Search Documents

By Graham Farquharson, Jame Marshall

"Mining towns have always been an important part of Canadian geography. Many Canadians grew up in them. The frontiers of northern Canada would be a lot closer to the United States border but for the pioneering of new mines, new towns, and new transportation routes. Names such as Labrador City, Chibougamau, Val d’Or, Rouyn-Noranda, Kirkland Lake, Timmins, Sudbury, Red Lake, Thompson, Flin Flon, Yellowknife, Whitehorse,Trail and Kimberley are some of the better known larger communities that have grown to become major commercial and government centres, but which started as the base for a mining development.Many other smaller towns never grew beyond being small communities, dependent upon the local mine and many of these are still alive, but perhaps not quite what they used to be. In this list would be Buchans, Schefferville, Chapais, Cadillac, Virginia town, Lynn Lake, Uranium City, Pine Point, and Keno Hill.Nevertheless, all these towns and dozens more like them were residential communities where people lived and raised families and were quite accustomed to being days from the major centres of Montreal, Toronto, Edmonton and Vancouver, and not just hours away as wet end to measure travelling time today."

Jan 1, 1996

By THOMAS LEONBRD WATSON

INTRODUCTION. IN a paper read by title at the Washington meeting of the Institute, May, 1905,1 discussed at considerable length the geological relations, node of occurrence, and the genesis of the lead- and zinc-ores of the Virginia-Tennessee region. The present paper treats of the purely economic phases of the zinc-ores of the district; such as methods of mining the ores, their preparation and treatment. The Albemarle county mines and plant were discussed in the paper referred to above, and will not be considered here. METHODS OF MINING. Until very recently the mining of lead- and zinc-ores in Virginia was limited wholly to the surface belt of weathering. The mode of occurrence and the character of the ores to be mined were such as to demand the employment of methods used in mining secondary concentrated ores. Accordingly, a system similar to that practiced in mining brown iron-ores was employed, being modified to meet the changed conditions. Oxidized or Soft Ores.-Up to the present time practically all the ore mined in the Virginia district has been of the oxidized or soft type;-the silicate, calamine, and the carbonate, smith-sonite; largely the former, which has been localized and concentrated at only slight depths below the surface. Because of the extreme irregularity with which the limestone weathers when stripped of the overlying residual clay, it presents a roughened surface of large and small irregular "chimneys"

Mar 1, 1906

By J. Dubinski

This paper describes the key circumstances of the underground coal gasification (UCG) process, which is planned to be carried out in the Polish hard coal mine ?Wieczorek?. The construction and field tests of a UCG pilot plant have key issues that need to be addressed to realize the research project goal: the elaboration of a highly effective technology of fuel and electricity production. The project will conduct several monthly tests of gasification in the pilot geo-reactor, which will be constructed based on the results of laboratory tests. The realization of the process requires numerous appropriately prepared actions adjusted to natural conditions in the hard coal deposit. Based on scientific principles, it is necessary to elaborate the procedures related to the location of the UCG installation (including its legal and safety aspects), and to perform a technical risk analysis. In addition, it is necessary to determine the required mining, geological, technical, economic and organizational circumstances, while at the same time considering the real but constantly changing process conditions.

Aug 1, 2013

The Ministry of Commerce has been carrying out an evaluation of the resources of the Northwest Nelson region. In part this was to revisit the issues covered in the earlier proposal to close part of Northwest Nelson to mining under section 24 of the Mining Act (1971) initiated in 1990. In addition, the option of using GIS to integrate a variety of spatial data sets to aid policy formulation could be tested. The Northwest Nelson assessment would be a useful trial. The subsequent national park proposal provided a major impetus to the project and resulted in the scope of the study being broadened to include all energy and minerals resources.

Jan 1, 1993

By W. Hustrulid

In the mid-to-late 1800’s the U.S. mining industry was on the threshold of nearly a century of golden times. Nearly every state had a prosperous and growing mining sector. The importance of the industry was reflected in the creation of the state school of mines. Today, with the depletion of readily available mineral reserves, much of the U.S. metals mining industry is considered to be in a sunset phase. The same is true with the mining schools that serve the industry. However, the United States is still a major consumer of the world’s minerals and requires a dependable supply of both minerals and minerals professionals. In his 2002 Jackling Lecture “You Can’t Make a Silk Purse Out of a Sow’s Ear” the author presented a list of concerns, propositions and recommendations. In this follow-up paper, the author further explores the subject through the presentation of a detailed case example focusing on the iron mining industry of Minnesota and minerals education at the University of Minnesota.

Jan 1, 2004

By W. S. Dyer

The Minto coal basin lies in the central part of the province of New Brunswick, near the head of Grand Lake. The village of Minto which is the centre of mining activity of the district, lies about 35 miles east of Fredericton and somewhat greater distances to the north and west of the cities of St. John and Moncton respectively. Although coal has been mined in the basin for a number of years, it was not until recently that the production became sufficient to warrant a thorough geological investigation. The summer of 1922 was spent, in accordance with in structions from the Director of the Geological Survey, in making a detailed study of the geology and coal resources of the Minto coal basin, which is covered by the Minto and Chipman map sheets, each embracing an area of 200 square miles. The present paper is a short outline of the principal results obtained in the field. The writer wishes to acknowledge the assistance cheerfully given him by the managers and officials of the various companies operating in Minto. He wishes especially to thank Mr. W. B. Evans, Manager of the Rothwell Coal Company, for assistance in the collection of fossils and for the generous supply of information relative to the early history of the coal field.

Jan 1, 1924

By Pierre de P. E. M. Ricketts

HAVING had occasion while in Europe during the past summer to visit some of the foreign mints and assay offices connected with the same, I thought a brief description of the general process of coining employed, and such items connected with assaying as were new, might prove interesting to the Institute. The principal foreign mints are: the Royal Mint, London; and the mints in Paris, Brussels, Utrecht, Berlin, Vienna, Copenhagen, St. Petersburg, Stockholm, Madrid, Milan, Rome, and Constantinople. My time only permitted my visiting a few of the principal and largest given in the list, and for a description of the remainder I am indebted to the kindness of Mr. James M. Napier, who in company with the deputy master, and chemist of the Royal Mint, made a complete inspection of all the European Mints in 1870.

Jan 1, 1876

By Peter W. Lipman

Structural and topographic relief in the Sangre de Cristo Mountains of northern New Mexico provides a remarkable cross section through the recently recognized 23-26 m.y.-old Questa caldera and cogenetic volcanic and plutonic rocks. Although largely eroded, remnants of an ash-flow sheet of silicic-alkalic rhyolite and associated more mafic lavas of the Latir volcanic field are preserved as far as 45 km beyond the source caldera. Within the caldera, the tuff ponded to a thickness of 2-3 km and enclosed chaotic megabreccia fragments which slumped from the caldera walls. At the time of ash-flow eruption, the volcanic field was severely deformed along northwest-trending faults related to the Miocene Rio Grande rift, with most intense deformation occurring within the caldera. Strata were steeply tilted and locally overturned along presumably listric faults. Ash- flow tuffs locally underwent secondary flowage over concurrently developing fault scarps and accumulated within structural basins as rheoignimbritic lava flows. Cogenetic batholithic granitic rocks, exposed over an area of 20 x 35 km, range from mesozonal quartz monzonite to epizonal porphyritic granite and aplite, with the shallower and more silicic phases most abundant within the caldera. Compositionally and texturally distinct granitic phases define a highly evolved resurgent intrusion within the caldera, an incomplete ring dike along its southern margin, and a large mass of less fractionated quartz monzonite south of the caldera. A negative Bouguer gravity anomaly is closely confined to the area of ex- posed granitic rocks; it also reflects boundaries of the Questa caldera. The gravity anomaly is interpreted as defining the extent of the underlying batholith, emplaced into lower parts of the volcanic sequence and underlying Precambrian rocks. Paleomagnetic determinations indicate that the granitic rocks were above Curie temperatures at the time of caldera formation and regional listric faulting, yet most are little different in radiometric age from the intensely deformed volcanic rocks. These relations indicate that the batholithic complex represents the source magma body for the volcanic rocks, into which the Questa caldera collapsed, and was largely liquid at the time of regional tectonic disruption. Compositions of the volcanic and plutonic phases changed from early calc-alkaline metaluminous rocks, to weakly peralkaline silicic rhyolite and equivalent afredsonite-acmite granite at the time of the caldera formation, then back to post- caldera calc-riebeckite granitic rocks. Maximum concentrations of alkalis and minor elements such as Rb, Th, U, Nb, Zr, and Y were reached at the time the caldera formed about 25-26 m.y. ago, but the major molybdenum mineralization of the Questa district took place when the late calc-alkaline granitic ring intrusions were emplaced about 23 m.y. ago, along the south margin of the caldera.

Jan 1, 2013

By Penswick D.

From the perspective of management control, most mining operations can be represented by a hierarchy comprising four layers. The base of this hierarchy consists of the individual pieces of equipment that are used to break and transport rock. The next level comprises the coordinated interaction between different pieces of equipment, termed a process. An operation results from the bringing together of different processes within a common discipline, such as mining or hydrometallurgy. Finally, an enterprise is formed when the separate mining, concentrating and smelting business units are combined. To date, much of the literature written on the topic of mining automation has focused on the equipment level, specifically on removing the operator from production mining equipment. This focus should not, however, overshadow advances registered in automation at both the process and enterprise levels. Only at the operations level of the hierarchy has little progress been made. While automated equipment, process management and enterprise resource planning are a current reality; it is argued that the benefits from automation have, to date, been largely elusive. It is further argued that full benefits of automating other levels will only be fully achieved when this ‘gap’ in the mining automation hierarchy has been addressed and an uninterrupted, process-wide information flow across the entire operation is achieved. Furthermore, it will be reasoned that so-called vertical integration can only be achieved with an automated operational level in place. It is believed that all the necessary building blocks are in place and that the industry is ready for this development. The paper concludes by presenting a vision for what operational level automation would achieve.

Sep 1, 2001

By Nathan Rouse

This blast mitigation study examined the effects of a barrier wall on explosively driven pressures. This area of blast mitigation is of interest due to the many different applications involved in protecting a target from an explosive attack.

Jan 1, 2012

By T. Suganuma

Mitsubishi-Cominco Smelting Co. is a joint venture of Mitsubishi Metal Mining Co. Ltd. (M.M.M.) of Japan and Cominco Ltd. of Canada. The smelter, which is located alongside M.M.M.'s Naoshima copper smelter, was completed in May, 1966 and has a capacity of 36 000 metric tons per year of refined lead. The concentrate feed for the smelter from Pine Point Mines Ltd. is high grade with low impurities; particularly silver, bismuth, antimony, and arsenic, which facilitated a simple plant layout and operation. Concentrate, fluxes, recycle granulated slag and return sinter are drawn from bins by automatic control over weigh belt feeders, sintering is carried out on a 20 m2 Lurgi updraught sintering machine, furnacing in a 3.0 m x 1 ½ m water jacketed blast furnace equipped with an Asarco continuous tapper, refining in four 120 metric ton kettles and casting on a 25 metric ton/hour automatic casting machine. The S@ gas from sintering is cleaned in a high temperature baghouse utilizing glass bags and is then delivered to the M.M.M. copper smelter acid plants. The furnace gases after cleaning in a low temperature baghouse are vented to atmosphere.

Jan 1, 1970

By Claus Becker

The Mixshield is a tunnelling machine for water bearing soft soils. Developed on the basis of the Hydroshield, it extents the application of this machine to cohesive soils. The design of the drum-type machine allows three different applications 1. As shield with liquid supported face and hydraulical mucking 2. As Compressed-Air-Shield 3. As Earth pressure balanced shield. The Mixshield is employed on three big contracts 1. a 6.3 km ring tunnel in Hamburg, outer diameter 5.95 m, with a new developed segmented concrete lining 2. a 1.9 km pipe-jack job near Cologne, o.d. 3.6 m 3. Metro Lot 3 in Lille/France, o.d. 7.7 m, 3.2 km long with segmented concrete lining and a most sophisticated separation-plant The site experiences will be reported.

Jan 1, 1987

By L. E. Snow, L. F. Pett

AT the Utah Copper Pit of Kennecott Copper Corp. a versatile mobile drill unit has been developed and tested. Through increased drilling speed and additional available drilling time, an improvement of 233 pct in drill performance has been realized. Operators using drill power can quickly and easily convert the unit from a vertical to a toe hole drill. Drilling is done with the machine in line with the unit or at right angles to it. Table I covers the 1950 drill record at the mine, showing the types of machines used and the footage obtained. [ ] Development of the new units was prompted by a desire for solution of the following problems: 1-The ever-expanding operations within the Utah Pit, requiring some 65 miles of transmission pipe lines radiating from a central compressed air plant, have now taxed this compressor plant beyond capacity. While 100 lb per sq in. pressure is maintained at compressors, transmission losses from innumerable small leaks result in low terminal pressure at the drills. Fig. 1 illustrates that while terminal pressure varies according to size of air hose and fittings used, the average drill is operating on air pressures within the 60 to 70-lb range. The compressor plant is operated primarily for air rock drills. All drilling is done on day shift, but it is necessary to run two of the three 3720 cu ft capacity compressors during night shift in order to prevent drastic loss of pressure through leaks. On day shift all three compressor units are operated at capacity, so that there is no reserve safeguard available for extensive repairs to any compressor. The calculated volume of compressed air required for operation of 25 drills is but 33 pet of three day-shift compressors. While compressed air is being used to a minor extent for purposes other than drilling, it is felt that satisfactory substitute facilities could be provided in the event that air lines were no longer available. 2-Drill performance has increased beyond the capacity of present 3 ½ -in. drifter machines. 3-The installation, maintenance, and moving of air lines in routine mining is a growing problem. The 2-in. level lines are placed outside electrification towers and must be moved to new location upon completion of each shovel cut. In addition to these moves it is often necessary to dismantle level lines so that excessive shovel spillage, or material covering track following a blast, can be pushed in the clear with bulldozers. Where level room is limited, it is often necessary to remove air lines in giving bulldozers room to prepare grades for wagon drills. In spite of precautions taken, many level lines become buried, twisted, and constricted, with excessive air loss resulting. Excessive back break in blasting often leaves several sections of air line suspended in mid-air. Occasionally air lines come in contact with defective electric transmission towers, so that holes are burned through pipe. 4-Rail-handling of drilling equipment such as wagon drills from one location to another requires considerable locomotive crane crew time. Any new unit developed should travel under its own power. 5-Present practice requires accessory material including hose, water pressure tanks, water barrels, drill steel, and bits to be transported by means of push cars when drill locations are changed on any level. 6-In order to supply numerous drill locations with material, many stock piles of new drill rods, drill bits, and other essentials must be left at strategic points, usually in the vicinity of powder magazines. This practice makes for poor housekeeping and contributes to the loss of supplies. Planning the Unit It was felt that a mobile drill unit which would rectify the foregoing problems should meet certain demands: 1-It must furnish compressed air to operate a 4-in. rock drill at a pressure of 90 to 100 lb.

Jan 1, 1952

By J. -C. Parisien-La Salle, D. Blais, G. P. Demopoulos

"In this work the dissolution, precipitation and adsorption behaviour of gold in acidic iron sulphate media containing small amounts of chloride ions is investigated via batch laboratory tests and OLI thermodynamic calculations over the temperature range 25-250°C. Chloride ions may be present in industrial pressure oxidation/pressure leaching (POX/PL) operations due to elevated water salinity levels or due to intentional addition as is the case of the CESL Copper Pressure Leaching Process. Thermodynamic calculations show that AuCl4 - may form depending on the free Cl-/Au ratio and temperature, its stability increasing with increasing Cl- concentration and decreasing with increasing temperature. On the other hand during POX/PL, we know that massive precipitation of iron in various hydrolysis products and compounds occurs. Hence of interest is the question how AuCl4 - that may form during leaching interacts with the iron precipitation products. Gold(III) chloride was found to co-precipitate with iron(III) (oxy) hydroxides and arsenates forming in the autoclave but not with natrojarosite. Upon further investigation it was discovered that activated carbon added in the autoclave (as done in CIL) acts as preferential sink for the mobilized gold, hence opening the potential for the development of a direct cyanide-free gold recovery process in acidic sulphate leach reactors.INTRODUCTIONThe recovery of gold from ores and concentrates has evolved over the years with processing routes becoming increasingly complex. Given the high value of gold, any reduction in losses during recovery operations constitutes an important economic benefit. One such loss that needs to be addressed is the potential solubilisation of gold during pressure oxidation (POX) of refractory sulphidic gold feedstocks. For example, Agnico Eagle Mines reported a loss in gold recovery due to the formation of a gold chloride complex (Garofalo, 2009). Gold is known to form complexes in solution, such as gold(III) chloride, if an excess of chloride ions are present. The fate of such soluble gold chloride during pressure oxidation and the subsequent neutralization of the acidic discharge slurry will determine if gold is lost or recovered in the downstream cyanidation operation. Thus it is of interest to know under what conditions gold chloride may stay soluble or co-precipitate along primary (formed in the autoclave) or secondary (formed during neutralization) precipitates. Furthermore, the mode of co-precipitated gold, such as adsorption on iron compounds, like goethite and hematite (Machesky et al., 1990; Nachayev, 1984); substitution in one of the precipitated phases; or finally chemical reduction to metallic state would have consequences in terms of gold recovery."

Jan 1, 2012

By John A. Church

IT is a well-known fact that under similar conditions a ton of pig iron can be made from any ore with less fuel when charcoal is used than when coke or anthracite is employed for heating. The cause of this superiority is entirely undiscovered, and no explanation has yet been offered which has won even temporary acceptance. Such as they are the hypotheses heretofore presented are of two general kinds, and they come from those two divisions of the working force which are so often antagonistic in all professions, the scientific and the practical men. The theory of the scientific men is drawn from the chemical reactions which are known to go on in the furnace, and it is well expressed in a recent paper by Prof. Akerman, of the Stockholm (Sweden) School of Mines. It makes the superiority of charcoal as a fuel in the blast furnace to depend upon its quick and thorough reduction of carbonic acid. This property belongs to charcoal in virtue of its porous structure. Its cells have a diameter of only one twenty-four hundredth of an inch, and one grain of charcoal has been computed to have a surface of two and four-tenths square feet. According to the theory in question, carbonic acid is formed by the first impact of the air upon the fuel; but in charcoal furnaces the acid is immediately reduced to oxide by taking the necessary amount of carbon into combination, and the gas reaches its highest reducing power even in the near vicinity of the tuyeres. Coke, being harder, does not produce so strong a reducing gas in that part of. the furnace. Carbonic acid is formed as in the case of charcoal, and remains longer before its reduction to oxide is completed. Anthracite is the

Jan 1, 1879

By R. C. Urquhart, W. P. Channon, D. D. Howat

The mode of current transfer between electrode and slag in the submerged-arc furnace . by W. P. CHANNON, B.Sc.(Eng.)(Student Member), R. C. URQUHART, M.Sc.(Eng.), ;'h.D.(Visitor), and D. D. HOWAT, B.Sc., Ph.D.(Fellow) An account is given of a laboratory experiment in which the resistivity of a primary slag like those produced in the manufacture of high-carbon ferrochromium was measured at current densities typical of operation in a submergedarc furnace. It was shown that the current flow from graphite elec trode to molten slag obeys Ohm's Law when electrode current densities are less than 12 A/cm". At higher current densities, arcing occurs from the electrode tip to the slag, causing an imbalance in the rate of heating in the furnace burden.

Jan 8, 1974

By J. J. Bodmer

THE four different modes, more or less practiced for subdividing slag (that is, producing slag sand), are the following : 1. Crushing the slag from the lump in Blake's crusher, by edge runners or other suitable means. 2. Blowing water, steam, cold or hot air, into the stream of viscous slag whilst it runs from the furnace. So treated, the slag takes

Jan 1, 1874

By F. Z. Utyashev

The present work considers the essence of fragmentation: on the level of a simple model as a material response to the curvature accumulated by it at large deformations. It is on this basis that the correlation between curvature and fragment sizes is determined. It is shown that at deformation the area of curvature center inevitably changes. It is revealed that a specific value of variation of center surface area, i.e. ^As parameter, is numerically equal to the value of curvature acquired by a material. Minimum sizes of fragments and grains depending on ^As have been estimated, and the dependence of this parameter on strain has been established. Besides, the present paper considers the effects exerted by curvature center geometry, material distortion, directions of deformation and thermal warming up in the localization zones on structure refinement when various techniques are applied.

Jan 1, 2006

By Vladimir J. Ovdenko, Sergey N. Lazarenko, Evgeny L. Schastlivtsev

The term sustainable development shortly appeared in international use in the run of UNO Environmental Protection Conference held in Rio de Janeim in 1992, bears the concept, that evolution process ( associated either with a region or society) should provide mutual interests concern in three aspects - environmental, economic and social ones, admitting as well the fact , that environmental protection should become an integral part of each process and cannot be regarded separately. In this connection it seems quite reasonable to employ the principal of sustainable development, while creating the model of industrial mastering the territory constraint lands viewing their future, for a example, in rich mineral deposit's development. In Kuznetsk coal basin in Russia ( west Siberia) the development of a big coal deposit Erunakovsky is now being underway. The major part of coal will be mined with open cast method, resulting the number of local environmental adverse impacts' occurrence. In such a situation mastering of sustainable development model is given the top priority, demonstrating the essential result of its application in a form of possibility to define the best correlation between economically expedient and environmentally tolerable loads during coal mining. The given paper is an attempt to work out the main principals to approach the creation of sustainable development model in regard of the definite region case. To simplify the presentation of employed approach's main idea, the given below accepts as its component only one of many actually existing environmental profiles, that define mining pro- cess impact on environmental situation -the size of infringed (de- graded) lithosphere surface. Basically, the actually existed correlation between spheres. grounding the model of sustainable development - economic, environmental and social- is given in a form of nomogram under Fig.1. On the presented graph the prognostic values of broken lands relative extent within Erunakovsky boundary ( to be compared with total region area taken as 100%) are arranged on axis x". Axis "y- demonstrates the main values associated with complete economic background, making the intrinsic part of the principal for sustainable development, i.e. annual coal output for the given area. It's top, used in assessment value relates to actual showings implied for the study region project and quantifies 60 min. tons. While regarding the social facet of principal for sustainable development, the applied mode to separate social issues into two types - one profiling a welfare standard of living and the other. pertaining the way environmental situation contributes to the degree of &ologica-1 comfort in people's living was defined as the most expedient and the most adequate in the matter of reflecting the actual terms of vital activity of the society. In accordance with the cited above the economic level showings are plotted on the graph on "-x” axis, while "-y" one obtains the values associated with the point of ecological comfort presented in conventional units. For the maximum possible conventional point of living (corresponding in nomogram to 1.0 value) a welfare level secured with industrial region economic activity revenue was assumed in case the top planned annual amount of coal is delivered ( 60 min. tons). While studying the index of public economic welfare, environmental conditions corresponding level in its original state i.e. prior to any industrial work carried in the region, was adopted as its top possible conventional rating (1.0). The given nomogram displays the integrity of x-f(y) type interrelations plotted on the basis of four separate dependencies, precisely a) the size (area) of infringed earth's surface as a function of coal output in the region; b) subordination of ecological comfort of people's living to the degree of lands infringement; c) interconnection of economic and environmental components of people living; d) interconnection of economic level of people's living and the amount of coal mined in the region. Linked to a single unit, these separate plain dependencies create, as seen from the graph, a more intricate system of bonds, that affords during defining or changing this or that system parameter to secure undergoing changes, that occur to other parameters of the system. The mentioned reason made it possible to consider and drive to mutual conformity ( as far as it is possible) all parameters values for the defined system's relations, that in their turn indicate the concern of other aspects of a sustainable development principal. According to the graph, in order to get not more than 50% of infringed land left after the deposit's mining, it is advisable to ex- tract not more than 40 min. tons of coal annually, gaining in this case the level of ecological comfort for living in the amount of not

Jan 1, 1996

By Volkan Arslan

This study aimed to remove the contaminants in quartz sand by using an eco-friendly method and to obtain high-purity quartz. For this purpose, ultrasound-assisted acid leaching was applied. Equal amounts of a mixture of diluted hydrochloric and oxalic acids were used as the solvent. Response surface methodology (RSM) was used for optimizing, modeling, and predicting the experimental parameters. The correlation coefficient ( R2) of the proposed quadratic model for the relationship between iron removal yield and test parameters was calculated as 0.9731 and it was determined that the predicted and actual values were compatible. Finally, optimization experiments were made and optimum experiment conditions were revised and determined as 83.38 °C of leaching temperature, 196.35 min of leaching time, 2.86 M of acid concentration, and 202.24 W of ultrasound power. Under the optimum conditions determined after optimization, the highest yield of iron removal was determined as 95.08%. Under the optimal parameters, the SiO2 content of the concentrates increased from 97.841 to 99.907% and the Fe2O3 content reduced from 0.225 to 0.011%.

Jul 12, 2021