Search Documents

By Nobuharu Isago, Atsushi Kusaka, Kosuke Kawata, Dohta Awaji

"The immediate ring closure method, in which the entire periphery of the excavation area is closed immediately with an initial support within a short distance from the excavation face, has been increasingly used in Japan, especially, as one of the most effective countermeasures against difficult ground conditions in conventional tunneling. For reasonable design of this method, the performance requirements for the initial support should be clearly stated. The analysis of construction data of 30 road tunnels and the three-dimensional numerical modeling based on real data suggest that the immediate ring closure stabilizes the tunnel structure and the ground around it because of the inner pressure effect of the initial support, especially, for low ground competence factor and small internal friction angle. Finally, the bending compressive strength and the cross-sectional geometry of the initial support have to be considered in the tunnel design while considering the earth pressure and ground properties. INTRODUCTION Conventional tunneling methods often deal with difficult ground conditions such as soft ground or squeezing ground conditions. The immediate ring closure method, in which the entire periphery of the excavation area is immediately supported within a short distance from the excavation face (Figure 1), has been increasingly used in Japan as one of the most effective countermeasures against difficult ground conditions in conventional tunneling (e.g. Takahashi et al., 2011; Nakaoka et al., 2013). The immediate ring closure method was empirically identified as effective for reducing ground surface subsidence and tunnel deformation. However, the working effects of the method have not been clarified sufficiently. To improve the design of this method, the working effects of this method and the performance requirements for the initial support need to be clarified. The relation between the effect of immediate ring closure and earth cover has been clarified (Mashimo et al., 2008; Awaji et al., 2013),"

Jan 1, 2016

By Vijaya Bhushan Rao, Jason Redgers

The typical Vibrocompaction projects undertaken in the UAE are on reclaimed Sands. These Sands which are predominantly the crushable, calcareous, carbonate sands found locally as opposed to the more common quartz or silica sands that are featured in most design literature. The famous reclamations such as the iconic Palm Jumeirah in Dubai, often have specification for mitigation of liquefaction induced settlements, bearing capacity increases and total and differential settlement requirements. Often these performance targets are achieved by the means of achieving a particular relative density that are generally measured by a defined Cone Penetration Test, CPT targeting values of cone resistance (Qc), MPa at respective depth zones. In this paper some case studies are presented, where soil suitability for deep compaction by vibratory methods was firstly assessed for suitability using the Massarsch, 1991 compactability chart prior to the application of vibrocompaction and its subsequent evaluation. One such project named the Island Development required 17 to 23m depth of penetration only to treat the lower 5 to 6m of sand above rockhead as eventually the top 15m of sand will be further excavated to allow for the construction of basement. The paper will present pre and post CPT results, the results of initial site calibration trials and evaluation of the completed works.

Oct 1, 2022

By Dan Brown

Deep foundation contracting for transportation projects in the United States has typically followed the design-bid-build model in which contractors bid on a specific work product according to relatively inflexible prescriptive specifications. With continuous flight auger piling and the many types of proprietary drilled displacement auger piling, there appear to be advantages to contracting this work according to a different model. This paper provides a discussion of the use of a performance specification for this work in which the contractor has greater freedom to choose the most appropriate foundation system and also greater responsibility for the performance of the completed foundation. With public agencies subject to open bidding, this type of contractual arrangement presents opportunities to encourage innovation. There are also challenges for implementation in public works projects, notably the selection of qualified contractors and the verification of performance requirements on production foundations.

Jan 1, 2006

By W. E. Sabina

In the short period of one mans? career we have seen specifications for bulk material handling systems and equipment grow from two or three pages to as much as two or three volumes for a single contract. The old 'short form' described what the purchaser expected the equipment to do. The long form does the same but also includes nut, bolt, and lockwasher depth of detail. What are the events that led to this proliferation of verbiage, and does it benefit the buyer in the final analysis? Is there a better way to purchase complex equipment while ensuring the highest quality for the dollar spent?

Jan 1, 1986

By William E. Bruce

Percussive drill calibration experiments performed by the Bureau of Mines on two drills are described. The use of a linear velocity transducer to determine piston velocity, blow frequency, and piston stroke length is discussed. Data are presented on the relationships between maximum work rate and feed air pressure. Penetration rates in nine rock types were measured for the same two drills. Physical properties of the nine rock types are presented in tabular and graphical form to show relationships between penetration rates and physical properties. Finally, conclusions are drawn as to the potential use of these data to predict percussive drilling rates.

Jan 1, 1970

By Gurubasayya Swamy

This paper presents the performance study of sag mill in the processing of gold ore. Deterioting ore grade and high demand of metals has tremendously influenced the SAG mills. Today?s high capacity Semi-autogenous grinding (SAG) mills expand vast amounts of energy and in doing so consume tons of shell liners and steel balls, while processing ore. Semi-autogenous (SAG) mill performance is influenced by ball charge, feed properties, shell, grate, and pulp lifter design. In the performance study of SAG mill, based on the results obtained it can be observed that SAG mill performed better at feed size +4 inch and grinding media consumption 0.90kg/mt. In the present study the effect of crusher bypass on SAG mill performance, an immediate drop of throughput ranging from 10-20tph is observed. Keywords: sag mill, pulp lifters, grinding media, energy, consumption, throughput

Sep 1, 2012

By Jack V. Hill

A unique type of grinding mill liner has been developed by Waagner-Biro A.G. of Austria. This liner system, termed an angular spiral lining (.ESL), was, successfully tested by Magma Copper Company's San Manuel concentrator in both their 10 Ft x 10 Ft (3.05m x 3.05m) and 12 Ft, 6 In x 14 Ft (3.81m x 4.27m) grate discharge wet grinding ball mills. Magma Copper's savings in power and grinding balls justified conversion of more than half of their twenty-six ball mills to the ESL system.1,2 The ASL system was provided by the Capitol Castings Division of Midland Ross Corporation, the exclusive licensee for such conversions. Capitol Castings proposed the following as expected benefits from installation of an ASL system in an 18 Ft x 21 Ft (5.49m x 6.40m) overflow discharge wet grinding ball mill at the Pinto Valley Operation of Cities Service Company: "(a) Reduction of power consumption per ton of ore milled = 12%, (b) Increased throughput = 6%, (c) Reduction of ball consumption = 6%."

Jan 1, 1982

By T. Fraser, R. L. Sutherland

Under a cooperative agreement between United States Bureau of Mines and the Truax-Traer Coal Company, some operating-scale experiments have been made with the cyclone thickener in the preparation plant of the Shamrock No. 1 mine at Kayford, West Virginia. These tests were made with a 14-in. cyclone of the type developed by the Dutch State Mines in Limburg. It was applied experimentally to the thickening of solids in washery water to obtain performance data to show the range of sizes that may be recovered and other operating characteristics that would indicate the field of usefulness of this device in coal preparation practice. This is a progress report only. It covers results obtained in a series of 17 tests of the operation of what has been considered a unit of commercial size operating on suspensions of fine coal mixed with a relatively small amount of freeimpurities. The underflow material, after further dewatering in centrifuges, is a marketable grade of coal.

Jan 1, 1949

By R. E. Wilmot

This paper is based on the experiences, over many years, of numerous authors in the South African mining industry and of the hot dip galvanizing process and its application as a corrosion protection system. The paper sets out the extensive development, financial resources and stringent operating requirements of the South African mining industry. After many years of research and operational experiences, hot dip galvanizing and, when necessary, duplex systems, have been found to meet the demanding requirements of this particular industry. The paper sets out the requirements from the standpoint of corrosion criteria and is followed with a case where the corrosion protection properties of hot dip galvanizing are demonstrated. This case history traces the early investigation of the expected corrosive conditions in a new mining operation and concludes with two follow-up visits to the mine in order to examine actual performance of the corrosion protection system after ten years in service.

Jan 1, 2007

By R. E. Wilmot

This paper is based on the experiences, over many years, on the part of numerous authors in the South African mining industry and that of the hot dip galvanizing process and its application as a corrosion protection system. The paper sets out the extensive development, financial resources and stringent operating requirements of the South African mining industry. After many years of research and operational experiences, hot dip galvanizing and when necessary, duplex systems, have been found to meet the demanding requirements of this particular industry. The paper sets out the requirements from the standpoint of corrosion criteria and is followed with a practical example; ?case history? where the corrosion protection properties of hot dip galvanizing are demonstrated. This case history traces the early investigation of the expected corrosive conditions to be encountered in a new mining operation (now 10 years on) and concludes with two follow up visits to the mine in order to examine actual performance of the corrosion protection system after ten years in service.

Jan 1, 2006

By Haijian Fan

Currently, deep foundation designs for the service limit state are deterministic in nature. The settlements and lateral deflections of deep foundations are calculated by means of numerical techniques whereby the foundation-soil interactions are characterized by discrete load transfer curves such as t-z or p-y curves. The noted deficiency of the deterministic approach is that the uncertainties arising from various sources, such as soil properties and model errors are not considered. To address this deficiency, a performance-based reliability design methodology is developed using Monte Carlo statistical methods. The performance based design criteria are defined in terms of the specified allowable displacement. The input to the numerical solution techniques, including the soil strength parameters, unit weight of the soil are relevant to the generation of the load transfer curves are treated as random field. The well established random field generator algorithm, local averaging subdivision, is used to generate random samples of input, where the mean values, variances, the probability distribution, and correlation structures are required statistical parameters for these random variables. The objective of the performance based reliability design is to determine the optimized foundation dimensions so that the probability of failure is less than the target probability of failure. The probability of failure by the Monte Carlo approach is simply the ratio of the number of unsatisfactory performance to the sample size. A numerical example for laterally loaded drilled shaft is given to illustrate the application of the methodology. The incorporation of the correlation length is shown to be critical for properly accounting for the site soil spatial variability.

By Haijian Fan

Currently, deep foundation designs for the service limit state are deterministic in nature. The settlements and lateral deflections of deep foundations are calculated by means of numerical techniques whereby the foundation-soil interactions are characterized by discrete load transfer curves such as t-z or p-y curves. The noted deficiency of the deterministic approach is that the uncertainties arising from various sources, such as soil properties and model errors are not considered. To address this deficiency, a performance-based reliability design methodology is developed using Monte Carlo statistical methods. The performance based design criteria are defined in terms of the specified allowable displacement. The input to the numerical solution techniques, including the soil strength parameters, unit weight of the soil are relevant to the generation of the load transfer curves are treated as random field. The well established random field generator algorithm, local averaging subdivision, is used to generate random samples of input, where the mean values, variances, the probability distribution, and correlation structures are required statistical parameters for these random variables. The objective of the performance based reliability design is to determine the optimized foundation dimensions so that the probability of failure is less than the target probability of failure. The probability of failure by the Monte Carlo approach is simply the ratio of the number of unsatisfactory performance to the sample size. A numerical example for laterally loaded drilled shaft is given to illustrate the application of the methodology. The incorporation of the correlation length is shown to be critical for properly accounting for the site soil spatial variability.

Jan 1, 2017

By Stefan Planeta

On discute les performances techniques et économiques des méthodes d'exploitation à haut rendement dans les mines métallifères au Canada. L'accent est mis sur la dilution et pertes des réserves minières et sur les coûts opératoires et totaux. Une analyse technique de quelques opérations minières est également effectuée. Il ressort de cette analyse que les résultats réels des opérations minières en cours diffèrent souvent de ces planifiés suite à la dilution du minerai et aux pertes importantes des réserves minières. On propose, définit et discute un certain nombre des facteurs de performances technologiques et économiques pour pouvoir mieux apprécier les problèmes rencontrés dans plusieurs mines en opération. À l'aide des études de cas on démontre impact négatif de la dilution et des pertes additionnelles des réserves minières sur la rentabilité des opérations en cours et sur les nouveaux projets miniers. On conclut, que l'application des indicateurs proposés donnerait un outil valable, aux opérateurs miniers, aux niveaux de la planification, du suivi des travaux d'exploitation et d'éventuelles études comparatives entre les différentes situations minières. ABSTRACT The paper discusses technical and cost performance of bulk mining methods in Canadian U/G metal mines. It focuses on ore dilution, ore reserves losses as well as on operational and total cost. Technical analysis of some mining operations has been performed. It indicates that due to dilution and significant reserves losses, the actual results of mining operations often differ substantially from those planned. The paper proposes, defines and discusses several indicators quantifying technical and economical performance in order to assess better the problems encountered in several operating mines. The case studies presented here have demonstrated an adverse effect of dilution and additional reserves losses onto profitability of existing operations and new mining projects. It is concluded that the application of the above mentioned indicators may be beneficial for mine operators. They may become a very useful tool at the stages of planning, follow-up of mining works and with regards to comparative studies between different mining situations.

May 1, 2001

By Glenn Tobin

The overarching goal in modern drill and blasting operations is that of optimising mining operations to achieve higher levels of productivity, safety, profitability and sustainability. Air decking, a technique used in drill & blasting to optimise explosive product use while achieving a target rock fragmentation1, is a technique that when executed correctly is proven to achieve consistent results independent of rock strength and the position of the holes (single, multiple, vertical, slanted), as well as being proven to reduce super-fragmentation (under-size or fines) while able to achieve optimal fragmentation, especially in the stemming zone2. The ‘shock absorber effect’ if the air deck reduces ground vibration and air blast3. Additionally, the practice of loading explosive product directly in saturated ground without dewatering or lining prior is an increasing global trend.

Jan 1, 2012

By A. P. Schissler

2013 has seen metals, industrial minerals, and coal all reduce in price due to market and geo-political factors. Many companies are taking write-downs to recalibrate their reserves and have enacted focused cost reduction programs. The public domain includes statements where companies have operating cost reduction goals in the $500 million range. Zero-base staffing & budget analysis is a means to achieve optimal employment and cost levels for a given level of production. The method involves measuring the work to be done similar to Lean. Lean is a method to review each step of production and remove anything that doesn?t add value or is necessary to complete finished goods. Zero-base methodology has been applied to mines worldwide producing realistic and sustainable levels of staffing and costs based on the quantity of work. The objective of this paper is to provide the framework of zero-basing with examples of application.

Feb 23, 2014

By Mazin Adnan

The 80m high dam at the Peribonka river in the Canadian province of Quebec was designed for the generation of 385 MW of hydro electrical power (Fig.1). The complex ground conditions required the employment of a variety of geotechnical construction methods stretched to limits never experienced before. Innovative grouting and trenching techniques were used for the construction of a plastic concrete cut-off wall down to a depth of about 116m, to cut hydraulic seepage through alluvial deposits forming the dam foundation. The bedrock where the cut-off wall is embedded forms a glacial gully with steeply sloped flanks, which created further challenging conditions. [ ]

Jan 1, 2008

By Leslie W. Austin

ROTARY kiln operators will agree that some of the most severe conditions a refractory must stand occur in the hot zone of a kiln burning Portland cement, dead burn dolomite, magnesite, periclase, and similar materials. Frequently the operator is faced with factors beyond his control which drastically shorten the life of refractories. Shutdown due to mechanical failure can be serious if the period is of sufficiently long duration to cause the dropping of coating or the loosening of the lining. A change in slurry can affect the coating and cause ring buildup. A change in type of fuel and its effect upon the flame can cause a shift in location of the hottest zone. Weekend shutdowns or any other interruption can cause the operator trouble and may damage the refractories, since stopping and starting a rotary kiln is certainly more difficult than stopping and starting a motor. Some operators have tried to set an estimate of damage for each shutdown in equivalent days of running time. Conditions affecting the refractory may be roughly grouped in four classes: chemical attack, mechanical stress, thermal shock, and abrasion. Chemical Attack: The drive to obtain maximum production through a kiln demands maximum operating temperatures, temperatures which are limited more by the ringing up or melting of the clinker. This can cause interface temperatures at the junction of coating and refractory which require the use of a basic kiln block to withstand the chemical attack. Chemical changes take place within the refractory itself, especially in chemically bonded or unburned kiln blocks: These changes cause the formation of the ceramic or burned bond. Migrating liquids or fluxes from the kiln charge have an effect within the refractory and lead to mineral or glass formation. The alkalies, sodium and potassium, migrate into the refractory as silicates, chlorides, sulphates or other salts. They may move under capillary action or may be caused to move by volatilization with condensation in the cooler portion. Mechanical Stress: Concentrated stress may be caused by several factors or combinations thereof. 1-The rings of refractories must be kept tight and rigid within the kiln, and this alone demands considerable force to hold the blocks in place. So that the force will not be concentrated, the blocks should fit the circle as perfectly as possible, with the faces in contact overall. 2-As the kiln is heated, thermal expansion takes place at the hot end of the kiln block. Since this disturbs the plane face it too can cause a concentrated stress at the two ends of the block, and shearing stress can be set up within the brick itself because of the difference in expansion between the two ends. 3-If a lining becomes loose and moves in the shell very severe stress can be set up, and as the kiln rotates this load changes and gives the effect of repeated loading. Permanent expansion of the refractory can also cause severe loading. 4-Not least important, flexing of the kiln is frequently the cause of concentrated stresses. Thermal Shock: Thermal shock, the result of heating and cooling too rapidly, occurs on starting and stopping or when a large patch of coating drops, exposing the bricks. Again, its destructive effect is often the result of phase change, liquid to solid or the reverse; dense refractories loaded with glass-forming impurities are particularly susceptible. Thermal shock is a problem with refractories set in the wall or roof of a stationary furnace, and becomes even more serious in a rotary kiln, the tendency to spall being magnified with movement and concentration of stress. Uniform rate of feed and loading insures both better coating and a more uniform stress. Abrasion: If the refractories do not take a coating, abrasion can become a most destructive factor. Movement of the lining in shell or movement of loose blocks causes abrasion, which is also most destructive if the refractories do not take a coating. An analysis of the problem of basic lining for the hot zone reveals, therefore, a number of desirable characteristics: high refractoriness, basic chemical reaction, resistance to spalling, good strength at all stages, ability to take coating, true sizing, volume stability, and abrasion resistance. Increased demand

Jan 1, 1952

By Paul Sterk

In underground mining a great deal of time, money, effort, and resources have been used in the effort to minimize blast-induced damage. This damage occurs to the back, ribs, and pillars when the energy of the explosive is released back into the rock due to over confinement or the overloading of explosives in the perimeter holes. This damage can result in roof falls, dilution of ore, excessive rock bolting, scaling, screening, shot-creteing and other safety and support issues.

Jan 1, 2003

By John Wall

The use of electronic detonators in civil tunnelling applications, to reduce vibration is small firings has been successfully utilised for a number of years. As part of the mining industry’s commitment to reducing blast damage during the development cycle in underground mining applications, a series of development blasts using eDevTM electronic detonators in typical mining applications was conducted in North Queensland, Australia.

Jan 1, 2012

By J Wall

The use of electronic detonators in civil tunnelling applications, to reduce vibration in small firings has been successfully utilised for a number of years. As part of the mining industry’s commitment to reducing blast damage during the development cycle in underground mining applications, a series of development blasts using e-Dev™ electronic detonators in a typical mining application was conducted at Resolute’s Mt Wright operations in North Queensland in 2010. Results were based on direct comparisons to the current industry standard of non-electric firings as a baseline, with as many parameters as possible being captured during the trial. Development costs are typically high in most underground mines, especially in capital development headings, which are in waste and therefore of no direct economic value, so by being able to accurately fire to design, costs relating to both ground support requirements and volume of material removed, (and therefore haulage required) can be minimised. A direct comparison of overbreak (ground blasted outside of design) and cast (distance rock thrown from blast) was also made during the trial, as well as close monitoring of the drilling accuracy.

Mar 21, 2011