Search Documents

By John E. Litz

The Denver Process is a chemical/metallurgical process for treating radioactive or mixed wastes by extraction and concentration of the radioactive and/or hazardous component(s). The process was developed at bench scale, evaluated at pilot scale, and will be implemented at full scale to remediate a low-level radioactive sludge. Six unit operations comprise the process: feed handling, leaching, solvent extraction, electrodeposition, precipitation, and tailing preparation. Unit operation design may be modified to tailor the process for varying feed stock composition. Radioactive or mixed waste is reacted with aggressive reagents in an aqueous phase, solubilizing targeted components. These components are then selectively extracted and concentrated in subsequent steps. Waste solids and solution exit the process as non-hazardous non¬radioactive waste. Dehydration of aqueous waste by submerged combustion eliminates aqueous discharge.

Jan 1, 1994

By John T. Wizzard, R. P. Killmeyer, B. S. Gottfried

The Coal Preparation Branch of the Pittsburgh Energy Technology Center has developed a computer program to calculate the performance characteristics of coal washing devices. This program uses specific gravity analyses of the clean coal and refuse streams as input, and generates dependent and independent performance criteria for the washer. Partition curves are internally represented in a functional form by a Weibull function. Performance criteria generated by this computer program are compared to manually calculated performance criteria for air tables, Dynawhirlpools, Baum jigs, hydrocyclones, and dense medium cyclones. The comparisons show that the computer program gives results in close agreement with the hand- calculated values while greatly reducing the amount of time involved in performing the analyses.

Jan 1, 1983

By D. R. Keck

"SINCE the .Canadian Chemical Company has no direct connection with mining operations, and I have had no experience with mining, there is little I can tell you that you do not already know. However, we have had considerable experience with certain types of metallurgical problems and I would like to discuss with you some of these problems and their solutions by our metallurgists.In order to acquaint you with the type of plant and processes to be employed at Edmonton, I would like first to take a few .minutes to trace briefly the history -of the Canadian Chemical Company's affiliate, The Celanese Corporation of America. In the early •part of the twentieth century, two young Swiss brothers, Camille and Henri Dreyfus, received their P.h.D. degrees in chemistry. They were extremely interested in work which was being carried on at that time to find a suitable synthetic fiber that could compete with natural fibers, both quality and price-wise. Early man-made fibers were both coarse and hard to dye. The Doctors Dreyfus• poured all their earnings into research and ultimately developed cellulose acetate filament. During World War I, the Dreyfus brothers were invited to the United States to produce cellulose acetate 'dope' for airplane wing coverings. Dr. Camille Dreyfus built the first American plant for fiber production at Cumberland, Maryland, in 1924.Due to resistance of textile mills to the new fibers, Celanese was forced to set up its own dying, weaving, and finishing mills to prove the new materials. Through the years, however, this operation has •been retained primarily for fabric development purposes,.. with the majority of the acetate being sold to other textile mills."

Jan 1, 1953

By Oscar H. Lentz

During 1960, the controversy over percentage depletion reached the level of debate between presidential candidates. Nixon took the position that he would not tamper with the status quo in this matter. Kennedy took the position that he was willing to take a fresh look at the issues involved. Kennedy's position appears to have been based upon two premises: (1) new sources of federal revenue may be needed; and (2) current depletion rates, even if sound in principle, may be too high and, therefore, inequitable. The latter premise constitutes the basis for the claims that depletion allowances are simply "loopholes" of tax avoidance. Very probably the controversy over percentage depletion will remain in the political limelight during most of the coming decade. It is quite possible that the current depletion rates, at least those for oil and gas, will be reduced during this period. The aim of this paper is to isolate the complex causes of this mounting opposition to percentage depletion.

Jan 1, 1961

This paper reports on the behavior of mercury and its compounds during the thiosulfate leaching and recovery of gold. Thiosulfate solutions are shown to dissolve Hg0 and Hg2Cl2 to a similar extent as cyanide, but the leaching of HgS is significantly slower in thiosulfate solutions compared to cyanide. Hence, the use of thiosulfate may be an option for treating ores containing high levels of cinnabar, especially since the legislation concerning the discharge or sale of mercury is becoming more restrictive. The deportment of mercury during gold thiosulfate loading and recovery using a strongly basic anion-exchange resin was also studied. Although the mercury thiosulfate complex loads on the resin, the adsorption is weaker than for gold, with an equilibrium constant between gold and mercury of 51. Resin loaded with gold, mercury and copper was pre-eluted with thiosulfate (to remove copper) and eluted with a chloride and sulfite eluant. The majority of the mercury is eluted by the eluant and, hence, its deportment closely follows gold and the eluate would need to be treated to remove either mercury dur-ing or prior to gold electrowinning.

Jan 1, 2010

By P. M. May, V. Gella

The deportment and speciation of trace elements during mining and minerals processing is becoming an area of increasing concern with regards to potential health and environment risks. The use of chemical modelling can enhance our basic understanding of the deportment and speciation of trace metals under conditions present in gold processing solutions, and assist in laboratory and field investigations. In this paper, we report the results of chemical speciation modelling using the JESS software package for the trace toxic elements Pb, Cd, Hg, Se and Te in cyanidation solutions of varying salinity and relate the models to experimental data. The speciation of mercury is examined in detail.

Jan 1, 2011

By Leah Penner, Thomas J. Ruth, Paul Schaffer, François Benard, Edouard Asselin, Stefan K. Zeisler, Thomas J. Morley

"This paper details the electrodeposition of metallic molybdenum from an aqueous, acetateelectrolyte containing molybdate ions. The deposition is carried out in a highly concentrated (up to I 0 M) acetate bath in the presence of a very low concentration of bone glue (60 µg/L). The molybdenum metal deposits are up to 20 µm thick and adherent. The deposits were characterized by XRD and XPS analysis. The deposition process is very inefficient, as up to 99% of the current is used to generate hydrogen during electrolysis. The effect of acetate concentration, pH, additives and current on the deposition efficiency and physical properties of the molybdenum deposit were investigated and optimized to obtain smooth, adherent coatings.IntroductionMolybdenum has increased thermal and wear resistance properties that are often utilized in material coatings [I]. These coatings are most often manufactured by sintering, pressing or spraying molybdenum powder at elevated temperatures, as a substitute method for standard metallurgical practices, such as electroplating [2, 3]. The lack of reports describing molybdenum deposition is most likely due to the highly oxophilic nature of molybdenum and the stability of its oxides, especially in water. Previous attempts to electrochemically reduce molybdenum from molybdate (Mool·) ions to molybdenum metal have reported the production of either a poorly adherent mixed oxide [4-6], or a thin(< 0.1 µm) metallic film [7-9]. Thick metallic molybdenum is capable of being co-deposited with one of the iron-group metals (Ni [10], Co [11] and Fe [12]) to produce an alloy [13, 14]. These alloys, however, may not be suitable for applications requiring pure molybdenum as they usually contain less than 50% molybdenum (often less than 30%)."

Jan 1, 2012

By J. B. Knaebel, M. W. Von Bernewitz

OUTSTANDING FACTORS that have largely induced the current great interest in the reopening of old mines and the search for new deposits are the increased relative value of gold, the certainty of a market for it, and the decreased activity and poor profits in other lines of endeavor. It is easy to understand why a miner out of a job and unable to find any other means of livelihood would naturally take to the hills with his pan, pick, and shovel; but never before have inexperienced, would-be prospectors and placer miners materialized from the factories and farms, the haberdasheries, and the oil and gasoline supply stations, in such numbers as the last couple of years have witnessed, except when rich strikes of the proportions of a Klondike have been made. What, may one ask, has occasioned this condition? Unemployment has put these men in a receptive frame of mind, and newspaper and magazine articles have done the rest-- The Gold Miner of Los Angeles (a new weekly), The Mid- Week Pictorial (New York) for Sept. 3, 1932, and Popular Science Monthly for August, 1932, for instance. Even the Saturday Evening Post had an article on a promising part of Colorado. Stories that good wages may be had for the panning in nearly every western state have been featured by daily papers, popular "scientific" magazines, and quasi- technical journals. These tales have been eagerly grasped by thousands of people whose ignorance of mining has only served to increase their enthusiasm.

Jan 1, 1932

By J. G. Patterson

"The depressive action of sodium cyanide on chalcocite has been investigated and found to be unstable. Flotation results show that with the addition of sodium cyanide to the system chalcocite is initially depressed but rapidly recovers with time, provided there is sufficient oxygen present.lt is proposed that the unstable depression is due to the reaction of cyanide with adsorbed xanthate and copper ions at the chalcocite surface to form soluble copper complexes. When all the free cyanide has so reacted, xanthate anions can then re-adsorb on the chalcocite surface and the flotation will recover. Results are presented to verify the the above mechanism."

Jan 1, 1968

By Benjamin H. Clark

"For over 50 years, Derrick Corporation has been renowned for its innovative and durable fine screening equipment and screen surface technology. Derrick’s latest innovation, the patented Stack Sizer, offers mineral processors both high tonnage capacity and high separation efficiency on an extremely small footprint.The Stack Sizer is suitable for separations from 6.3 mm down to 75 microns (200 mesh). The Stack Sizer, coupled with Derrick’s patented urethane screen surface technology, offers an extremely economical alternative to hydraulic classifiers, hydrocyclones, and less efficient low volume wet screening systems. Stack Sizers have been used in feed preparation for flotation, spirals, and a variety of jigs. Mineral processors wishing to reduce grinding circuit circulating loads and generation of slimes due to over grinding, thereby enhancing the efficiency of flotation and gravity circuits, now have another technology at their disposal to perform this critical sizing and grade control function.Over 200 Stack Sizers have been installed in numerous mineral processing applications worldwide attesting to the rapid acceptance of this technology. Stack Sizers are currently screening ferrous and non-ferrous metal ores, mineral sands, silica sand, kaolin clay, feldspar, garnet, phosphate, aluminum dross, potash, coal, tantalum, spodumene, niobium, and other rare earth mineral ores.INTRODUCTIONDerrick engineers have long understood and demonstrated the importance of screen width in coupling both high capacity and high separation efficiency for fine wet sizing applications. As opposed to fine dry sizing, where the length of the screening machine is critical for high separation efficiency, introducing slurry feed to screens in a thin and even layer at minimal velocities across wider screen surfaces allows for high capacities and efficiencies, with maximum screen cloth life. This is due primarily to the combination of free liquid and high frequency vibration of the Derrick motors, which allow fine undersize material to pass through the screen apertures. Lacking either of these factors would be extremely detrimental to the screening process. Without the high frequency vibration of the motor, the screen is essentially a low efficiency sieve bend. Without the free liquid to carry fines through the screen openings, the screen is for all intents and purposes a glorified conveyor or dewatering unit, as little or no sizing takes place once the screen is devoid of free liquid. For optimal screening results, Derrick recommends feeding slurry to a screen at approximately 20% solids by volume. Figure 1 shows the Stack Sizer design concept. Note that a single feed point is used to evenly distribute the flow to the five separate feed points."

Jan 1, 2007

By A. W. Allen

THE technological study of the treatment of gold and silver ores has been largely responsible for the phenomenal strides which have marked the progress in this branch of metallurgy during recent years. In no other application of science to industry is system more imperative at every stage; correct formulation of result is only second in importance to efficiency of operation. Progresss in method has been largely the result of individual initiative, aided by the work of technical journals and metallurgical societies. There still remains a field for profitable discussion, and it is my intention to deal with some inconsistencies of expression common to a number of writers on the subject; and also to draw attention to the false impressions created by a statement which may, possibly, be only unintentionally misleading. I also take the opportunity of tracing the source of both metallurgical and economic result; and to question the desirability of the methods usually employed in arriving at a final statement. In the first place, I wish to deal with the question of extraction. This term may mean anything or nothing, and it is often used to mislead. In a report of a mining engineer as to the result of operations subsequent to the remodeling of a treatment plant prominence was given to the statement that the extraction had amounted to 91 per cent. On examination it was found that only a small percentage of the so-called extraction was calculated on actual bullion return, a proportion being figured from the gold left in the zinc boxes, and not recovered. In addition to this, a proportion of the extraction was said to be due to gold in concentrate. As there was no concentrating apparatus on the property and as concentration did not form a part of the scheme of treatment the matter was investigated, with the result that the concentrate, of lower gold content that the original ore, was found to be the result of an inefficient pumping system which failed to provide for the whole of the battery product delivered to it. The balance was stacked and, although itself of no marketable value, the gold content was allowed to form a basis of extraction figures.

Jan 7, 1914

By Mike Faure

Hercules cribs make use of timber loaded parallel and perpendicular to the grain. Maximum use is made of the orthotropic properties of timber resulting in crib- having superior strength, high initial stiffness and controlled post yield deformations. Blocks and timbers can be combined in many different ways resulting in thousands of different geometries. Each geometry has a specific combination of block on block, timber on timber and block on timber contact area which results in a unique performance. Each crib can be fingerprinted by defining four parameters relating to its load/deformation curve. If the geometry is known, the performance can be predicted with a high degree of accuracy. If the mine support requirements are known, the crib geometries can be designed which met theme requirements in the most cost effective manner Hercules cribs come closest to satisfying mine support requirements. Due to the flexibility of the concept and their superior strength, they can be employed in most mining situations to enhance safety, improve productivity, reduce working costs or improve profitability.

Jan 1, 1993

By Dennis Arthur Fenton

The hydrodynamic bearing was first described by, Reynolds in 1886, and has since been widely applied in motors, engines, compressors, hydroelectric turbines, and other machinery. For various reasons, the hydrostatic bearing currently predominates in the large, horizontal rotating machinery field (e.g. grinding mills). However, the current industry trend towards increasing size and energy efficiency has resulted in renewed interest in the advantages of hydrodynamic bearings. These advantages include structural improvements, reduced bearing friction, improved bearing life, improved transient characteristics, and reduced lubricant pump size and power requirements. In particular, the higher energy efficiency results in substantial savings on large machines. This paper describes some aspects of the design of large hydrodynamic bearings based on thirty years, of experience in the design of such bearings on grinding mills ranging in journal size from 2.1 m to 6.4 m, see Table 1.

Jan 1, 1985

By D Dickson

The properties along Ida Avenue in Mosman stand 10 m above the road on an outcrop of Sydney sandstone. Access to the houses is generally via a long steep staircase. The owner of 22 Ida Avenue identified an opportunity to use the natural strength of the rock beneath his property to excavate an underground garage and to provide access to the basement of his property via a 10 m elevator shaft from the back of the garage. This paper will describe the design and construction of this unique and innovative urban development.

Jan 1, 2008

The four major contracts for the construction of Museum Station are: 1) Installation of Soldier Piles, 2) Structural Contract including the temporary support, 3) Architectural Finishes which include Electrical and Mechanical Services and 4) Supply and Installation of lifts and escalators. Specific areas of interest include the fabrication, installation and removal of temporary support steelwork, the monitoring of ground loading, and the interface between the structure and. the temporary support. The information collated during construction confirmed the design assumptions and criteria. No major changes&apos;were required in the design of the construction methods. The open cut excavation and construction of this major structure in an inner city area was significant by any standard and was successfully completed with minimum disruption to the public and without damage to adjoining or surrounding property.

Jan 1, 1981

By J. A. Yeats

This paper describes the loading to 25MN of a 1.2m diameter bored cast-in-situ test pile founded in the Thanet Sand which was base grouted. The pile was sleeved over the major portion of its length to test primarily the base response of the pile. The results are presented and compared with similar pile load tests in Thanet Sand.

Jan 1, 1989

By Mohamed A. Younis, Robert J. F. Goodfellow

This paper investigates the design approaches taken and the philosophy employed during the construction of the Metropolitan Airport Commission (MAC) storm tunnels, part of the Phase 4 Segment of the MAC Trunk Storm Sewer Project at Minneapolis St.-Paul International Airport, located in Minneapolis, Minnesota. URS Corporation was retained to provide a design and Construction Management (CM)services for the MAC Trunk Storm Sewer Project. A case history of the design and construction challenges of the project is presented. The MAC storm tunnels consisted of the construction of twin 10-foot inside diameter (I.D.) tunnels within 7 feet of an existing 72-inch I.D. storm pipe at the base of a 70-foot high highway embankment. The analysis required during the design stage of the project is discussed. This analysis and our design approach provided a defensible framework and justification to make design decisions on relevant issues including: allowable spacing of new and existing structures; preferred order of construction; expected ground deformation behavior; response of lining types to adjacent construction; and effects of proposed changes to design at the submittal stage and during construction.

Jan 1, 2003

By A. Aly Selim

A computer model was developed to calculate the fragmentation cost for in situ leaching operations as a function of the blast design and deposit parameters. The model is based on blasting an ore zone only or an ore zone plus overburden by either a coyote blast or a vertical blasthole system. The model calculates the blast design parameters and the fragmentation cost based either on a user input powder factor value or on a powder factor calculated by the model as a function of the overburden height and the ore zone thickness. Examples of blast design parameters calculated by the model are the number and spacing of blastholes for a vertical blasthole system and the number and spacing of crosscuts for a coyote system. The model also calculates the total amount of explosives, the detonating cord length, and the number of primers. The cost of blasthole drilling can be calculated by the model based either on purchasing and operating a drill or on a user input value of the contracted cost of drilling. Application of the model to an example ore deposit showed that the vertical blasthole systems were more economical than the coyote system when there was no overburden and the deposit had an average ore thickness less than 45 meters. With no overburden and ore thickness greater than 45 meters, the vertical blasthole system was either more or less expensive than the coyote system depending on the number of levels used in the coyote system. With overburden, the coyote system was less expensive than the vertical blasthole system for blasting either the ore only or the ore plus the overburden. A coyote blast will usually produce larger particle sizes than a vertical blasthole system. Larger particle sizes can result in lower copper recoveries so that a less expensive coyote blast may not improve the overall economics of an in situ leaching operation. Blasting the ore zone only was generally less expensive than blasting the ore plus the overburden by either blasting system. Also, for the example considered, the coyote system costs were less sensitive to changes in overburden thickness and powder factor while the vertical blasthole system costs were less sensitive to changes in ore thickness.

Jan 1, 1977

By Brady KT, Pattenden G

A laboratory size solvent extraction apparatus has been constructed, which incorp- orates three stages of countercurrent extraction, followed by two stages of counter- current stripping. The model uses a gravity flow system from one stage to another and air lift pumps to recirculate organic and aqueous phases. A novel pump/mixer system is used to transfer solutions from the mixer compartments to the settler compartments. The model has proven valuable in the teaching of solvent extraction principles.

Jan 1, 1984

By Bluhm S. J, Feio L, Ramsden R

A new mining area at the Vaal Reefs gold mine is to have a shaft. system which will extend to a depth of 4 200 m and will require 130 MW of cooling. A novel feature of the proposed cooling system is a large underground air cooling installation in which an ice slurry is sprayed into the ventilation air. The design of the ice slurry bulk air cooler, in the form of counter.flow cooling towers, is discussed. Comparative thermal tests with cold water and ice slurries (with ice mass fractions up to 22 per cent), were carried out in a 5 m high test tower. The presence of the ice in the water spray increases the resistance to heat flow and reduces the overall thermal characteristics of the air cooler by 8 per cent. Notwithstanding this, the use of ice slurries is indeed beneficial in terms of overall costs. It is concluded that a 25 MW air cooler should use 410 kg/s of ice slurry with a 10 per cent ice mass fraction to cool 550 kg/s of air which is 75 per cent of the total air flow rate.

Jan 1, 1988