molybdenum, in amounts up to 5 per cent of each element, were examined for microstructure and hardness after air cooling and after furnace cooling from suitable austenitizing temper- atures. Diagrams summarizing the structnres and hadness resulting from these two cooling rates are presented (Figs. 3, 4, 7).t Data were also obtained on the influence of these two elements, individually and in combination, on the depth of decarburiza-tion observed after furnace cooling (Fig. 8). Composition of Material The chemical composition of the steels investigated is given in Table I. The plain carbon steel was made in a 2 5-ton Heroult electric-are furnace, while the alloy steels were made in a 4.5-ton Ajax-Northrup elec- tric induction furnace. The cast ingots were hot-rolled to 1.75-in. bars. Air-cooled Series The I.75-in. bars were forged to flat plates, 0.25 in. thick, from which specimens 0.5 in. wide by 2 in. long were cut. The specimens were pretreated to improve their homogeneity by heating to 1830°F. (I000°C.) for 20 min. and oil-quenching. They were then reheated to 1740°F. (950°C.) for one hour and air-cooled, after

Jan 1, 1942