Search Documents

By Ann G. Kim

The U.S. Bureau of Mines mine fIre diagnostic methodology to locate and monitor fIres in abandoned mines and waste banks is based on the controlled sampling of the mine atmosphere to determine changes in the concentration of hydrocarbons desorbed from heated coal. To provide background data for this methodology, a laboratory study was conducted in which samples of coal and coal waste were heated under controlled conditions. Gas samples from the combustion furnace were analyzed for standard gases CO2 and CO and for the C1 to Cs hydrocarbons. In all tests, the concentration of desorbed hydrocarbons increased during heating and decreased during cooling. A dimensionless hydrocarbon ratio, Rl, was developed as the signature for heated coal. For bituminous coals, the value of Rl increases during heating of coal samples and decreases during cooling of the same samples. Generally, Rl values of 100 or more indicate coal sample temperatures of at least 100° C. The emission of higher molecular weight hydrocarbons from anthracite samples was very low, resulting in relatively low Rl values at all temperatures. Data from fIeld projects confIrmed these results.

Jan 1, 1991

By D. J. MacDonald

As part of a U.S. Bureau of Mines program seeking improvements to the Bayer process, a typical Jamaican bauxite was heated at temperatures up to 500° C in hydrogen, and its leachability under Bayer process conditions was measured and properties of its leached residue were observed. The objectives were to find ways to decrease the amount of organic carbon in bauxite or in leach liquor derived from it without impairing its leachability, and to improve the leached residue's filterability. Techniques employed included heating bauxite under pressure in an autoclave with hydrogen, and in flowing hydrogen at ambient pressure in a tube furnace. Leaching tests were done with a 600-mL stirred reactor. In some of the leaching tests, ferrous sulfate (FeS04) was introduced before leaching to produce a partially magnetic product. Results showed that exposure to hydrogen at temperatures from 160° to 360° C progressively diminished the bauxite's content of organic carbon and decreased the ratio of organic carbon to aluminum in leach liquor, an improvement that would allow a process using hydrogen-treated bauxite to be operated at a smaller recycle ratio, thereby consuming less energy and allowing greater throughput for a plant of given capacity. The bauxite's leachability was not impaired by high-temperature pretreatments, except at temperatures higher than 280° C. Pretreatments in hydrogen produced black, partially reduced bauxite which upon leaching gave a residue that was attracted to a magnetic field and was amenable to separation from green liquor by a magnetic filtration method.

Jan 1, 2010

By J. K. Whyatt

Researchers at the U.S. Bureau of Mines have been exploring recent advances in the use of strain-softening constitutive laws that approximate shear fracturing. The purpose of these tests is to investigate shear-fracture-related rock bursts in hard-rock mines. The capabilities and remaining problems in the use of strain-softening laws in finite-element, distinct-element, and finite-difference methods are reviewed. Performance of the finite-difference implementation of strain softening is compared to classic experimental results and observations of rock mass behavior in the Coeur d'Alene Mining District of northern Idaho. The results show promise for developing methods to identify the general location and orientation of shear fractures and their sequence of occurrence, but such methods cannot be relied upon to quantify post-fracture loads or displacements accurately. Uncertainty over the amount of energy consumed by failing rock and the dependency of energy consumption on model mesh definition prevent direct application of the results to analyses of rock bursts.

Jan 1, 2010

By D. A. Rice

As part of its mission, the U.S. Bureau of Mines continues to develop technologies that will enable cost-effective compliance with environmental requirements. To this end, investigations to improve the kinetics of chalcopyrite dissolution by simultaneous grinding-leaching in ferric sulfate solution were conducted using the Bureau-designed turbo mill. The development of such a hydrometallurgical process would provide a nonpolluting alternative to conventional smelter technology. The effects of mill rotational speed and volume percent solids on the leaching time and energy required for copper extraction from chalcopyrite were evaluated. The results of this laboratory study have shown that the simultaneous grinding-leaching of chalcopyrite concentrate using the turbomill is technically feasible with essentially 100 pet extraction of copper being possible at 90° C. An optimal energy consumption of 1,153 kW?h/st of copper leached was found in batch testing with the mill operating at 400 rpm with a slurry containing 35 vol pet chalcopyrite. This energy consumption, while higher than other proposed leaching processes (about 600 kW?h/st), is of the same order of magnitude. Further refinement of the energy requirements would require additional testing using a continuous circuit. Leaching times of less than 1 h, for 80 pct copper extraction, are achievable using the turbomill grind-leach process.

Jan 1, 2010

By G. W. Reimers

Exothermic oxidation reactions of sulfide minerals can produce self-heating situations in underground mines. If the self-heating is unchecked and the resulting heat is not sufficiently dissipated, the result can be spontaneous combustion fires. This U.S. Bureau of Mines report describes laboratory tests conducted to measure the reactivity of pyrite following treatment with additives to counter its self-heating tendencies. Thermal gravimetric analysis (TGA) and isothermal oxidation procedures were used to obtain information on pyrite ignition and the behavior of pyrite during low-temperature oxidation to ferrous sulfate. The determination of treatment effectiveness was evaluated by adding 5 wt pct of the compound to the pyrite before milling. The resulting samples were then heated in moistened air and after 24 h, the amount of pyrite oxidation determined. Results of these tests indicated that several phosphate compounds reduced the oxidation of pyrite to sulfate to about 50 pct or less compared with the oxidation of untreated sample at 200° C. Cupric sulfate reduced oxidation to about 20 pet untreated sample at 200° C. Sodium, calcium, and potassium chloride reduced pyrite oxidation to levels of approximately 15 pct or less of the untreated sample. Using only 1 pct of sodium or calcium chloride was effective in slowing pyrite oxidation to less than 20 pct of the untreated sample.

Jan 1, 2010

By D. L. Hollis

An arc plasma reactor, constructed and used for studying extractive metallurgical processing, was adapted by the U.S. Bureau of Mines to separate gases of different masses by using the high rate of plasma rotation. With argon and helium as input gases, peripheral reactor outlet ports had a measured average increase of about 10 pet in argon concentration relative to helium with the plasma on compared with plasma off for the same gas inlet concentrations in both cases. Approximately the same average increase in argon concentration occurred from the peripheral outlet port compared with a central outlet probe with the plasma on. There was no difference with the plasma off.

Jan 1, 2010

By V. R. Shea-Albin

This U.S. Bureau of Mines report discusses elastic wave velocity and attenuation behavior as an indicator for changes in load and structural integrity of coal samples. Measuring changes in compressional (P)-wave and shear (S)-wave attenuation and velocity under uniaxial and triaxial compression tests revealed their effectiveness for distinguishing changes in applied load and structural failure of samples. The velocity and attenuation values were used in further calculations such as ratios of P-wave to S-wave values, dynamic elastic constants, normalized velocities, and attenuation coefficients to reveal trends for loading and failure. The behavior of both P-wave and S-wave attenuation and velocity together define distinct and consistent phases of load change and failure for uniaxial and triaxial tests. The S-wave velocity and attenuation illustrate changing axial load and initial development of microfractures within the sample preceding structural failure more clearly than those of the P-wave. The attenuation and velocity ratios and dynamic elastic constants (except the bulk modulus) respond to closure of small preexisting fractures within the coal sample with initial loading to failure of coal samples. The attenuation coefficients and normalized velocities reveal trends similar to those shown by velocity and attenuation.

Jan 1, 2010

By J. L. Johnson

The U.S. Bureau of Mines investigated the recovery of tin and silver from the Coal Creek deposit in the Talkeetna Mountains, AK. Approximately 5 million st of reserves grading 0.2 pct Sn with silver credits of 0.2 tr oz/st have been delineated by drilling. A 10-to 25-pct Sn gravity concentrate was produced by treating the minus 20-mesh ore with a spiral, then regrinding to minus 65 mesh and tabling. Sulfide contamination in the gravity concentrate was as high as 60 pet. Sulfide flotation of this concentrate produced tailings containing 40 to 50 pet Sn. Overall recovery was 76 pct for tin but only 5 to 10 pct for silver because of losses during sulfide flotation. Other methods tested to clean the concentrate included cassiterite flotation, gangue flotation, nitric acid leaching, and wet and dry magnetic separation. Tin beneficiation tests on the minus 325-mesh fraction included cassiterite flotation, vanning, sulfide flotation, and fuming. The bench-scale and locked-cycle tests were used to estimate the mass flows for a 1,000-st/d plant.

Jan 1, 2010

By Larry A. Haas

The U.S. Bureau of Mines is investigating ways of enhancing the high-temperature softening-melting (HTSM) properties of domestic taconite pellets. These properties, which are important for determining the performance of pellets in blast furnaces, include pellet bed contraction, pressure drop, S-value (area under the pressure-temperature curve), and softening and metal-slag drainout temperatures. Experiments showed that HTSM properties were related to the physiochemical properties (fired strengths and reducibilities) of pellets containing different levels of limestone and dolomite flux. Flux additions resulted in slightly lower green and fired pellet strengths, but improved metallurgical properties, such as reducibility. The influence of reduction conditions on HTSM properties was evaluated by varying the pellet metallization starting temperature and the carbon monoxide content of the CO-N2 gas mixture. HTSM property change was more sensitive to flux addition levels when metallization was initiated at 1,100° C with 20 pct CO in the gas stream. The S-value and the metal-slag drainout temperature were found to be the best criteria for characterizing HTSM properties. The optimum flux addition level was about 8 pct (4 pct dolomite, 4 pct limestone) or a basicity of about 1. At higher flux levels, a higher metal-slag drainout temperature was obtained.

Jan 1, 2010

By Sathit Tandanand

Horizontal displacements and ground strains induced by mine subsidence are significant information needed for calculating damage and developing precautions against subsidence effects on surface structures. To devise a simple method for determining the surface horizonal displacements and strains simultaneously with the subsidence prediction, the U.S. Bureau of Mines examined the significance of the tilt number, which is the proportionality constant in the relationship between the horizontal displacement and the slope of the subsidence profile. The ratio of the tilt number to the critical radius of the subsidence trough is identical to the ratio of the maximum possible horizontal displacement to the full subsidence, which is found to be constant in most European coalfields. If this ratio is known for a particular minesite in the United States, then horizontal displacement and ground strains can be readily obtained from the primary subsidence data.

Jan 1, 2010

By Phillip W. Holland

The U.S. Bureau of Mines has developed a mass spectrometer method for determining helium in the parts-per-million to 10% range to an accuracy of ± 1%. The method employs a mass spectrometer, an inlet system utilizing a chromatographic gas-sampling valve, and an activated coconut charcoal trap cooled with liquid nitrogen. Gravimetrically prepared standards of helium in nitrogen were used to demonstrate the linearity of the method over the concentration range of 10 ppm to 10.66% helium.

Jan 1, 2010

By D. R. Tesarik

As part of its research program to investigate ways of improving resource recovery and reducing subsidence, researchers from the U.S. Bureau of Mines placed instruments in the B-North ore body of the Cannon Mine, Wenatchee, WA, to monitor cemented backfill and rock deformation during mining. The vibrating-wire gauges proved to be reliable and versatile, and approximately half of the instruments are providing data after 2 years of use. A two-dimensional, finite-element model was used to analyze the Cannon Mine's multilevel bench cut-and-fill mining method and predict rock and backfill displacements. The model accurately predicted rock displacements, but the predicted and measured displacements in cemented backfill had a correlation coefficient near zero, indicating that the model should only be used to predict rock displacements and not backfill displacements. A finite-difference model was also used to evaluate the stability of a cemented backfill pillar. Results can be used to conservatively predict backfill stresses, but on-site observation of pillar failures coupled with in situ measurements are needed to make more accurate predictions. An ongoing evaluation of the mining system has indicated that filling the primary stopes tight to the back with cemented backfill allowed these pillars to carry overburden loads soon after the cemented backfill was placed.

Jan 1, 2010

By W. P. Stroud

In this U.S. Bureau of Mines report, the conditions required for the direct reconstruction of a tomogram from observed line integrals are examined. Because of the limited access to the working faces in coal mines, the special case of access to only two opposite faces is emphasized. Classical matrix methods were used for small dimensional (2 by 2, 3 by 3, and 4 by 4) applications to determine the limitations and the requirements for a solution. The results for large (n by n) grids were then inferred and generalized from those of the smaller grids and matrices. Limited access tomography is found to be appropriate for in-seam hazard detection from seismic and microwave data, but it is shown that additional data must be added to obtain a direct solution.

Jan 1, 2010

By Robert J. Timko

In early June 1986, an underground fire of unknown origin erupted in one of several entries of a coal mine located in southwestern Colorado. For a time, mine personnel aggressively fought the fire. However, control of the fire was later lost. To prevent further damage and reduce the possibility of an explosion, all portals and shafts to the mine were sealed. The mine operator requested the U.S. Bureau of Mines' assistance in obtaining and analyzing mine fire gases taken from sampling ports placed through the mine seals, as well as down boreholes drilled after the fire. This report recounts activities within the first 2 years of the mine being sealed. It includes a description of gases analyzed and mine atmosphere status equations generated from the analyzed gases. The gases were analyzed by chromatography and included standard atmospheric gases as well as higher hydrocarbons that are found in postfire atmospheres. Nine equations were used to evaluate what was occurring within the sealed mine. Following a description of the rationale behind each equation, the 2-year trend is briefly analyzed.

Jan 1, 2010

By Louis E. Dalverny

U.S. Bureau of Mines research to develop diagnostic methods to locate and evaluate fires in abandoned mines and waste banks and techniques to extinguish such fires was applied to an abandoned 60-acre underground bituminous coal mine (Renton, Allegheny County, PA) to locate and extinguish three separated fire zones. Mine fire diagnostics interpret changes from baseline values in subsurface pressures, temperatures, and mine gas composition under imposed pressure gradients induced by a borehole exhaust fan. The effective gas sampling area surrounding each borehole is greatly enlarged. Sampling iterations, using a "communicating" boreholes set, provide "fire signature" information for locating both heated and cold areas. Time-dependent monitoring differentiates heating and cooling periods resulting from combustion front movement and/or fire extinguishment activities. A water injection with fume exhaustion extinguishment effort involved injecting water through boreholes to quench the heated zones while exhaust fans actively removed heated gases from the mine. The technique was ineffective as implemented, primarily because of inadequate spreading of water from the injection points. The Bureau's diagnostic method determined the fire locations and the effectiveness of the water injection with fume exhaustion extinguishment technique.

Jan 1, 2010

By R. A. Cortese

The U.S. Bureau of Mines has developed a flame-radiation-powered trigger device to explosively activate suppression barriers to quench gas and coal dust explosions. The major component of the device is a silicon solar panel, which converts radiation from the developing explosion into electrical energy to initiate an electric detonator, which releases an extinguishing agent into the advancing flame front. Solar panels that are rated to produce 20 W of electrical power when exposed to the sunlight are producing about 200 W when exposed to a full-scale dust explosion. The solar panel is electrically isolated from the detonator by a pressure-sensitive switch until the arrival of the precursor pressure pulse, which always precedes a deflagration. This combination of pressure arming and flame-powered photogenerator prevents false barrier activation and requires no external power supply.

Jan 1, 2010

By Dennis R. Dolinar

The danger to personnel, equipment, and pillar structure created by the spalling of a coal rib can be minimized by installing rib bolts. To assure that a configured support system will maintain a coal rib, the U.S. Bureau of Mines developed a rib bolt system based on a nonpreventable failure concept. A statistical equation quantitatively relates the amount of rib retained to the bolt spacing and the width of the spalled material. Laboratory test results show that the equation accurately predicts the amount of material retained and confirm the validity of the support concept. The examination of rib bolting at a coal mine experiencing rib sloughage provides evidence that the effectiveness of the support can be related to the failure pattern of the spalled material. An analysis of roof and roof support reaction to rib sloughage at the mine indicated that the rib sloughage had little effect on roof stability. Although supporting ribs might not affect roof stability, laboratory test results indicate that the material retained by the support can sustain a load up to 20 pct of the intact compressive strength of the material.

Jan 1, 2010

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine the hydrogen cyanide (HCN) concentrations and smoke particle characteristics during the combustion of flexible polyurethane foams and other nitrogen-containing materials, for the development of a test parameter. The experiments were conducted in an approximately 2O-L furnace at set furnace temperatures of 250° and 1,000° C for a 14-min duration, with an airflow through the furnace of 10 L/min. The variables studied as a function of time were the gaseous and aerosol HCN concentrations, the smoke particles average diameter (dg) and particle concentration (no), and the product of the smoke particle diameter and concentration (dgno). Carbon monoxide, carbon dioxide, and oxygen concentrations, sample mass weight loss, and furnace temperatures were also studied; analyses of nitrogen and cyanate content of the material were carried out. Results show that dgno correlates directly with the HCN concentrations, which depend on the nitrogen and cyanate contents of the material.

Jan 1, 2010

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine the embedded hydrogen chloride (HCI) and smoke particle characteristics during combustion of polyvinyl chloride (PVC) and chlorinated mine materials for development of a test parameter. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 250° and 1,000° C, for a 14-min duration, with an airflow through the furnace of 10 L/min. The variables studied, as a function of time, were hydrogen chloride embedded on smoke particles, hydrogen chloride concentrations in the gas phase, smoke particle average diameter (dg) and particle concentration (no), and product of smoke particle diameter and concentration (dgno). Other variables included carbon monoxide (CO), carbon dioxide (CO2), and oxygen (O2) concentrations; sample mass weight loss; and furnace temperatures. Results show that there is a correlation between embedded hydrogen chloride, hydrogen chloride gas concentrations, and inverse of the smoke particle diameter-concentration product (1/dgno); the higher the hydrogen chloride gas concentrations, the higher the embedded hydrogen chloride, the higher the 1/(dgno) values. These correlations will enable development of a simple test parameter to assess the toxic hazard that these materials pose during fire.

Jan 1, 2010

By G. T. Fisher

The U.S. Bureau of Mines conducted research on calcium ferrite slags to determine the distribution of Pb and minor elements (Ag, Cd, Zn, and Co) between Pb bullion and slag. These fundamental data are required to evaluate nonferrous smelting with calcium ferrite slags as a substitute for conventional iron silicate slags. Determinations were made in 25-cm3-capacity MgO crucibles at 1,250° C for 2 h in a CO-CO2 atmosphere with an O2 potential that would retard the formation of magnetite. Calcium ferrite slag composition variables studied were from 16 to 32 wt pct CaO in 2-pct increments and Si02 ranging from 1 to 5 wt pct in 1-pct increments with equal additions of MgO. For all compositions studied, the retention of Pb in the calcium ferrite slag was less than 1 wt pct, which compares favorably to about 6 wt pct Pb in conventional iron silicate slags used in smelting of Pb concentrates. Minor element distribution was insensitive to changes in slag composition in the range studied. However, slag composition had significant impact on the melting and fluidity of the slag.

Jan 1, 2010