Search Documents

By Liu Cheng-si

Basing on a brief assessment of the conventional theory of ventilating air distribution, its methods of calculation and practical application, this paper makes an approach to the controllability of different aircourses of a ventilation network and further points out that it is possible for the positions of control to extent into the natural distribution subnetwork of the ventilation network, which was been long considered as a restricted zone. This important discovery makes the regulation of the ventilation system more flexible and diversified, thus attaining quantitative distribution of ventilating air as well as a cost benefit. Because it has been impossible to solve the problem mentioned above by conventional theory and its relevant methods of calculation, the author, based on applying graph theory on the structure, characteristics, and requirements of controllability of the ventilation network, presents a new controllable subgraph concept and the means for determining the rational quantity for control devices of the ventilation network. The solution of all the control alternatives and methods of obtaining all the parameters for the solution of various alternatives have been derived. The economic benefit and the optional positions of the control devices have also been approached. Specific calculation examples are a1 so included in this paper. Along with the conventional theory and its methods, it can be seen that the new theory presented makes a great change in the control aspects of the ventilation network, with the number of possible alternatives increasing in an astonishing manner. Among the alternatives, some may be safer, more economical or technologically superior than those obtained from conventional theory. Thus, the new theory may provide an immense improvement in the choice of a ventilation system.

Jan 1, 1987

By Masaki Kitazume

Deep mixing method, in-situ admixture stabilization technique, has been developed and adopted for on land and marine construction works in Japan. The geotechnical design procedure of the method has been standardized in Ministry of Land, Infrastructure and Transport Government of Japan for port and harbor facilities, which includes the block type and wall type improved grounds for foundation stability, settlement reduction purpose. This procedure is based on the allowable stress concept, in which the induced stresses within the improved ground are confirmed to be lower than the allowable strength in the internal stability calculation. This procedure has been cited by several organizations to establish their standards. The Ministry has a plan to introduce a reliability based design for marine construction works in 2006, in which the design procedure on DM improved ground will also be modified to the reliability based. In the new design procedure, the average and variation of soil parameters and external loads are incorporated by partial safety factors to investigate the stability of improved ground. According to the plan, the author has been studied the design procedure and the magnitude of partial safety factors, and has established a preliminary draft of the standard. This draft will be brushed up through comparing the current design procedure. In this article, the design concept and design procedure of the method are briefly described.

Jan 1, 2004

By Antonio Nieto, Jesus Castillo

Research and Development (R&D) departments in the mining sector are essential for creating new solutions on productivity, safety, and sustainability. Nevertheless, the selection of R&D projects is complex, often influenced by subjective judgments and uncertainties. This paper explores the application of the Multicriteria Decision Analysis (MCDA) as a structured approach to evaluate and prioritize innovation projects based on various criteria such as safety, cost, environmental impact, and social acceptability. By assigning weights and quantifying criteria, MCDA enhances decision-making transparency and objectivity. This study aims to show a method that facilitates strategic thinking, resource optimization, and stakeholder engagement, ensuring that selected innovations align with the company’s long-term objectives and commitment to responsible mining practices.

Feb 1, 2025

By D. M. Milne, P. J. Lunder, R. C. Pakalnis

During the mining of an open stope, deformation of the hanging-wall and the potential for dilution generally increase with the size of the exposed hanging-wall. Excluding discrete structures that may delineate unstable blocks, the mechanisms that drive hanging-wall deformation and possible dilution comprise several factors which can include elastic, plastic and discontinuum deformation. These stages of deformation are not mutually exclusive and at any point during mining all three of these mechanisms may be acting on the hanging-wall rock mass. Computer modelling techniques are available to analyse the three stages of deformation, but the difficulty lies in trying to obtain realistic rock mass properties for input and in determining when each stage of deformation is acting. Instrumentation data can be used to predict the effect of continued mining. However, it is often difficult to calibrate numerical models against field data owing to the large number of input parameters required. An empirical approach is recommended that uses two new parameters, the radius factor and the effective radius factor. A method is proposed for predicting the effect of continued mining from existing deformation and dilution data for a given hanging-wall

Apr 1, 1996

By Jeffrey A. Schaefer

The Olmsted Locks and Dam project is located on the Ohio River approximately 16.5 miles upstream of its confluence with the Mississippi River. It consists of twin 1200 ft. locks with floating and fixed approach walls, five 110 ft. wide tainter gate bays, a 1400 ft. wide navigable pass boat operated wicket gate section, and a 400-ft. section of fixed weir (Fig. 1). The project will have a total cost over 1.0 billion dollars, and as such is one of the largest civil works project underway in the Corps of Engineers.

Jan 1, 2001

By S J Riley

The cover (cap) over the tailings pit at Nabarlek uranium mine must be structurally stable as it will act as a barrier to radon gas emission and have to contain other long-lived radionuclides. Structural stability is primarily an issue of erosional stability in the context of a design life of thousands of years. The primary agent of erosion is fluvial, dominated by rainwash, overland flow, filling and gullying in the local area. Other agents of erosion are of less concern although biogenic agents of erosion (eg termites and windthrow) may enhance fluvial activity. Several methods may be used to assess erosional stability. They fall into two main categories, namely erosion modelling and geomorphic modelling. The former is illustrated by the Universal Soil Loss Equation in which parameters describing aspects of the geotechnical and hydrological properties of the rehabilitated surface are used as input for the modelling of erosion rates. The latter is illustrated by estimates of gully and valley erosion using empirical models. Estimates of the erosion rates and stability of the Nabarlek cover are presented. The two main techniques are complementary and it is argued that rehabilitation design must make use of both approaches when estimating erosion and geomorphic stability. More recent developments in geomorphic modelling using numerical techniques incorporate both approaches.

Jan 1, 1994

By T. E. Wakefield

Over several decades in Southern Africa the advance rates when sinking vertical shafts have declined significantly. The upside has been a substantial improvement in shaft bottom conditions and a commensurately improved safety performance, with an increasing number of shafts being sunk without fatalities and disabling injuries. This paper briefly reviews historical sinking rates and matches changed sinking productivity to the introduction of new sinking methods that have been adopted to eliminate/mitigate safety risks. Meeting the challenge of returning to historical advance rates whilst progressing in the quest for zero harm by utilizing three dimensional animated computer modelling is described. Making use of commercial modelling software makes it easier to evaluate different methods, sequencing, in shaft barrel ergonomics, and stage and shaft bottom layouts before procuring project plant and equipment. Benefits accrue not only in better communicating methods and configurations for detailed planning and design, but also during crew training. The traditional engineering ?as-built? drawing practice has been extended to the concept of an ?as executed? sinking model which seeks to capture operational experience and learning for future best practice. The paper concludes with some of the organizational culture challenges being overcome as this non traditional approach to shaft sinking optimization is being introduced.

Jan 1, 2009

By W B. Edgar, S C. Dominy

High-nugget effect vein-gold systems are generally considered to be one of the most challenging of deposit types to evaluate and exploit. To potential investors and mining companies, they are viewed as high risk because of the associated uncertainties in the grade estimate and general paucity of Ore Reserves at production start-up. However, despite the well-known risks, these deposits often have a grade upside that makes them potentially attractive. The reporting of resource grade is of importance and perhaps even more so is the reporting of the associated uncertainty attached to the grade estimate. The use of the grade estimate supported by a grade range is recommended to achieve more complete and useful disclosure. The definition of the grade range can be somewhat subjective, ranging from opinion based estimates through to data-based estimates and geostatistical conditional simulation. Whichever method used, the over-riding issue must be the provision of enough data of appropriate quality and full disclosure to the public of relevant uncertainties.CITATION:Dominy, S C and Edgar, W B, 2012. Approaches to reporting grade uncertainty in high-nugget gold vein projects, in Proceedings Project Evaluation 2012 , pp 95-108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By K G. van den Boogaart, U Mueller

"An accurate prediction of benefit for some types of ore may require not just the ore grade, but a whole compositional characterisation of the estimates; that is, its full mineral composition including waste composition and nuisance elements. An example is Nickel laterite ores, where Ni/Co content must be complemented by estimates of many other elements, as these might have a notable impact on ore processing.Estimates are often obtained with (co-)kriging or co-simulation; however, geostatistics applied to compositional data may yield spurious and inconsistent results because of the constant sum constraint. The log-ratio approach avoids such problems. It proposes a three-step procedure: data are mapped to a set of log ratios of components; for example, the additive log-ratio transformation (alr) transformed scores are modelled with an appropriate fully multivariate geostatistical toolbox; for example, direct/cross-semivariograms and co-kriging or co-simulation results are back-transformed to the original units.Some practical aspects may make the application of this technique difficult: the assumption of Gaussianity and the high dimensionality of the compositions combined with the need for using multivariate methods. This contribution compares several ways of treating compositional data (combining normal score transformation, log-ratio transformations, and minimum/maximum autocorrelation factor (MAF) decomposition) with respect to their ability to generate sensible simulations. The various approaches considered are illustrated with a Nickel laterite data set for which ten variables are available. Both theoretical considerations and illustration results suggest that the best combination is (log)ratio-normal score transform-MAF, in this order. The factors so obtained are closer to Gaussian, approximately spatially decorrelated and can be simulated independently. Simulations can later be recombined to alr-simulations, which in turn may be converted back to point compositions. The resulting simulated compositions are compared with a full Gaussian co-simulation of the raw data. The log-ratio methods show reasonable to good reproduction of mean values, and distribution of the data set and by construction satisfy the total sum constraint, in contrast to the simulations based on raw data for which the total sums fluctuate strongly.CITATION:Mueller, U, Tolosana-Delgado, R and van den Boogaart, K G, 2014. Approaches to the simulation of compositional data – a nickel-laterite comparative case study, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 61–72 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By Michael W. Neill, O&apos

The engineering profession generally does not accept vibro-driven piles as bearing piles unless their capacities can be verified by restriking with an impact hammer, which significantly reduces the economic benefits of vibratory driving. In part, the concern for capacity development in piles driven by vibration arises out of observations that vibro-driven piles do not develop capacities equivalent to those driven by impact (e. g., Mosher, 1987). Nonetheless, if capacities are predictable, vibratory installation may be more cost effective than installation by impact, due to savings in time of installation, even if capacities are lower than those of impact-driven piles. Throughout the past few decades, a number of attempts have been made to develop capacity prediction methods for vibro-driven piles, mostly along the same lines as methods for impact-driven piles. That is, (1) totally empirical formulae, (2) power balance / power transfer formulae, and (3) "time domain-nonlinear" (TDN) computational procedures such as the wave equation. Some of the formulae have been based partly on field experience, but the majority have been developed from simple theoretical models with parameters evaluated from laboratory studies. Neither these formulae nor the TDN solutions have been systematically checked (or modified) by recording appropriate field data over a variety of site

Jan 1, 1989

Underground mining and particularly dipping narrow tabular orebodies are difficult to mechanize appropriately, given the low gold price and other external factors. Particularly in the deep level mines in South Africa, there is little choice left but to mechanize if the industry is to remain competitive and a significant global player. This paper presents a design philosophy for appropriate mechanization intended to generate solutions that can be implemented using the people currently employed in South Africa mines. The design philosophy is based on the ability of high-pressure water (hydropower technology) to deliver enhanced performance to users and on simplicity in the eyes of the user. Four examples of systems and equipment are described to illustrate the approach to Appropriate Mechanization. These include: • The Development End System, • The Monorail Raise Climber, • Automatic Pump Control Valves, and • The Energy Recovery Pump. The equipment is presented with the following critical issues foremost in mind: Safety, Working Environment, Performance, Cost effectiveness and Implementation. Although the appropriate mechanization approach is described in the context of the South African underground mining industry, much of the Appropriate Mechanization equipment has worldwide applications. Key Words: Hydropower, Mechanization, Tunnel Development, Raise Development, Monorail, Raise Climber, Pump Control Valve, and Energy Recovery

Sep 1, 2001

By M. M. Hajdasinki

A project's rates of return (RORs)1, be it the internal rates return (IRRs) or one of the many IRR surrogates, frequently needs to be approximated. The success and efficiency an ROR- approximation procedure depend on the quality the approximation-initiating parameters, such as bounds or seed values (guesses). The existing approximation procedures commonly use bounds and guesses suggested by intuition rather than supported by mathematical considerations. This paper presents three mathematically founded ROR-bounding and eleven ROR-guessing approaches and examines their suitability by using examples of typical project cash-flowpatterns (CFPs). The calculated bounds and guesses not only improve the approximation efficiency, but also allow the process of the ROR discovery to be automated, thereby making it more convenient and reliable.

Jan 1, 1999

By R. Laplante, P. Radziszewski, P. De Ciccio

"Predicting the effect of wear can lead to improved control strategies that can possibly minimize the risk of catastrophic failure due to wear while maximizing useable life. In the field of geological exploration, diamond drill rod wear illustrates just such a case. Wear conditions vary with geological formations and compositions. The objective of this paper is to determine a general relationship, based in theory and practice, that will approximate drill rod wear and therefore predict remaining drill rod life in the context of Canadian, Australian and South American drilling campaigns. Simulation results allow the definition of simple graphical tools that permit the estimation of the potential drill depth remaining on a given drill rod string. IntroductionWear, in many industrial processes, is an undesired phenomenon for which enormous efforts are made to control, if not eliminate. However, wear, in many other cases, is an intrinsic phenomenon of the given process. In such cases, predicting the effect of wear can lead to improved control strategies that can possibly minimize the risk of catastrophic failure due to wear while maximizing useable life. In the field of geological exploration, diamond drill rod wear illustrates just such a case where abrasive conditions vary with geological formations and compositions.A number of studies have been published on drill rod wear especially with regards to the petroleum industry over the last thirty years (Lewis, 1968; Rollins, 1968; Smith, 1978; White 1978; Rowe and Wilson, 1981; Cheng, 1982; Eustes, 1986; Dudman et al., 1989; Besaisow et al., 1990). Of these, most studies covered management techniques (Rollins, 1968; Smith, 1978; White, 1978; Rowe and Wilson, 1981; Besaisow et al., 1990) and some described case histories (Cheng, 1982; Eustes, 1986; Dudman et al., 1989). However, little (Lewis, 1968) was presented that could aid in predicting wear in the particular case of diamond drilling in the metal mining industry.The objective of this paper is to determine a general relationship, based in theory and practice, that will approximate diamond drill rod wear and therefore predict remaining drill rod life in the context of Canadian, Australian and South American diamond drilling campaigns."

Jan 1, 2002

Approximation of Surface Area of Fines in Blast Induced Fragmentation The surface area of fragmentation, especially in the finer size fractions, is a useful property to characterise the mechanisms of rock breakage. In the past, researchers have made assumptions with regard to the shape of fragments in order to estimate surface area, such as that all fragments are the same shape or all fragments are spheres. Often these assumptions were developed with inappropriate measures and returned considerable variability and error for the calculation of surface area. This paper reports a model to estimate fragmentation surface area from sieve sized raw data and a density measurement, with experimental validation down to a size fraction of -45 + 38 ?m in a range of rock types. After characterisation of particle shape, a range of fragment shapes was found to be in each size fraction. Nevertheless, in the ?2 sieve series the average fragment mass, volume and the size fraction standard deviations could be predicted reasonably accurately. Ellipsoid geometry was used to describe particle shape. Using these parameters and the number of fragments (also predicted) in each sieve size the individual surface area of each fragment was simulated.

Sep 13, 2010

By A. Kenneth Schellinger

IF the ball mill is considered only from an energy standpoint, it can be thought of as a converter of kinetic energy into heat energy and surface energy. The law of the conservation of energy must apply to the ball mill as it does to any machine or process in nature. The heat energy output of the ball mill is apparent to any casual observer of the operating mill since the outflow pulp will be appreciably warmer than the inflow water and rock. The rock in the ball mill is crushed by shearing of its ionic bonding caused by some impact-induced stresses beyond the elastic limit. As the bonds holding the mineral crystal lattices together are ruptured, new surface area is created on each unit of which a definite number of unsaturated bonds exist. Such unsaturated energy of bonding may be termed the "surface energy," and is a potential energy figure. This created energy was withdrawn from the ball mill system and represents an absorption, or disappearance of heat. To reduce the size of the rock, surface area must be created and with it the at-

Jan 6, 1951

By Ernesto Diez-Canseco Yañez

El siguiente trabajo señala los modos de aprovechamiento del mineral de carbón denominado "andracita", en tanto materia combustible de producción de las briquetas. Es decir, se busca crear un producto biocombustible que mantenga su calidad ecológica y que a su vez genere mayores posiblidades de venta en el mercado internacional, Para ello es necesario, evaluar el nivel de los aglutinantes en su composición y tratar de conservar sus características primigenias de dicho producto.

Jun 20, 1954

By L. Harris

Los finos de coque son materiales que se producen en toda planta de gas y coque y que no pueden ser usados directamente en los hornos metalúrgicos debido que sus propiedades físicas y quimicas ison ndeseables. En este sentido, los finos de coque se producen en altos hornos de fierro y plomo, donde una capa de carbón sin aglomerar y parcialmente coquificado, permanece en la parte superior de la carga y es durante esta descarga que se separa del coque grueso. Sin embargo, el coque descargado es muy grande para el horno y debe reducirse a un tamaño pequeño. Por tanto, el texto señala que para que el coque llegue a los hornos debe contener más de 20% de finos y en el caso de los hornos de plomo, es necesario que se separe de los finos debido a que puede generar un sofocamiento en el rendimiento de los hornos. Así también, describe la operación de la planta de coque en La Oroya, como las características deseadas del coque.

Nov 20, 1967

By José Velasquez, Peter Espinoza

El presente estudio se centra en el cálculo y análisis de las velocidades de las ondas P y S, y su relación con el mapeo geomecánico en diferentes formas (GSI, RMR, Q), con el objetivo de establecer que el parámetro “b” y su relación con estas velocidades son indicadores estructurales de la calidad de las rocas en yacimientos mineros. Esto proporcionaría una aproximación más precisa del mapeo geomecánico realizado por medio del sistema de monitoreo microsísmico instalado en la mina Pencas de la veta Choloque en la U.P. Marañón correspondiente a Compañía Minera Poderosa S.A. y su evaluación en campo

Sep 29, 2023

By John Mills

THREE case histories from professions other than engineering will serve to introduce ideas basic to this discussion. Case (1) Date, about 1900. A young man, B. D. from a three-year graduate course in a prominent divinity school, was for two years a successful pastor of a small church; then friction over theological matters arose with a fundamentalist deacon of the "Bible belt" type. He resigned, returned to his university for a four-year medical course, interned for two more, and thereafter was successful and apparently happy as a physician. We may assume that he was converted in early adolescence and vowed himself to service as a minister. Acceptance of his announced career by parents, friends, and teachers plus his own determination confirmed his choice until illiberal criticism threatened his usefulness and he awoke to the fact that his inner needs were not along the direction in which inertia and his conscience had constrained him.

Jan 1, 1947

By Augusto V. Ramírez

"El presente texto revisa algunos aspectos de la historia minera en los Andes Centrales -particularmente la negociación minera de Aguas Calientes, ubicada en Casapalca. La mina data de 1917, cuyo propietario fue Ricardo Bentín Sánchez. Asimismo, se revisa los antiguos procesos de extración y ventilación, la oficina de concentración, enfermedad y accidentes de trabajo y los aspectos sociales de la vida en Aguas Calientes. "

Feb 1, 2017