Search Documents

By Green R. E.

The removal of silica from commercial iron oxide concentrates by dissolution with sodium hydroxide was investigated by the Bureau of Mines as a means for producing supergrade concentrates. The effects of strength of solution, temperature, and digestion time on the extraction of silica were evaluated using eight iron oxide concentrates. Silica extraction from the eight concentrates was enhanced by autoclave leaching in the temperature range of 150° to 250° C and varied from 70 to 95 pct depending on the concentrate used. Superconcentrates containing less than 2 pct Si02 and more than 69 pct Fe were made only when magnetite concentrates were leached in the autoclave. The investigation showed that it is not difficult to obtain a supergrade product if the gangue is mainly quartz.

Jan 1, 1973

By C. A. Komar

Laboratory-scale hydraulic fracture tests were conducted by the Bureau of Mines on directionally oriented sandstone material, along with measurements of directional rock properties such as tensile strength, permeability, ultrasonic velocity, and dynamic elastic constants. In these tests, fracture orientation was determined as a function of various combinations of stress, rock saturation, rate of borehole pressurization, and direction of minimum tensile strength relative to minimum horizontal compressive stress. The objective of the experiment was to investigate whether horizontal stresses always controlled the orientation of induced vertical hydraulic fractures, or if under conditions of small differences in stress and/or slow borehole pressurization rates, the induced fracture direction was influenced by directional properties of the rock matrix. This study shows that the expected influence of horizontal earth stress on the orientation of an induced hydraulic fracture becomes negligible when¬ever the magnitude of the difference between the compressive stresses is 200 psi or less. When this occurs, fracture orientation is controlled by the directional properties of the rock--primarily permeability and tensile strength.

Jan 1, 1973

By B. V. Johnson

The Federal Bureau of Mines has conducted research in support of the National Aeronautical and Space Administration's (NASA) Apollo program to acquire fundamental scientific and engineering knowledge of lunar-mineral resources for NASA's Office of Advanced Research and Technology. Equipment and techniques were developed to conduct soil shear tests in a simulated lunar environment. Shear tests performed with this equipment in ultrahigh vacuum and controlled laboratory atmosphere showed that simulated lunar soil increased in strength in the simulated lunar environment.

Jan 1, 1973

By I. Liebman

A Bureau of Mines study is in progress to determine the effectiveness of passive water barriers in suppressing coal-dust explosions. A 2.9-ft3-capacity water-filled plastic tub was found effective in suppressing dust explosions propagating at speeds of 250 to over 1,000 ft/sec. Work directed at determining the limitations of water barriers showed that the passive water barrier technique is also feasible for the suppression of weak dust explosions propagating at speeds of 100 to 250 ft/sec. For relatively slow accelerating flames, dynamic wind forces appear to be the important quantity governing fragmentation of the plastic tub and subsequent water release and dispersion, whereas dynamic impulse appears to be the significant quantity for rapidly accelerating flames. The acoustic approximation (relation between static pressure and flame or wind speed) is shown to be valid in a long single mine entry. This relationship appears to be useful in predicting the regions within a long single entry where passive water barriers are effective in quenching a dust explosion.

Jan 1, 1974

By Charles C. Boley

Using bench-and pilot-scale coking facilities, the Bureau of Mines produced experimental coke from blends of char with Sunnyside coal (high-volatile A bituminous) from Carbon County, Utah. At bench scale, additions of char made from lignite improved resultant cokes when concentrations of up to 60 pct were used in the blends. At pilot scale (500-pound movable-wall oven), four chars made by entrained-bed carbonization techniques from the parent Sunnyside coal and from a North Dakota lignite were used in two-component blends with the Sunnsyide coal. Chars from Sunnyside coal had volatile matter contents of 5.8, 9.8, and 16.0 pct, moisture-free basis; the char from the lignite had 16.6 pct. In twenty-five 500-pound tests, improvement in coke quality was observed from all blends at char concentrations to 17.5 pct. The best coke, produced from a concentration of 12.5 to 15 pct of S.8-pct volatile char, exhibited physical properties approaching those of an industrial coke produced from Sunnyside coal blended with three higher rank blending coals. Studies were also made of the effects on coke quality of char source, of particle size, of comparative use of char and of a blending coal, and of prolonged coal storage.

Jan 1, 1973

By L. Cheng

This report describes a laboratory investigation of the effectiveness of low-pressure steam and a steam-water spray sequence for the collection of airborne respirable (<10 µm) coal dust. Comparison of present results to previous results obtained with water spray alone indicates that the use of steam in a steam-spray sequence increases the collection efficiency by about 14 percent over that obtained by water spray alone. However, the use of steam to collect airborne dust requires cooling the steam-dust mixture in order to achieve condensation of the steam, and steam does not appear to be an attractive approach for collecting airborne dust in underground coal mining operations.

Jan 1, 1974

By Robert Lee Stahl

Comprehensive field tests were made in the Gas Hills, Wyo., to determine whether surface geophysical techniques could be used to detect and delineate faults in marginal uranium deposits. The tests were made on property owned by Federal American Partners, Gas Hills, Wyo., and included seismic refraction, self-potential, induced polarization, magnetometer, electrical resistivity, airborne infrared thermal scanning, and airborne photography. Of the several geophysical techniques tested in the field, horizontal resistivity profiling with electrode spacings in the range of 25 to 50 feet was most diagnostic of faults. The method is quick, cheap, accurate, and one that can be easily used by personnel employed by mining companies to detect and delineate faults.

Jan 1, 1973

By Alexander May

In this Bureau of Mines publication stability constants for complexes of diethylenetriamine, 2-aminoethyl sulfide, triethylenetetramine, and 1,8-diamino-3,6-dithiaoctane with copper, nickel, zinc, and cadmium were deter-mined. The amine complexes were found to be much more stable than the analogous thio complexes. The results are interpreted in terms of possible molecular structure of the complexes.

Jan 1, 1974

By D. W. Frommer

Processing of nonmagnetic taconites by selective flocculation-des liming and anionic flotation of calcium-activated silica has been investigated using innovative procedures as a means of improving operating costs. Areas chosen for cost-cutting evaluation were grinding, fine screening, and water conservation and reclamation. The investigation was performed on Marquette range nonmagnetic taconites in the Bureau of Mines Twin Cities Metallurgy Research Center flotation pilot plant, at feed rates ranging between 900 and 1,100 lb/hr. With fully integrated water reclamation, flotation concentrates containing 65.8 percent Fe and 3.4 percent Si02 were made in the best operating period, with accompanying weight and iron recoveries of 40 and 74 percent, respectively. During this same period, the estimated cost of both flotation and water reclamation reagents was only $0.80 per ton of concentrate (1968 pricing basis). This cost is about 15 percent lower than obtained previously at this Center for flotation reagents only. The investigation demonstrated additional potential savings in operating costs of approximately $0.96 per ton of concentrate through autogenous grinding as a substitute for ballmilling. Fine screening of intermediate concentrates was employed advantageously, but the frequency of blinding may be a factor militating against use of the screen in this flotation system.

Jan 1, 1973

By E. G. Valdez

Laboratory research demonstrated that ceramic wall and floor tile can be produced from electric furnace phosphorus slags composed of calcium silicates. Grinding the slag in a pebble mill, followed by magnetic removal of deleterious magnetite, produced a raw material that could be compounded and formed into wall tile by dry pressing, sintering, and glazing. The effects of process variables such as forming pressure and sintering temperature were investigated. Wall tile bodies produced by this method were comparable to commercial tile. The tiles were readily glazed to a smooth shiny finish and met ASTM Specifications C34-62 for structural clay load-bearing tile. The estimated cost of producing wall tile by this method compared favorably with the retail market value for similar wall tile. Addition of borax or other additives to the ground slag followed by dry pressing and firing likewise produced a commercial grade of floor tile.

Jan 1, 1974

By J. A. Cavallaro

This Bureau of Mines report describes the preparation characteristics of 10 coal samples collected from the significant coal-producing mines of Lucas, Mahaska, Marion, Monroe, and Wapello Counties in Iowa, with special emphasis on physical desulfurization. All 10 samples were of high sulfur content as received, ranging from 4.2 to 10.4 percent; the organic sulfur content ranged from 0.8 to 3.8 percent. The pyritic sulfur content of the samples could be appreciably reduced by crushing and washing and provided pyritic sulfur reductions ranging from 36 to 75 percent. Crushing to 3/8-inch top size and removing the sink 1.60 specific gravity material would provide float coal products containing 3.5 to 6.0 percent sulfur. However, these coals could be burned at utility plants utilizing SO2 removal processes with efficiencies ranging from 70 to 88 percent and still be in compliance with the current Federal SO2 emission regulations for stationary sources.

Jan 1, 1973

By Richard E. Thill

Elastic wave velocities and moduli were determined by both the pulse and resonance methods in a large number of specimens of St. Cloud Gray Granodiorite and Tennessee marble under the same moisture, temperature, and stress environment. Long cylinders were first tested by the resonance method to obtain longitudinal bar and torsional wave velocity. The cylinders were then sectioned in half and tested by the pulse method to obtain the transient pulse velocity. These velocities were later used to obtain various moduli for comparison. Statistical comparisons between the Young&apos;s, shear, and bulk moduli and Poisson&apos;s ratios obtained independently by the pulse and resonance methods indicate that the methods do not give equivalent results in nearly isotropic rock. The amount of difference varies for each modulus, with the least difference (less than 5 pct) occurring in the shear modulus and the greatest difference (as high as 34 pct) in the bulk modulus. Moduli determinations in aluminum show much closer agreement between the pulse and resonance methods than in rock. The discrepancy in pulse and resonance results probably is caused by frequency dispersion effects and by differences in error sensitivity in the various formulas used to calculate the moduli.

Jan 1, 1974

By W. K. Kleysteuber

This report covers the design and testing of a novel bulk materials conveying device by the Bureau of Mines. The transport concept of the device is to create a traveling wave with a steep front so that the bulk material slides and cascades down the front of the wave with some horizontal motion. Ideally, the front should act like a continuous chute. The concept of moving bulk materials along a belt without any forward movement of the belt itself was demonstrated. The conclusions reached were that the mechanism as designed could not overcome the inherent major disadvantages that would make the undulatory conveyor suitable for practical applications.

Jan 1, 1974

By H. W. Leavenworth

Research was conducted by the Bureau of Mines to develop a technique to grow metallic fibers from a sulfide mineral. In this research, chalcopyrite (CuFeS2) was made sulfur deficient, and the remaining sulfur partitioned to the iron in the mineral to liberate metallic copper, or to the copper to liberate metallic iron. The metals formed on the surface as fibers and in the interior as spherical particles. Fiber growth is very fast. Lengths of 3 to 4 cm form in a matter of minutes, and the diameter of individual fibers is less than 1 µm. The mechanism of fiber growth is explained, and the reactions are reversible as predicted. Copper fibers can be made to grow from the surface at 400° C or to dissolve back onto the solid surface and be replaced by iron fibers at 625° C. Growth and dissolution can also be controlled to form copper/iron duplex fibers.

Jan 1, 1974

By J. M. Stuve

Thermodynamic properties were determined by the Bureau of Mines for the intermetallic compound, TiA13. Heat capacities were obtained from 5 to 303 K by adiabatic calorimetry. The derived value of S2 1s is 22.08±0.07 cal/deg¬mole. Enthalpies relative to 298 K were obtained from 298 to 1,413 K by copper-block drop calorimetry. No anomalous thermal behavior was noted in the temperature ranges investigated. Low- and high-temperature data were combined with a known enthalpy of formation at 298 K to give values of enthalpy of formation and Gibbs energy formation, 0 to 1,400 K.

Jan 1, 1974

By J. C. Franklin

The Spokane Mining Research Center of the Federal Bureau of Mines is placing major emphasis on chemical stabilization as part of the ground support program. Development of polymeric material suitable for bonding rock fractures around the mine opening is one phase of the program. Some of the problems that must be considered are viscosity, applicability, adhesion, cure times, strength, toxicity, and flammability. Epoxies and polyesters were investigated, but shrinkage in polyesters caused redirected effort toward epoxies. Test results with the latter showed that bonded fractures in mine-roof strata were stronger than the virgin rock. Further tests showed that polymeric materials have good potential for bonding, and in conjunction with polymer roof bolts, are expected to result in an economic and useful new support concept.

Jan 1, 1974

By H. E. Perlee

Mathematical expressions are derived for the histories of the pressure, flame radius, mass fraction burned, and burned and unburned gas temperatures associated with a spherical flame propagating concentrically in a spherical vessel. The equations are solved numerically for a 9.5 pct CH4/air mixture using the best available information for the burning velocity, expansion ratio, and specific heat ratio. Calculated histories are in complete accord with experimental measurements. The accuracy of calculated histories is determined relative to errors in the system parameters, and it is found that 10 pct errors in either the burning velocity or the expansion ratio results in a 40-pct error in the pressure history. A 10-pct error in either burned or unburned specific heat ratio results in a 22-pct error &apos;in the pressure history. It was further established that the usual assumption of constant specific heat ratio is unacceptable, but equating the burned and unburned specific heat ratios result in no apparent error in the histories. The cubic law (P = Kt3 + Po) is derived and discussed, and it is found that the law is valid only during the early period (P<2 atm) of flame growth.

Jan 1, 1974

By R. W. Watson

This Bureau of Mines report summarizes some recent results on the sensitivity of various experimental explosive systems using ammonium nitrate (AN) as the oxidizing agent. The sensitivity survey included drop-weight and friction testing and sensitivity to initiation by projectile impact and a No.8 blasting cap. It was found that certain types of AN prills can result in cap-sensitive mixtures when combined with No.2 diesel fuel (Fa); prilled AN mixed with nitromethane also result in cap-sensitive mixtures. Mixtures of AN prills and neat 1-and 2-nitropropane were not cap-sensitive, and the use of powdered or grained aluminum in AN-FO did not adversely affect the sensitivity except possibly to increase its sensitivity to friction.

Jan 1, 1974

By Manuel Gomez

A computerized moving average technique was developed to interpolate coal seam characteristics between sample points. The interpolative method coupled with multivariate regression analysis and simulation procedures was used to forecast coal properties not readily obtained from an analysis of drill core samples. Coal property forecasts were of two kinds: (1) specific mine property forecasts that are suitable for mine product control and yield a good approximation of the local variation along both the vertical and horizontal axes of the seam, and (2) regional estimates where much of the local seam variation is smoothed out, but the general trends are maintained. Forecasts of the volatile matter, ash, total sulfur, and the heating value for part of the Pittsburgh seam located in Ohio, Pennsylvania, and West Virginia were in good agreement with independent evaluation data. Spatial configuration for preparation characteristics, particularly, the effect of crushing on sulfur release, low-and high-temperature carbonization properties, the Hardgrove grindability index, the coal hardness index, gasification variables, and hydrogenation factors were constructed for the same area of the Pittsburgh seam. These forecasts may be developed from drill core data collected in the exploration phase of mining. The results, which may take the form of a series of maps, are useful to mining, chemical, and combustion engineers, to economists and mine managers, as well as to coal users for mine design, economic analyses, energy forecasts, utilization studies, mine product control, and environmental control and programming.

Jan 1, 1974

By Daniel C. Boteler

Data from 68 entrained-bed carbonization tests were treated statistically by the Bureau of Mines, and several useful relationships were developed among the major variables. Nine coals, ranging in rank from lignite A to high-volatile A bituminous, were carbonized in two entrained-bed carbonization pilot plants. The carbonizing reactors employed were vertically mounted cylinders, internally heated, refractory-lined, and 10 inches ID. The range of carbonization temperatures was from 825° to 1,600° F. Using a regression-analysis computer program, empirical equations were developed by which carbonization temperature, air-to-coal ratio, devolatilization of coal, char yield, and volatile matter content of product char may be predicted.

Jan 1, 1973