Search Documents

By B. Tiryaki, M. Ayhan, O. Z. Hekimoglu

Coal shearers are one of the major sources of dust and fines in underground coal mines. Despite considerable research investigations, no comprehensive in situ investigations coupled with extensive laboratory studies on the effects of drum design on generation of dust and fines have been found. It may be for this reason that many major shearer drum manufacturers persistently employ a certain drum-lacing pattern on current coal shearers, which is believed to cause excessive dust and fines in coal mines. This paper shows how respirable dust and fines are minimized under near-identical conditions when the drum lacing pattern was changed from a triple-tracking to a single tracking arrangement. A series of laboratory trials simulating in full scale the practical cutting action of tools was followed by extensive long-term underground trials during production operations in OAL (Cayirhan) Lignite mine in Turkey. The results are presented and discussed, and recommendations for proper drum-lacing in terms of respirable dust and fines are made.

Jan 1, 2002

By Jared Onyirimba, Jim Viellenave, Hal Demuth, Dale Verran, Chad Sorba, Errol Lawrence, David Bronkhorst

As outlined within the Denison Mines Corp’s (“Denison”) Pre-Feasibility Study ("PFS") completed in late 2018, additional work is required to increase confidence and reduce risk associated with the application of the In-Situ Recovery (“ISR”) mining method at the Phoenix deposit, located on the Wheeler River Uranium Project (“Wheeler River” or the “Project”) in northern Saskatchewan. The successful application of ISR in any geological environment largely hinges on three fundamental requirements, 1) permeability (of the deposit), 2) containment (of the mining solution) and 3) leachability (of the mineralization). Denison has designed several staged technical programs to progressively reduce risk associated with these requirements as the Company advances the Project toward a Feasibility Study (“FS”) and Environmental Impact Assessment (“EIA”). This paper will discuss the scope and results of certain technical programs being undertaken as the Company aims to develop the first ISR mining operation in the Athabasca Basin.

Jan 1, 2020

By Blair Hrabi

Introduction; ?Risks Associated with the Resource Estimation Process; ?Limitations of Available Data; ?Geological and Structural Control of Mineralization Trends; ?Recognizing Multiple Mineralization Controls and Complex Trends; ?Accurate Geodomaining; ?Conclusions.

May 1, 2013

By Fair A, Oxenford J

Syncrude Canada Ltd operates one of the largest open pit mines in the world at Fort McMurray in northern Alberta, Canada. In 1993, Syncrude mined and processed 131.2 Mt of oil sands to produce 67.0 MBbls of synthetic crude oil (SCO). This represents approximately 13 per cent of Canada's crude oil requirements. In addition to the oil sand mined, Syncrude moved approximately 96 Mt of overburden ahead of the mining operation in 1993. Since start-up in 1978, Syncrude has had outstanding success in improving the safety and reliability of its operation. Much of this success has been achieved by reducing risk through the application of new and improved technology. This improved safety and reliability has resulted in, among other things, very significant improvements in operating costs and profitability. This paper discusses some of the technology applications that have been introduced at Syncrude to reduce risks to people, equipment, operations and the environment. Three specific examples will be discussed in detail to demonstrate how reductions in risk have greatly improved the operation.

Jan 1, 1994

By Reed Thorne

To many people, rescue from elevated, sometimes vertical, locations brings about thoughts of heroism mixed with brawn and self-sacrifice. Images are conjured of cliff rescues where the technical effort is hanging from a few seemingly small nylon ropes hundreds of feet above the ground. Such is the vertical realm of technical rope rescue. This is a technical field in which the author serves professionally as battalion chief of (rope) operations for a northern Arizona fire district, and as a private sector instructor to mines in the United States and Canada.

Jan 1, 1996

By Kim M. Cornelius

Musculoskeletal injury is a term used to describe a wide range of soft tissue disorders which affect the nerves, tendons, and muscles. Common examples include lower back pain, tendonitis, and carpal tunnel syndrome. The majority of these injuries are not the result of sudden mishaps, but usually develop gradually from repeated wear and tear. Symptoms may first appear after weeks, months, or even years. Symptoms may result from many types of activities, performed at work or at home, and it is often difficult to attribute a single event. In fact, it is more common to identify the factors which may have contributed to the development of the condition. The terms repetitive strain injuries or cumulative trauma disorders (CTDs) have been commonly used to refer to disorders that have occurred due to work related activities (Putz-Anderson, 1988; Fraser, 1989). Three main risk factors contribute to CTDs: force, repetition, and awkward postures. Any one or combination of these may contribute to the development of CTDs. Therefore, the design of equipment in conjunction with the required tasks should attempt to reduce these risk factors. Examining the layout of the work area to help identify tasks which may contribute to cumulative trauma is necessary. The following list(Putz-Anderson, 1988), describes ergonomic concerns that, overall, should be minimized at the work area:

Jan 1, 1997

During incineration of municipal solid waste (MSW), various environmentally harmful elements and heavy metals are liberated partly into bottom ash, and partly carried away with the off-gases and subsequently trapped in fly-ash. If these waste incineration residues are not properly processed and immobilized, it can lead to secondary environmental pollution to the air, soil and water. The stricter environmental regulations require a higher immobilization efficiency of the waste incineration residues, which is the main objective of the present cooperation research. Within the present project, a systematic scientific research on various MSWI residues has been carried out, including sampling, low or high temperature processing and leaching tests. In the present paper, the major results have been summarized. The research results reveal that through appropriate combined pre-processing and high temperature vitrification, the bottom ash and fly ash can be efficiently stabilized. The results achieved provide a valuable alternative route to treat the solid residues from incinerators, and to make efficient recycling and safe utilization possible.

Jan 1, 2014

By Andrew Bamber

The introduction of pre-concentration technology into the underground narrow-vein mining scenario has the potential to change the entire economics of utilizing bulk-mining methods in these situations. An idealized integrated underground mining and processing system, comprising elements of bulk mining, underground preconcentration and backfill systems is presented. Through simulation and a systems engineering approach, the implications of enabling the utilization of bulk mining methods in a narrow vein deposit through the adoption of this technology is considered. Parameters considered include orebody characteristics, ore mineralogy, grade, metal value, mining rate and cost.

Oct 1, 2004

By S. S. Klima, J. A. Organiscak

Researchers at the National Institute for Occupational Safety and Health (NIOSH) performed laboratory testing to examine and improve airborne dust capture and methane removal performance of flooded-bed scrubbers on continuous mining machines using a blowing face ventilation configuration to reduce respirable dust exposure to shuttle car operators. Several testing conditions were examined to minimize shuttle car operator dust exposure without adversely affecting continuous miner performance and production. Curtain-to-face setback distance of 9.1 m versus 15.2 m (30 ft versus 50 ft), face ventilation airflow of 226.5 m3/min versus 339.8 m3/min (8,000 ft3/min versus 12,000 ft3/min), and the use of side-body-mounted blocking sprays (on versus off) were the three primary parameters compared. Scrubber airflow was set and maintained at 198.2 m3/min (7,000 ft3/min) throughout testing. An examination of slab cuts versus box cuts and the location of the shuttle car (present behind the continuous miner versus not present in the entry) was also performed to demonstrate the effects of these constantly changing scenarios on scrubber performance. Results show that the best blowing face ventilation setup for minimizing shuttle car operator dust exposure for the tested parameters uses a 15.2-m (50-ft) curtain-to-face setback with 339.8 m3/min (12,000 ft3/min) face ventilation while operating the side-body-mounted blocking sprays. INTRODUCTION Coal mine worker overexposure to respirable coal dust continues to be a problem in U.S. underground coal mining operations, potentially leading to coal workers’ pneumoconiosis (black lung). The U.S. Mine Safety and Health Administration (MSHA) requires that respirable dust exposure to coal mine workers does not exceed a 1.5 mg/m3 average over the actual working shift (79 Fed. Reg. 24814 (2014)). Although using a blowing face ventilation configuration on continuous miner (CM) sections is beneficial for removing methane emissions from the mining face, it can be detrimental for dust control for shuttle car (or ram car) operators and any other workers on the return ventilation side of the CM when compared to exhausting ventilation. Even with machine-mounted scrubbers on CMs, shuttle car operators still have some of the higher dust exposures with blowing face ventilation systems (NIOSH 2011, Beck et al. 2015). Although scrubber discharge air is not completely clean, dust being blown around the scrubber inlet and therefore not being captured by the scrubber can further increase these dust exposures (Goodman 2000). Dust control problems are also caused by inadequate face ventilation quantities causing scrubber face airflow recirculation issues (Schultz et al. 2010). In order to minimize respirable dust exposures on blowing face ventilation sections, ventilation, water spray, and scrubber parameters were experimentally examined to improve operating ranges for both dust and gas control. Several blowing face ventilation factors were examined with respect to CM spray systems and scrubber operation. Curtain-to-face setback distance and side-body-mounted blocking sprays were previously examined in the laboratory for dust control on a full-scale CM model using a scrubber on a blowing face ventilation system (Goodman 2000). The blocking sprays produced larger dust reductions at the CM’s rear corners and return for a 6.1-m (20-ft) curtain setback distance as compared to a 12.2-m (40-ft) curtain setback distance with equal face and scrubber airflows of 169.9 m3/min (6,000 ft3/min). Because face ventilation airflow quantities, shuttle car operator locations, and tracer gas concentration gradients were not previously examined during these experiments, additional research was required to determine improved operating parameters for blowing face ventilation systems.

Jan 1, 2019

By J. A. Barsin

Stationary air pollutant sources established prior to the New Source Performance Standard (NSPS) are not, at present, subject to federal emissions regulations. However, proposed legislation could require many existing stationary sources to reduce emissions. This paper will report upon the laboratory work undertaken to date by B&W to commercialize a limestone system for sulfur capture both in pulverized coal and cyclone coal-fired utility boilers. Updates will be provided on the US EPA/State of Ohio/Ohio Edison/B&W sponsored pulverized coal full-scale limestone injection demonstration, and on the EPRI/Baltimore Gas 8 Electric, Atlantic Electric/B&W sponsored laboratory-scale cyclone coal limestone injection investigations.

Jan 1, 1986

In todayÆs evolving and globalised world, mining companies are being pressured to move beyond compliance towards long-term sustainability and sustainable development. Companies are expected to æengageÆ communities and measure the success of these engagements without a clear understanding of æhowÆ to do this. This move, away from compliance, develops more of a focus on sustainability and æcommunityÆ social responsibility rather than corporate social responsibility. This shift leads to the development of world-class projects that provide sustainable development for people, reduce the incidence of costly delays, and promote good global citizenship for companies. The process of æengagingÆ communities in mining project design and development leads to sustainable development, a stronger license to operate, and a reduction in social and political risk. To create this mutually beneficial relationship between communities and companies, communities must be æengagedÆ in the project development and risk assessment processes as early as possible, preferably during the exploration or the concept phases. How to create this æengagementÆ and manage this risk will be discussed.

Jan 1, 2007

By AIME AIME

WITH the recent increase in the price of gold, its economic recovery at depths formerly considered impractical has become a present possibility. Two important difficulties must be met: pressure bursts of the rock, and the reduced efficiency of human labor subjected to the higher temperatures and the increased humidity at the greater depths. In the following abstract of a paper by J. H. Dobson, presented before the South African Institution of Engineers on

Jan 1, 1935

By V

"Recent regulations, as well as a general aversion to central dust collectors within the Powder River Basin Coal user’s community, have created a need for an alternate method for eliminating airborne dust. This paper addresses the capital expenditure as well as the cost of ownership of an integrated point source air cleaning system in comparison to a central collection system. This assessment was conducted by comparing the cost to purchase and operate a central dust collection system and integrated air cleaner system on a typical multiple transfer point application. The central dust collector consists of a negative pressure blower, a series of filter bags, a collection hopper, a screw conveyor to place collected material back into the material stream, and a series of ducts to pull air and dust from individual pickup points. The point specific integrated air cleaners consists of a negative pressure blower to pull dust and air from an application point through a bag-less filter media located at the application point. The agglomerated material is then redeposited into the material stream at point of use without the need for ducting or a central material hopper. The assessment yielded a 54% reduction in capital expenditure and a 26% reduction in operating costs for the same application when using individual dust filters as opposed to a central system. In addition to the lowered cost, there are reductions in risk associated with the elimination of ductwork and the central containment enclosure for collected explosive dust. By the conclusion of this paper, the reader will have a better understanding of the quantifiable differences between a central dust collection system and a set integrated air cleaner systems. BACKGROUND Spillage has always been a problem in the bulk solids handling industry. As long as there have been conveyors, there has been spillage. Spillage is material that falls off a conveyor belt and creates a hazard in the environment around a conveyor belt."

Jan 1, 2016

By F. A. McLean

Given a promising claim and the required financial backing to develop it, the first problem that confronts the mine operator is usually the selection of the necessary compressed air plant. The size and type of drive are questions that naturally follow, the former being determined largely by the amount of money available and the speed with which it is desired to carry on the programme of development. The type of drive, such as electric motor, steam or oil-engine, depends on local conditions and has an important bearing on the cost of operations. ns. Few prospective mine operators are fortunate enough to locate claims within the service radius of electric power-lines, although this is more likely to happen nowadays than formerly. In the majority of cases, however, some other form of prime mover is necessary. When wood or coal are available at moderate cost, a small steam-driven plant is usually chosen. Such plants are often arranged so that they can be converted to electric-drive should future developments at any time make this desirable. Many plants of this type are installed in northern Ontario mines. When wood or coal are costly or difficult to transport, oil-engine driven mining plants have many advantages in their favor, and are now quite commonly used. Oil in some locali-ties is considerably cheaper than wood or coal, and is much easier to transport over bad roads.

Jan 1, 1924

By B Rouvray, R Bertuzzi

The development of a design-and-construct tunnelling project in Australia from its concept to its construction requires designs to be prepared and reviewed at several distinct stages prior to documenting ‘for construction’. On recent projects the post-tender stages have been variously called 30 per cent—70 per cent—100 per cent; or concept–substantial–final; or system definition–preliminary–critical. The design is reviewed at each stage by the designer’s internal reviewer, the contractor and its independent advisor(s), the owner and its independent advisor(s), the project’s independent certifier, proof engineers and often third-party stakeholders and their advisors. Documentation for each stage often dominates the design effort, at times distracting from design. This paper presents the authors’ experience of this design-and-review process. Comparisons of design budget and actual design spend and design program implications are presented. It is postulated that a subtle change has occurred in our industry that has diminished the value of the design dollar. Is there a better process? An alternative is suggested.CITATION:Bertuzzi, R and Rouvray, B, 2014. Reducing the cost of tunnel design in Australia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 501–506 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By K Henley

One of the greatest practical difficulties of measuring airblast occurs when a significant wind is blowing onto the microphone. Small windscreens are usually used to mitigate the wind noise on the microphone, but in some wind conditions, sound pressure levels (SPL) of over 120 decibel (linear) are frequently recorded. There are no specific procedures to mitigate the effect of wind noise when measuring airblast in any of the standards or guidelines pertaining to the measurement of airblast from blasting operations, other than the requirement to use an effective windscreen. A search for relevant literature was undertaken and measurements were taken over a period of six months at a test site using alternative microphone measurement methods. Previous researchers’ experiments with windscreens in silenced wind tunnels showed that wind noise can be reduced through the use of large diameter windscreens, and that at low frequencies, the windscreen size and the material type makes no difference to measured SPL values. Other researchers found that wind turbulence caused significant SPL measurement problems. A comparison with field data failed to explain the extremely high SPL recorded by the field microphones at wind velocities much lower than those used in wind tunnel testing. It has been concluded that turbulent airflow over and behind the microphone is a significant contributor to extraneous noise in airblast measurements in windy conditions. This turbulence can be generated by objects upwind of the microphone or by the microphone itself if the windscreen is ineffective. Reducing the wind speed over the microphone by placing it on the ground is the approach required by the international standard for the measurement of noise from wind turbine generators (IEC 61400–11). This paper presents data that illustrates the extent of the problem, reports on the trial of three different microphone mounting locations for measuring airblast from blasting and concludes that in windy conditions, microphones placed on the ground substantially avoid wind problems and do not reduce the measured SPL of the airblast.CITATION:Henley, K, 2015. Reducing the effect of wind on airblast measurement during blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 485–492 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S. P. Cashin, D. Kashuba, W. Esplin

Barrick has had 6 autoclaves in operation at the Goldstrike Mine, North of Carlin Nevada, since 1993. The 6 autoclaves operate in parallel, processing slurry of gold ore. The gold in the ore is predominantly associated with, and encapsulated by, sulphide minerals. It is necessary to oxidize at least 90% of the sulphide mineral before the gold can be concentrated using a cyanide/carbon-in-leach (CIL) circuit. Sulphide oxidation chemical reactions occurring in the autoclaves are exothermic; however, the sulphide content in the ore is not high enough to operate the autoclaves in an auto-thermal mode. Heat from steam is added to the first 2 of 5 autoclave compartments to initiate the sulphide oxidation reactions. The steam used to heat the autoclaves is supplied by three boilers, which are fuelled with propane gas. The completion of a few operations and maintenance projects in the last 2 years has resulted in a 50% reduction in propane energy requirements. The autoclave operating temperatures were minimized. Excess oxygen addition was held as low as possible. The material of construction for the compartment walls inside the autoclaves was changed from brick to Titanium metal. And, the speed of the autoclave slurry agitators was increased. All of these activities had an impact on the propane energy requirements of the autoclaves. Presented below is a description of the autoclave systems, and a discussion of how the energy needs were reduced, resulting in significant operating cost savings.

Jan 1, 2004

By H Benzer

Grinding clinker to finished cement consumes more energy than any other comminution process. World production of cement in 2009 was 2840 million tonnes and the energy required for comminution was 40-60 kWh/tonne depending on the clinker characteristics and the fineness of the finished cement. Machines used include single and multi compartment ball mills, HPGRs, vertical roller mills, centrifugal air separators, V separators, screens and crushers. The circuit most commonly used consists of a closed circuit HPGR followed by a single compartment ball mill and an air separator, and in operation the variables are adjusted to obtain maximum throughput with no loss of quality of the separator fines.A common objective in cement plants is to reduce energy consumption without affecting the particle size in the finished cement and simulation is used as one procedure to achieve this. Models are now available for all the machines commonly used in clinker circuits and circuit optimisation studies using simulation have been carried out in many plants leading to decrease in energy consumption per tonne of cement. In this paper the models used will be discussed briefly and several case studies will be reviewed which will highlight the effect of change in ball size in a two compartment mill, the role of the HPGR in an HPGR – ball mill – air separator circuit, and the use of a high intensity vibrating mill for producing finished cement with high additive ratio.

Aug 8, 2011

By A Tsang, D La Rosa, L Julian, W Hunt, R Pratama

Mineral extraction is facing the twin challenges of finite resources and increasing environmental and economic costs. Society’s growth is matched by an increase in demand for the earth’s resources. It is incumbent on us as contemporary mining professionals to promote and facilitate ethical and efficient practices. Technological developments have and will continue to allow a decrease in viable cut-off grades, creating new economic opportunities from deposits that were previously uneconomic. Mining low-grade deposits however, even with perfect recoveries, will have a significant environmental cost for the metal won. The greatest opportunity to increase metal with the least environmental cost is to increase the metal yield from existing mines. The determination of mining polygons is a critical juncture where rock is typically subjected to the binary grading of either ore or waste. This is undertaken using a number of factors, such as the mining equipment being used and the recovery in the processing plant. Traditionally, mining polygons were generated on the in situ grade control model. This ignores the complex differential blast dynamics that occur during blasting. Two opportunities exist to improve metal yields: optimise the blast design to achieve the post-blast muck pile that will support the greatest outcome; and generate optimised polygons on the post-blast muck pile. A data set from a Canadian Gold deposit is used to demonstrate the potential benefit of iterative blast movement modelling and grade control polygon optimisation on metal yield. The impact of blasting on the total recoverable metal is presented, highlighting blast design as a critical process in the mining value chain.

Sep 1, 2024

By W. D. Monaghan

Flame cutting and welding is one of the major causes of fires and explosions in underground U.S. coal mines. On May 20, 2006, a flame cutting operation at the Darby Mine No. 1 led to an explosion that resulted in five fatalities. On January 22, 2003, another explosion caused by flame cutting at the McElroy Mine resulted in three fatalities and three serious injuries. On June 22, 1999, a flame cutting and welding operation at the Loveridge Mine caused a fire that resulted in sealing of the mine for an extended period. Finally, on March 19, 1992, an explosion at the Blacksville No. 1 Mine that was caused by welding resulted in four fatalities. The National Institute for Occupational Safety and Health (NIOSH) conducted a study on fires and explosions in underground U.S. coal mines that were caused by flame cutting and welding operations to determine the root causes of these types of fires and explosions. The methodology included interviewing mining personnel who perform flame cutting or welding operations in underground U.S. coal mines and visiting mines to observe these operations, and MSHA reports of investigations and accidents statistics were analyzed. The results were used to identify and compare differences between flame cutting and welding practices and techniques in small and large mines, Eastern and Western mines, low seam and high seam mines, room and pillar and longwall mines, and between experienced miners and new miners. As a result of this study, best practices and interventions were developed to reduce the number of fires and explosions caused by flame cutting and welding. This paper provides a summary of this work. Disclaimer: The finding and conclusion in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupation Safety and Health.

Jan 1, 2009