Search Documents

By Y. Mitani, H. Ikemi, K. Kitamura, H. Honda

"Instead of carbon capture and geological storage (CCS) that does not rely on structural aquifers, injecting carbon dioxide into sedimentary rock deep underground has been considered. For advection velocity of the fluid is slow, the permeability of sedimentary rock deep underground is low. In order to perform the CCS on the low permeable sedimentary rock, it is necessary to clarify the behavior of long term storage properties of carbon dioxide (CO2).In this study, the permeability and storativity of CO2 injected into low permeable rock has been evaluated. The injection of supercritical CO2 has been conducted on the specimen of Ainoura sandstone (unit weight: 2.39 g/cm3, porosity: 11.9 %) saturated with water by using flow pump method. The experiment has been set up to reproduce the similar condition of deep underground reservoir under 20 MPa confining pressure, 10 MPa pore pressure, 35°C temperature and 3 µl/min CO2 injection rate. In order to prevent an increase in pore pressure, the boundary condition on the outlet side of specimen has been kept a constant pressure.As a result, it has been possible to observe step by step the change of the differential pressure between both ends of specimen. Furthermore, the relative permeability and specific storage of rock under supercritical CO2 injection has been examined by the theoretical analysis of flow pump permeability test incorporating Darcy’s law for two-phase flow. It is observed that CO2 has been transmitted gradually while CO2 stored in the rock. It is also clarified that residual water has existed in specimen after showing the constant differential pressure in the end of the experiment. Using the results of the experiment, 3D core-scale flow-simulation by using TOUGH2 has been conducted due to confirm the flow of fluid and CO2 distribution in the specimen. From the experimental results and analytical solution to them, permeability and storativity are identified, and simulation results support the validity of the experimental results."

Jan 1, 2015

By G. D. Monk, W. C. Krumbein

THE relation between permeability and the size parameters of unconsolidated sand is approached by considering sands as logarithmic frequency distributions having the basic parameters mean size and standard deviation. Sieve separates were mixed in accordance with the normal logarithmic probability law, so that the mean and standard deviation could be varied at will. Experiments were conducted in which one parameter was kept fixed and the other varied; in this manner the dependence of permeability on the individual parameters was evaluated. It was found that permeability can be expressed as the product of a power function of the mean size and an exponential function of the standard deviation.

Jan 1, 1942

By Chester R. McKee, Robert W. Terhune, Merle E. Hanson

The relationships describing the enhancement of permeability by firing explosives in boreholes have been derived and combined to yield permeability enhancement as, [ ] or the case in which the stress decays asymptotically as a power law kc and nc represent permeability and fracture density at the edge of the pulverized region near the cavity wall, f is a geometric attenuation factor, m is the dissipation due to real material effects, ko is the original permeability and rd is the scaled radius. This relationship has been compared with available measurements from the American nuclear shot "Hardhat", the French nuclear events in Hoggar granite and the chemical explosive shot in coal near Kemmerer, Wyoming. Significant correlation between this theory and the experimental measurement is observed. A comparison between single and multiple detonations shows that permeability enhancement falls off steeply near the shot; however enhancement can be considerable midway between two shots spaced 10 cavity radii apart. The degree to which enhancement, can be significant depends on material properties and fracture density. Porosity distribution from the explosive 1s the dominate parameter in permeability enhancement. Existing theories of permeability enhancement have also been reviewed.

Jan 1, 1976

By J D. St George

In this paper a laboratory investigation into the effect of confining stress, water content and gas desorption on coal permeability is presented. Of major significance is the effect of coal permeability on outburst occurrence and methane production, which is influenced by changes in stress. Test results indicated that the shrinkage of the coal matrix associated with desorption is greater than the coal matrix compressibility which will cause a reduction in the effective stress, hence increasing coal permeability.

Jan 1, 1998

By V. Loya

Metallic foams (MF) are relatively new materials with a combination of attractive properties (permeability, high surface area, thermal and chemical stability, etc,), They can be produced from different materials and can be manufactured using various processes, Due to their unique properties, they find applications in different sectors of engineering, such as energy absorption, filtration, heat dissipation, etc, For many applications, the permeability is an important parameter to characterize and optimize, Most of the recent literature on the subject studied the permeability in the low velocity range. The present study was carried out to have a better understanding of permeability for greater velocity ranges, An equipment was designed and built for this purpose, Pressure drop measurements were made across the thickness of open-cell nickel foams, Pore and window sizes were measured by image analysis on SEM micrographs, The experimental results are in relatively good agreement with the Hazen-Dupuit-Darcy model (R2>98%), The permeability is affected by pore size, porosity and the normalized projected area of the connecting pores (ie. windows).

Jan 1, 2005

By Clement K. Chase, Manuel R. Lastra

Introduction The choice of using a dump or heap leaching process or a fine grinding-agitation leaching process is based on the grade and tonnage of the ore body. Low grade ore and small tonnages are best treated by a low-cost method, such as dump or heap leaching. Permeability, however, is the critical factor in a successful leaching operation, regardless of tonnage or grade. Without permeability in the leach bed, no percolation, no dissolution, no extraction, and no success are possible. Solution delivery to the ore is also essential. Solute-to-mineral contact is a requisite. The solute must be effectively strong and not be depleted in active dissolvers, such as acid, ferric iron, cyanide, and oxygen. It must also be moving across the mineral to be dissolved. No pockets of stagnant solution can be allowed. A third factor is recovery of the now-dissolved metal in the pregnant liquor. All such liquor should be gathered at a reasonable metal concentration to make further pumping and processing worthwhile. Control and recovery of pregnant solutions are probably the most ignored factors of solution mining. This stage in recovery is historically where many operations either fail or become viable. Permeability A permeable heap is normally achieved by taking into account heap building/construction and agglomeration/pelletizing. Even though heap building is critical for good permeability, it will not be discussed here. It has been described in detail by others. Instead, this analysis will concentrate on agglomeration and pelletizing. Differences between agglomeration and pelletizing are emphasized. Agglomeration is referred to when small particles are being attached to larger particles -the ore presents a complete size distribution. On the other hand, pelletizing is a process where all particles are fine (less than 850)µm or 20 mesh), as with mill tailings. The difference is important from two points of view: • Mechanical devices used to achieve the desired attaching action; and • Binder dosages. Mechanical Devices Due to the absence of large particles that fines can become attached to, pelletizing should be done in a centrifugal-action-based device, such as an inclined rotating plate, a rotary drum, or a series of belt-transfer points. In agglomeration, large particles play a part as a natural nucleus for the attaching action of fines. Hence, a tumbling action as strong as for pelletizing is not required. Common methods to accomplish agglomeration include: • Cascade belt system with either all belts moving forward or some of them moving forward and at least one moving backward; • Combination of belt plus inclined vibrating chute; • Large concrete mixer drum; and • Belt discharging directly onto stockpiled ore. The proper agglomeration system will depend basically on the size distribution of the ore and the amount and type of clays present. In all of the agglomerating systems described, the tumbling action takes place at the transfer points either from belt to belt, or from belt to inclined chute ore belt to ore pile. Usually, two or three mixing bars at each transfer point are also included to help the mixing action. Plows to move the ore around on a moving belt are also used.

Jan 11, 1984

By J M. Totterdell

The Permian-Triassic Bowen Basin and the Jurassic-Cretaceous Surat Basin evolved in a backarc tectonic setting behind an active convergent plate margin in eastern Gondwana. Several extensional (Early Permian; Eocene) and contractional (mid-Permian; Early Triassic; Middle-Late Triassic; early Late Cretaceous) intraplate deformational events are recognised in the basins. These can be correlated with similar events in the New England Orogen that was being deformed in the Late Permian-Late Triassic as a foreland thrust belt. The intraplate deformations were probably the consequence of plate interactions, including the accretion of terranes, at the ancient active plate margin, remnants of which now occur in New Zealand.

Jan 1, 1995

Factual data about the sedimentation in the Newcastle Coal Measures are presented. Data concerning the total coal measure sequence (isopachs, sand/shale ratio, and total coal thickness variation), data about three coal seams (Borehole, Dudley, and Victoria Tunnel) and data about interseam conglomerate units are discussed.From this data conclusions are drawn about the coal measure environment. The western edge of the coal basin, the Lochinvar Dome, although a high feature, was apparently stable during coal measure time. Despite its height it apparently supplied little sediment to the basin.The northern and north-eastern edge, which was unstable, supplied most of the coarse detritus (including the conglomerates) to the basin. The conglomerates show patterns of fluvial origin but after a period of "normal" variations in pattern they become restricted to two parallel zones evidently tectonically controlled. Deposition of conglomerates is episodic and separated by periods of coal formation when deformation was apparently slight. Formation of each of the three seams considered followed a rather similar pattern- each show development of thick coal around the basin edge and poor thin coal in the "axial" region of the present synclinal structure.Evidence of ill situ formation of some areas of the seams is discussed and periodic deformation of the basin during coal measure time is postulated.The unusual character of this coal basin, in particular the very coarse units, is stressed, despite the presence of many "normal "coal basin features.

Jan 1, 1970

By R. R. Sayers

VENTILATION may be defined as the process by which vitiated air of an inclosed or partly inclosed space is continuously replaced by fresh air. Fresh air has been defined as invigorating pure air. Pure dry air at sea level contains the following gases:1 Analysis of Air at Sea Level PER CENT. Oxygen 20.94 Nitrogen 78.09 Carbon dioxide 0.03 Argon 0.94 Helium, krypton, neon, xenon, hydrogen, hydrogen peroxid, ammonia, ozone traces CARBON DIOXIDE LIMIT For many years carbon dioxide was used as an index of the purity of the air vitiated by the metabolism of people. It was, however, well known that the untoward effects produced on those exposed to such air was not due to the concentration of the carbon dioxide. It has been found that the untoward effects on the comfort and efficiency of those so exposed are due to the increased temperature and humidity. It has been found that men can breathe air containing many times the amount of carbon dioxide found in our worst ventilated theaters and assembly halls, which, according to Rosenau, do not contain above 0.5 per cent. carbon dioxide.

Jan 7, 1926

By R. R. Sayers

VENTILATION may be defined as the process by which vitiated air of an inclosed or partly inclosed space is continuously replaced by fresh air. Fresh air has been defined as invigorating pure air. Pure dry air at sea level contains the following gases:1 Analysis of Air at Sea Level PER CENT. Oxygen 20.94 Nitrogen 78.09 Carbon dioxide 0.03 Argon 0.94 Helium, krypton, neon, xenon, hydrogen, hydrogen peroxid, ammonia, ozone traces CARBON DIOXIDE LIMIT For many years carbon dioxide was used as an index of the purity of the air vitiated by the metabolism of people. It was, however, well known that the untoward effects produced on those exposed to such air was not due to the concentration of the carbon dioxide. It has been found that the untoward effects on the comfort and efficiency of those so exposed are due to the increased temperature and humidity. It has been found that men can breathe air containing many times the amount of carbon dioxide found in our worst ventilated theaters and assembly halls, which, according to Rosenau, do not contain above 0.5 per cent. carbon dioxide.

Jan 7, 1926

Provide the mining industry with a wireless surveying system for increasing efficiency in the drilling of methane drainage or exploration boreholes. Approach The Bureau of Mines has pioneered the technique of methane control by drilling long, horizontal drainage holes from within the mine complex. It was recognized during the early drainage projects that a major portion of the drilling operation was dedicated to hole surveying. In some cases more time was actually being spent on the surveying operation than on drilling. The large amount of time required for hole surveying was the result of having to pump an instrument to the bottom of the hole, then retrieve it with an attached wire line. Naturally as hole depth increased, so did the amount of time needed to perform the survey operation. If the survey operation could be improved it was obvious that overall efficiency in drilling of long, horizontal methane drainage holes would be greatly increased. The Bureau of Mines, therefore, developed, fabricated and tested in an operating coal mine a permissible wireless survey system specifically designed for small diameter methane drainage drilling. The prototype survey system was completed in 1982 and was given the IR-100 Award by Industrial Research and Development Magazine. A second generation survey system is currently being constructed using updated state-of-the-art electronic technology. The second generation system will be more portable, more reliable, easier to maintain, and less costly.

Jan 1, 1984

By Sabert Oglesby, Albert L. Thomas

Until recently, probably the best means of sampling airborne dusts has been the impinger method. Dust-laden air is drawn into a sampling tube, and the particulate matters separated from the air and collected in the liquid in the impinger. A sample of the suspension is prepared on a slide and counted through a projection microscope. This method is simple and reliable, but it does suffer drawbacks. Since the collected particles must be counted visually, results of the dust count are taken. This seriously impedes studying the effectiveness of dust inhibitors, such as water sprays, or making adjustments in equipment. Greatest disadvantage of all, however, is the tedious task of counting particles in the sample. With the growing desirability of taking more samples, the effort involved in making these counts is a real factor in the cost of dust control. Finally, it is generally recognized that impinger dust counts can be related to health hazard only for specific kinds of dust and under similar conditions. This is because the rather complex mechanism of dust damage depends so much on size distribution of the dust. Counts determined by impinger samples cover a limited size range that does not necessarily correlate with retention by the lungs and upper respiratory tract.

Jan 3, 1959

By Rolf R. von Oppenfeld

Onsite hazardous waste processors often find obtaining a Treatment Storage and Disposal (TSD) permit one of their first major challenges. Some processors may spend the time and money required by the permitting process, only to find out later that a permit was not necessary. This paper will present and analyze four strategies that processors may use to avoid obtaining a TSD permit. Some facilities will be able to remove their waste streams from RCRA's oversight by ensuring the material is not "hazardous" waste. Parties that treat waste while it is in process may be able to avoid generating "waste" altogether. Certain treatment facilities have been specifically exempted by EPA. Finally, treatment of waste while it is in generator storage tanks may be allowed without a RCRA TSD permit. Hazardous waste point of generation, an important determination relating to these strategies, will also be discussed. Generators and processors will find this paper useful when evaluating their permit exemption potential

Jan 1, 1996

By Luther J. Russell

Mineral development in South Dakota is aggressively encouraged by both state statute and county ordinances. Yet, an increasingly conservative philosophy is taking hold, resulting in expanded regulatory controls and concomitant increases in direct and indirect costs to permit and operate a mining operation. This paper examines the hidden costs associated with protracted permitting timeframes, land buy-outs, attorney's fees, etc., associated with the increasing emphasis for stiff controls on mineral development in South Dakota.

Jan 1, 1998

By Duncan Chalmers, Rob Nowell, Miguel Araos

Australian underground mines produce in excess of 60 mtpa of coal. Most of these use the longwall method, and they require the use permitted explosives (which are called “permissible” in other countries) for challenges that appear during the day-to-day activities. To obtain the approval for these explosives, they should pass Testing Memorandum #2 (TM-2), which sets out the test required for each category of permitted explosive. These categories are P1, P3, and P5. With P5 being unrestricted use and P3 and P1 have conditional use in underground mines. The TM-2 test was originally set up for NG-based permitted products around 1900. With the closing of NG plants around the world, ammonium nitrate explosives were the natural replacement, and therefore these explosives need to pass the TM2. Australia does have a P1-emulsion based explosive available. For high-risk scenarios (like blasting coal), no P5 explosives are available. The lack of P5 explosives has been prolonged for more than 25 years, since the phasing out of nitroglycerine-based permitted explosive products around the world. The main problem has been that when emulsion based permitted products are tested in the deflagration cannon, the results obtained were not considered in the TM2 criteria and therefore the tests were invalid. A research work on permitted explosives began in 2005 funded by the Australian Coal Association Research Program (ACARP). The aim of the project was to address the lack of P5-type permitted explosive (and, potentially develop them further, i.e., develop safer explosives) and understand the behaviour of emulsion explosive and the results they presented in the tests. Both bureaucratic and technical barriers appeared along the way. On the bureaucracy side, the facility was shut down, reopened, and shut down again. In view of these difficulties, assistance was sought overseas. On the technical side, from the very start the results of the tests when using emulsion-based permitted explosives were not established in the criteria, ignitions occurred for trial samples that were expected to be P5-type, etc. The aim of this document is to present the painful journey in the Australian industry to have a P5-type emulsion-based permitted explosive, for use in UG coal. Also, the technical learning acquired about emulsion explosives and the ignition path of mixtures methane / air will be shown.

Jan 21, 2025

By R. E. Nelson

The Alton Coal project, located in south-central Utah, lies at one point just over six miles from Bryce Canyon National Park. This region of the southwestern United States has been called the "Golden Circle" of national parks and monuments. Can a mine be inserted into this region so that it does not intrude on this spectacular landscape? The Alton Coal Project is a proposed surface coal mine designed to serve as the fuel source for the Harry Allen Power Plant, a 1,000 megawatt generating station planned for a site 25 miles northeast of Las Vegas, Nevada. The mine and the power plant will be connected by an underground pipeline through which coal will be transported in slurry form.

Jan 1, 1988

By Jonathan M. Pachter

Introduction The Bailey mining complex is located in Greene County, PA, in the Talley Run valley. It includes two Pittsburgh No. 8 seam deep mines (Bailey and Bailey No. 2), a coal preparation plant, and two refuse areas. Clean coal is shipped from the complex by way of a 24-km (15-mile) rail spur. It con¬nects to the Monongahela Railroad in Waynesburg, PA. In early 1981, Consolidation Coal Co. (Consol) began a permitting effort aimed at building the mine. Construction began in Dec. 1981, less than six months after the first application submittal. Clean coal was produced by the Bailey preparation plant in Sept. 1984. Several factors allowed quick permitting at Bailey. Effective project planning, including early formulation of a project planning team, and identification of red flag issues helped. So did innovative responses to environmental questions, and development of environmentally sound project designs. Forming a project planning team Consol management decided that Bailey mine construction had to begin in late 1981. A project permitting team was immediately formed to see that this goal was achieved. Team members included a project manager and personnel from Consol's engineering, environmental, and operating departments. Communications among all team members was crucial in obtaining the various state and Federal environmental permits. All project permitting team members participated in weekly meetings during application preparation. Discussions at these meetings ranged from recent public contacts, to application content, to environmental design considerations. Establishing a project manager was critical to the team's success. The project manager was responsible for seeing that permit acquisition, facility construction, and operation of the mining complex proceeded on schedule. The project manager had the final word, mediated disagreements, and frequently served as project spokesman to the public. Identifying red flag issues Red flag issues are those environmental factors with the most potential for delaying the schedule or stopping the project. The first red flag issue identified was organized local opposition. This opposition had completely derailed a US Soil Conservation Service proposal to build a multipurpose dam on Enlow Fork, a short distance

Jan 9, 1985

By Miguel Gutiérrez

This paper will seek to provide an awareness of the challenges the permitting process presents to the engineering design for open pit mining projects in Perú. This awareness will create a better understanding of the permitting process within the several groups in mining companies that are responsible for getting the mine project started or continue its operations.

Sep 21, 2013

By R L. Grogan

Mining is currently undergoing a progressive expansion into novel environments (such as the deep ocean), commodities (such as tantalum, rare earths, and other ‘green economy minerals’), and new methods (such as the autonomous underwater cutting machines required to operate in the deep ocean environment, or the use of expanding grouts to deliver a blast-free mining method). The advent of novel mining, environments and commodities heralds an era that will undoubtedly start with much discomfort on the part of regulators and stakeholders, due to a feeling of overwhelming uncertainty. These proposed mining scenarios have few precedents, few examples of successful implementation, short baseline monitoring periods, and few examples of legacy sites that may assist with understanding long term risk and exposure. The evolution of the environmental and social impact assessment (ESIA) process in many regulatory environments recognises stakeholder engagement in a formal and facilitated manner. This is a positive step, and allows stakeholders to be much more meaningfully involved in the permitting process than they historically were. However, with this advance comes the challenge of identifying and communicating with stakeholders; sharing information in a meaningful way, fostering relationships with what can be an extremely large group, and delivering on commitments that inspire confidence to permit operations that have never been permitted before. In order to meet this challenge, it is suggested that changes to collection of data, communication of data, the nature of commitments, and the reporting of performance need to be made in order to effectively communicate management of new technologies, and the impacts that mining may have in new environments (such as the deep ocean). The communication challenge is necessarily greater when describing technology that has never been used, or environments that have never previously been accessed by humans on an industrial scale. CITATION:Grogan, R L, 2018. Permitting in the face of uncertainty – how to deliver confidence to regulators and investors, in Proceedings Life-of-Mine 2018, pp 46–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Adrian Coombs, Paul Magowan, Derek Zoldy

Continued development and intensification are fuelling the urgent need for new trunk infrastructure within The Regional Municipality of York and throughout the Greater Toronto Area. Permitting of these projects is increasingly subject to public scrutiny to severely restrict dewatering through construction technologies and the requirement for a comprehensive and effective Environmental Management Plan. Three current projects: one on the York Durham Sewage System and two in the City of Toronto 1.Conventional Design, Tender, Award: 4,150m (13,600 ft.) 2.7m (9 ft.) finished interior diameter soft ground tunnel for York Region’s YDSS Interceptor Trunk Sewer 2.Negotiated Contract: 3,800m (12,500 ft.) 3.5m diameter (11.5 ft.) rock tunnels for Enwave’s environmentally sustainable and innovative chilled water system in downtown Toronto 3.Conventional Design, Tender, Award: 2,200m (7,200 ft.) 3.3m diameter (10.8 ft.) rock tunnel for reinforcement of Hydro One’s primary hydro feed in the downtown core of Toronto These projects exemplify issues such as: EPB tunnel and sealed shaft technologies Substantial permitting requirements associated with dewatering Mitigation of rock creep Congested downtown rights-of-way Deep shafts and confined working compounds Unique scheduling and cost benefits when Owner, Contractor and Consultant can work together cooperatively.

Jan 1, 2007