Search Documents

By R. L. Garrett

The quality of mineral additives used in a drilling fluid (mud) can dramatically affect the fluid's properties and the overall cost of drilling an oil or gas well. The principally wed minerals are bentonite, barite, barite/hematite blends, and hematite alone. The high specific gravity minerals, barite and hematite, are used to increase drilling fluid density. Bentonite clay is used to increase drilling fluid viscosity and gel strength and to provide a low permeability filter cake. A multimillion dollar investment in a well and the safety of the personnel on the drilling rig can depend on how effectively these mud additives perform with other constituents in the mud. This paper points out effects caused by small amounts of certain carbonate and sulfide mineral impurities in barite or hematite and how polymeric extender additives in bentonites contribute to unpredictable behavior of a mud. Effects like these are the reason oil companies using these materials sometimes set their own quality standards beyond those already specified in APZ Spec. 13A. Also discussed in this paper are the current standardization activities of API Committee 13 on these minerals.

Jan 1, 1988

By R. L. Garrett

The quality of mineral additives used 1n a drilling fluid (mud) can dramatically affect the fluid's properties and the overall cost of drilling an oil or gas well. The principally used minerals are bentonite, barite, barite/hematite blends and hematite alone. The high specific gravity minerals, barite and hematite, are used to increase drilling fluid density. Bentonite clay is used to increase drilling fluid viscosity, gel strength and to provide a low permeability filter cake. A multi-million dollar investment in a well and the safety of the personnel on the drilling rig can depend on how effectively these mud additives perform with other constituents in the mud. This paper points out effects caused by small amounts of certain carbonate and sulfide mineral impurities in barite or hematite and how polymeric extender additives in bentonites contribute to unpredictable behavior of a mud. Effects like these are the reason why oil companies who use these materials sometimes set their own quality standards beyond those already specified in API Spec. 13A. Also discussed in this paper are the current standardization activities in API Committee 13 on these minerals.

Jan 1, 1986

By D. Leppert

Mr. Garrett brings up several interesting points with respect to the proposed API specification for "nontreated bentonite." However, although not explicitly stated, these specifications are being written based strictly on bentonites from the Wyoming/South Dakota area. Other sodium bentonites may be suitable for use as drill mud but will be unacceptable since the specifications are designed for Wyoming bentonites. Regardless of the API's intent that its specifications are intended only as guidelines, they are generally adhered to on an international basis and, for practical purposes, might as well be chiseled in stone. Estes (1986) notes that the quality of bentonite available from Wyoming producers has steadily declined since the early 1960's. The plastic viscosity: yield point (PV:YP) ratio was included in the current API 13A specification primarily to prevent excessive polymer treatment of lower quality bentonite to make drill mud. However, with development of polymers designed to control YP, this specification cannot ensure that only high-quality bentonites are used for drill mud. Nor will the new specifications for untreated bentonites. Other sodium bentonites are available. Bentonite produced in southeast Oregon demonstrates superior performance characteristics without addition of polymer or other chemicals. However, the exceptionally high purity of these deposits leads to a relatively high YP:PV ratio since the naturally high YP probably results from the higher purity and smaller particle size of this bentonite (Rath. 1986 and personal communication). These bentonite; typically have a smectite component exceeding 90% (Rath, 1985), compared with 70% to 75% smectite for typical Wyoming bentonites, as determined by X- ray diffraction and tests for colloid content. As evident from the accompanying table, the untreated Oregon bentonite has excellent rheological properties, though different from Wyoming bentonites due to the high purity. Additionally, this bentonite reacts well with polymers typically used in the oil industry, making it eminently suitable for use in a low-solids mud system. The extremely low grit content, less that 0.5% on a 75 mm (200-mesh) wet sieve, greatly exceeds the standards set for Wyoming bentonite. Optimum rheological properties are obtained at a higher moisture content than Wyoming bentonites. At 10% moisture, API 13A maximum, the clay is overdried, again reflecting the high smectite content. In summary, the specifications proposed by the API Task Group will ensure that only Wyoming producers can supply "nontreated bentonite to the oilfield since specifications are

Jan 1, 1990

By V Rasouli, G Cavanough, A Mokaramian

The sampling time, the costs and its quality are the three factors that determine the best method of drilling in mineral exploration. The two principal methods of reverse circulation (RC) and diamond core drilling are often used in combination by mine operators. RC is used for drilling shallow holes and in-pit grade control, and core drilling for deeper holes to identify future resources. The RC method is faster and more flexible than coring and provides virtually uncontaminated cuttings (ranges from dust to 25 mm chips) to the surface cyclone suitable for geochemical anomalies. The diamond coring produces core samples to increase the level of geological knowledge and the 3D extension and distribution of the orebody. However, both of these methods are subjected to certain limitations and inefficiencies in reaching deeper depths and drilling complex hole geometries. Examples of such shortcomings include the inability to provide enough air pressure for RC drilling and high friction between drill pipe and the hole wall in diamond core drilling.Considering that delivering large volume of reliable samples from deep zones to the surface in shortest possible time is of paramount importance in mineral exploration, and assuming that obtaining core samples over whole overburden is not always essential, then drilling small size holes as fast as possible and delivering the small chip samples to the surface would be a good alternative with several advantages over conventional drilling methods for deep hard rocks mineral exploration. As a result, the use of coiled tube (CT) drilling technology has been proposed recently for such applications. CT is a continuous length of ductile steel or composite tube stored and transported on a large reel; and allows fast drilling by eliminating the connection time and providing continuous circulation during drilling. This enables quick access to the zone of interest to collect the cuttings or obtain core samples. CT is advantageous particularly in drilling directional boreholes and multi-laterals. In this paper, feasibility of using CT delivering reliable samples is discussed for deep mineral exploration. In addition, recent developments and practices are presented that make CT a reliable drilling technology to drill cheaper, faster and deeper and to deliver more continuous and reliable data and samples from deep formations.CITATION:Mokaramian, A, Rasouli, V and Cavanough, G, 2012. Quality sampling using coiled tubing drilling in deep mineral exploration, in Proceedings Sampling 2012 , pp 73-80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By Wilfrid Comeau

This paper deals with the concept of a Quality-Assurance Manual, to the ISO-9001 Level, for quarry blasting in the urban environment. A case history of the incident, which led to its development, is presented in addition to three other case histories. These case histories are related to the potential effectiveness of a well thought-out and applied Quality-Assurance Manual in the conclusions. The basic principle, behind the development of a Q-A manual, is to supply a maximum of quality assurance with a minimum of disturbance to the operation of the quarry. This requires that every intervener in the quarry blasting operations, from management to labourer, be made responsible for the quality of their work. This basic goal can be achieved with a minimum of paper work and added bureaucracy. The manual respects the ISO principle that: Q-A Manuals are not recipe books and should allow for continuing technological developments.

Jan 1, 2003

By D Craw, J Pope

The Greenland Group, Westland, can be characterised with respect to environmental issues by the application of a GIS database (DAME), and specific sampling campaigns. Waters draining gold mineralised areas have a distinctive chemistry characterised by neutral pH and arsenic as a trace element. The acid neutralising capacity (ANC) from carbonates usually exceeds the maximum potential acidity (MPA) from sulphides resulting in circum-neutral pH. These waters are readily distinguishable from waters draining coal mine related areas, which commonly have low pH (~4) and low As concentrations (~0.1 ppm). In contrast, dissolved arsenic mobilised from Greenland Group historic gold mining areas is up to 2.4 ppm. This As mobilisation is controlled by the secondary As mineral, scorodite (FeAsO2+2H2O). Maximum dissolved As concentrations increase with increasing pH, corresponding to the increasing solubility of scorodite with increasing pH. Dissolved As is attenuated by dilution, precipitation of scorodite, and/or adsorption to iron oxyhydroxide (HFO). Adsorption to HFO is an important attenuation mechanism in and adjacent to many mine sites. HFO is abundant at mine sites where pyrite was abundant in fresh rock, such as where the mineralised zone is dominated by disseminated pyrite. Pyrite, and resulting HFO, are relatively rare where mineralisation occurred as well-defined quartz veins. Localised HFO occurs also where ankerite oxidises in host rocks. Arsenic output flux (ca. 25 g/day) from historic gold mine sites is commonly less than the natural background flux from mineralised rocks (>5000 g/day).

Jan 1, 2006

By Fazel G. Jahromi, Ahmad Ghahreman

"Atmospheric leaching of arsenical sulfide concentrates, and especially enargite leaching, is one of the major challenges within the current hydrometallurgy research area. One of the recent processes developed for sulfide ore treatment is atmospheric leaching in the presence of AF 5, a novel carbon based catalyst, in chloride media. The quantification of different ion concentrations during enargite and chalcopyrite leaching in the presence of AF 5 were measured and the copper recovery rates of 97% and 96% were achieved. The objective of this study is to shed light on the leaching mechanism of the sulfide minerals. Based on the speciation of iron and copper by different titration methods, the AF 5 catalyst first reduced ferric and cupric ions and then oxidized ferrous, cuprous and arsenite ions. The oxidation behavior of the catalyst enhanced the leaching results. The AF 5 catalyst also caused in situ precipitation of scorodite in leaching experiment. The speciation of ions in the chloride media were simulated by Phreeqc software and the dominant species in the leaching solution were determined.INTRODUCTION The hydrometallurgy of copper has been used for several decades and is still under development for more complex copper sulfide minerals due to their refractory nature. Most of the world copper reserves are in the form of chalcopyrite; and enargite is known as a major contaminant. Pyrometallurgical processing of enargite is problematic due to arsenic release and tight environmental regulations (Peacey, Gupta, and Ford n.d.). On the other hand, lower recoveries in the hydrometallurgical processes make most of these processes impractical. Several leaching processes have been developed for the leaching of copper sulfide minerals. Some of the common treatment methods for copper sulfide minerals are pressure oxidation leaching (POX), CESL, Activox, Albion process, atmospheric ferric sulfate leaching, Dynatec, Galvanox, and Hydro copper process (Barr, Defreyne, and Mayhew 2005; Conner and Anderson 2013; D.G. Dixon, Mayne, and Baxter 2008; Hyvärinen and Hämäläinen 2005; Palmer and Johnson 2005; Rohner, Bartsch, and Ngoviky 2012). Generally it is not viable to dissolve copper sulfide minerals at ambient pressure in mild acidic media and dissolution of these refractory minerals requires harsh conditions in the presence of oxidant materials (Biswas and Davenport 2002). Ferric ions have been used as an oxidant in different media in copper sulfide leaching processes. U. S. Bureau of Mines’ Reno Metallurgy Research Center in 1969 (Haver and Wong 1971) investigated ferric chloride leaching of chalcopyrite. Dutrizac and Macdonald (1972) studied ferric sulfate leaching of enargite. Based on this study, 50% of the copper was recovered at 80-85 ºC after 7 days of leaching. Cupric ions can also be used as an oxidant. Parker, Paul, and Power (1981) stated that cupric/cuprous couples are more effective than ferric/ferrous couples in chloride media because they are rapid and reversible. The Hydro Copper process leaches copper sulfide minerals in chloride solution catalyzed by cupric ions. In this process, copper dissolves as cuprous ions in presence of cupric ions (about 10 g/L) (Hyvärinen and Hämäläinen 2005)."

Jan 1, 2017

By C D. Pocock

Maintaining catch berm capacity in open pit mines through controlled blasting prevents production delays associated with managing risks associated with wall instability. A method has been developed to quantify the drill hole deviation of presplit holes at Century Mine. Different controlled blasting techniques are used to control wall quality and decrease the risk. The performance of presplit drilling, in terms of deviation from design has been investigated. A methodology has been developed to quantify the drill hole deviation in three dimensions. This methodology was converted into a series of algorithms capable of handling an extensive range of data. The methodology was applied to a case study at Century Mine to evaluate the performance of drilling on two presplit blasts. Overall, 67 drill holes were investigated in the case study. The drill hole deviation was quantified in terms of three parameters: skewness, linearity and drill hole deviation parameter. Methods for quantifying each parameter were developed. Skewness, a measure of the amount of curvature and linearity, was defined as the measure of the consistency of the gradient of the drill hole. Drill hole deviation parameter is defined as the average measured deviation of the surveyed drill hole position from the design position. Acceptable drill hole deviation tolerances for each of the defined parameters were developed by analysing drill hole deviation parameters with respect to implications to catch berm capacity. Verification of the methodology was confirmed through the comparing of the completed drill hole deviation results using both visual inspection and cross analysis for each of the three methods. Holes with an R squared value of less than 0.97 for skewed deviation were classified as having skewed deviation, while holes with a difference in gradient of 3.5 were classified as having linear deviation. The results show that 76 per cent of the drill holes had deviation. Of this, 19 per cent were skewed, 57 per cent had linearity and 12 per cent contained both skewed and linearity deviation.

Nov 8, 2011

By Yinan Zhang, Yi Luo

The widely used R70 method is modified to measure the self-heating propensity of low-rank coals. This modified R70 method enables the introduction of controlled amount of moist oxygen into the reaction vessel. Three coal lumps were collected from three different locations in a surface mine in the Powder River Basin. The coal samples were tested in oxygen flow with controlled moisture content under adiabatic condition. By measuring the relative humidity at the exhaust exit point of the testing setup, the flux and cumulative wetting heat that is consumed by coal samples can be determined. Through a better way of determining the coal’s specific heat, the total heat, including heat of wetting and coal’s oxidation heat, required to raise coal to a given temperature can be determined. Then, the contribution of heat of wetting at the different stages of the testing is quantified. The effects of evaporative heat through a group of tests have also been quantified. From this research, a better understanding of the effect of wetting heat on inducing low-rank coal’s spontaneous combustion can be acquired.

Nov 30, 2022

By H Lieberwirth, M Pfeifer, F Heinicke

HPGRs (high pressure grinding rolls) have been developed within the last decades for energy efficient processing of a wide variety of ores. Special interest has been raised by projects increasing the capacities of processing plants by installing HPGRs prior to ball mills. Bond ball mill tests have been used for decades as a base for ball mill dimensioning in mineral circuits. For final CAPEXOPEX considerations of the processing circuit, one key question is about the level of grinding energy split between HPGR and downstream grinding stages. This is especially interesting if the downstream process comprises multiple grinding stages combined with separation steps. The paper presents investigations on grinding energy consumption, size distribution and microfracturing of HPGR products, which affect the efficiency of the whole comminution and sorting process.

Aug 24, 2022

By I. P. Swainson, A. Ilbagi, H. Henein

Powders of Al-50wt%Ni, Al-40wt%Ni and Al-36wt%Ni were produced using the Impulse Atomization technique, a rapid solidification technique. The molten droplets were cooled in-flight by the stagnant helium or nitrogen in the atomizing chamber. The resulting powders were sieved into different size ranges. X-Ray diffraction and neutron diffraction were used in order to quantify the phase fractions in the samples. The computer software GSAS was used to calculate the weight fraction of the existing phases, namely Al3Ni2, Al3Ni and Al, by profile refinement method. The effect of processing parameters, alloy composition and particle size will be discussed in this paper. In brief, no AlNi was found in any of the samples analyzed. Higher cooling rates resulted in the reduction of the ratio of Al3Ni/Al3Ni2. Also, at high cooling rates, Scheil closely predicted the ratio of Al3Ni/Al3Ni2. Some metastable phases were found in Al- 36wt%Ni.

Jan 1, 2010

By M E. Malmstr÷m

Quantification of site-specific sulfide oxidation rates is crucial to accuracy of prediction of, for example, the environmental impact of a mine site. Sulfide oxidation reactions are reportedly increased by bacterial mediation; determination of abiotic and biotic weathering rates thus requires the establishment of sterile control samples. However, sterilisation often involves exposure of samples to extreme conditions that may alter the physical, chemical, or mineralogical characteristics of the tailings and hence affect element release rates. The impact of various sterilisation techniques, common and novel, on the element release rates from tailings from the Kristineberg site, northern Sweden, has been investigated. Batch weathering experiments indicated that the different methods of sterilisation (autoclaving, heat treatment, ethanol/heat treatment, application of antibiotics, rinsing with distilled water, and γ-radiation) did not greatly affect long-term element release rates. Long-term experiments (>30 days) are thus to be recommended for establishment of weathering rates. Sterilised and untreated control samples showed similar element release rates after ~100 days of experiments; possible explanations include that microbial oxidation is not important under our experimental conditions (Po2 = 0.2 atm, pH ~2.3, 22¦C, 0.01 M HNO3, no additional nutrients).

Jan 1, 2003

By Larry Hopkins

The molten metal circulation pump has become a staple for melting aluminum in reverberatory furnaces. The forced convection that is created in the melt efficiently provides circulation while dramatically improving melt rates, lowering fuel consumption, extending refractory life, and providing metallurgical homogeneity. Two metallurgical guidelines that are important to many casthouses are molten metal inclusion levels and hydrogen gas content. In order to improve molten metal quality, furnace and casting practices must 'manage these molten metal defects, Today specialized in-line degassing and filtration equipment is used downstream of the furnace to accomplish these tasks. In contrast, the molten metal gas injection pump has metallurgical contact time in the process for hours during the charging/homogenization cycle. The qualitative benefits of employing a gas injection pump to "pre-clean" are outlined and discussed against historical empirical information obtained with alternate methods. Further, a recent study quantifies the merits of this gas injection technique as an effective molten metal quality improvement tool. Specifically, the effects on inclusion level as determined by PoDFA?, gas content as determined by A1SCAN? sampling and alkali metal content as determined by spectrographic analysis are examined in relationship to various gas feed compositions and flow rates.

Jan 1, 1995

By J. Lu, D. G. Ivey, H. Henein

Microalloyed steels are widely used in the oil and gas industry. They are a class of high strength, low carbon steels containing small additions of niobium (Nb), titanium (Ti), molybdenum (Mo) and/or vanadium (V). These steels have good strength, toughness and excellent weldability, which are attributed in part to the presence of nano-sized carbides, nitrides and carbonitrides. In the pursuit of developing higher strength microalloyed steels, it is of great interest to quantify the size, distribution, volume fraction and chemical speciation of these precipitates. However, characterization techniques suitable for quantifying fine precipitates are limited. Possible characterization techniques include SEM, TEM and matrix dissolution. A comparison is presented of the various techniques.

Jan 1, 2005

By G Chitombo, D Francis, P C. Stewart, I Brunton

The ability to precondition (weaken) a rock mass to enhance caving (cavability and fragmentation) is becoming increasingly important, as more potential caving deposits are in stronger rock masses, and at greater depth. This paper discusses a full-scale blast preconditioning experiment conducted at the Cadia East mining operation, including quantification of visible and microscale blast damage. From a cave mining perspective, the objectives of the experiment were to quantify the effect of confined blasting on rock mass characteristics relevant to enhanced caving, and to provide calibration data for the purpose of numerically modelling alternative blast preconditioning designs.The experiment was located approximately 360 m below surface, and consisted of two f165 mm blastholes (60 m vertical holes) and eight HQ diamond drill monitoring holes (35 m horizontal holes). The diamond drill holes were used to sample the rock mass before and after the blast at varying distances from the blastholes. Rock mass blast damage was quantified both visually using core logging, and on a microscale using LABYRINTH® statistical analysis of X-ray microtomography data. Results from the experiment indicated four major findings:on the visible scale, the experiment indicated a 147 per cent increase in the number of hairline cracks within 5 m (p value = 0.015), but no change in geotechnical logging parametersmicroscale tomography of intact rock samples indicate significant localised intact rock damage up to 4 m from the blasthole (p = 0.007)preliminary point load test results indicate that blast damage results in a significant reduction in intact rock strength (p = 0.050)the significant increase in porosity and microfracture size associated with damage provides a mechanism for reduced intact rock strength due to confined blasting.CITATION:Stewart, P C, Brunton, I, Francis, D and Chitombo, G, 2016. Quantification of rock mass damage associated with a confined blast preconditioning experiment at the Cadia East block cave, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 119–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M. S. Seehra, V. S. Babu

"INTRODUCTION The accurate determination of the free silica index in coal mine dusts is an important requirement because severe health hazards are believed to be associated with the inhalation of respirable-sized silica particles.1-6 Free silica refers to the three polymorphs of silica (Si02)viz., quartz, cristobalite, and tridymite-although quartz is usually the dominant form in most mine dusts.6 The free silica index is the concentration in micrograms of free silica in air per m3 of air sampled corrected to standard conditions of 25°C and 760 mm/Hg, the present MSHA (Mine Safety and Health Administration) limit on time-averaged basis being 100 µ.g/m 3 for coal mines. A recent review7 has concluded that quartz, cristobalite, and tridymite particles impart nearly equal long-term hemolytic damage when compared on a per unit surface area basis.At present, two experimental methods-viz., transmission infrared spectroscopy (TIRS) and x-ray diffraction (XRD)-are commonly used for the determination of silica concentrations in mine dusts. In TIRS, which has been adopted by MSHA and is commonly called the P7 method, the silica absorption band near 800 cm - 1 is used for quantification. However the mineral kaolinite, which is commonly present in mine dusts, also has absorption band, albeit weaker, at 800 cm- 1• To correct for this interference, one uses the stronger 915-cm -1 band of kaolinite to determine the concentration of kaolinite, and the kaolinite contribution to the absorbance at 800 cm-1 is then determined from a calibration curve, leading to the determination of silica by subtraction. In the XRD technique, usually an internal standard such as CaF 2 is used to determine the concentration of silica from line intensity measurements. XRD has the added advantage that concentrations of quartz, cristobalite, and tridymite can be determined.8•9 In an exhaustive study on the precision of the techniques ofTIRS and XRD for monitoring worker exposure,9 the conclusion has been reached that both methods measure silica within 253 of the ""true"" value 953 of the time in a single laboratory."

Nov 1, 1995

By J. M. D. Wilson

An analytical program using a combination of SEM-based image analysis techniques is developed for automated modal analysis of ores containing silicate and other gangue minerals. Previous knowledge, gathered by means of either optical microscopy, X-ray diffraction, SEM, or electron microprobe analysis is used to establish discrimination criteria in the image analysis program. The program initially discriminates minerals on the basis of their relative grey values in a backscattered electron image. For those minerals which have overlapping grey levels the minerals are identified by the program using energy dispersive X-ray spectrometry with X-ray counting for twelve or more elements. This technique is useful to quantify ores in which the gangue minerals are numerous. Two cases of application are presented.

Jan 1, 1999

By J. A. L. Napier

This paper presents an overview of work carried out by the CSIR Division of Mining Technology and formerly by the Chamber of Mines Research Organization (COMRO) to quantify the behaviour of the stope fracture zone near deep level goldmine stopes. The motivation for this work is first reviewed in the context of the unsatisfactory status of current mine layout design criteria. Numerical methods to represent failure processes are reviewed briefly. Specific studies of microfracture processes are described as well as physical modelling experiments that can yield insights into deformation mechanisms. Modelling of stope scale deformation mechanisms are presented and considerations relating to elastodynamic modelling of the rock mass are described. The implications of this understanding in relation to prospects for active fracture zone ?engineering? are outlined and finally, the directions of future research work are proposed.

Jan 1, 1997

By J Rutter, D Francois-Bongarcon, M Federov, N Odiar, M Scott

There are two fundamental methods for metalliferous sensing of primary crushed ore available for deployment at operations. These methods can be classed as surface measurement techniques (including XRF, LIBS, NIR, SWIR) or penetrative/semi-penetrative measurement techniques (including PGNAA, PFTNA, GAA, MR). While the individual sensing technologies exploit different physical phenomena to measure metal content, penetrative sensor measurements of grade are often regarded to be superior to surface measurement techniques due to the much larger sampling volume penetrative techniques provide. Surface sensing techniques often utilise simpler, established technologies that have considerable benefits in the speed of analysis, capital costs, ease of deployment, social license to operate and operational safety. This paper investigates whether surface sensing techniques achieve adequate sampling representativity of primary crushed rock mass to provide economic benefit over penetrative sensing technologies for bulk ore sorting applications. The paper details the methodology used to assess whether surface XRF measurements change throughout various stages of comminution, and increased surface exposure, from primary crushed ore (top size of -175mm) to finely crushed product for assay (top size -2mm). The methodology was applied to 2 ore mineralisation styles, across variable metals and grades, to identify any associated opportunities and limitations to surface sensing techniques. The results assist in developing a method to determine if surface sensing and measuring via XRF is an adequate representation of the rock mass for bulk ore sorting applications and identify any associated limitations in particle size distribution, mineralisation or natural deportment strength to guide suitable application of surface sensing techniques.

Nov 10, 2020

By Angus Maxwell, Jacob Grasmick

As the tunneling industry continues to adopt Tunnel 4.0, digital twins of the tunnel construction site are becoming standard requirements for tunneling projects. However, the benefits of these remain unproven to many practitioners. The paper discusses the various implementations of digitalization and describes efforts to combine all data types to analyze the relationships between influences, predictions and performance in a single digital platform. This includes data pertaining to investigations, design, construction, monitoring and post-construction asset performance and management. Based on 16 years of global tunneling projects the paper aims to quantify the tangible and intangible benefits of such systems. Using a number of real examples, the paper describes where opportunities were taken and where they went unrealized. Challenges and considerations for both procuring and developing these digital twins are also discussed.

Jun 13, 2021