Search Documents

By BO HYUN KIM, MARK K. LARSON

The floor-heave and no-floor-heave phenomena at a western U.S. coal mine could not be properly simulated in numerical models using conventional shear-dominant failure criteria. Although the previous numerical study using FLAC3D very reasonably demonstrated these phenomena, 3DEC modeling in conjunction with the discrete fracture network (DFN) technique was performed to better understand the true behavior of floor heave associated with underground mining in an anisotropic stress field. As a result, the latter models predicted floor heave that agreed with relative amounts of observed heave from each gateroad system, but the cause of heave was mainly related to the degree of anisotropy instead of the size of the pillar.

Sep 1, 2022

By S. H. Morar

Froth flotation is a physico-chemical separation process that takes place in two phases; pulp and froth phase. It is widely recognised as a complex process, due to the range of interactions present within the system. Of critical importance is the role of the froth phase within the system. The pulp kinetics governs the maximum potential recovery within a flotation cell, while the froth phase governs the selectivity via the froth?s stability. Higher froth stability improves recovery at the expense of grade, and lower froth stability improves selectivity. It is well known that the two major factors affecting froth stability are attached particles and solution chemistry. This paper looks at a flotation bank at different froth depth and frother concentrations. The air recovery to the concentrate is determined at each condition and relates the effect of the operating conditions on froth stability and transport to the amount of solids that are recovered to the froth and concentrate by true flotation. The results presented show that, for a given process objective, which in this case was a consistent mass pull profile, depending on the operating conditions, solids recovery in the pulp is affected by the air rate required to maintain the target mass pull. To a smaller extent, the changes in the pulp composition affect down-stream pulp recovery. The variation in solids recovered into the froth drives the froth stability at the start of the flotation bank, while the frother drives the froth stability at the end of the bank. The performance in between these two extreme conditions arises from an interaction of these two effects. The consequences of these interactions can give rise to counter-intuitive responses that can confound efforts to optimise the performance of the bank.

Jan 1, 2014

By R. E. Utting

INTRODUCTION Until recently, gamma doses had been largely ignored in Ontario uranium mines. This has been due to the assumption that these doses are small and have been more or less unchanged with time and hence their effects have been included automatically in the epidemiological studies that led to the establishment of radon daughter exposure limits. This assumption had to be challenged for two basic reasons. The first was that radon daughter exposures to miners have been progressively reduced over the years due to improved ventilation and ever more stringent regulations, while gamma exposures have presumably remained relatively unchanged. Therefore it must be assumed that the ratio of gamma to radon daughter exposure has gone up. The second reason is more philosophical. It is clearly inappropriate to make judgements on the significance of a potential industrial hazard when the magnitude of that hazard has not been fully assessed. Having decided that some sort of assessment of gamma exposures to uranium miners must be made, it was than necessary to determine how this should be done. Several options were available, for instance: (i) Wholesale personal gamma dosimetry for all mine and mill workers, (ii) Personal gamma dosimetry only for those workers suspected of receiving the higher doses, coupled with area monitoring to estimate the exposures of other workers, (iii) Area monitoring coupled with dose rate times time calculations for all. This would correspond to the generally prevalent method of assessing radon daughter exposures. It was argued that since radon daughter exposures are the major radiological hazard in uranium mines, to invest resources for assessing a lesser hazard to a greater degree of precision was not cost effective. (iv) Since gamma dose rate is related to ore grade, individual doses could be assigned from knowledge of work location and ore grade. Before deciding which of these options would be most appropriate, it was necessary to have some idea of the magnitude of the problem. Very few data were available in the literature and with the exception of a few spot dose rate measurements, and the results of a few gamma dosimeters issued to selected individuals by some of the mining companies, nothing was available. A rule of thumb of obscure origin is often quoted within the industry indicating that gamma dose rates underground will be about 0.25 mR/h per lb/ton or 5 mR/h per % U. This had been used by some to justify neglecting gamma radiation at least for ore grades of the order of 0.1% or 2 lb/ton, on the grounds that gamma dose rates would be of the order of 0.5 mR/h and therefore give rise to annual doses of only about 10 mSv (lrem). That is, it was assumed that gamma radiation was of limited concern compared to the hazard associated with the inhalation of radon daughters. We were thus faced with the situation of just assuming that no regulatory limits were being breached. This situation could not be allowed to continue. A program was initiated to investigate the gamma doses absorbed by uranium miners in three mines in Ontario, and extensive gamma surveys were conducted in the Quirke 2 mine of Rio Algom Ltd, Elliot Lake; Denison Mine, Elliot Lake; and Agnew Lake Mine, Espanola. Negative reaction was received from several mine company officials to the possibility of all miners being required to wear personal gamma dosimeters due to the logistical difficulties involved, and therefore part of the project was aimed at determining if a reliable correlation between gamma dose rate and ore grade in the work location could be deduced, in order that dose rate times time calculations might be used for gamma dose assessments. The results of these programs provided evidence that the gamma dose for some employees in the three mines investigated may be a significant fraction of the current maximum permissible annual dose of 50mSv (5 rem). When combined with radon daughter exposures in the manner recommended by the ICRP at their 1980 Brighton meeting (ICRP 80) the results indicated that some individuals will come close to the resulting limit and may even exceed it. The results also indicate that is probably not feasible to develop a reliable formula for

Jan 1, 1981

By Filipe de Menezes Torres, Augusto Pereira de Sa, Itavahn Alves da Silva, Eliana Ferreira Rodrigues, Carlos Antonio da Silva, Varadarajan Seshadri

Top slag eye opening which happens as a result of gas injection is a function of the gas flow rate in addition to other factors such as ladle geometry, porous plug location as well as slag properties. Slag eye opening leads to entrapment of atmospheric nitrogen, oxygen by the steel melt affecting adversely the steel quality. In this work aspects of mixing and eye formation in steel making ladles with inert gas injection have been analyzed through physical and mathematical modeling techniques. Influence of ladle, gas flow rate and distribution and slag properties has been assessed. A correlation for estimating eye opening has been developed. Results from PIV measurements and images of eye opening obtained using a camera have been utilized to validate results from CFD simulation.

Jan 1, 2015

By M. A. Ouederni, G. C. Chorosz, E. P. Déliac

This paper deals with the heat flow problems in deep workings (depth greater than 1000 m in France). The approach benefitted from experience gathered in France and South Africa. Deep mines are located in the East of France (coal in Lorraine and potash in Alsace), where the geothermal gradient can reach 4 'C per 100 m (Virgin Rock Temperatures, VRT, around 50 'C). This paper is concerned with the following topics: method of studying the heat flow problem on a mine-wide basis, specific models for heat and moisture pick-up, interfacing of heat and ventilation calculations and a case history in the Lorraine collieries. The heat flow problem on a mine-wide basis is studied in a fashion similar to ventilation networks. Each branch is considered as a "black box" where the air picks up heat and moisture (or is cooled, in the case of an air-cooler). Each box is therefore modeled as a heat transfer unit, hence the calculation of outlet temperatures (wet- and dry-bulb) from the intake ones. The whole network can thus be computed as a sequence of boxes from the air intakes towards the outlets. The second section reviews a number of models used for the assessment of heat and moisture pick-up in the "boxes", with emphasis on stopes and development ends, which are particular to the mining method in use. Two types of stopes are considered: longwall (horizontal and inclined) and cut-and-fill (subvertical). Mechanized rock breaking and blasting can be accounted for. A particular attention is given to development ends, especially complex from the heat flow point of view (rock characteristics, wetness factors, etc.) and usually quite hot. These workings, which are critical in order to secure new production areas, are studied on an average basis as well as in extreme conditions. The calculation takes into account the history of rock temperatures. The interaction between ventilation and thermodynamic calculations is still under development. The idea consists of coupling ventilation calculations with the "box" models: the first step determines the direction of air flow, hence the sequence of the boxes; thereafter the calculations yield the effect of temperature and presssures on air flows. The final section reports on the validation of the whole approach against field data. It concerns several heat flow surveys aimed at checking the models for shafts, stopes and development ends. The accuracy of the method is found very satisfactory.

Jan 1, 1987

By H. Fujihara, K. Uesugi, H. Toda, A. Takeuchi, K. Shimizu

"Hydrogen is trapped at a variety of microstructures, for example grain boundaries, dislocations and particles. It is thought that hydrogen trapped at trapping sites is redistributed to the other sites under loading and then brittle fracture occurs with hydrogen accumulation. In order to understand hydrogen embrittlement behavior, it is necessary to investigate the time evolution behavior of hydrogen accumulation at each trap site. In the present study, changes in hydrogen distribution are observed under stress using Kelvin force microscopy (KFM) that can visualize hydrogen concentration distribution on material surface at high resolution. Spot-like hydrogen enriched regions are observed on the surface of a material. In addition, hydrogen depleted regions are observed around those enriched regions, and the appearance of hydrogen trap due to particles existing near the material surface is revealed. On the other hand, hydrogen trapped at grain boundary can be visualized. From in this result, it was suggested that crystallographic factors influence hydrogen accumulation. The relationship between initiation and propagation of intergranular crack and hydrogen accumulation under stress will be discussed.INTRODUCTIONHydrogen present in a metal sometimes has significant effects on various properties. Hydrogen in a metal is trapped at a variety of microstructure, for example dislocations and grain boundaries. Grain boundaries, dislocations and micro pores are the major trap sites in aluminum alloys. Some researchers considered that hydrogen redistribution and accumulation between these trap sites in a material with loading plays an important role in the brittle fracture behavior. In general, in intergranular fracture and quasi-cleavage fracture, the hydrogen trapped at grain boundaries and dislocations contributes to fracture behavior, respectively. Recently some researchers have shown that the ductile fracture in aluminum alloys is resulted from growth and coalescence of hydrogen micro pores. Analysis using first principles calculation indicates that intergranular fracture occurs when hydrogen concentration reaches 20 atom H/nm2ongrain boundary. From this report, it is considered that hydrogen redistributed during deformation accumulates locally in order to cause hydrogen brittle fracture. In order to understand hydrogen embrittlement, it is necessary to investigate the time evolution behavior of hydrogen accumulation at each trap site. In the present study, we evaluate the relationship between hydrogen accumulation behavior and fracture behavior in Al-Zn-Mg based alloys. In-situ observation was made by combining the tensile test with Kelvin force microscope (KFM) that can visualize the hydrogen concentration distribution on the material surface with high resolution. We also investigate the relationship between hydrogen distribution behavior and crystal orientation."

Jan 1, 2018

By J Aydin Bilgin, Sedat Esen

This paper describes the ideality of some commercial explosives with the help of the detonation theory and detonation velocity measurement. Ideality of an explosive can be determined by comparing experimentally measured and ideal detonation velocities. A measured detonation velocity at a certain charge diameter markedly lower than the ideal value indicates incomplete reaction and thus non-ideal detonation. Since it is shown that commercial explosives exhibit non-ideal behavior, two-dimensional detonation theory should be used to evaluate the performance of explosives. This theory enables to compute the detonation properties of explosives (detonation velocity, detonation pressure, etc.) as a function of charge diameter and confinement. The use of the one-dimensional detonation theory to compute the detonation properties for commercial explosives has an error associated with it as these calculated properties are independent of charge diameter and confinement. It assumes that shock front is planar. Hence, it is incapable of assessing the ideality of the explosives due to its assumptions. Shock front in real situation is curved in shape but not planar as in one-dimensional detonation theory. In this paper, the non-ideal behavior of some commercial explosives is modeled using EXRINT code based on the steady-state two-dimensional detonation theory firstly. Then the degree of ideality of each explosive found from the code is checked using detonation velocity test results conducted at a quarry. It has been shown that idealities of the tested explosives determined by the code agree well with the field detonation velocity test results.

Jan 1, 1999

By Sahendra Ram, Priyadarshi Onam, Abhishek Kumar Singh

A numerical simulation study is carried out for assessment of stability of coal pillars having dirt bands by varying its size and depths. Physico-mechanical properties of dirt bands including thickness and its position in pillar system are varied in the simulation study. Results of the simulation study are correlated with the available empirical approaches of pillar strength are validated with field observations. It is observed that the presence of weak dirt bands significantly influences the strength of pillar. An attempt is made to develop correction factor for the available empirical approaches, which are developed without considering the weak dirt bands in pillar system. The findings of the study will be helpful for suitable design of different size of coal pillars at different depths and stages of depillaring operations.

Feb 1, 2025

By Danielle Nhanqulumanga, Pranith Bhatt, Snehal Patel, Khadeeja Priyan

The Bi-Directional Static Load Test (BDSLT) is a test that determines the capacity of piles when loaded under bi-axial static compression. In recent years the BDSLT has seen an increase in demand due to its safety, speed, and affordability. This innovative foundation testing method has been universally used over the last 50 years, however respective codes and standards have only been published within the recent years. Detailed test procedures and methodology are expatiated in the ASTM D8169 M-18 [1], and the IRC 78 2014 Clause 709.2.5. [2] These standards provide the minimum requirements for the execution of the BDSLT. In this paper we did a comparative study of both standards envisaging to bring attention to the similarities and discrepancies found therein, with an aim to highlight the impacts and challenges that differing provisions of each standard could pose on the conduct of the BDSLT. Discrepancies found have been explained on the basis of geotechnical engineering theories and relevant field occurrences observed by superior engineers. Additionally, we emphasize on the relevance of experienced engineer’s judgement when utilizing the standards.

Sep 1, 2022

By D. W. McGlashan

[Comideha;tion o 4 chyakd- chem and aLtuctund phopetttiu o auRdide nm&, The in~o/uncction gained h ;to be uned ;to iM;tmph& ( I! dnukey bho hen mind-aundacu , ( 2 ) modidicakio~n 06 ;the minmd n~tdacu, and (3) eac;tiom at ;the mind adac fnom ;thu e baic din oipfina, concep;tc, wLth hegattd ;to .the changen kha;t awtgacu undehgu, heac;tiom kha;t might take place, ,the geom&y 04 ;the inkmduce, ;the nkde 04 diddmenk &om and iom in ;the intmdace, and okhm phyaicd and chemicd pttopemXu od an intmdace mun;t be developed, weighed and appfied. The au/tho~ ded wah thue concep;tud connidmatiom @om which hypokhuu me n& ko denchibe khe envhomenkd-ivttadaciae hela;tiomhipa doh nevmd nddide minettah, The ch&enge and moltivation in khe hu eattch h in a henhe a deattch doh baic dad and helcctiomkipa needed doh accompfi he&.] INTRODUCTION Qualitative and quantitative explanation of particulate solid separations are unknown entities because of the lack of adequate models and mathematical relationships to explain the activity occur- ring between the solid and liquid phases. It is a transitional region in which it is difficult to ascertain the mechanisms of adsorption of ions, molecules, etc. on mineral surfaces, as well as other secondary reactions which occur in interfacial regions. Thus, in this paper the authors deal with conceptual considerations from which hypotheses are set forth to describe the environmental- interfacial relationships for sulfide minerals.

Jan 1, 1968

By Joseph Peterson, Alexander May

The Bureau of Mines used geochemical modelling computer programs to characterize a site containing lead slag generated by a lead processing facility. Tests for toxic elements by the U. S. Environmental Protection Agency (EPA) extraction procedure showed that all elements except lead were in compliance. Concentrations for lead ranged from 28 to 30 ppm. However, analysis of water samples from monitoring wells resulted in no lead concentrations that exceeded the National Drinking Water Standard. A discussion of a computational program to calculate concentrations of lead species and several other ions is presented.

Jan 1, 1991

By K Mayank, A N. Mainza, I Govender, M Narasimha, A Mittal

In mineral processing industries grinding is the most energy-consuming process. A tumbling mill is an essential grinding equipment widely used for particle size reduction. Power consumption, impact forces and trajectory paths are critical parameters for characterising a tumbling mill to determine grinding efficiency. The effect of lifters and mill speed plays a vital role in such parameters. However, most of the studies ignore the impact of the lifter and do not investigate the effect of slurry dynamics on charge motion. The focus of the present work is to prepare a computational model that can accurately predict the complex multi-phase dynamics of charge particles, air and slurry inside the mill using a model that couples computational fluid dynamics (CFD) and the discrete element method (DEM). The details of impact forces with lifter profiles and mill speed variations will be refined even further using the CFD-DEM coupling approach. The slurry-air free surface is modelled using the volume of fluid (VOF) method, and the charge motion is modelled using the DEM. The phases are coupled using the interface momentum exchange between the charge and the fluid slurry. The coupled model is validated against experimental results from the positron-emitting particle tracking (PEPT) data. The validated model compares the effect of slurry content on charge dynamics with the dry DEM model. The presence of slurry is observed to dampen the tangential and shear contact forces.

Aug 24, 2022

By Daniel de la Rosa, Juan Manuel Mayoral, Damián Vital

"This paper presents a numerical study regarding the loads, and the corresponding damage, taken by the primary and secondary lining of a tunnel built in cemented fine-grained stiff soils. This study aims at establishing more rational design criteria that take into account explicity the lining performance. A 3.5 km long tunnel to be built in a densely populated northwest area of Mexico City, was considered as case study. Series of three-dimensional finite difference models, developed with FLAC3D, were used to simulate the tunnel construction, and to compute the ground settlements, internal forces, bending moments, and displacements acting both on the primary and secondary tunnel linings. Interaction diagrams were used to study the lining performance. Several advancement lengths, and tunnel covers were considered to establish their impact on the loads transferred to the tunnel lining. A practice-oriented damage criterion for tunnels was proposed based on the interaction diagram analysis. INTRODUCTION Lining performance during conventional tunnelling, CT, as defined by the International Tunnel Association, ITA (ITA 2009) is strongly affected by the construction procedure. Special attention must be taken in cemented fine-grained materials, such as those found in the northeast portion of Mexico City, due to the potential of fragile failure (i.e. the soil fails suddenly without important deformation) that these soils may exhibit. During CT, it is assumed that the ground strength contributes to the stability of the excavation, as long as the lining is built correctly. It is common practice to consider two structures, which together form the tunnel support: 1) A primary lining, which is a flexible support, which allows excavation walls to deform to mobilize part of its shear strength, and thus contributes to the tunnel self-stability, and 2) A secondary lining. Commonly, the primary lining consists of several layers of shotcrete. In this case the installation method guarantees perfect contact between the lining and the excavation perimeter. The secondary lining, if required, is used to withstand the load conditions in the long term and also has an esthetic function. This paper presents a numerical study aimed at establishing a performance damage criterion for the primary and secondary lining design in cemented fine-grained stiff soils. Due to the lack of data, the strength and deformation parameters were established through empirically-derived relationships. Three-dimensional finite difference models were developed to simulate the tunnel construction, and compute ground settlements, internal forces, bending moments and displacements acting both on the primary and secondary tunnel linings. Interaction diagrams, along with a damage criterion were used to study the lining performance. From the results gathered insight was gained regarding tunnel lining performance during CT."

Jan 1, 2016

By G. Mark Aylmore

Various processes have been developed using a combination of elevated temperature and chemical treatment processing to recover Li from silicate minerals. To facilitate further process development, a comprehensive understanding of the deportment of Li and associated minerals in ore bodies is essential to allow the industry to predict the response of ore reserves to metallurgical treatment options. This paper describes results from the integrated use of the John de Laeter Centre’s state of the art analytical and mass spectrometry techniques to characterise a selection of Li bearing ore bodies and determine their amenability to potential processing options for the extraction of Li. The mineralogy, mineral associations, and liberation characteristics of ore-bearing and gangue minerals were characterised using a combination of the TIMA and XRPD studies. The Li content and distribution within minerals were defined using LA-ICPMS and field emission scanning electron microscopy techniques (EBSD, ToF-SIMS) and atomic probe microscopy.

By F. Segobia, H. Lozano, M. Portal, F. Ysla, L. Goicochea

This case study evaluates the long- term physical stability of various historical mining structures remediated by the Center for Mining Environmental Research and Studies (CIEMAN) in Hualgayoc, Cajamarca, Peru. The region has a long history of mining activity, with remnants dating back to pre-Inca times. CIEMAN has assumed responsibility for remediating 286 environmental liabilities in the area, including adits, shafts, pits, tailings, and waste rock dumps. The study analyzes the methods employed to stabilize these structures, including geotechnical engineering techniques and revegetation. Long-term monitoring results are presented, assessing the effectiveness of remediation measures and predicting the future stability of the structures. This study highlights the importance of responsible remediation of mining environmental liabilities to ensure the safety and sustainability of communities and ecosystems affected by historical mining.

Feb 1, 2025

By G. Sánchez, S. Seiler, B. Klein, T. Cebeci, P. Bradshaw

The Decar Nickel District is a greenfield discovery by FPX Nickel Corp., of nickel mineralisation located in central British Columbia (BC), Canada. The Baptiste deposit is part of the Decar Nickel District and is a unique deposit containing a nickel-iron alloy mineral called awaruite, with over 2-billion tonnes of inferred resource grading 0.12% Davis Tube Recoverable (DTR) nickel. This deposit represents a significant nickel resource. Awaruite is a high density and ferromagnetic mineral, which could be recovered, along with magnetite that is also present in the samples, using magnetic separation. However, there is still a lack of understanding of the properties of the awaruite and its metallurgical response. This information is imperative for the set-up of the variables involved in its concentration. The aim of this paper is to show and discuss the effect of magnetic field strength for the recovery of nickel from Baptiste deposit samples. Magnetic separation at bench and pilot scale with different magnetic field strengths is evaluated as a concentration method for awaruite. Mineralogical information is provided to support the results and also to briefly assess the variability of DTR nickel within the deposit. The Baptiste deposit is unique and will benefit from a sound scientific understanding of the process solution as well as other ongoing work. If successful, the outcome will lead to the development of a mine. With greater than 2-billion tonnes of inferred resource, the mine would represent a significant new source of nickel globally. Keywords: Nickel ore processing, magnetic separation , awaruite, magnetite

Jan 1, 2020

By M W. Chen, I Canbulat, S Saydam, C G. Zhang

The height of fracturing (HoF) measures the propagation distance of continuous fracturing from the mining horizon and is also termed the height of cracking (Hebblewhite, 2020; Khanal et al, 2019) or hydrologically the height of groundwater drainage (Tammetta, 2013). In longwall practice, HoF is an important predictive indicator for assessing the dewatering effect of panel extraction on the shallow aquifer and surface flows. The HoF determination is basically dependent on field measurement works, typically using surface extensometer, borehole televiewer imaging, piezometer monitoring, packer testing, borehole breakout logging, and isotopic tracer monitoring (Brown and Walsh, 2022; Corbett, 2022; Hebblewhite, 2020; Holla and Armstrong, 1986; Mills and O’Grady, 1998; Walsh et al, 2022a, 2022b). These methods or tools have been widely applied to observe rock fracturing and groundwater responses to longwalls at Australian coalmines, for example, Dendrobium Mine (Brown and Walsh, 2022; Walsh et al, 2022b), Appin Mine (Walsh et al, 2022a), and Springvale Mine (Corbett, 2022). In Chinese mines, borehole televiewer imaging and packer testing are more frequently used due to convenient instrumentation, quick testing, and not requiring long-term maintenance of the instrumentation boreholes. The HoF determination also involves further raw data interpretations, for which specialist software for data extraction and quantitative criteria for bounding the fracture transition and termination are necessary. By combining the measured fracture distribution and longwall parameters regarding panel geometry and geological settings, several HoF models have been developed for conceptualising the understanding of strata depressurisation and providing mine engineers fast calculation tools for HoF prediction. The Mackie model considered the height of fracturing as the upper bound of fractured zone and revealed that within the fractured zone there are highly connected fractures and accordingly porosity enhancement and groundwater depressurisation, where the fracture network can be less transmissive from the mining horizon up (Hebblewhite, 2020). The fractured zone shares similar fracturing regime but different heights in varying models: HoF is 30 to 58 times of the mining height (t) based on Australian, Soviet and UK experience (Kendorski, 1993, 2006), and 21 to 33 t according to the field measurements in NSW Central Coast, Australia (Galvin, 2016). Some Australian longwall mines adopt Ditton model (Ditton and Merrick, 2014) (Equations 1.1 and 1.2 in Table 1) sourcing from NSW coalfield experience for HoF prediction, while Liu model (Liu, 1981) (Equations 2.1 to 2.4 in Table 1) developed from 27 coalmines in China is frequently used by Chinese coalmines.

Nov 29, 2022

By Chris M. Haberfield, Neil D. Benson

The assessment of overall modulus (or stiffness) of a fractured weak to moderately strong rock mass is a key parameter in the design of civil engineering works in these materials. It also provides the highest level of uncertainty due to scale effects, anisotropy and the influence of joint frequency and joint stiffness. Using the example of the Melbourne Mudstone, this paper compares approaches using empirical rules based on intact rock strength, laboratory testing, in situ field testing, semi-quantitative assessment techniques based on rock mass classification and back analyses. L'évaluation du module (ou rigidité) global d’une masse rocheuse faible et fissurée a modérément forte est un paramètre principal dans la conception des travaux du génie civil dans ces types de matériaux. Elle fournit également le niveau le plus élevé d'incertitude due aux effets d’échelle, à l'anisotropie et à l'influence de la fréquence et de la rigidité des joints rocheux. En utilisant l'exemple du schiste de Melbourne, cet article compare des approches empiriques basées sur la force intacte de La roche, les essais expérimentaux au laboratoire, les essais sur site, les techniques semi-quantitatives d'évaluation basées sur la classification de la masse rocheuse et les analyses en retour. Die Schaetzung des allgemeinen Steifigkeit-Moduls des gebrochenen schwachen bis zu maessig starken Felsmassen ist eine Haupt- Annahme in dem Entwurf von Tiefbau-Projekten in diesen Materialien. Es verursacht den hoechsten Grad der Ungewissheit in Folge der Groessenordnung, Spaltorientierung und dem Einfluss der Haeufigkeit der Risse und Bruch-Steife. Unter Verwendung des Beispiels des Melbourner Tonsteine, vergleicht diese Darlegung die Anwendung der empirischen Regeln, die sich auf die Staerke des ungestoerten Fels Basieren mit Versuchen in der Material Pruefungsanstalt, Untersuchungen auf der Baustelle und halb-quantitative Schaetzungsverfahren, die sich auf die Felsmassen Klassifikation und fruehere Analysen stuetzen.

Jan 1, 2003

By Sibabrata Patnayak

A major problem during shovel excavation in oil sand mining is the variability of material diggability resulting in varying mechanical energy input, cycle time, energy consumption, wear, and stress loading of shovel dipper-andtooth assembly. This variability greatly influences the mining equipment performance. Different approaches such as empirical ground classification systems, analytical methods, and performance monitoring that are used to determine diggability of groundmass are reviewed. It is concluded that the existing empirical diggability classification systems are site specific and mostly based on rock and therefore, cannot be used for shovel excavation in oil sands. The O&K wedge test is a simple and useful index test for establishing correlations between cutting resistance and geotechnical properties of coal and other soft rock overburden material. But this test, when performed on small size unconfined oil sand samples, may not give reliable indication of diggability because of the boundary conditions on the specimens. Digging predictions made using analytical and laboratory digging models need to be verified with performance monitoring data to better understand the digging effort in oil sands.

Apr 1, 2005

By Donald D

A number of standard tests are conventionally carried out to characterise strength properties of rock. The values of the parameters obtained are often affected by planes of weakness or defects in rock structure. For the purpose of mine design, the range in values or the class of the strength (obtained from a number of tests) is generally more important than a precise value (obtained from a single or limited number of tests). Research has been conducted to establish a relationship between an indentation index and the strength of the intact rock material from the Eastern Goldfields of Western Australia. The Tamrock Raise Boring Index (RB-i) test, which is quick and easy to perform, was selected as the indentation test. The results show that, for heterogeneous, strong to very strong rock, there is a good correlation between the indentation index and the uniaxial compressive strength and tensile strength.

Jan 1, 1996