Search Documents

By S. P. Chong, Peter V. Avotins

The iron and steel industry continues to operate at depressed production levels due to the low level of demand for steel and foundry products. Crude steel production in the Western world dropped by 13.7% from 459.3 Gt (506 billion st) in 1981 to 396.4 Gt (437 billion st). The reduction was particularly severe in North America where the industry suffered a loss of 37.3% from 123.6 to 77.5 Gt (136 to 85 billion st). This reduced level of production severely affected iron ore and agglomerates output. Substantial curtailment was made in both sintering and pelletizing plants to meet reduced demand. The pressure on these plant operators shifted from quantity to quality. With energy cost becoming an ever increasing part of production costs, conservation was a major area of emphasis. Iron Making Sinter has continued to be the favored burden for blast furnaces overseas. As hot metal production declined and excess sintering capacity developed, many of the overseas operators that have been using pellets found it advantageous on hot metal production cost to increase the ratio of sinter at the expense of pellets. This was the case despite the depressed price level of pellets in the world market. In North America where pellets have been the predominant burden material-mainly because it is necessary to pelletize the fine grain iron ores available domestically-there was also increased interest in sinter usage. Bethlehem Steel Corporation's 13.6-m (44.5-ft) furnace at Sparrows Point experimented with a burden with more than 70% of sinter during the second half of the year and indicated some favorable results as compared to its previous 50% super flux sinter and 50% acid pellet burden. The blast furnace operators continued to press for improved burden quality. In addition to the emphasis on the importance of burden chemistry and quality, uniformity, much emphasis was placed on improving reducibilitiy and high temperature metallurgical qualities. These burden properties were recognized to hold further promise in reducing fuels rates. Sintering With reduced consumption caused by the cutback in hot metal production, many sinter plants sat idle while others operated at greatly reduced rates. The deemphasis on production in many plants allowed them to experiment with various means to reduce operating costs. The most notable action was the introduction of low cost South American pellet feed fines into the sinter ore mix. These feed fines, which are finer than 150 µm (100 mesh) ore, were previously thought to be too fine for sintering. However, when the full production rate is not required the use of up to 40% in the ore mix was reported to be successful with the aid of burnt lime and adequate premixing and granulation of the sinter mix before sintering. The emphasis on quality and tighter cost control also has resulted in a further breakthrough in sintering technology. It was recognized that good feed preparation-including selection of compatible ores, good blending, good pseudo-particle formation, additive size control increased bed depth, and closed control of the sintering bed heat pattern-could allow the production of high quality sinters with much lower heat input and FeO level. Bed depth of more than 600 mm (23.6 in.) was practiced in a number of operations. Total heat input of better than 1.3 GJ/t (290,300 kcal per st) has been achieved. Kawasaki Steel's Chiba Works has also achieved a 5.3% SiO2 in the sinter with good quality. The low heat input approach allowed production

Jan 5, 1983

By R. J. Morlock

Prior to 1912, coal research for Republic Steel, Corporation was limited to a periodic box test conducted in a commercial coke oven. Then in 1912, a Koppers movable-wall test oven was -built to research wall pressures for selected blends and to conduct other varied research work. In the 1950's economic pressures caused a reassessment of position resulting in the establishment of a Coal and Coal Chemical research group in 1956. In 1958 this group, along with other groups of research endeavor were incorporated into the new Republic Steel Corporation Research Center at Independence¬ Ohio. Currently this section is divided into four groups. 1) Coal Preparation, 2) Coal-Chemicals, 3) Coal Characterization, and 4) Coal Carbonization. The objective of each group is described, and a brief listing of the work done under the first three groups is indicated. A more detailed description of the studies by the Coal Carbonization group of the coking characteristics of Republic Steel Corporation's coals as blended among themselves or in conjunction with selected purchased coals follows. The wall pressure, contraction, and stability index criteria are specified, and the method of assessing these criteria as a function of blend composition is indicated.

Jan 1, 1963

By E. R. Kaiser

ACTIVITY on long-range and on immediate wartime problems shared the attention of specialists in coal research during 1943. Programs of the principal coal laboratories were more adequately financed than in previous years, but all reported shortages of technical personnel. Expansion in coal research in the year to come will depend primarily on the availability of qualified research talent.

Jan 1, 1944

By Ronald D. Hill, Elmore C. Grim

1. Potential groundwater pollution resulting from large-scale surface mining in western states should be evaluated. 2. Criteria should be developed for the design, construction, operation, and abandonment of sediment ponds for maximum removal of suspended solids. 3. Methods should be developed for reducing suspended solids discharges from surface mines to less than 30 milligrams per liter. 4. A manual should be developed in the form of guidelines for sediment and erosion control planning and implementation. These guidelines must be designed to cover all phases of the coal surface mining operation (i.e., before, during and after mining). 5. A mine road manual should be developed for use by surface mine operators and State and Federal Agencies. Erosion, water control, and dust control should be covered in detail. 6. The block-cut, head-of-hollow fill, and mountain-top removal methods and techniques of contour mining should be evaluated, designed, and ultimately demonstrated in steep, mountainous terrain. Designs should be prepared for single and multiple seam applications. The demonstrations must show that these mining systems will secure rapid achievement of reclamation require¬ments and provide maximum, safe, economic coal recovery in an environmentally safe manner. 7. A Blasting Manual should be developed for use by industry and enforcement agencies. Stress should be placed on how to keep vibration levels and air blast pressures well below accepted safe criteria. Also, methods that can be used to control noise should be listed. 8. Investigations should be conducted on the effect of continued vibrations from blasting on structures that are near quarries. 9. Additional guidelines need to be developed for sampling and analysis of overburden material and associated coals for trace elements and noxious strata. Samples are extremely sensitive, and the source and manner of their collection, handling, storage, and treatment, as well as the techniques of analysis, need to be developed and described. This information can be used to predict possible future problems.

Jan 1, 1974

By Richard Burt

"In seeking to supply the ever increasing needs for raw materials, the mining industry has been required to develop lower grade resources in increasingly remote regions of the world. This has resulted in the extension of many frontiers, both technologically and geographically.The accent of mineral processing research over the last few decades has been to “do existing things better”. There have been many breakthroughs in equipment and processes; however in general the accent has been to increase capacity of existing unit processes, often by orders of magnitude, or to refine the process itself by basic research and development. This has lead to added sophistication, enabling the process engineer to maintain optimum performance of his equipment while reducing the cost, and the amount of labour needed to operate the plant.While much of the increased requirement for resources is handled by the development of ever larger, lower grade orebodies, a significant portion still comes from the small miner - even the artisanal miner - operating in remote and often politically sensitive parts of the world. For them, innovation and simplicity are the keys, not sophistication.The tension between sophistication and simplicity - or research and reality - is specially evident in the area of gravity concentration of rare metals, such as tin and tantalum. This paper looks at this tension, primarily from the eyes of an operator and seeks to put into perspective the two paradigms."

Jan 1, 1999

By Anthony William Deller

MAJOR battles in the present war have been fought in American research laboratories. Without the outstanding contributions made by our scientists, engineers, and technologists in mining and metallurgy, many of our achievements in the present war would have been impossible. All recognize the fact that modern research has found the answer to problems which seemed insuperable. For the duration, many of these inventions must be maintained as war secrets. But aside from these, the record of accomplishment in peace and war, especially in the past few decades, known to all, demonstrates what scientific and industrial research can accomplish. It may be regarded as axiomatic that the development of modern industry is based principally upon research devoted to making inventions and discoveries. We have come a long way from the sixteenth century, when Agricola published his classical "De Re Metallica:" With our vastly increased knowledge we are now commercially producing dozens of metals entirely unknown at that time. Further, with our modern methods of research and development, a large number of invaluable alloy compositions have been produced. These include numerous age-hardenable alloys, cupronickels, "Everbrite", "Everdur", "Duralumin", "Elinvar", "Hastelloy", "Inconel", "Invar", "Monel", "Ni-chrome", "Ni-Hard", "Ni-Resist", "Permaloy", "Silcrome", stainless steels and irons and other alloy steels, "Stellite", and zinc die-casting alloys.

Jan 1, 1945

By Donald F. MacDonald

WE are living in a mineral and technological civilization. The Encyclopedia Britannica defines civilization as follows: "It is the final test of a progressive civilization that a given effort shall produce a larger modicum of average individual comfort, and the pursuit of this ideal has been from first to last the impelling force which drives civilization onward". This "individual comfort" demands labour-saving machines and devices such as motor cars, radios, and thousands of other inventions, most of which require minerals and metals in vast quantity for their manufacture. In fact, more minerals and fuels have been used in the last third of a century than in all previous world history. Since 1800, the world's production of metals has increased more than a hundred fold (1). Scientific discovery is now advancing on a wide front, thanks to the research work that is being carried on in progressive countries. The world's work is now being done with very much less human drudgery than in the past. We do not have to toil for our living as our ancestors did, even if we follow their occupations. The average man has had many years added to his life-span, but, apparently, little to his spiritual stature and less to his common sense.

Jan 1, 1939

By Volovik A. V. Ivtan, Shelkov E. M. Ivtah

"One of the most power consumption Industrial process is production of Al from bauxites (about 45000KWt.hour electrical energy for production of 1 ton. of technical Al). This process is based at the low efficiency and productivity electrolysis technology.Last years IVTAN investigations give to .us information about possibility to use of high temperature shaft- furnaces for efficiency production of alumina (AL2O3 ) technical. aluminium and some all.oys on the base of the high temperature carbon- thermal reduction process. At this case power consumption for production of unit of last, product will be less at the 3-4 times.The carbon-thermal method is allow produce alumina (Al203 ), technical Al and its alloys not only from deficient bauxites, but practically inexhaustible reserve of other types of Al-contain row materials (cianite, sillimonite and so on/The thermal-chemical economical analises of fulfilled at the IVTAN, production of alumina. Base on facts of production and technical technology are especially for ones arguments at the high temperature shaft-furnace technical Al and its alloysIn the last decades of the 20-th century, the discharge into atmosphere of high temperature and. combustion gases places . problems before humanity more and more sharply and becomes of great importance task.But at the same time, as production of material values increases, intensity of pollution of environment increases all time. And the value of new processes and. technologies of material production, aimed at reducing the expenditure of power and pollution of· the environment, also increases."

Jan 1, 2000

By R. P. Aikman, F. G. Miller, J. M. Podgursky

In response to the growing demand for low-sulfur coking coal for iron-making, the coal industry is continually striving to perfect methods for cleaning coal to acceptable ash and sulfur levels while maintaining maximum product yield. By present standards the industry has adequate processes for cleaning coarse coal, (i.e., +28 mesh) at almost any desired specific gravity. However, in the case of fine coal (i.e., -28 mesh) neither of the two existing processes-froth flotation and hydrocycloning-in its present state of development yields products that are comparable in ash and/or sulfur content to products normally obtained from coarse coal processes. The work outlined in this article is part of a larger study directed toward maximum exploitation of froth flotation for fine coal processing. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of froth flotation with other fine-coal processing methods.

Jan 7, 1967

By W. H. Bassett

ABOUT twenty-five years ago the copper industry had outgrown the Lake Superior production. The electrolytic copper producers had- their process well in hand and the industry was well started in the use of electrolytic copper, both for working into wire and sheet, and for the making of alloys. The trade knew that some brands of copper made good material and that other brands did not. There came together a group of men-a refiner, a rolling-mill man, and a manufacturer of electrical machinery-each of them desiring to know why there was a difference and what .it was. Much investigation was done with wire bars and cakes which involved ' chemical analysis, metallographic examination, physical tests and electrical tests. To find the influence of different kinds of copper in making brass 200 carloads of ingots were made into ,eyelet brass under careful observation; each carload was carefully analyzed and tested before used. The alloy was made and rolled under standard conditions and the results recorded.

Jan 1, 1924

By Enrique Hauser

FIRE-DAMP is a mixture of methane with other inert gases or combustible gases. The inert gases in question are carbonic acid, water vapor, nitrogen, etc. The combustible gases are hydrogen, ethane, etc. The study of the properties of fire-damp, therefore, becomes a study of the properties of methane and the influence on its properties of the different gases we have mentioned. Characteristic Properties of Methane 1. Respirability.-Methane being a paraffin is characterized by its weak chemical affinities. From the physiological, point of view one could substitute it for nitrogen of the air at least momentarily, without experiencing any difficulty in breathing the mixture consisting of 21 per cent. 02 + 79 per cent. CH4. I .have tried this on myself, making the gas exhaled -from the lungs burn subsequently in a Bunsen burner.1 From the chemical point of view, this weak affinity permits the gas to be burned in certain circumstances with hydrogen and oxide of carbon in an oxygenated mixture, with the result that the last two gases achieve only a fractional combustion. This practice has been utilized with success in the methods of analysis which I have perfected and which I describe later in this paper. 2. Retardation of Flashing Point.-A characteristic property of methane is its retardation of flashing point, noted by Davy in 1816 and studied by Mallard and Le Chatelier in 1883.2 Taffanel and Le Floch have recently confirmed these results.3 Let us recall the nature of this retardation:

Jan 2, 1916

By Enrique Hauser

Discussion of the paper of ENRIQUE HAUSER, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 521 to 534. GEORGE A. BURRELL, Pittsburgh, Pa. Mr. Hauser determined the influence of inert gases on the properties of fire-damp mixtures, and one might take some issue with his work on the effect of hydrogen, on those mixtures. It is valuable information to have, but as far as the practical application of it goes, it is not of much significance, because one does not find it in mines, at least not in any appreciable amount. The same Fig. 1.-APPARATUS FUR DETECTING COMBUSTIBLE GASES IN AIR. thing can be said of ethylene. Ethylene is formed in considerable quantities as a product of heat reaction, but normally, in the coal mines, as a result of a great many analyses we have made at the Bureau of Mines, we cannot say that ethylene is a combustible gas found in the fire-damp in coal mines.

Jan 5, 1916

By Yuanbo Zhang, Zhixiong You, Daoxian Duan, Guanghui Li, Tao Jiang, Xiaohui Fan

"Presently, high-grade manganese oxide ores are usually utilized by a coal-based reduction roasting process. However, there were some obvious drawbacks, including serious environmental pollution, high energy consumption, etc. The reduction temperature is relatively high (850-900 °C). In this study, a kind of biomass, pine black charcoal, was used as a reductant to reduce low-grade manganese oxide ores. Under the optimal conditions of reduction temperature of 600~650 °C, roasting time of 30~45 min and ratio of ore to reductant 5:1, the leaching efficiency of manganese reached more than 98%. Compared with the traditional coal-based reduction process, the reduction temperature is reduced by 250-300 °C.IntroductionManganese plays a very important strategic role in the national economy, and it is widely used not only in the metallurgical industry, but also in the light industry, chemical industry, medicine, agriculture, etc [1]. The average grade of manganese ores in China is evenly about 21%, which belongs to typical low-grade manganese ores [2]. Therefore, large quantity of high-grade manganese ores is required to import in order to meet the rapid development of Chinese manganese industry. As reported, the conventional treatment of reduction roasting has been widely applied for processing manganese oxide ores, in which coals or reducing gases (CO, H2 or CHi) were usually used as reducers [3]. However, there were some insuperable problems, such as high energy consumption, poor operating conditions, serious environmental pollution, etc [ 4-9]."

Jan 1, 2013

By Richard Akerman

(Translated by FREDERICK PRIME, JR., Professor of Metallurgy in Lafayette College, Easton, Pa.) [THE attention now being paid both in this country and Europe to the greatest economy in the working of the blast furnace, and the eagerness with which all thoughtful men in the iron business look for any new information which will tend to throw light on this sub¬ject, is a quite sufficient excuse for presenting this paper to the Amer¬ican Institute of Mining Engineers.] I. It must be borne in mind that when two bodies unite to form a chemical compound, heat is almost always evolved. In order to

Jan 1, 1873

By Evan C. Morgan G

El presente texto describe el panorama historiográfico de la mina de Condoroma, trabajos y el uso de los métodos de exploración realizados en dicha zona. Situada en el distrito de Condoroma, provincia de Espinar, Cusco, las minas de Condoroma fueron anteriormente trabajadas por los españoles, pero es a partir de 1927 y con la compañía Gibson que los trabajos mineros se reactualizan y se emplea la construcción de un tunel corta-veta de 170 metros de longitud, que al encontrarse con la veta, la extendió a 30 m. Posteriormente en 1952, se interesa la firma Mauricio Hochschild, suscribiendo un contrato de Opción por tres años con el Sr. Carlos Herrera Rozas. Firmada la Opción, se procedió primero a explorar las minas de Kata, por contener vetas vírgenes, y luego, las de Condoroma. Entre los métodos de exploración utilizados estaban los piques, las trincheras, la limpieza superficial con tractor, la perforación con diamantinas y la exploración geofísica. Finalmente, y tras haber desarrollado este programa de exploración con diamantinas, se pudo fijar los valores comerciales del yacimiento minero, aunque a un costo un tanto elevado. Empero la utilización de este moderno método de exploración, permitió revalorizar los yacimientos abandonados y colocarlos dentro de un espacio productivo.

Jul 20, 1956

By I. S. Parrish

Reserve audits have increased in recent years as more companies, especially juniors, enter the ranks of producers. Corporate and individual investors are seeking corroboration of stated reserves. The reserve audit satisfies this need. An audit assures investors that the reserves, as presented, are a reasonable and accurate approximation of the quantity and grade of the economically viable material present. The reserve audit verifies that there are no fundamental errors in logic, style or the data base, and that the reserves, as given, may be used for mine planning or economic forecasting. Reserves that pass an audit may be used with confidence in preparing cash flow projections and in deriving net present value or internal rate of return on any given project. This article describes what a consultant does while performing the reserve audit. In performing an audit there are four general areas of concern that must be checked: definitions, parameters, data and procedures. In each of these, the auditor must convince himself that the reserve study has complied with governmental regulations and guidelines, professional standards and industrial practices. Any deviation from these norms must be identified and its effect upon the appropriateness of the reserves evaluated. By concluding that a reserve study passes his audit, the reviewer is stating that there are no fundamental errors in logic or style and that spot checks have revealed no substantive errors in procedure or mechanics. The responsibility for the reserves remains with the entity that compiled the original study.

Jan 1, 1990

By Jerry D. Pfarr, Gary Loving, David G. McDowall

Introduction The Open Cut is one of the best known landmarks in South Dakota's Black Hills. It is the site of the original discovery of the Homestake ledge, or lead, in 1876. Between that time and 1945, the Open Cut produced about 36 Mt (40 million st) of gold ore, the majority of which was drawn from underground operations. In 1981, a drilling program was undertaken to determine how much ore the old timers left behind. The results of this study indicated an ore body made up of broken and caved ground, and solid blocks in pillars and crowns. Reserves are estimated at about 6.8 Mt (7.5 million st) of gold ore, grading at 4 g/t (0.116 oz per st). Total tonnage of material, including waste, is estimated at more than 60 Mt (66 million st). The mining plan is a combination open pit and underground operations. The bottom 78 m (255 ft) will be mined by the underground panel-caving method. The open pit was designed as a contractor operation up to the expected milling stage or the point of sustained ore production. The pit was designed to avoid disturbance of US Highway 85 near Lead, SD. In 1983, the South Dakota Board of Minerals and Environment approved the mining and reclamation plan. Test mining began in the north of the Open Cut using open pit methods. Upon completion of the test pit, Homestake Mining's board of directors approved an expanded mine plan. They committed an additional $27.1 million to prestrip the ore body that is expected to yield 23 t (750,000 oz) of gold. Project life is estimated at 15 years. Exploration program In early 1980, 10 diamond drill holes were drilled from the surface in the vicinity of the east side of the Open Cut. The reserves delineated by that drilling were too small to justify their development. A continuation of this study attempted to quantify the tonnage remaining in the bottom of the Open Cut in the crushed remnants of old stope-and-crown pillars. This was originally thought to be minable by improved drawhole methods using highly mechanized procedures. By early 1981, however, thinking turned toward surface mining methods. The effort to quantify minable ore tonnage ultimately involved drilling 385 reverse-circulation rotary drill holes. These were drilled from August 1981 to March 1983 in several groups of holes. Each group, or drilling program, had a slightly different immediate goal or purpose. The holes were drilled to various depths using truck-mounted Drill Tech 40 drills with doublewalled 76 mm (3 in.) pipe with 134 mm (5.25 in.) three-cone rotary bits. Initially, wet drilling was employed using a cyclone collection system. Since cutting recovery was not as high as it should have been, all subsequent drilling was dry. The cuttings were collected and deposited by way of a cyclone into the sample bag. The pickup for the cuttings using the three-cone bits was about 50 mm (2 in.) above the bottom of the hole. Overall cutting recovery for the drilling program was estimated at 75%. Samples were taken on each 1.5 m (5 ft) of hole drilled. Each sample was split into three 48-g (1-2/3 assay ton) charges. The accepted value was the straight average of the three charges. Because of the known "nugget effect," assays were nearly impossible to duplicate. Therefore, to validate the regular assays, a series of screen fire assays were run. Based on this method of assays and checks, it was concluded that 10% more ounces would be produced than indicated by mine grade. Test pit The northernmost portion of the mine as planned is known as the Terraville test pit. This portion was mined ahead of the rest and separately. It provided answers to questions on slope stability, reserves correlation, mill recoveries, mining costs, and surface mining conditions in various weather and ground conditions since many boulders and much timber were expected. The mining plan for this portion of the pit was successful. More ore was mined than was expected. Mixing of Open Cut ore with underground ore in the mill feed was successful. Impact on the surrounding communities

Jan 10, 1987

By N. B. Prenn

Many recent projects have been developed and mined based upon imaginary reserves. Imaginary or "geo-fantasy" reserves have cost many companies millions of dollars. The significant and varied technological advances in the mining arena have done little to curb reserve calculation problems. These advances may have served to increase the prevalence of reserve problems by putting more tools in the hands of personnel not properly trained or experienced in reserve estimation. This paper will discuss potential problems related to calculating reserves, which include: SAMPLING ERRORS -obtaining a representative sample. -Decay analysis of wet RC drilling -Bias introduced by sample preparation. -Assay bias; Coarse gold. -Specific gravity samples. GEOLOGICAL ERRORS -structural boundary definition. -Separation of high grade and low grade zones. -Incorrect continuity assumptions MODELING ERRORS -Too much influence of high grade samples. -Improper method of calculation. -Assumed range of influence. -Errors in the data. ENGINEERING ERRORS -Inaccurate assumptions. -Inadequate metallurgical testing. -Designed bottlenecks.

Jan 1, 1992

Mining has traditionally been seen as a relatively risky business. Exploration is expensive and the failure rate is high, while start-up costs commonly run to many hundreds of million dollars. To justify the risk and expense, the returns from successful projects must also be high. Accurate estimation of mineral resources and reserves is fundamental to the processes of optimising returns and managing risk in mining developments. Systematic development from initial exploration through a series of development stages enables expenditure and risk to be balanced. As a consequence, large scale modern mine are more akin to manufacturing businesses. This paper examines the life history of a mineral reserve estimate from the perspective of a large mining company against a background of modern estimation and reporting requirements. It will also touch on what constitutes, in the author's opinion, `best' practice in reserve estimation, and how this concept can be spread more widely. [Abstract to be re-written and reduced to 100 words]

Jan 1, 2003

By A. G. Pasamehmetoglu, N. Celebi, K. Erarslan

A deposit evaluation system has been developed for a proposed new mine in the basin around Collolar in Turkey. It includes compositing, gridding and reserve estimation facilities and takes account of the economic value of the pit and the pit bottom elevation

Sep 1, 1991