Search Documents

By Francisco Geraldo Toledo Junior

Os aços inoxidáveis possuem características essenciais para um bom acabamento quando o que se busca é estética e boa resistência à oxidação. Quando se específica um aço inoxidável, o acabamento é um dos aspectos relevantes que devem ser considerados. O acabamento possui uma importante influência em algumas características do material como, por exemplo, na facilidade da limpeza e na resistência à oxidação / corrosão. Há uma grande variedade de acabamentos. Através de ensaios de oxidação a quente, medição de potencial eletroquímico, medição de dureza a baixa carga (microdureza) e medição da tensão residual via difração de raios x foi possível perceber uma diferença entre os acabamentos 2D, 2B, RO, BB, Nº4 e Nº6. A medição de tensão residual mostrou qualitativamente que o aumento de dureza e o forte amarelamento ocorrido no material com determinados acabamentos é função de uma deformação elástica na superfície imposta durante alguns dos processos de fabricação desses aços. Esse mecanismo é relevante e interfere na resistência a oxidação e corrosão nos casos estudados.

Aug 17, 2017

By Noan Tonini SImonassi

A utilização de compósitos de matriz polimérica reforçados com fibras naturais vem assumindo um papel importante no âmbito da engenharia de materiais. O baixo custo, a biodegradabilidade e a redução do peso especifico torna a utilização desse tipo de compósito bastante atrativa. O objetivo deste trabalho é avaliar o desempenho da fibra de sisal como reforço do policarbonato visando uso utilização militar, especialmente em proteção balística. Antes da confecção dos corpos de prova, foi realizada a redução no tamanho de partícula do policarbonato e da fibra de sisal através de um moinho de facas, posteriormente dos corpos foram submetidos aos ensaios de tração e flexão.

Oct 30, 2017

By David Siu

Many problems were encountered with the mechanical wedge-type splices used for the 15-inch square precast prestressed concrete piles installed at an industrial plant site. Many of the wedges were breaking during installation of the splices and after pile driving resumed following splicing. Dynamic monitoring of the piles and uplift loading tests confirmed that the problems were associated with cracked or damaged wedges. More ductile, annealed wedges were subsequently used, and, while not completely satisfactory, they were found to perform better than the original more brittle wedges. Introduction Long precast prestressed concrete piles were installed to support heavy, settlement-sensitive structures at an industrial plant in Port Alberni, British Columbia, Canada. The piles were driven through soft compressible silts and clays to toe bearing in a dense sand and gravel deposit or on bedrock. Each pile consisted of two or three segments joined with mechanical wedge-type splices trademarked DYN-A-SPLICE. Shortly after construction began, problems arose during pile installation, and these problems were, later, identified to be related to the wedges, or clamps, used to connect the splice plates.

Jan 1, 1991

By Randall Wheeler

In early 2008 we were asked by a quarry to become involved in a conflict with a pipeline company concerning blasting near one of their underground high pressure gas lines. The pipeline company, without the quarry’s knowledge, had sought and obtained a temporary restraining order against the quarry forbidding them from blasting near the pipeline.

Jan 1, 2011

By D. J. Kennedy, A. W. Stokes, W. G. Klinowski

Sulphur hexafluoride (SF6) has become an accepted standard in the field of mine ventilation tracer gas studies. It has a wide variety of uses for defining mine ventilation flows that cannot be adequately described using conventional instruments such as anemometers and smoke tubes. The Cape Breton Coal Research Laboratory (CBCRL), Energy, Mines and Resources Canada, has been using SF for the past 4 years and has developed numerous release and sampling systems to increase its versatility. The CBCRL has also completed a successful field trial of an automated rapid sequential SF6 analyzer (which gives a pseudo real-time readout) that can be used underground. In doing this work, the authors recognised the potential of being able to use more than one tracer gas simultaneously in an underground study. Two alternative tracer gases (Freon-13B1 and Freon-12) have already been used by CBCRL in some of their underground work. These gases can be measured by gas chromatography utilising an electron capture detector in a similar manner to SF6. A description of these gases, the methods for 6' their handling, release and sampling are given in this paper together with a brief outline of the analytical system used to measure them. Their suitability to mining applications is compared with SF6. A study in which these three gases were used together is discussed and the results and conclusions given. Some of the additional uses for multiple tracer gases to assist the mine ventilation engineer in resolving problems and improving his day-to-day monitoring are discussed. Finally, a brief analysis of developments which can be expected in the near future is outlined.

Jan 1, 1987

By J-S. Marois, F. Cappucitti, Y. Dodier, D. Downey, G. Matton

"The flotation processes of the Niobec Mine have been affected by a seasonal loss of recovery and a significant increase in reagent consumption over the past few winters. This paper discusses the problem-solving methodology that was used to identify the root causes, to develop solutions and to implement changes that resolved the problem to restore the process to summer-like conditions year-round. Mainly, it was found that the process water was contaminated by phosphates ions, which adversely affected the carbonate pre-flotation, and caused detrimental effects on the subsequent niobium flotation. The phosphate ions were being generated by the process itself, but were consumed by algae in summer conditions. It was determined in laboratory studies that concentrations as low as 5 ppm were enough to affect the circuit and that the multiple additions of process water throughout the circuit was worsening the effect. Also, temperature was found to have an impact on the reagent performance. The performance of the plant was restored by implementing a natural treatment of our process water with a simple cost-free rearrangement of our circuit streams. In addition to that, our extensive geometallurgical program was used to provide ore to the plant restricting phosphate generation in the process. Also, a modification of the collector was developed and introduced in the carbonate pre-flotation that provided improved performance during the periods of low pulp temperature.INTRODUCTION Niobec is one the three major global producers of niobium presently in operation. Situated in the Saguenay-Lac-St-Jean region of Quebec and in operation since 1976, the site produces ferroniobium (FeNb) to be used mainly in High Strength Low Alloy (HSLA) steel, which is known to have better mechanical properties than carbon steel. The Niobec operation consists of an underground mine, a concentrator and a converter plant. The concentrator concentrates niobium-bearing minerals, mainly pyrochlore and columbite, to produce a high-content Nb2O5 concentrate which is then converted to FeNb in the converter plant by an aluminothermic reaction. The Niobec concentrator flowsheet, which has gone through many expansions and optimisation over the years, consists of grinding, desliming, flotation and leaching steps. The flotation steps are numerous, sensitive and difficult to operate due to the non-selective nature of oxide mineral collectors. Thus, the pyrochlore concentration process at Niobec still faces many challenges and is constantly going through periods of continuous improvement."

Jan 1, 2018

By Martin P. Schroeder

"Challenges have emerged as subway systems age and as new tunnels are bored in congested corridors or in high-risk environments. To help public transportation agencies address tunneling challenges, the American Public Transportation Association has convened numerous independent industry peer reviews composed of top experts in their fields to come together and provide recommendations and solutions. This paper provides case histories of peer reviews that include topics such as boring through toxic soils, boring underneath existing tunnels, retrofit of tunnel ventilation systems, and mitigation of water intrusion. Peer reviews are applicable to all tunnel projects worldwide. The paper will highlight the conditions of these challenges, peer review recommendations, steps taken to reach agreement, and the successes that resulted, which led to major changes, new legislation and reduction of risk. INTRODUCTION Public transit agencies face many challenges in maintaining and expanding safe transit operations, especially as systems age, ridership expands, and budgets remain flat. The development of new industry standards and federal safety regulations places further demands on transit systems, with compliance often taxing in-house resources. Studies of the state-of-good-repair across US public transit systems indicate a current backlog of $84 billion in maintenance projects, which will require an investment of $18.2 billion per year to eliminate the backlog by 2030[1]. Systems not in a state-of-good-repair may not operate efficiently, may not be available to meet the growing ridership demands, and may not meet required safety goals or reduction of risk. Innovation is another clear need transit agencies have for improving system performance and lowering operating costs.To meet these challenges, transit agencies often turn to industry peer reviews for guidance and recommendations as part of their overall strategy to maintain and grow the safe operation of their systems. As a service to its members, the American Public Transportation System (APTA) has developed an industry peer review program designed to give agencies opportunities to learn from each other and help them address challenges in operations, engineering design, and construction of their systems. Over the past 20 years, APTA has performed hundreds of peer reviews covering all aspects of transit system operations from fare collection to agency organization, project delivery methods to safety culture, and engineering design including tunneling and tunnel fire ventilation. As rail transit systems expand to meet increased ridership, it is often necessary to bore new tunnels for alignments in congested areas where surface rights-of-way are lacking. Such proposed alignments can pose significant challenges for transit agencies, as they contend with various tunneling problems."

Jan 1, 2016

By Mark Johnson, Mathew Janes

"The Resonator RD 260 Resonant Pile Driver delivers ground disturbance free, high production pile driving. The Resonator has recently been used on numerous production pile driving sites in the Netherlands and Melbourne, Australia to drive piles in sensitive areas where conventional pile drivers could not be used. Two case histories are provide in this paper which demonstrate the features and benefits of Resonant pile installation.. In the Netherlands the Resonator RD 260 was used at the Vopak Oil Storage facility in the Port of Rotterdam to install pipe and sheet pile within an active pumping gallery. The site demanded vibration free pile installation to construct a cofferdam within sensitive, highly valued assets. Access was an issue and schedule demands were stringent as shutdown windows were narrow. The RD 260 provided ground disturbance free piling immediately adjacent to fragile structures. At Vopak the only site access was using a large crane positioned over 40 m from the location of pile driving. Driving was conducted amongst 900 mm dia pipes carrying heated crude oil.In Melbourne the RD 260 was used to drive GU 18 sheet piling adjacent to light rail easements. The project was the first of many grade separations being constructed within Melbourne urban areas to lower the light rail and provide quieter rapid transit. The original trial used an RGT MR105 series vibrator but noise and vibration criteria were exceeded. The RD 260 was brought in for a trial and performed with high production and produced negligible ground vibration. Up to 17 sheet piles 14 m in length were driven in a 2.5 hour window during the trial.IntroductionThe Resonant Pile Driving method is gaining acceptance around the world as a new method to rapidly drive piles free of ground borne vibrations. The high frequency vibrator resonates the pile, essentially turning the pile into a spring, to excite the toe of the pile with high accelerations and low amplitude. High acceleration with low amplitude generates high penetration rates but the high frequency stress waves are quickly dissipated in the soil. Typically ground borne vibrations are measured at below 1 mm/sec within 1 to 5 m of the pile. The Resonant method can drive a pile next to a glass of wine, without spilling, as has been demonstrated on numerous piling sites.How Does Resonance Work?The Resonant method uses a hydraulic piston - cylinder geometry to generate high magnitude, high frequency oscillating force. This is a very different mechanism than the eccentric mass technology used in conventional and variable moment vibrators.A unique valve geometry achieves the high frequency flow switching necessary to oscillate the hydraulic piston at up to 180 Hz (10800 VPM). The valve is controlled electronically for maximum accuracy of the desired frequency. The volume of hydraulic oil delivered through the valve to the piston (flow rate) determines the amplitude while the hydraulic pressure determines the peak force."

Jan 1, 1900

By Y. Z. Xu

This paper presents a new dynamic method called Resonant Pile Test (HPT) for evaluating bearing capacity of pile. The basic conception of RPT is given in brief and the measuring system is also introduced. In addition, the influences of the magnitude of exciting force and of the mass of pile cap on test results are discussed. Finally, comparisons between values of bearing capacity given by RPT and by static load tests for a variety of pile types are listed.

Jan 1, 2010

By Mathew Janes

"Sheet piles remain an economic solution to many shoring problems. However, installation of sheet piling suffers high noise and vibration with conventional impact or vibratory methods or low production and high expense with push techniques. Many projects simply will not allow sheet piling due to vibration concerns.Installing sheet piles with a tunable, high frequency Resonant vibrator provides high production with imperceptible ground vibrations. Recent projects in Canada have proven the technique on production projects where vibration sensitive structures are present immediately adjacent to the sheet piling. A project in Whitehorse, Yukon required a Waterloo style impervious sheet pile barrier be driven immediately adjacent to a sensitive, large diameter sewer line. The 1800 m2 Waterloo barrier was driven to prevent hydrocarbon leachate from entering the Yukon River. Proposed driving of the sheet raised concerned as the sewer serviced downtown Whitehorse. Monitoring of the sewer during Resonant driving proved the ground vibrations to be imperceptible. Use of the Resonant Driver prevented all concern over ground borne vibration of the sewer and allowed the contractor to progress at conventional, high production while maintaining low cost to the owner.Subsequent projects continue to prove that Resonant driving of sheet piles achieves high production while eliminating ground vibration.IntroductionA complex environmental clean-up problem required a unique solution. A historic oil and fuel transfer station in Whitehorse, Yukon is located on the Yukon River. The facility has been in use since the Second World War and witnessed much careless activity. The sand and gravel site provided ease of transmission of hydrocarbon leachates directly into the Yukon River. Continued use of the site required a barrier wall be constructed to prevent hydrocarbon from leaching into the Yukon River. A short construction season and restrictive fisheries window made for a compressed schedule. Along the shoreline of the property and within the required clean up zone a large diameter sanitary sewer collector line was present that serviced the majority of downtown Whitehorse. The design called for a barrier wall to be constructed along the waterfront adjacent to the sewer with cofferdams constructed out into the Yukon River to recover contaminated riverbed soils. The coarse sands and gravels meant high hydraulic conductivity into any kind of excavation, including slurried or drilled shafts that may have been used to construct a low vibration shoring system. Conventional hammer or vibrator technology would result in high ground vibrations that risked damaging the sewer. The Resonant Driver method was selected for its ability to drive sheet piles with high production and zero ground borne vibrations."

Jan 1, 2014

By D. R. Dance

The Resonant, or as it has more commonly come to be known the 'Sonic' Pile Driver, dates back to the early 1960's, when prototypes were produced by Charlie Guild, of Providence, Rhode Island, and A1 Bodine of Los Angeles, California, these were later to be developed into the unit known as the BRD 1000. Based on this initial work, the Shell Oil Companies of Sonico and The Resonant Pile Corporation, produced and operated 30 of these BRD 1000 machines, which were used throughout the U.S.A. and Canada on a wide range of foundation projects. Subsequent to this, Raymond International and G K N, of England, operated units on programs; the G K N units being of slightly modified configuration. In 1973 Hawker Siddeley Canada Ltd., acquired the license for the Pile Driver and related systems with the intent of promoting the use of the machines to install support pilings on the Alyaska Pipeline Project, but this did not materialize due to problems with the oscillator. After radical redesign and field testing of the oscillator system the unit was employed on a number of test projects principally in Northern Canada and Alaska.

Jan 1, 1987

By R. W. Utley

Over one half billion tons of coal per year is scalped, classified, deslimed, drained and rinsed, dewatered and final sized on rotary, vibrating, shaking or stationary screens. The vibrating screen is the industry work horse and performs the bulk of the screening functions in the coal preparation plant. There are two major types of brute force mechanical vibrating screens used in coal preparation plants: (1) the two-bearing one-shaft inclined screen and (2) the four-bearing two-shaft horizontal screen. Both of these types are familiar to coal producers.

Jan 1, 1966

By Barry Silverman

As a significant mineral supplier, consumer of primary fuels, and producer of wastes and emissions to air, water, and land, the domestic copper industry through its investment and operating decisions influences the nation's economy and the environment. In turn, the copper industries' decisions are influenced by various factors: government energy and environmental policies, economic conditions, and technological considerations. The authors have developed a framework for assessing in an integrated manner the impact of these factors on the future investment and operating decisions made by copper firms. Specifically, this model is designed to capture the technology forcing nature of regulatory constraints, the differential situation of individual copper deposits and plant locations, and the price of factor inputs and conditions in the nation's economy. The capability to do this has only become real because of the decision of the U.S. Bureau of Mines to create Mineral Availability system1 or MAS. This system contains detailed but confidential information about each mine and mill in each of 35 mineral industries." Without MAS or a similar information system, the utilization of the methodology we offer would be impractical, but with. MAS it offers a unique technique of dealing with environmental-resources policy questions.

Jan 1, 1979

By Harry Parker

Resource and Reserve Audits Becoming Increasingly Common Types of Audits -Review of Methodology (‘Fatal Flaw’) -Due Diligence – (‘Sign Off’) -Endorsement – (‘QA-QC’) Suggested Standards in Red

Jan 1, 2003

By M Bond, R R. Hargreaves, G W. Booth

There are numerous causes of speculative mineral resource and reserve inflation. Traditionally, these are linked to issues of data accuracy or misinterpretation, the use of overly optimistic estimation parameters or assumptions, an absence of independent expert verification, or the simple pressure to increase company value, covert or otherwise. Owing to its subjective nature, classification of resources and reserves remains an opaque process. Of necessity, Competent Persons rely on personal heuristic interpretations, ideally underpinned by appropriate estimation and classification experience across commodity and deposit types. Whereas independent verification of individual resource and reserve statements remains impractical, publicly available data can be interrogated for potential category inflation, particularly when viewed with exploration expenditure statistics included in annual company reports. Abrupt changes in category tonnages and market capitalisation without concomitant expenditure can aid in outlier detection. Consequently, a comparison of common exploration and resource reporting parameters offers a basis for risk assessing classification robustness, over time. In this introductory study, an analysis of globally listed companies was undertaken over a multi-year period, examining base and precious metal projects in both preproduction and operational asset classes. From these, a series of exploratory decision tree trigger points were generated against which target companies were anonymously identified and risk-ranked.

May 24, 2023

By J. M. Ortiz, J. P. Bertini

"In mineral resource and ore reserve estimation, several sources of information are generally available, such as diamond drillholes, reversed-circulation drillholes, and blastholes, and originate from one or more sampling campaigns and are analyzed by one or more laboratories. In such a situation, the grade measurements may not have the same precision and one should distinguish between hard and imprecise data.This work aims at studying the impact of data imprecision in resource/reserve evaluation through two case studies on simulated deposits: a porphyry copper deposit conditioned to real exploration and production data, and a gold deposit simulated without any conditioning data. Several geostatistical techniques are used to estimate the grades of selective mining units from exploration samples, including kriging, cokriging, lognormal and indicator kriging. Two types of imprecision are examined— measurements with multiplicative errors and measurements defined as intervals. The results are compared to the simulated grades of the selective mining units from a statistical and economic viewpoint.The study concludes that imprecise measurements should never be discarded because they help to improve the estimates, and that simple methods such as kriging are as efficient as more sophisticated ones for resource/reserve assessment. Finally, a few indications on how to diagnose and model the data imprecision are given."

Jan 1, 2005

By D Hodson

Current classification of resources is entirely a subjective task. The various international reporting codes (such as the JORC Code) provide Competent Persons and practitioners with little specific guidance on the standard of work and levels of uncertainty required to classify resources into Measured, Indicated and Inferred. Furthermore, little guidance is given in the conversion of Resources to Reserves and the potential impacts on classification of uncertainties in the modifying factors. Working back from the intended use of the resource estimates, and in understanding the tolerance for uncertainty by the end user of such estimates, insights into the objective and requirements of classification can be determined. Following this approach a comprehensive set of (quantitative where possible) guidelines have been determined that will ensure resources meet the desired objective of each classification, and are consistent and comparable. The guidelines look at what is required for each step in the resource estimation process in order to ensure the final resource estimate meets the desired level of confidence. This approach provides a transparent, comprehensive, justifiable and largely objective method of classification. The implication of introducing such a guideline or approach is to highlight areas of a resource estimation that do not meet the requirements (ie drive the uncertainty beyond the objective) and then focus in on the risks that may flow on from that particular uncertainty, to mitigate or attempt to control those risks.

Jan 1, 2006

By Adam H. Zimmerman

Introduction Noranda, like similar businesses, is suffering the pain of previously unheard of currency relationships, a cost structure built in better days, and conditions of gross oversupply possible in almost any commodity. Indeed, it does seem like the worst of all possible worlds is out there before us. To understand a Canadian natural resource company, you must know how the country is organized. So far as natural resources are concerned, Canada is not Canada. Canada is 10 provinces and each own the resources situated therein. Thus, the conditions of extraction, exploitation, and operation are all set by the province, while the conditions of trade and currency are set by the Federal government. This means that what may be the rule in Newfoundland may not be the rule in Manitoba or British Columbia. The second thing is that the Canadian currency has been a satellite of the US dollar for a long time. This means that we hold the unenviable and unjustified position of being the country with the second strongest currency in the world. What this has meant to us is what it has meant to an American operator. Since 1980, a pound of copper fetches 214% more for a Chilean than it does for us and a pound of zinc 115% more for a Belgian. From an American point of view, Canada is favored because its dollar is valued at 25% to 30% less than the U.S. However, because of industrial indiscretions in years past, Canada has a locked in labor cost disadvantage that is very hard to cope with. Canada has a unique situation with its labor unions. Many of the unions are, or have been, internationals and therefore gained undue strength in early days. Canada has a third political party of socialist persuasion. It is entirely funded by dues from laor union members. Thus, we have a politicized workforce. And finally, we have a public service that has the right to strike. This had made the public service unions by far the strongest now in Canada. What this means to the mining industry is that there is somebody out there blazing the trail. The unrelenting power of these public service unions probably creates a climate more conducive to excessive wage settlements in industry than would otherwise be the case. Study, Work, and Pray So what do we do when times get tough? In simple terms, we study a lot, we work harder, and we pray a great deal. We study a lot in terms of learning hitherto unknown strengths and weaknesses of our products, processes, and operations. We work hard in the sense that we do everything possible to improve our productivity. And we pray a lot because, so far, anything else we have done has not been enough. Some years ago, Noranda recognized that its principal base and precious metal operations were diminishing. To provide for the future, we should branch out into other resource type operations. These might be countercyclical and also perhaps a little more permanent. For this reason, Noranda entered the potash, aluminum, and forest products businesses. This, of course, was a 'brilliant' strategy that was much applauded in its early days. We built an excellent potash mine, the smallest inte-

Jan 6, 1985

By A Calderon, J Harris, M Shi, D Viswanathan, C Ribeiro Duthie, P A. Kirsch

Mineral resource development activities impact the health and well-being of many people, from workers, to families and surrounding communities. In the current environment of corporate social responsibility life-of-mine planning considers that mining activities should be conducted in the best environmentally, socially and economically acceptable way for the entire life of the mine (ie from exploration to decommissioning and closure). In this context, the health impacts of mining extend throughout the life of the community from worker injury and chronic exposure to communicable and non-communicable causes of illness, through to family and community health and well-being. At the inaugural Life-of-Mine conference in July 2012, the authors proposed the life-of-mine in the life-of-community (LOMLOC) matrix as a framework for understanding issues at the interface between resource extraction operations and the surrounding environment.This paper reviews and compares health activities extracted from social and environmental reports published by selected major mining companies with American operations in Canada, Colombia and Brazil. These corporate approaches to public health management are mapped to the LOMLOC matrix to identify and compare trends and behaviour in corporate health investments. This analysis of how companies approach and prioritise health issues in the context of different regions, cultures and environmental drivers will serve as a resource for minerals industry managers, civil society and regulators regarding current health management approaches in this sector.CITATION:Ribeiro Duthie, C, Calderon, A, Viswanathan, D, ?Shi, M, Harris, J and Kirsch, P A, ?2014. Resource company investments in health – a life-of-mine / life-of-community perspective across America, in Proceedings Life-of-Mine 2014 , pp 349–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

The extractive industry has the potential to impact the health and well-being of workers, families and surrounding communities. In the current environment of social performance, project planning considers that activities should be conducted in the best environmentally, socially and economically acceptable way across the development cycle (i.e. from exploration ? post-closure). In this context, health impacts of mining can be mapped and extend over the Life of the Community and can encompass worker injury and disease, exposure to communicable and non-communicable diseases, and health outcomes specific to family and community health and well-being outside the fence. To contribute to an emerging field focused on Health and the Extractive Industry, this paper reviews and compares health activities extracted from social and environmental reports published by selected major mining, oil and gas companies with operations in Australia and Canada. The objective of this review is to map corporate approaches to public health management across our previously developed Life-of-Mine within Life-of-Community (LOMLOC) framework in order to identify and compare trends and behaviour in corporate health investments across the project cycle, as well as identify the level of prevention targeted by this investment activity (i.e. primary, secondary and tertiary prevention of detrimental health impact). With the extractive industry facing ongoing rapid growth worldwide, this paper provides preliminary comparative information about corporate health spending by some companies in Australia and Canada. This information serves as a resource for minerals industry managers, civil society and regulators regarding current health management approaches in this sector.

Aug 1, 2013