Search Documents

By Frederick B. Brien

For many years tin mining in Bolivia has been very important to the economy of the country. In recent years the tin content of the ore reserves has been steadily declining. An improvement in concentration efficiency is highly desirable in order to increase productivity from the present-low-grade mine ores and to allow retreatment of the many millions of tons of tailings from past operations, some of which equal the present ores in tin content. A number of investigators have been or at present are working on various phases or approaches to the problem. Gravity concentration is used in Bolivia today as it has been in the past to recover tin minerals from the mine ores. An objective of the work reported in this paper was to examine the possibility of treating present low-grade ores and sink-float tailings products, at a relatively coarse grind, in order to produce a higher grade feed material to the present gravity concentration plants. The possibility of using heavy liquids in cyclones to treat large tonnages with a minimum of outlay presented itself and is of particular interest since appropriate heavy liquids are available and with physical properties which lend themselves to simple recovery methods. Tests were carried out using a closed circuit laboratory cyclone assembly. It was desirable to determine the value of using the SG50 concept and Tromp curves for analyzing the cyclone concentration test results. The effects of entrained water on the behavior of ore particles in the cyclone were examined.

Jan 1, 1964

By CORA ROELOFS

In the USA, miners are at higher risk for work-related disorders that could precipitate an opioid prescription, injury-related opioid prescriptions, and opioid overdose. We aimed to support prevention of these outcomes with an “opioid hazard awareness” miner safety training module. In January and February 2020, the training module was embedded within required mining safety and health training for stone, sand, and gravel miners in Massachusetts (USA). Training impact and reception were assessed with a pre- and post-training survey of trainee characteristics, training content knowledge, and attitudes. Over 800 miners were trained and over 600 responded to surveys. We found statistically significant improvements in opioid risk factor knowledge and knowledge of resources to help a coworker. Nonstigmatizing attitudes were high both at baseline and following the training. The training was perceived as relevant and useful by trainees. Improving opioid hazard awareness in high-risk worker populations has potential to reduce opioid dependence and downstream impacts including overdose death. Employer injury-prevention efforts should be reinforced while worker health and safety training enhances awareness of opioid-related harms and prevention strategies for miners and other high-risk worker populations.

Nov 19, 2021

By CORA ROELOFS

While the COVID-19 pandemic has dominated the headlines, another epidemic in the United States has continued apace — the opioid epidemic. Half a million opioid overdose deaths have occurred in the United States since 1999, when the opioid epidemic began. The causes of the epidemic include the rise in prescriptions for opioid pain medications, including for work-related pain. Miners and other occupations identified as physically demanding and at higher injury risk have been found to be at increased risk for opioid overdose [1]. However, awareness of the risk factors that might lead to opioid use, the potential hazards associated with their use, and resources to prevent addiction and death can allow miners to make choices that can reduce these risks.

By S. R. Dindarloo

"Truck-shovel systems are the dominant material loading and haulage machinery in open pit mining operations. Optimal selection, sizing, and allocation of this capital intensive equipment is highly desirable for both achieving production targets and improving the mine’s economics. In this study, discrete event simulation technique was applied for modeling material transportation in Golegohar open pit iron ore mine in Iran. Direct observation of the material loading and haulage for duration of three months resulted in statistical modeling of the operation in the form of probability distribution functions. These probability models were used as the inputs of a stochastic simulation model constructed in GPSS/H simulation language. The model was validated through comparison with the actual operation and was used to test different what-if scenarios and sensitivity analysis of the current system. Some modifications in the number of trucks, shovels, and dispatching strategies were proposed. Simulation resulted in considerable improvements in the mine’s production and economics.INTRODUCTION There are three different mechanisms of discrete, continues, and hybrid material transportation in open mines, including but not limited to: i) in-pit crusher and conveyor belts (hybrid), ii) slurry piping (continues) and iii) truck-shovel system (discrete). Although, each mechanism has its advantages, the truck-shovel system is the dominant method of material loading and handling in open pit mines owing to its high production rate, excellent flexibility, relatively low operating and capital costs, and good maintainability. General objectives of optimal equipment selection include: i) meeting the long and short term requirements of production rates, ii) human & equipment safety, iii) environmental protection, and iv) economic operations (Figure 1).The two most important decision factors on a truck-shovel system selection and sizing are the equipment geometry and size. Geometry (equipment width, weight, turning radius, swing angle, etc.) is mostly controlled by mine’s designs and layouts, as well, as operational constraints. After selection of a favorable geometry based on the constraints; the next step is to select the equipment manufacturer. Once the geometry and manufacturers are selected; the next step is to decide on models (e.g. Bucket size) and required number of each unit"

Jan 1, 2015

By S. R. Dindarloo

"Truck-shovel systems are the dominant material loading and haulage machinery in open pit mining operations. Optimal selection, sizing, and allocation of this capital intensive equipment is highly desirable for both achieving production targets and improving the mine’s economics. In this study, discrete event simulation technique was applied for modeling material transportation in Golegohar open pit iron ore mine in Iran. Direct observation of the material loading and haulage for duration of three months resulted in statistical modeling of the operation in the form of probability distribution functions. These probability models were used as the inputs of a stochastic simulation model constructed in GPSS/H simulation language. The model was validated through comparison with the actual operation and was used to test different what-if scenarios and sensitivity analysis of the current system. Some modifications in the number of trucks, shovels, and dispatching strategies were proposed. Simulation resulted in considerable improvements in the mine’s production and economics.INTRODUCTION There are three different mechanisms of discrete, continues, and hybrid material transportation in open mines, including but not limited to: i) in-pit crusher and conveyor belts (hybrid), ii) slurry piping (continues) and iii) truck-shovel system (discrete). Although, each mechanism has its advantages, the truck-shovel system is the dominant method of material loading and handling in open pit mines owing to its high production rate, excellent flexibility, relatively low operating and capital costs, and good maintainability. General objectives of optimal equipment selection include: i) meeting the long and short term requirements of production rates, ii) human & equipment safety, iii) environmental protection, and iv) economic operations (Figure 1).The two most important decision factors on a truck-shovel system selection and sizing are the equipment geometry and size. Geometry (equipment width, weight, turning radius, swing angle, etc.) is mostly controlled by mine’s designs and layouts, as well, as operational constraints. After selection of a favorable geometry based on the constraints; the next step is to select the equipment manufacturer. Once the geometry and manufacturers are selected; the next step is to decide on models (e.g. Bucket size) and required number of each unit"

Jan 1, 2015

By Jorge Beim

Helical Piles are increasingly being used to support and rehabilitate structures subjected to compressive axial loads. Traditionally, empirical correlations between installation torque and load capacity of helical screw piles are used as the field quality control. Load tests, however, are always recommended to validate the installation process and design methodology. This paper describes a test program performed on helical piles installed at the National Geotechnical Experimentation Site of the University of Massachusetts - Amherst campus (UMass-Amherst), well known for its deep varved clay deposit. Seven of these piles were submitted to Dynamic Load Tests using the Pile Driving Analyzer® (PDA), and also to Static Load Tests. Good agreements were obtained between the results of the dynamic and static load tests, encouraging the use of the former testing method as a viable alternative to the latter for determining the compressive load capacity of helical piles installed in cohesive soils. The results of the load tests were also compared to the predictions based on torque correlations, resulting in correlation coefficients which were higher than the ones traditionally used.

Jan 1, 2012

By Wenhua Wan, Jan M. Mutmansky

Many concerns have been expressed worldwide regarding the use of diesel equipment in underground mines due to the potential health risks associated with diesel particulate matter (DPM). In assessing the risk to the health of miners and designing control strategies for DPM, it is important to know the concentration of DPM in the working areas of a mine. In some mines, significant stratification occurs due to the characteristics of the diesel exhaust, affecting exposure and the ability to measure DPM concentrations accurately. This study outlines some of the concentration profile data obtained during sampling at three mines where diesels were employed. Mine #1 (a gold mine) employed large openings in which a diesel-powered roof bolter was used. Mines #2 and #3 are both room-and-pillar operations with varying conditions. Mine #2 is an experimental mine where two stationary diesels were utilized for sampling purposes, while Mine #3 is a traditional evaporite operation using two mobile diesel vehicles for section haulage. These field studies indicated that some level of stratification occurred in all the mines, but the stratification was not as pronounced in the case of Mine #2 due to the complex pattern of exhaust emissions generated by the vehicles. The stratification seemed to depend on the distance from the vehicle, the mine air velocity, whether the vehicles were moving or stationary, and whether the exhaust was diluted by equipment design features. The concentration of DPM was generally higher at samplers located near the roof and lower at samplers located near the floor. However, this was not found in all cases. This paper provides conclusions on how knowledge of stratification patterns can be utilized in sampling and control of DPM in mine atmospheres.

Jan 1, 1997

By P. H. Morris

To achieve the full potential of sub-aerial co-disposal the properties of the co-disposed wastes must be known and understood. A description is given of the morphology and properties of waste deposits that were formed during 19 field trials of sub-aerial co-disposal at the dual Goonyella-Riverside mine in Queensland and at Hunter Valley No.1 and Warkworth mines in New South Wales

Jun 19, 1905

By John D. Morton, J. H. LaVerne Palmer, Douglas J. Belshaw

An extensive programme of ground instrumentation and observation was carried out for the West Duff in Outfall Sewer tunnel project prior to and during construction, to establish the performance characteristics of the rock through which the tunnel and appurtenant openings were dug and to examine the nature of the lining-to-ground interaction. The existence of high horizontal residual ground stresses was confirmed, and values established by overcoring. Rock deformations and stress changes were monitored during tunnelling. Permanent stress and strain monitoring devices were set into the final lining and these are continuing to operate. INTRODUCTION The site is located on the north shore of Lake Ontario at Pickering, some 20 miles (32 kilometres) east of Toronto, Canada where a variable thickness of glacial or interglacial sediments overlies bituminous shale bedrock of. the Collingwood Formation which is lower Ordovician age. Approximately 50 feet (15 metres) of glacial cover exists at the shaft, though this thins abruptly at the regressing cliffed shoreline such that several small areas of exposed bedrock exist in the lakebed. The general location, overall geological section and detailed site plan and profile are illustrated in Figs.1,2 and 3 respectively. General properties of the rock as established during an extensive test drilling and site investigation programme are listed in Table 1, while stress determination by USER overcoring stress meter device are given in Table ll. These data formed the basis of analyses which were done to examine the intended outfall design, and to detail the construction procedure and the observational instrumentation programme.

Jan 1, 1979

By L. Filip

The roast-leach-electrowinning (RLE) process for zinc was modified to treat two typical complex concentrates containing zinc, lead, copper, gold and silver. Laboratory testwork results indicated that the optimum roasting temperature ranged from 700 to 800°C, in order to produce acceptable residual sulfur levels. The calcined concentrate was subjected to a three-stage leach sequence. The resulting leach solution was purified by hematitic precipitation and directed to the recovery of copper and zinc by solvent extraction and electrolysis. Alkaline smelting and subsequent electrolytic purification recovered the lead and precious metals from the leach residue. A flowsheet was developed based on the laboratory testwork results, and demonstrated in a large-scale pilot plant. The recoveries produced during the pilot plant operation ranged from 90 to 92% for zinc and copper, 85% for lead and 90% for gold and silver, respectively.

Jan 1, 1999

By Lynn Alcorn, Jeffrey Shawn Peterson

Data collected by the Mine Safety and Health Administration (MSHA) has shown that roof bolting machine (RBM) operators are the second most likely type of underground mining machine operator to be are over exposed to noise, per the MSHA Permissible Exposure Limit. In response to this, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has initiated a project to develop engineering noise controls for roof bolting machines. Key to this research is an evaluation of the duty cycle of a typical roof bolting machine operation and this paper presents the results of such an exercise for data collected at two cooperating coalmines. The evaluation entails a time motion study of an operators' shift, logging each activity for time (e.g., tramming the machine, drilling holes, installing the roof bolt, etc.) and the noise levels associated with each task with a Larson Davis Spark 705+ dosimeter. NIOSH post processed the data to determine which tasks the operator devotes the most time to and the noise dosage accumulated during those tasks. These results provide insight into which portion of the operators' duty cycle is the most prominent contributor to noise exposure and thus, where research activities for the development of engineering noise controls should be focused. It was determined that the task of drilling holes is the most significant source of the operators' noise exposure and project research has focused on engineering noise controls to reduce the noise emissions generated during the drilling portion of the machine duty cycle.

A research and testing facility has been developed at Simtars to allow the spontaneous combustion testing of coal on a large scale. In this adiabatic reactor, the coal particle sizing is closer to that which could be found in the goaf and therefore the reaction is more likely to simulate the underground situation. This allows aspects of the spontaneous combustion process and methods for detecting a heating to be investigated which cannot be done in an operational mine. Up to 18 tonnes of run of mine or crushed coal is loaded into the reactor and allowed to self-heat while the temperature and gas profiles within the coal pile are monitored. The gases evolved from the coal are analysed using a fixed gas monitor system and gas chromatography to determine which of the common mine fire indicators and ratios can be used to predict the onset and progress of coal heatings. Benchmarking of the inherent propensity of a coal to spontaneously combust at both the large- and laboratory-scale is also possible by comparing the sample against previously tested samples. It has been found that the coal particle size affects both the time it takes for the coal to react and the location of the developing heating. The heatings generate approximately one metre from the inlet but in the crushed coal case do not progress to an advanced heating stage until the æhot spotÆ migrates towards the coal surface where there is an increased oxygen supply. Physical properties such as the compressive strength of the coal also affect the heating size and the time it takes for a heating to develop. Higher strength coals appear to oxidise more slowly and therefore take longer to self-heat as oxidation of the coal is the heat-generating step in the spontaneous combustion process. The best indicators of the state of the heating were found to be CO make and GrahamÆs ratio which are independent of air flow. Investigation of a potential spontaneous combustion should begin as soon as the CO make or GrahamÆs ratio exceed the background levels. The results from the tests undertaken on a number of Queensland and NSW coals are reported here together with the implications for the mining industry.

Jan 1, 2005

By N. Pearson, F. Calizaya

PT Freeport's mine in Irian Jaya, Indonesia uses a number of 500 m (1,640 ft) long vertical ore passes to transfer ore from the open pit to the mill. The current tonnages moved are in the order of 125 kt/d (138,000 stpd) and this will be increasing to 240 kt/d (265,000 stpd). This amount of falling rock generates high pres¬sures in the ore bins, when ore feed is terminated the pressure is no longer constrained resulting in back blasting of materials and air the ore passes. Three methods were tested to try and eliminate or reduce this problem; recirculation the entrained air, widening of the orepasses and relieving the pressure the back blast. The final method proved to be the most effective in the short term. As a long term so¬lution the orepasses are currently undergoing widening.

Jan 1, 2000

PT Freeport's Mine in Irian Jaya, Indonesia uses a number of 500m long vertical ore passes to transfer ore from the open pit to the mill. The current tonnages moved are in the order of 125 ktpd and this will be increasing to 240 ktpd. This amount of falling rock generates high pressures in the ore bins, when ore feed is terminated the pressure is no longer constrained resulting in back blasting of materials and air up the ore passes. Three methods were tested to try and eliminate or reduce this problem; recirculation of the entrained air, widening of the orepasses and relieving the pressure of the back blast. The final method proved to be the most effective in the short term. As a long term solution the orepasses are currently undergoing widening.

Jan 1, 1998

By V. Grujic, M. Grujic, D. Salatic

"Two areas are involved in the research work of the comminution process (crushing and grinding). The first one involves the changes of the size class distribution values that are definded by the differential equations in the function of the ore property and working conditions. The second area involves the comminution of the different levels in order to optimize the working parameters and to decrease the operational costs in the grinding process.We have studied, in detail, the possibility of functioning the crusher at the maximal loading, over 4500 kN, ball mills with diameters larger than 5.0 m and semiautogenous mills with diameters larger than 10.0 m.Using the computers, we have achieved the maximal loading range of the crusher, over Fc ? 4500 kN in the crushing process. In the grinding process, using the adequate differential equations in the automation process, we have established the correlation between the pulp mass capacity in the mill, pulp dencity, ore fineness in the pulp and recirculating ore charge.With the appopriate text, equations and graphs, this paper shows the results of our several years research work in the laboratory and in the ore comminution plant of Majdanpek Copper Mine."

Jan 1, 2003

By T. J. Close

On September 10, 1991, Secretary of the Department of Interior Manuel Lujan deleted the Silver Peak Range North Wilderness Study Area from the list of U.S. Bureau of Land Management lands in Nevada to be considered for wilderness designation. This decision was based in part on the U.S. Bureau of Mines mineral investigation of the wilderness study area which found that it has indications of precious metals resources. The following is a summary of the results of that mineral investigation. The study area lies between the Silver Peak and Dyer mining districts of west-central Nevada. The Silver Peak mining district, to the east, has a long mining history dating back to 1907 when precious-metals-bearing veins were discovered. The major producer in the Silver Peak district was Sunshine Mining Company's Sixteen-to-One silver mine. During the Bureau's study the Sixteen-to-One mine was operating; it has since been idled due to low silver prices. Precious metals-bearing veins were discovered in the Dyer district, to the west of the study area, in the 1860's. Mineral activity in Dyer district consisted mainly of prospecting. The Silver Peak study area itself has no mining history and contains only a few mining claims, but the Bureau examined 13 mineralized sites, most previously unknown and unclaimed. These sites are along two zones that cross the study area from the Silver Peak to the Dyer mining district. The two zones transect a volcanic center of fractured and altered rocks that contain epithermal veins of quartz, calcite, and jasperoid with gold, silver, and base metals. At the surface these veins are poorly defined and poorly mineralized. The more than forty veins examined in the study area are as thick as 17 feet and as long as 1,000 feet. Samples from surface exposures of these veins contained as much as 0.02 ounce per ton gold, 2.1 ounces per ton silver, 1.0 percent copper, 2.6 percent lead, and 0.4 percent zinc. Analyses of the Bureau data disclosed no vein large enough or of high enough grade to be classified a mineral resource. However, most do have indications of silver-and gold-bearing resources at depth. Subsurface exploration had to be done on the vein at the Sixteen-to-One mine to outline reserves (a vein averaging about 22 feet thick and containing 6-to 7-ounces per ton silver); the same is true of veins in the Silver Peak Range North Wilderness Study Area.

Jan 1, 1993

By T. J. Close

The Silver Peak Range North Wilderness Study Area was deleted from the list of US Bureau of Land Management lands in Nevada to be considered for wilderness designation. This decision was based in part on the US Bureau of Mines mineral investigation of the wilderness study area which found indications of precious- and base-metal-resources. The study area lies between the Silver Peak and Dyer mining districts of west-central Nevada. The Bureau examined 13 mineralized sites, most of which were previously unknown and unclaimed. These sites are along two zones that cross the study area from the Silver Peak mining district to the Dyer mining district. The two zones transect a volcanic center of fractured and altered rocks that contain epithermal veins of quartz and calcite with gold, silver, and base-metals. At the surface, these veins are poorly defined. Exposures of the more than forty veins examined were as thick as 17 ft and as long as 1000 ft. Samples from these veins contained significant amounts of precious- and base-metals-as much as 0.02 oz per ton gold, 2.1 oz per ton silver, 1.0% copper, 2.6% lead and 0.4 % zinc. No vein large enough or of high enough grade to be classified a mineral resource was disclosed by the sample data. However, most do have indications of precious- and base-metal-resources at depth. Subsurface exploration of some of the veins is recommended.

Jan 1, 1995

By T. F. Tomb

on' January 6, ,1992, the Mine Safety and Health Administration (MSHA) issued an Advanced Notice of Proposed Rule Making (ANPRM) for diesel particulate (DP). The ANPRM identified five areas where the Agency was seeking additional information to assist in the rule making process. These areas were exposure 'limits, risk assessment, consideration of other information, sampling and monitoring methods, and feasibility. The period for submitting information relative to the ANPRM closed July 10, 1992. Prior to issuance of the ANPRM, the agency was involved in conducting studies to evaluate sampling and control technologies and to gather information with respect to occupational exposures to diesel particulate in underground mining operations employing diesel-powered equipment. Since issuance of the notice, additional studies have been conducted to provide supplementary information in these specific areas. Results of these additional studies indicate that average DP levels in coal mines not using aftertreatment range from 0.9 to 2.1 mg/m3. Aftertreatment devices can reduce these levels by approximately 50 to 90 percent. Studies conducted in metal and nonmetal mines showed average DP levels ranging from 0.3 to 1.6 mg/m3.

Jan 1, 1994

By Ken Schei, Martin Reed, Samuel Bowser, John Wright

From October 18 through October 21, 2001, United States Antarctic Program blasters opened ten access holes for research divers in 11-ft. thick sea ice at Explorers Cove, McMurdo Sound, Antarctica. During this project, a blasting seismograph with a hydrophone accessory was used to monitor the underwater shock waves associated with the blasting technique. Shock wave values averaged 42.3 psi for initial (cratering) shots and 5.9 for subsequent clearing shots, indicating that the ice absorbs most of the shock wave. The results also provide data for refining safety protocols for divers and for the protection of marine biota.

Jan 1, 2003

By Porfirio Pinto Linares

El presente texto señala la paragénesis y zoneamiento en el yacimiento de Morococha. Dicho distrito está ubicado al este de Lima, cuyos principales productos minerales son el zinc, cobre, plata y plomo. Para dicho estudio geológico se empleó los valores de ensayos para el cobre, plata y zinc principalmente; en algunos casos, los valores para el plomo; de las vetas estudiadas. En el estudio de la paragénesis no se ha hecho un estudio completo al microscopio de la secuencia de los minerales de la veta. Se han aprovechado únicamente, las mejores exposiciones en el subsuelo que ofrecen evidencias excelentes para deducir las características principales de la paragénesis.

Mar 1, 1965