Search Documents

By Satid Therdkiattikul, Donald A. Dahlstrom

By oxidizing the pyrite matrix through biological leaching of precious metals ores or concentrates, better than 90% recovery of gold and silver is achieved. The paper develops three precipitation processes that eliminates arsenic and all other toxic elements in the resulting liquor after the biological reactors. In addition, the precipitates are highly crystalline and resist resolubilization. The latter must be tested for at least six months by EPA test procedures. The three systems are temperature (must be at least 120°C or higher) lime or limestone. A continuous pilot plant was employed for all three systems and complete recommendations are given to optimize Fe/As molar ratio, reaction kinetics (detention time) pH, temperature, wt % feed solids as well as resultant reagent consumption based upon continuous operation.

Jan 1, 1995

By Satid Therdkiattikul, Donald A. Dahlstrom

Many gold ores are known to be refractory so that conventional cyanide processing will result in serious losses of gold and silver values. A significant percentage of these refractory ores contain aresenopyrite and the gold and silver is usually encapsulated within this matrix as well as the pyrite matrix. Normally the values can be recovered as flotation concentrates because of the sulfide compounds with recoveries of over 90% and at very good grades. In order to free the gold and silver, the sulfide matrix must be destroyed. This can presently be achieved by (1) pressure­temperature leaching (2) roasting and (3) bacterial leaching. All of them have advantages and disadvantages as well as an obviously increased cost for the each processing method. However, the increased gold and silver recovery should and must more than offset this cost. It is believed that gold recovery should be well over 90% from the concentrate so that overall recovery from the ore should be in the 90-95% region. All three processes must consider pollution control of both sulfur and arsenic to prevent contamination of air, water or land through improper waste disposal. This paper will concern only bacterial leaching and its necessary control of effluents and solids. Sulfur does not appear to be a problem as the element is oxidized to sulfate and is precipitated with an acceptable solubility. Other important improvements that must be controlled are arsenic and iron which are present as significant values (1-12 g/1 of arsenic, 20-40 g/1 of iron). In addition much smaller values of base metals, aluminum and magnesium can be present as well as other elements depending on the ore and these must be low enough after treatment to meet EPA regulations.

Jan 1, 1993

By Ramie H. Thompson

1.1 BACKGROUND In many underground coal mining operations the use of electromagnetic field equipment, particularly communication systems, not only increases the overall efficiency of the mining operation but can be directly linked with mine safety considerations. The use of electromagnetic field producing equipment in underground coal mining operations can only be expected to grow. Several new communication systems have already been proposed. In addition, high-frequency producing equipments for many diverse uses in mining operations are under study. The use of these equipment in underground mining operations is hampered by the possibility of their electromagnetic fields interacting with the electric blasting cap operations commonly carried out in the mines. Such interactions can have at least two results bearing directly on mine safety: o premature initiation of the cap, either in its normal shot location or during hookup or transportation; o dudding of the cap so that normal firing operations do not cause irritation; thereby leaving unexploded high explosives after normal firing. Since the consequences of a premature initiation could, particularly in coal mines operations, result in catastrophe involving human life, the overall approach to prediction of possible hazard must be, as far as possible, of a "worst case" nature. The general problem of predicting possible RF hazards for any electroexplosive device (EED) is best treated by reference to Appendix A of

Jan 9, 1983

Permit quicker, safer clearance of hang-ups in the ore passes and chutes of underground mines. Approach Develop a device that can be operated from a safe distance to explosively propel a projectile into the hang-up. How It Works The Hang-Up Clearance Module, consisting of a stand, steel disk, explosive charge, and aiming device, is placed at a location convenient for line of sight aiming at the hang-up. This placement can be more than 100 feet from the target. Once aimed, the charge is remotely detonated, and the disk is converted by explosive force into a slug and propelled to the hang-up, bringing it down. The steel disk and an explosive charge are contained by a plastic casing. A small booster which is placed at the rear center of the explosive makes up the last component of the charge. Initiation is accomplished by standard means such as detonating cord or a number 8 blasting cap. When Initiated, a detonation wave travels through the explosive, inverting and consolidating the steel disk into a large slug. This slug is propelled at high velocity to the hang-up, delivering more than 5 million foot-pounds of energy on impact.

Jan 1, 1981

By Walter Ensinger

Special foundation works is one of the most innovative sectors in civil engineering and construction. Both engineering techniques and construction machinery are undergoing continu­ous further development. These developments are providing ways to meeting the world-wide requirement for special geotechnical works even faster, even better and more efficiently. Unfortunately, accident prevention organisations have had to realise that the figures on in­dustrial accidents in special foundation works are still above average in number. The Safety & Environmental Working Group of the EFFC thereupon started to carry out a survey on acci­dents occurring in this sector and used this information as a basis for the preparation of acci­dent statistics and an accident analysis. The objective of this undertaking is to determine key accident occurrences and their causes and to consequently determine measures for improved health and industrial safety.

Jan 1, 2002

By K. Galovich, P. Krivokuca

"Quinsam coal mine is located about 25 km west of Campbell River on the east coast of Vancouver Island, British Columbia. Using continuous miners in a fully mechanized retreat room-and-pillar operation, it produces low sulphur, “super compliance” thermal coal for domestic and international markets at a rate of about 2600 t/d. Currently, 65 people work at the site, including some corporate employees.Opened in 1993, the Quinsam mine had a dismal safety record until 1997. Lost time injuries and medical aids were unacceptably high. In 1998, a change in corporate structure brought a change in safety attitudes; a total and unequivocal commitment to safety as job No.1 by corporate and site management. This commitment was clearly spelled out in a new mission statement, circulated to all employees by the new President and CEO, David Slater: “Safety is job No. 1; Production flows from safety; and Think safety at all times.” As well as re-defining workplace safety practices, QCC tightened engineering controls and enforced strict adherence to mine plans.This paper provides a general background to the mining operation, and describes the safety practices that have resulted in an enviable safety record in recent years, reflected by provincial and national recognition."

Jan 1, 2004

By Art Johnston

Gas handling at Magma Copper company's, San Manuel smelter receives process gas from a flash .smelting furnace and four copper converters. The major gas handling equip11lent consists of four electrostatic precipitators and a sulfuric acid plant. Process ,vessels in gas handling are, typically confined, spaces. Lethal gases, mechanical and chemical hazards, and the difficulty of rescue, should an accident occur, makes this area a must in the safety plan. The presence': of hazardous chemicals and explosive gases in process' vessels and piping are of major concern when repairs' are required. Proper job procedures are critical to prevent injury during repairs. This includes plant employees and contractors who are likely to be unfamiliar with the hazards ,involved. The safe operation of a gas handling operation must include the functions of operations employees on a daily basis. This includes a safe working environment and involvement of all employees in the safety program. If an injury does occur quick medical response is critical to prevent serious injury. Medical responders must be adequately trained and prepared to treat the injured person without becoming victims' themselves. The methods used at Magma Copper Company to deal with these safety problems are the focus of this presentation.

Jan 1, 1992

By Art Johnston

Gas handling at Magma Copper Company's, San Manuel smelter receives process gas from a flash smelting furnace and four copper converters. The major gas handling equipment consists of four electrostatic precipitators and a sulfuric acid plant. Process vessels in gas handling are typically confined spaces. Lethal gases., mechanical and chemical hazards, and the difficulty of rescue, should an accident occur, makes this area a must in the safety plan. The presence of hazardous chemicals and explosive gases in process vessels and piping are of major concern when repairs are required. Proper job procedures are critical to prevent injury during repairs. This includes plant employees and contractors who are likely to be unfamiliar with the hazards involved. The safe operation of a gas handling operation must include the functions of operations employees on a daily basis. This includes a safe working environment and involvement. of all employees in the safety program. If an injury does occur quick medical response is critical to prevent serious injury. Medical responders must be adeqliately trained and prepared to treat the injured person without becoming victims themselves.. The methods used at Magma copper Company to deal with these safety problems are the focus of this presentation.

Jan 1, 1992

By Gour Sen, Peter Bellairs

Blasting conducted in rock temperatures greater than or equal to 55°C (13 1 “F) and / or in rock containing sulphide minerals and their oxidation products can result in unplanned detonations. Blasting practices involving the identification of the affected areas together with the use of speciality explosive products and rigorous attention to quality control are required to safely blast in these types of environments. Sulphide dust explosions occur in some underground mines where the primary blast results in a secondary explosion of the sulphide rock dust which propagates some distance from the primary blast area. This phenomena results in considerable damage and the generation of significant volumes of toxic gasses delaying re-entry to the affected area of the mine thereby increasing both costs and safety concerns. The exothermic reaction between ammonium nitrate based explosives and rock types containing partially oxidised sulphides have resulted in numerous high risk blasting incidents. These reactions can occur at ambient temperatures and often result in premature detonations / deflagrations causing a great deal of consternation at the affected minesite resulting in lost production and considerable expenditure to solve the problem. Rock masses at elevated temperatures can also result in unplanned detonations unless appropriate precautions are taken. This paper discusses each of these hazards, cites some case studies and details appropriate generic safe and efficient blasting techniques for each of the above applications using appropriately formulated explosive products.

Jan 1, 2000

By Fidelis T. Suorineni

Rapid drifting enables quicker access to orebodies, higher production rates and a resultant reduction in production cost. The Mining Innovation, Rehabilitation and Applied Research Corporation (MIRARCO) funded by the Canadian Mining Industry Research Organization (CAMIRO) has developed a methodology for safe rapid drift development within the underground metalliferrous mining industry in Canada According to industry survey, about 36% of drift development cycle time is spent on support installation. MIRARCO has developed a methodology for safe rapid drift development based on minimizing time spent on support installation. The methodology includes a critical review of the rockmass classification systems, examination of current support practices in the mining industry and civil tunneling, review of rapid drift development practice in South Africa, introduction of risk hazard procedures to account for material property variability and the development of a WIZARD as a quick decision-making tool for the implementation of the procedures. A comprehensive field data collection procedure was put in place and data collected from various mines to verify and calibrate the support selection rationale. The findings of the research programme resulted in the development of an improved rockmass classification system and showed that construction effects have drastic influence on support levels but is often not accounted for in assessing support levels. Stress effects and structurally controlled failures are the other important factors to take into account in rapid drift development. Three support classes were established for safe rapid drift development as No Systematic Support, Light Support and Strong Support. The support levels took into account cost, rate of installation and safety based on compatibility with ground characteristics. This paper describes the methodology for safe rapid drifting within the underground metalliferrous mining industry in Canada and highlights the key issues and major drivers behind their continued development at the Geomechanics Research Centre within MIRARCO.

May 1, 2004

By Fidelis T. Suorineni

Rapid drifting enables quicker access to orebodies, higher productivity rates and a resultant reduction in activity costs. Increased advance rates, by examination of the key components (face preparation and drilling, hole loading and blasting, scaling, mucking and support installation) in the development cycle, and optimizing these processes is a high priority for research in the Canadian mining industry. Support installation time alone is typically 36 to 46% of the total development cycle time. A reduction in support installation time or techniques and alternative scaling strategies could result in significant gains in drift development advance rates. Support Staging and hydroscaling within the drift cycle could offer alternative drift development sequences that could reduce the overall cycle time. MIRARCO?s research into the support and hydroscaling processes for rapid drift development also suggests that there are many other factors (e.g. mine ventilation services) that have a significant impact on the rate of advance. These factors should be considered to promote and manage safe and rapid drift development. Constraints to the rapid drift development processes can only be overcome by sound construction management practices. In other words, the goals of rapid drifting can be achieved by the implementation of contractor-type construction management. This paper examines various constraints and processes affecting rapid drift development and draws attention to other factors affecting safe rapid drift development.

Apr 1, 2005

Provide an accurate, reliable means for determining when a sealed mine or mine section can be safely reopened after a fire. Approach The Bureau of Mines performed a research investigation that resulted in the development of a mathematical formula for deriving a quantity, called RATIO, which can be used to define when a sealed mine or mine section has returned to safe recovery conditions after a fire. Research Results There were two major results from this Bureau research. Over a period of several years, the Bureau of Mines conducted six experiments at its Bruceton Experimental Mine in Pennsylvania. The experiments involved sealing the mine after several tons of piled coal had been allowed to burn continuously for 2 to 3 days. Although gas data obtained during the experiments revealed nothing significant, measured smoke particle levels were found to correlate with the stages of combustion and temperatures of the smoldering coal pile. Moreover, it was found that no smoke particles are produced when high-temperature smoldering exists deep within the mass of the coal pile since the smoke particles are filtered by the coal surrounding the hot region. Smoke is emitted into the mine atmosphere only if combustion is occurring near exposed surfaces. As suggested by these findings, any decision to recover a sealed mine area based primarily upon the absence of smoke particles is not a wise derision.

Jan 1, 1988

By A. G. Royle

Sampling formulae for in-situ material, hard rock sampling and alluvial sampling are briefly discussed

May 1, 1991

By K. M. Ed

AN explosive is a solid or liquid substance which, when fired by some means, changes into a gaseous product occupying a volume very much greater than its original volume. The great speed at which this change takes place causes the explosive to exert a sudden blow on adjacent material. It is this action which is effective in blasting operations when the explosive, confined in a shot-hole, is fired. All explosives are similar in one respect, in that the change into the gaseous state is accompanied by the production of hot gases or flame. This results from the rapid combustion of the solid or liquid ingredients. Ex-plosives differ greatly, however, in the speed at which the reaction takes place. Black blasting powder, for instance, reacts comparatively slowly, hence the flame persists for an appreciable length of time. High explosives, on the other hand, react much more quickly; consequently, the flame is of much shorter duration. In 'closed-light' or 'gaseous' coal mines, the use of ordinary explosives is generally prohibited, due to their inherent ability to ignite gas or coal-dust by reason of the flame which they produce when fired. For instance, black blasting powder, which produces a flame of long duration, is not ordinarily considered safe to use in such mines; neither are ordinary dynamites, as their flames, while shorter than that of black blasting powder are, nevertheless, of sufficient temperature and duration to cause ignition of fire-damp or coal-dust. For this reason, specially formulated high explosives, called 'permitted' explosives, should invariably be used in such mines.

Jan 1, 1940

By K. M. Ed

MR. J. C. NICHOLSON: The author has discussed his subject in a very thorough manner. One difficulty is the tendency to regard a 'permitted' explosive as a 'safe' explosive. There is no such article as a safe explosive; any explosive is only as safe as the man who handles it. In making up the primer, the method illustrated in the paper is alright for the ordinary explosive but not so for the sheathed explosive, for the sheathing would be punctured. MR. T. L. McCALL: I fee! quite certain that there would be little, if any, trouble from flame shots or misfires if the author's suggestions were carried out. There is a tendency on the part of the shot-firer to over-shoot, so as to bring clown more coal for the miner, and frequently a shot has not sufficient burden imposed upon it. Shooting one hole may not only lessen the burden on an adjacent hole, but may practically release it altogether, in which case the second hole should be fired with a very small charge, or perhaps it might not be necessary to shoot it at all. While the paper refers to shooting in the coal only, it should be under-stood that the instructions given are equally applicable to brushing shots. I do not wish to bring up any contentious point, but would the author say a word on cushioning with air gaps and on multiple shooting? Single shooting in rock might open up a feeder of gas which could be ignited by the ?second shot.

Jan 1, 1940

By W. Burger

In underground mines worldwide, a large number of short and small diameter slot holes need to be excavated. Herrenknecht has developed and built a new boxholeboring machine based on the well-proven Microtunnellingpipe jacking technology. The innovative Boxhole Boring Machine significantly increases work safety and requires only minimal drift dimensions. The high and consistent production rates that can be achieved result in enormous time savings compared to conventional drill and blast excavations. GENERAL ASPECTS In gold, copper and ore mines ventilation shafts are required to prepare block caving operations, to discharge ore onto the transportation level and to provide evacuation shafts. A high level of occupational safety and efficiency is the main objective when drilling vertical or inclined shafts. The faster and more safely shafts can be constructed, the earlier the actual production in the mine can start or be continued. Mechanized or conventional methods (drill&blast) that have been used to date only partially meet the required safety standards and fail to provide the requested production rates.

Jan 1, 2012

By W. B. HILLHOUSE

AN excerpt from the Alabama State Mining Law, pertaining to, transporting men' into and out of the mines, reads as follows: "A trip of empty cars may be operated for the purpose of taking employees into and out of the mine, where the distance to and from their work exceeds one mile." The State Mining Department of Alabama includes in its inspection the transportation of men into and out of the mines, also studying and noting improvements, or progress made, that would tend to create a greater assurance of safety in this practice. Everyone is familiar with the original safety methods employed in man-trip transportation, such as passing a rope around the trip of cars, or through the cars, fastened in the conventional manner, and with the usual "clog," commonly called a drag, on the rear end. Also there is a more advanced method of transporting men, such as the double-rope system, which is feasible on slopes used exclusively for this purpose, and is very satisfactory. However, for the past eighteen months; the Republic Steel Corp. and the Tennessee Coal, Iron & Railroad Co. have adopted a practice that shows

Jan 1, 1935

By K. Adham

Both the dry and the wet fluorination systems require hydrogen fluoride (HF) for the process of uranium conversion to uranium hexafluoride (UF6). The dry methods depend on the electrolysis of HF to generate the fluorine (F2) required for the high temperature pyro-fluorination. The wet methods require aqueous HF in water solutions for the low temperature hydro-fluorination (Argonne, 2019). This paper uses the available HF safety guidelines and industry information to discuss the issues of transportation, storage and utilization. Health effects and environmental considerations are reviewed. Safe practices for handling the HF (both as anhydrous and as aqueous) are considered. Proper selection of different materials of construction are discussed, for both the anhydrous and the aqueous HF.

Jan 1, 2020

By John R. Poland, Benjamin Mirabile

"There are significant ground support hazards to both personnel and equipment when longwall equipment must mine through cross-panel entries. Backfilling support strategies are often cost prohibitive. Additionally, it is often very difficult to install backfill material in full contact with the mine roof in backfilled entries. This paper will demonstrate the use of fiber-reinforced concrete crib material as a method for standing support in longwall cut-through entries. Despite conceptions of poor performance in potentially high convergence environments, fiber-reinforced concrete crib material can be used in longwall support environments subject to high abutment loads and convergence. Central to the proper design of these supports is the use of yield material between crib layers and at the mine roof/crib interface. The placement location of cribs within the cut-through entry has a significant effect on the main roof behavior and associated ground conditions in the longwall abutment zones. It is particularly important to engineer the proper load displacement characteristics of the installed crib to support expected ground conditions. The cost of fiber-reinforced crib supports is less than 50% of backfilling methods.INTRODUCTIONThe design and execution of a longwall cut-through is perhaps one of the most difficult and risky endeavors in the field of ground control. The magnitude of abutment loads and potential for ground failure present a significant safety hazard to underground personnel. In addition, there is significant financial risk, with replacement costs of face equipment exceeding $200 million. Faced with these consequences, it is both advisable and common for an engineer to design ground support with a significant margin of safety. This paper outlines a robust support system that possesses a significant margin of safety along with significantly lower costs than most other support systems employed in similar conditions.SITE PARAMETERSThe mine site described in this study operates in the Herrin No. 6 seam in southern Illinois. The seam height is typically 76- 84 inches. Mining height in gateroads and mains is typically over 96 in, and typical mining height on the longwall face is 82 in. The overburden depth is 950-970 feet in the area of the longwall cutthrough."

Jan 1, 2016

By Shazad Hosein, William J. Birch, Robert Farnfield, David Jameson, Catherine E. Johnson

The current and consented quarry workings at a slate quarry in North Wales {UK} intersect old long abandoned underground slate mine workings. The old underground slate mine contains the remains of World War II buildings used to house artworks to protect them from war damage. Over the past 20 years, there have been a number of roof falls in the old underground slate mine, which have damaged the buildings and make general access unsafe. From observation of the timing of these falls, they occurred in the mid 2000’s. The purpose of the exercise was to determine the possible relationship between blast vibrations experienced on the surface and those experienced on the roof of the abandoned mine caverns. Thus preventing the need to regularly monitor in the old mine workings. In order to achieve this, a rigorous geotechnical assessment of the stability of the caverns was undertaken by a fully qualified Geotechnical Engineer. Once it had been determined that it was safe to do so, 3 “MEMs based” blasting seismographs were attached to the roof, in accordance with the instruction of the geotechnical engineer. In addition, 8 “MEMs based” blasting seismographs were deployed at various locations on the surface. The trial blast comprised of 51 blastholes, with charges varying between 46kg [101lbs] and 124kg [273lbs] of bulk emulsion explosive. The blastholes were in 4 rows of holes. The blast was connected using shock tube 25ms, 33ms and 65ms delay period relay detonators. The minimum distances from the blast to the surface and underground monitoring points were 78.1m [256 ft] and 114 m [374 ft] respectively. The results from the three underground monitoring locations in terms of resultant peak particle velocity was 4.42 mm/s [0.174in/s], 3.47 mm/s [0.137in/s], and 4.69 mm/s [0.185in/s]. In line with previous research, it was determined that the underground results [when compared on a “like for like” basis in terms of scaled distance] were lower in amplitude than the surface results. In this case by a factor between 0.47 and 0.87, averaging 0.68.

Jan 21, 2025