Search Documents

By Robert M. Doerr

The research objective was to determine the effect of vanadium alloy additions on the oxidation behavior of cobalt-nickel Alloys. Eighteen alloys were reacted with 0 2 at 0.5 arm and 1,351°, 1,389°, and 1,429° K. The alloy compositions consisted of Co-Ni master alloys (0, 22, 50, 70, 91, and 100 wt pct Ni) with V additions of 0, 0.9, and 2.7 wt pct. Large early deviations from, or changes in, the parabolic rate constant were encountered, but the reaction rate in most cases declined approximately in accordance with the parabolic rate law. Relatively, the vanadium degraded the oxidation resistance most at the highest nickel contents. In some cases, melting of the oxide was inferred from microscopic evidence and X-ray diffraction measurements disclosed the presence of low-melting vanadates.

Jan 1, 1970

By Alfred E. Schwaneke

The surface tension from 240° to 844° C and the density from 236° to 583° C of 99.999 percent purity liquid tin has been measured using the maximum-bubble-pressure method. Results for surface tension (y) show y (dynes/em) = 566.84 -4.76 X 10-2 T (° C) with a standard error of 1.9 dynes/cm. Results for density (p) show p (g/cm3) = 7.16 -6.3 X 10-4 T (° C) with a standard error of 0.012 g/cm3. Comparisons with other data found in the literature are discussed. The experimental results are considered to be as good as any data presently available.

Jan 1, 1970

By Ernest L. Corp

The natural marine environment can be divided into four basic categories: the air-sea interface, the water zone, the seafloor, and the subbottom. Efforts are being made to accumulate data to delineate the conditions in each of these areas and to conduct engineering studies which will determine how these environmental parameters affect the mining process. Laboratory facilities have been constructed and equipment and techniques for scientific data collection and laboratory research have been developed. Major emphasis is being placed on studying the subbottom material. The objective of this emphasis is to study the engineering properties of marine placer deposits in order to assess their influence on the design and performance of the various mining subsystems involving penetration, excavation, transportation, and disposal. Presented are the results of engineering properties tests on a placer simulant which is currently being used for model and prototype testing of coring tools. The effect of these engineering properties on penetrability, core recovery, and sample recovery is discussed.

Jan 1, 1970

By R. Newman

An inexpensive slow-speed data acquisition system has been adapted to digitally record multiple parameters simultaneously at intervals of 15 seconds. The system was built for use with standard soils testing equipment to automatically record load and displacement parameters at predetermined instants in time. Simultaneous readout is achieved by the use of special signal conditioner and sample-and-hold circuits which read the multiple signals simultaneously and hold them until the slow acting system can print out. Three channels of a 10-channel system have been converted and found to operate successfully during a series of direct shear tests. A unique feature of the system, which significantly reduced its cost, is the power supply units. Dummy circuits are used to maintain a constant power demand during sampling) thus eliminating the need for a costly power supply with rapid response characteristics. The entire system, having an overall accuracy of 0.25 percent, was put in operation for a cost under $2,500.

Jan 1, 1970

By J. Vance Batty

The Permian Red Bed copper deposits of the South Central States are a potentially important resource. Only the higher grade, near-surface ores are now exploited because conventional froth flotation does not recover oxidized copper minerals which comprise 10 to 15 percent or more of the copper content of typical ore. Laboratory-scale beneficiation studies were initiated to devise a method capable of recovering both sulfide and oxidized copper mineral. Testing established that the high clay and gypsum content of typical ore prevented effective flotation of the oxide mineral using sulfidizing, fatty-acid, or oil emulsion techniques. A modified leach-precipitation-flotation (L-P-F) procedure recovered over 90 percent of the copper, compared to a recovery of 77 percent obtained by conventional sulfide flotation. The higher costs of the L-P-F method would reduce the increased revenue from higher copper recovery. An increase in copper price and/or an increase in oxide copper content of the ore would make the L-P-F process comparatively more attractive.

Jan 1, 1970

By Manuel Gomez

The purpose of this study was to evaluate the feasibility of using statistical response surface regression analysis to predict the sulfur and ash distributions and the washability characteristics of coal along a seam in advance of mining. Prediction equations were developed with experimental data from channel, bench, and core samples from the Pittsburgh coal seam in Greene County, Pa. It was not possible, with the available experimental data, to construct mathematical models to predict ash and sulfur concentrations between sample points. In the authors' opinion, however, the good agreement between experimentally determined and predicted values at given sample points demonstrates the usefulness of the method. More input data, such as geologic information, seam characteristics (rock-to-coal ratio), petrographic analysis, and chemical data, would perhaps make it possible to predict sulfur and ash concentrations and washability characteristics between sample points.

Jan 1, 1970

By R. B. Tippin

To study continuous operation of the heavy liquid separation (HLS) of minerals, the Bureau of Mines concentrated spodumene from a typical ore. The studies included heavy liquid concentration, removal of the heavy liquid from the mineral products, and recovery of the heavy liquid for reuse. The research program examined the influence of feed moisture, steam consumption, stripping time, and condition of steam. Operation of multiple cyclones in series resulted in spodumene concentrates assaying 92 to 95 percent spodumene and indicated mineral recoveries of 86 to 89 percent. Continuous filtration and steam stripping produced mineral products containing less than I pound of heavy liquid tetrabromoethane (TBE) per ton of material. Problems unique to this process are discussed, including heavy liquid properties and viscosity, toxicity, material handling hazards, and safety precautions.

Jan 1, 1970

By James C. Patterson

Sintered fly ash was shown to have promise as a modifier for poorly drained soils. Turf grown in mixtures of sintered fly ash and soil benefited from increased water-infiltration rates, greater total pore space, and higher moisture availability, The result was an improved turf stand with increased grass yield and root density.

Jan 1, 1970

By Larman J. Heath

Wellbore enlargement was tested using hydrazine hydrate in a gas-storage well in Ohio to increase the well productivity. The wellbore was to be enlarged by chemical disaggregation of the sandstone adjacent to the wellbore. Productivity immediately declined 49.1 percent and gradually declined to zero in 7 months. A down-hole camera survey showed a white-to-gray precipitate covering the entire wellbore surface. The precipitate was chemically analyzed and identified as mostly carbazic acid, a hydrazine derivative of carbonic acid. Formation of this precipitate was not anticipated; this viscous sub-stance caused the gradual loss in productivity of the well. The wellbore was not enlarged. Laboratory tests were run to determine what clay stabilization measures could be taken in sandstone cores to prevent clay swelling and particle migration caused by hydrazine hydrate. Normal clay stabilization methods did not prevent the virtually complete loss in permeability to hydrazine hydrate. Other laboratory tests using natural gas diluted with small amounts of carbon dioxide confirmed the ease with which carbazic acid could be formed in a hydrazine hydrate-saturated environment within and adjacent to the wellbore.

Jan 1, 1970

By George S. Koch

The distribution of gold in part of the Getchell mine, Humboldt County, Nev., is presented through the statistical analysis of 956 assays of rock cuttings from wagon-drill holes. Two methods to predict grade in undeveloped parts of the ore body are evaluated, and the possibility of sampling bias is tested. The distribution of gold is compared with that in three other Nevada gold deposits of the same type characterized by gold particles mostly of submicron size associated with carbonaceous rocks, and also with that in deposits with coarse-grained gold. Usually, fewer samples of a given type are required to make a satisfactory grade estimate for submicron deposits than for coarse-grained deposits. The economic consequence is that submicron gold deposits are likely to be less expensive to sample and evaluate than coarse-grained deposits.

Jan 1, 1970

By R. L. Blake

The crystal structure of hematite, a-Fe203, has been refined as part of a continuing study of the behavior of phases in the Fe-O system during reduction and oxidation. Three-dimensional diffraction intensities were collected on two spherical single crystals of hematite with a semiautomated Buerger single-crystal diffractometer. The first crystal refined was a natural Elba hematite with minor impurities. The other, a synthetic crystal, was refined at the request of Mossbauer spectroscopy investigators concerned with impurities in the natural crystal. The structure has been refined with a least-squares program and the final structure for the natural crystal irradiated with CuKa-radiation gave a discrepancy factor (R) of 3.65 percent using 49 unrejected reflections of the 51 measured. For the synthetic crystal, using MoKa-radiation, the discrepancy factor converged to 2.8 percent using 95 unrejected reflections and was 3.3 percent for all 109 reflections. The structure model of Pauling and Hendricks has been confirmed with essentially no change in the iron coordinates and approximately a 5-percent change in the oxygen coordinates. Selected interatomic distances and angles were calculated as were anisotropic temperature factors.

Jan 1, 1970

By G. H. Keith

Electrowon tungsten powders were investigated with respect to consolidation, fabrication, and mechanical properties. Sheet, 0.03 inch thick, was produced and its tensile strength measured between 250° and 1,935° C. The large particle size of electrowon tungsten effectively precluded sintering to a density sufficient to allow hot working to sheet or bar. The powders were consolidated by die pressing to 70-percent density, sheathing in molybdenum, and high-energy-rate extruding to either round or sheet bar of 100-percent density. The material was then rolled conventionally to sheet. The mechanical properties of the sheet prepared from the electrowon powders compared favorably with those reported in the literature for sheet prepared from commercially produced hydrogen-reduced powder.

Jan 1, 1970

By Daniel C. Boteler

Five lignites from the northern Great Plains province were carbonized at temperatures from 500° to 1,000° C in a bench-scale unit. A replicated Greco-Latin square experimental design was employed to allow testing of four independent variables at five levels. Independent variables investigated were temperature, source of lignite (mine), weight of charge, and moisture content of charge. Dependent variables were char yield, tar yield, light-oil yield, tar plus light-oil yield, carbonization gas yield, and carbonization gas heat yield. An analysis of variance indicated that, at the 99-percent confidence level, the independent variables of carbonization temperature, source of lignite, and weight of charge were significant for yields of char, tar plus light oil, and carbonization gas, whereas moisture content was only significant for carbonization gas yields. At the 95-percent confidence level, moisture content significantly influenced the carbonization gas heat yield per pound of lignite charge and the yields of dry tar plus light oil. All dependent variables were determined on a moisture- and ash-free basis. Multiple regression equations for predicting seven different factors of carbonization yields as functions of carbonization temperature and initial composition were developed using computer techniques. Equations for yields of char, tar plus light oil, and carbonization gas were compared with equations previously developed by others at the 500° C level.

Jan 1, 1970

By Joseph L. Condon

Fifteen shots of three explosives with charge weights of 0.52, 1.1, 3.1, and 5.1 kilograms were fired in a pond to study the seismic effects of detonating explosives in water. Shock pressures and bubble periods were measured with pressure transducers in the water. Vibrations were measured on land in three orthogonal directions with particle velocity gages. Statistical tests indicated that a charge weight exponent of 0.43 best scaled the data. While shock pressures and bubble periods showed considerable differences in explosive performances, the amplitudes of ground vibrations showed less difference, and one prediction equation was therefore derived to estimate vibration amplitudes from all the explosives.

Jan 1, 1970

By H. R. Babitzke

As part of a continuing project to develop refractory metal alloys for high-temperature structural applications, the Bureau of Mines applied solid solution and precipitation strengthening techniques to improve the properties of columbium alloys. The purpose was to investigate the effects of hafnium, tungsten, and boron on the formability, strength, and oxidation resistance of columbium. The experiment was of factorial design with two replications which called for 72 ingots of 36 basic compositions, weighing 150 grams each. Hafnium, tungsten, and boron were evaluated at 3, 3, and 4 levels, respectively. Values of alloy content are all in atomic percent. The highest strength observed was 29,000 psi at 1,200° C for alloys Cb-15Hf (No. 3), Cb-7.5Hf-5W-2B (No. 14), and Cb-15Hf-5W-2B (No. 15). At 1,200° C, the ternary alloy Cb-15Hf-5W (No. 6) which has shown good properties in previous Bureau of Mines investigations was the most resistant to oxidation For boron additions, the alloys oxidized more readily with increasing amounts of this element. The fabricability of the alloys high in boron became increasingly difficult, resulting in an inadequate number of alloys required for a complete statistical analysis for all the tests. As a result of the decrease in ductility, an insufficient quantity of tensile samples were available for a proper analysis for the high-temperature strength data.

Jan 1, 1970

By B. H. Eccleston

The effect upon automobile emissions in changing from leaded to lead-free gasolines was studied in experiments by the Bureau of Mines in cooperation with the American Petroleum Institute. Typical U.S. leaded gasolines and prototype lead-free gasolines of comparable octane quality were used in eight vehicles operated to simulate city driving. The experiments were run at 70° and 95° F. Exhaust and evaporative emissions were measured and the photochemical effect of the emissions was experimentally observed in an artificial smog chamber. Results of the study reveal the manner and degree in which the changes in fuel composition alter the amount and characteristics of both exhaust and evaporative emissions. Briefly, it is shown that the compositional differences between leaded and prototype lead-free fuels resulted in higher photo-chemical pollution potential of the emissions from the lead-free fuels. The effect is attributed to the photochemical characteristics of high-octane fuel components that are used in greater quantity in the lead-free fuels.

Jan 1, 1970

By W. R. Hardwick

Nuclear explosive fracturing has been suggested as a method to make hard rock amenable to extraction by a modified block-caving method. To evaluate this possibility, conventional and nuclear blasting practices are discussed, underground mining methods for large deposits and their costs are described, and the cost of fracturing ore with a nuclear explosive and subsequent mining by a modified caving system is estimated and compared with both open-stope and block-caving mining costs. While the direct cost of fracturing the ore in hard rock with a nuclear explosive is less than with conventional explosives, additional costs imposed by the use of nuclear explosives may make their use unattractive for deep mining.

Jan 1, 1970

By K. Robert Dorman

Spray-applied polyurethane foam was used to insulate the walls of heated rooms excavated in permafrost. The experiment was designed to determine whether polyurethane foam can be sprayed successfully on frozen ground under freezing conditions and to measure the effectiveness of the insulation in maintaining--at elevated temperatures for an extended period--a room excavated in frozen ground. Two manufacturers' foams were investigated in the laboratory. Subsequently, one of the foams was employed to insulate two small rooms, one in frozen gravel and one in frozen silt, in an experimental tunnel belonging to the U.S. Army Cold Regions Research and Engineering Laboratory (USACRREL) near Fairbanks, Alaska. Following insulation, heat was introduced into the two rooms. Heat migration across the insulating barrier into the walls, in addition to wall closures, was monitored over an 8-month period. The results show that polyurethane foam can be successfully sprayed on frozen ground in below-freezing temperatures. Given this type of insulation, together with winter cold to supercool the surrounding ground, it should be possible to maintain a shaft or heated room in permafrost for several years.

Jan 1, 1970

By G. H. Keith

A vanadium-base alloy consisting of the following elements in weight-percent--molybdenum, 20; titanium, 10; carbon, 0.1; silicon, 0.5; and yttrium, 0.5--had exceptionally high strength at temperatures up to 1,200° C. This alloy was capable of fabrication to sheet of ~ 1 mm thickness by a combination of hot swaging and hot and warm rolling. In the warm-rolled condition at ambient temperature, its ultimate tensile strength was 1,205 MN/m2. The strength at 1,200° C was 150 MN/m2. Within the temperature range of 25° to 1,200° C, the ductility of the alloy as measured by elongation increased from 4 to >90 percent. Strengthening was achieved by both solid-solution and dispersed-phase mechanisms. Alloys of 20 percent molybdenum and 10 percent titanium were stronger than the other molybdenum-titanium alloy compositions tested. Strength was increased 15 percent in the temperature range of 25° to 800° C, with no accompanying loss in ductility, by the addition of 0.5 percent silicon. Workability was improved by additions of 0.25 and 0.5 percent yttrium.

Jan 1, 1970

By W. R. K. Wu

This Bureau of Mines report presents a statistical study of the repeat abilities of coal-plasticity parameters obtained in the tests with the Gieseler plastometer and the Audibert-Arnu and Hoffmann dilatometers. Repeatability is expressed in terms of one or two standard deviations for the differences between duplicates. The statistical method employed here is summarized. Results are tabulated for the temperature and nontemperature parameters of the three tests.

Jan 1, 1970