Search Documents

By John Blackshaw

NEW sources of supply of tungsten concentrates became necessary when the flow from the Far East was blocked in 1942. In Canada, one source has been noted in the workings of the Hollinger mine at Timmins, Ontario. For many years, a small amount of scheelite had been removed with the gold ore, and an appreciable tonnage of scheelite still remained in the mine. At the request of the Dominion Government, a plant was built to recover this scheelite in the form of a concentrate that could be used by the alloy-steel industry without further preparation. The plant began operating early in March, 1942, and a small tonnage of ore, carrying scheelite and gold values, has been treated daily since then. The possibility of recovering the scheelite had been considered on several previous occasions. Each time the proposal had been given up because the total profits from the enterprise were estimated to be insufficient to repay the capital cost of building the recovery plant. At the time the plant was built, additional information had been gathered about the tonnage and grade of the scheelite ore in the mine, and several thousand tons of ore grading higher than 0. 25 per cent WO3 (tungstic trioxide) were known to be available.

Jan 1, 1943

By Zuoren Huang

The flowsheet of the hyd.rametallurgical zinc plant which is in use at Zhuzhou Smelters is described. The principal features of the process are fluid bed roasting, continuous calcine leaching, solution purification, zinc electrolysis, electrolyte cooling, and finally, the melting and casting of zinc forms. The Zhuzhou process for the flotation of silver from the leach residue collected on the Moor filters is described. The technical details of the process are outlined and the operating data are analyzed. The flotation facilities are described in detail and concentrate grades and recoveries are presented. The waelz process is used to concentrate In, Ge and Ga remaining in the leach residue after silver flotation. These elements subsequently are recovered by selective leaching in sulphuric acid, and details of this operation also are presented.

Jan 1, 1990

By R. W. Ruddle

The advent of new methods of roasting, “flash roasting and fluidisation”, which are now under development, combined with the use of oxygen-enriched air, may markedly increase the SO2 content of roaster smokes. Skogmo suggests that the production of smokes containing as much as 50 per cent SO2 should be feasible. The use of flash smelting processes may well enable a similar increase in the SO2 content of smelter smokes to be made. In this event the recovery of sulphur would be greatly cheapened and the process might well be much more economic, even if allowance is made for the cost of generating the oxygen

Jan 1, 1953

By Zhao-feng Xie

A new process of recycling valuable metals containing in the slag of jamesonite smelting in the blast furnace was studied. In this process, the valuable metals such as Pb, Sb, Zn and In etc. were fumed and volatilized and enriched in the dust firstly and then the dust was leached by sulfuric acid. In the leaching procedure, Zn and In in the dust entered into the leaching solution and were separated from Pb and Sb which remained in the residue.The optimal operation conditions of the fuming procedure are as follows: the mass ratio of the blast furnace slag, coal powder and lime are 100:22:10 respectively and the fuming time are 1.5~2.5 h, the fuming temperature is not below 1200C and the volatilization rates of Pb, Sb, Zn and In are 95%, 92%, 86% and 75% respectively. The optimal conditions for the leaching procedure are also presented: the consumption of sulfuric acid is 1.15 times of the theoretical consumption, the ratio of liquid to solid is 4:1 and the leaching temperature, leaching -1time and stirring speed are 90, 1.5h and 300 r?min separately. The leaching rates of Zn and In are 98.5% and 95.2% respectively. The experimental results shows that the valuable metals in the dust can be recovered and separated effectively by this process and the?ir recovery efficiencies are as follows: Pb94%,Sb91%, Zn84% and In69%.

Jan 1, 2009

By G. E. Murray

Introduction The development of the method for recovering zinc from lead blast-furnace slags at Trail is interesting and important in the history of both lead and zinc metallurgy. Many efforts have been made in the past, particularly in Germany, to make economic recovery of zinc from slag. The Pape process on Oker slags was successful and is being worked at the present time. More recently the Waelz process has come to the fore. One effort at Cockle Creek, Australia is of special interest in view of subsequent developments. This was re-ported in detail by Guy Courtney in 1920(1). It deserves mention as it shows how, as in many other instances in the metallurgy of lead and zinc, important pioneering work has been done in Australia. These experiments, started over 25 years ago, comprised reduction with coke, powdered coal, and eletrothermically in carbon-lined furnaces. The so-called slag eye furnace, which volatilised the metals from a blast furnace running with a hot top, was also investigated.

Jan 1, 1933

By M. Holmes, R. Molnar, E. Norton, K. Baxter, J. Riordan

The Boleo Copper-Cobalt-Zinc-Manganese Project of Baja Mining Corp. is situated adjacent to Santa Rosalia on the Baja Peninsula of Mexico. The El Boleo ore is a mixed oxide-sulfide deposit with major values in copper, cobalt, zinc and manganese. The metallurgical process designed to treat the El Boleo orebody involves a sulfuric acid leach in seawater using oxidative and then reductive leaching to maximize metal extraction. The leach solution is separated from the barren solids via counter current washing through a series of high rate thickeners. Copper is recovered using conventional SX-EW processing as cathode. Zinc and cobalt are extracted from the copper SX raffinate after iron and aluminum precipitation. The CSIRO DSX solvent system (Versatic® 10 and LIX® 63 mixture) are used in this extraction. Manganese remains in the DSX raffinate and is recovered by soda ash addition as a high quality manganese carbonate precipitate. Zinc and cobalt are acid stripped from the loaded DSX solvent. Zinc is then re-extracted away from cobalt using Cyanex® 272 extractant and stripped into a highly concentrated strip liquor (+100 g/L Zn) and directed to either a spray dryer or a granulator for production of zinc sulfate monohydrate. The zinc solvent extraction raffinate, containing cobalt, advances to another SX circuit using Cyanex® 272, for the recovery of cobalt as cobalt cathode. In this paper, the detailed results from bench and integrated pilot plant testing for zinc recovery from the El Boleo ore will be described. The results of this testing are currently being used to engineer the commercial plant at El Boleo.

Jan 1, 2008

As the question of zino recovery from lead blast furnace slags has lately become such an important subject with lead metallurgists, the following description of some of the work carried out in this oonnection by the Sulphide Corporation, at CockleCreek, should prove of interest to those concerned. Early in the life of the works it was realised by the metallurgical staff that a very wide field for investigation lay before them. At the head of these was the late Mr. F. H. Evans, and it was due to his work and suggestions that the question has grown from a mere hypothesis to a commercial undertaking, in so far as these works are concerned. A great deal of the early work was carried out in the form of small laboratory expe!iments, those giving the best results being ear-marked for subsequent trial on a larger scale. One of the main obstacles in the way of research was the lack of any data or information of similar work done in other...

Jan 1, 1920

By Paul R. Kruesi

A patent-applied-for process has been developed in which zinc chloride is extracted by tributyl phosphate in kerosine, and stripped with ethylene glycol or ammoniated ethylene glycol. The anhydrous zinc chloride is precipitated from the glycol as the ammine and zinc chloride is prepared by thermal decomposition with recycle of ammonia. The process permits the production of high grade zinc from scraps and drosses. Its applicability to the recycling of zinc will be illustrated.

Jan 1, 1984

By W. A. Alexander

Introduction In the course of a programme of research on beryllium in progress in these laboratories, knowledge of the recrystallization temperature became necessary. As the information is not available in the literature, the determination of this temperature for metallic beryllium was undertaken. By the reduction of grain size through working and recrystallization and the probable simultaneous induction of preferred orientation, it was hoped to improve the working properties of beryllium at lower temperatures. The recrystallization temperature is usually determined by observing the lowest temperature of annealing at which new crystals are formed in severely cold-worked metal or alloys. This temperature is profoundly influenced by the following factors: the purity of the metal, in the case of an element, or the composition of the alloy; the degree of straining or working; the temperature of straining; the original grain size; and the time held at the annealing temperature. The observed temperature is lowered by higher purity, more severe straining, lower temperature of working, smaller original grain size, and longer time of annealing. Beryllium presents special difficulties in that the percent elongation in tension is effectively zero, so that ordinary squeezing or rolling was not possible. A possible means of straining was suggested by the fact that indentation hardness tests could be made. It was known from earlier work that the metal could be worked at elevated temperatures, so that working at the lowest feasible temperature and quenching might also be a means of producing strain. The purity of the metal is also a point of some uncertainty in the case of beryllium. Losano has prepared 99.96% Be which appears to be the best reported. Distilled metal used in the present work approached this purity. However, by analogy with other metals, residual impurities may have a pronounced effect on the recrystallization. Further purification of beryllium would evidently entail considerable difficulties due to the highly reactive nature of the metal, and was not attempted.

Jan 1, 1947

By Alessandra Bonoli, Garfìm Marianna

"Construction and demolition waste (CDW) is no dangerous material resulting from construction, and demolition of houses, large building structures, roads, bridges, piers, and dams. It is possible to recycle these materials, to reduce environmental impacts, and to reuse them in construction sector. To evaluate in a correct way the possibility to reuse this material it is important to lead laboratory tests to assess the proprieties and quality characteristics. European, Italian and British ad hoc Committees had elaborated specific Standards, to evaluate Geometrical, Physical, and Chemical requirements of recycled materials. A research was carried on to define the guidelines for laboratory tests, their suggested values and quality standards. The Construction and Demolition Waste Construction and demolition waste (CDW) is no dangerous, uncontaminated material resulting from construction, renovation, repair, and demolition of houses, large building structures, roads, bridges, piers, and dams. CDW waste is made up of wood, steel, concrete, gypsum, masonry, railway ties, roofing materials, carpeting, insulation, plaster, metal, and asphalt, and all waste included in CER Code 17. In particular Demolition wastes are defined as materials resulting from the demolition, instead Construction wastes are defined as waste materials resulting during construction process or in pre-manufacturing construction industry. Environmental problems In a lot of cases Construction and Demolition Waste materials were discharged in landfills, these are filling up with CDW and others, and some of them will close in the near future. In addition, illegal dumping of CDW debris can result in future health risks, decreased property values, cleanup costs and enviromental problems. The typical environmental impacts generated by CDW dumps are: 1- Dust problem, which causes air pollution, as will as forming dirty areas. 2- Uncontrolled locations, that will encourage the disposal of other waste types with the usual construction wastes leading to an environmental disaster. 3- The degradation and deterioration of the coastal lands and the natural protectorates. 4- The loss of aesthetic features. 5- Occupation of large areas, causing extra hauling costs. Therefore, it is wise to find other alternatives, like reuse or recycling, other than landfilling CDW debris or illegal dumps, because a proper management and the reduction of CDW amount can save money, conserve resources, and preserve the environment."

Jan 1, 2008

By John C. Taylor

With growing emphasis on energy conservation and increased concern over the presence of heavy metals in the environment, it is fortunate that most metals are readily recycled. In this respect, metals have a significant advantage over plastics and similar materials used as metal substitutes. For many years a secondary industry has processed scrap copper, nickel, lead and zinc to produce refined metal which has, to varying degrees, influenced the price and displaced the production of primary metal. This paper reviews some of the challenges the industry will face and the changes in process technology which will be required as pressure mounts to increase the amount of metal recycled. In the case of most base metals, this will have an impact on primary metal production; as the tonnage of metal recycled increases, the requirement for primary production, or new metal, will depend more and more on the growth in consumption.

Jan 1, 1993

By Dezhou Wei, Cong Han, Shuling Gao, Wengang Liu, Yanbai Shen

The recycling schemes of copper mineral to a copper raw ore produced in China is investigated in this paper, of which is aimed at copper concentrate‘s grade is over 26.00% and recovery is over 90.00%. The primary copper mineral the raw ore is chalcopyrite and the main gangue minerals are quartz, orthoclase, albite, clinochlore and phlogopite. There are four useful metal elements contained in the copper raw ore, which are Cu, Pb, Zn, Au and Ag, and the grade of each is 3.75%, 0.01%, 0.11%, 0.31 and 483.5 g/t. Two floating recycling schemes and its corresponding flotation reagent system were determined. The results show that calcium oxide, sodium carbonate and sodium sulphide were used as regulators, sodium n-butylxanthate was used as collector and terpenic oil was used as frother in two floating recycling schemes are effective. The open-circuit test’s results show that the copper mineral contained in raw ore can be effective collected, and both concentrates gotten through two schemes are up to grade.

Jan 1, 2014

By D. A. Rhys

"The Red Bluff porphyry is a tabular 2 km long north-west trending Early Jurassic quartz diorite to monzodiorite body that intrudes a folded Triassic greywacke sequence in the lskut River area, northwestern British Columbia. The porphyry is 500 m to 800 m northeast of the Snip orebody, which is a southwest-dipping shear-vein, termed the Twin zone that contains approximately 35 tonnes of gold.The intrusion associated with the mineralization is characterized by 0.3 cm to 4 cm phenocrysts of K-feldspar in a mediumgrained plagioclase porphyritic matrix. It is overprinted by pervasive sericite + quartz ± K-feldspar ± biotite (potassic) alteration characterized by intense stockworking of quartz veins containing magnetite--hematite bands. This assemblage is cut successively by quartz veins with minor iron-oxides and pyrite, and by younger pyrite veins with phyllic envelopes. The system is gold-rich but copper-poor, with typical grades between 0.25 g/t and 0.6 g/t Au, and 0.1% and 0.2% Cu. All styles of alteration and veining have similar abundances of these metals. Where southwest- and north-east dipping shear zones are developed in the porphyry, veins of all types are sheeted and foliation parallel. These sheeted zones are interpreted to be syntectonic. Asymmetric phenocrysts, folded veins and oblique foliations developed in the 130 haulageway of the Snip mine imply oblique normally-directed shear on the southwest-dipping foliation.The adjacent Twin zone is a high-grade auriferous shear-vein system that is internally banded with: (1) carbonate-chlorite-biotite veins, with textures indicating formation at least partially by wallrock replacement, and (2) dilatant quartz-sulphide veins. Veins commonly have potassic alteration envelopes that contain biotite ± calcite ± K-feldspar. The zone is highly deformed and schistose, with numerous kinematic indicators including shear bands, asymmetric folds, rotated porphyroclasts and oblique foliations that indicate a normally-directed shear sense which is parallel to that indicated by fabrics within the porphyry.Precious and base metal veins within 2 km or 3 km of the Red Bluff porphyry are zoned. Veins and shear-veins proximal to the intrusion, such as the Twin zone, are typically enriched in gold, copper and molybdenum, and have potassic alteration envelopes dominated by biotite. Distal veins usually contain relatively abundant zinc and lead and have sericitic alteration envelopes. Structures of both types have an Early Jurassic galena Pb-Pb isotope signature.The similarities in structural fabrics and alteration histories in both the Twin zone and the porphyry, the zoning of the vein systems in the area, and the apparently concordant Early Jurassic zircon U-Pb age from the porphyry and galena Pb-Pb dates from the Twin zone and surrounding vein systems suggest that intrusion, semi-brittle deformation and a large mineralizing hydrothermal system were closely related temporally and genetically."

Jan 1, 1995

By George Hope, Brigitte Lacouture

"The Red Dog Mine has increased mill throughput for most years since startup. Although flotation equipment has been added over the last 10 years, the Red Dog metallurgical performance has been restricted by a lack of adequate flotation capacity. Two reduced tonnage trials conducted in 1997 as well as numerous SAG relines have consistently indicated the potential to significantly increase both zinc concentrate recovery and grade with additional flotation capacity. Late in 1999, a new circuit was designed with increased flotation capacity while simplifylng the current circuit, providing for three stages of dilution cleaning, and creating a retreat section. The purpose of the retreat section is to target the more complex particles and allow the chemical environment to be fine tuned for improved iron depression. In total, twentyone (21) Outokumpu OK50 mechanical flotation cells and four (4) 3.66m dia. column cells will be added to the current flotation circuit. The VIP (Value Improvement Program) Mill Optimization project is also addressing thickening, water treatment and power issues and has a total budget of $US105 M. Startup of equipment will be phased in to minimize the impact on current operations and is expected to be complete by the end of Q3-2001.INTRODUCTIONRed Dog Operations started production in November 1989. The mine is located above the arctic circle in northwest Alaska. It is linked by an 80 km road to a port-site facility where the concentrate is stored. Concentrate is shipped to markets throughout the world during the one hundred (100) days of open seas. Typical of sedimentary exhalative deposits, the metallurgy proved to be challenging and coupled with many mechanical shortcomings, the initial few years were very difficult. The start-up issues were slowly resolved and in 1998, a major grinding expansion, the PRI (Production Rate Increase) project, was completed. The project was designed to allow a 40% increase over the 1995 throughput. In 2000 mill throughput was 3,050,000 tonnes to produce a total of 960,000 and 140,000 dry tonnes of zinc and lead concentrates respectively, making Red Dog the largest zinc concentrate producer in the world. To address a shortage of flotation capacity remaining from the PRI grinding expansion, a project designated as the VIP (Value Improvement Program) Mill Optimization project was initiated. The mill optimization project is targeted to produce 1,100,000 tonnes of zinc concentrate at 56% zinc grade and 87% zinc recovery. The project will add twenty-one (21) Outokumpu OK50 (50m3) flotation cells, four (4) 3.66mO column cells and address water treatment, thickening and power generation capacities."

Jan 1, 2002

By Steve W. Ciccone

The Red Dog Mine is both the largest known zinc reserve and the largest zinc producer in the world. The mine started in 1989, and by 1999 had increased production from approximately 300,000 tonnes per year (t/yr) of zinc concentrate to in excess of 900,000 t/yr. The VIP Mill Optimization Project further increased zinc concentrate production to 1.1M t/yr while improving both product quality and zinc recovery. The Mill Optimization project also addressed a number of issues related to risk reduction: power generation capacity, water treatment capacity and concentrate thickening. The project was faced with numerous challenges, the most daunting of which was the schedule. This US$105M project was executed, from conception to completion, inside of two years. Less than nine months elapsed from concept to delivery of materials and equipment to site. The project also faced a 100-day icefree shipping window, the challenges of construction in an Arctic environment, and an extremely tight labour market for qualified craft personnel. These challenges were successfully addressed with several innovative approaches to project execution, including an Alliance contracting arrangement between the owner, engineer and contractor; full integration of the team; construction of modules in Anchorage; and fast-track engineering, procurement and construction. Steve Ciccone, AMEC?s project manager on the Mill Optimization project, works for the Mining & Metals unit of AMEC, a world leader in the provision of engineering and construction services. He obtained his BASc from the University of British Columbia and is currently midway through his MBA program at Simon Fraser University. Steve has 15 years of experience providing engineering and project management services on mining and metals projects, and has been involved in the execution of five capital projects and several studies at Red Dog since 1995. George Hope was responsible for process design and engineering on the Mill Optimization project and has been Manager, Project Development at Teck Cominco since 1995. Prior to this time, he was a project manager and chief metallurgist for Lac Minerals for 14 years and a mill superintendent and metallurgist for Noranda for 5 years. George received his BSc in Mineral Technology from the Royal School of Mines in England.

May 1, 2002

By George H. Hope, Steve Ciccone

"The Red Dog Mine is both the largest known zinc reserve and the largest zinc producer in the world. The mine started in 1989, and by 1999 had increased production from approximately 300,000 tonnes per year (t/yr) of zinc concentrate to in excess of 900,000 t/yr. The VIP Mill Optimization Project further increased zinc concentrate production to 1.1M t/yr while improving both product quality and zinc recovery. The Mill Optimization project also addressed a number of issues related to risk reduction: power generation capacity, water treatment capacity and concentrate thickening. The project was faced with numerous challenges, the most daunting of which was the schedule. This US$105M project was executed, from conception to completion, inside of two years. Less than nine months elapsed from concept to delivery of materials and equipment to site. The project also faced a 100-day ice-free shipping window, the challenges of construction in an Arctic environment, and an extremely tight labour market for qualified craft personnel. These challenges were successfully addressed with several innovative approaches to project execution, including an Alliance contracting arrangement between the owner, engineer and contractor; full integration of the team; construction of modules in Anchorage; and fast-track engineering, procurement and construction.INTRODUCTIONThe Red Dog Mine, which began operations in 1989, is located above the Arctic Circle in Northwest Alaska, approximately 145 km north of Kotzebue (Figure 1). An 80-km road connects the mine site to the DeLong Mountain Transportation System (DMTS) port site. Red Dog is the largest known zinc deposit in the world, with known reserves totalling 94.5M tonnes, and is the largest zinc producer with a concentrate production rate of more than 1.1M t/yr.Open-pit mining is by typical drill, blast and load operation using moderately sized mining equipment. Ore is processed through conventional crushing, grinding, and flotation to produce separate lead and zinc concentrates. Filtered zinc and lead concentrates are trucked year-round to the DMTS port site, where they are stored in two A-frame buildings, 330 and 440 m long. A lightering barge system is used to transfer concentrate from the shallow water load-out to deep-sea vessels anchored approximately two miles offshore. Shipping is limited to a 100-day, ice-free window beginning in early July."

Jan 1, 2003

By George Hope, Brigitte Lacouture

"The Red Dog mine has increased mill throughput most years since start-up. Although flotation equipment has been added over the last 10 years, the Red Dog metallurgical performance has been restricted by a lack of adequate flotation capacity. Two reduced tonnage trials conducted in 1997 as well as numerous SAG relines have consistently indicated the potential to significantly increase both zinc concentrate recovery and grade with additional flotation capacity. Later in 1999, a new circuit was designed with increased flotation capacity while simplifying the current circuit, providing for three stages of dilution cleaning, and creating a retreat section. The purpose of the retreat section is to target the more complex particles and allow the chemical environment to be fine tuned for improved iron depression. In total, 21 Outokumpu OK50 (50 m3) mechanical flotation cells and four 3.66 mØ column cells were added to the current flotation circuit. The VIP (value improvement program) mill optimization project is also addressing thickening, water treatment, and power generation issues and has a total budget of US$105 M. Start-up of equipment was phased in to minimize the impact on current operations and the project was completed by the end of 2001. IntroductionRed Dog Operations started production in November 1989. The mine is located above the Arctic Circle in northwest Alaska. It is linked by an 80 km road to a port-site facility where the concentrate is stored. Concentrate is shipped to markets throughout the world during the one hundred days of open seas. As of January 2002, the Red Dog main pit had 38.4 Mt of reserves grading 19.2% Zn, 5.3% Pb, and 102 g/t Ag. Additional reserves and resources contribute an additional 72 Mt at 15.6% Zn, 4.2% Pb, and 78 g/t Ag. Red Dog is a Mississippian to Permian, black shale-hosted, zinc-lead-silver deposit located in the DeLong Mountains, western Brooks Range, Alaska. All the rocks associated with the mineralizing event are considered to be part of the exhalite rock package. Silicification was a dominant component of the mineralizing event and the host shale has been silicified and locally resembles a chert. The major sulphides in decreasing order of abundance are sphalerite, pyrite, marcasite and galena. Most of the deposit’s silver occurs within the crystal structure of the galena. The dominant ore mineral, sphalerite, is very fine grained to amorphous and is commonly intergrown with silica. Ore textures are massive, fragmental, chaotic, veined and rarely show classic sulphide sedimentary layering. The upper portion of the orebody has been physically and chemically weathered. Oxidation has altered the sulphides to sulphates. The zinc and iron sulphates are very soluble and are readily depleted from the weathered cap, while the lead sulphate is residual and is, therefore, enriched."

Jan 1, 2003

By B. K. Gorain, A. W. Stradling

"The traditional metallurgical scale-up techniques for flotation plants are based on lumped flotation rate constants, dimensionless hydrodynamic numbers and the use of safety factors. Once the plant has been designed, the flotation principles that govern scale-up play almost no role in the optimization of the circuit to meet its metallurgical targets. This deficiency can potentially lead to a plant design incapable of meeting its targets, especially when circuits incorporate large flotation cells. This paper demonstrates the application of the k = PSbRf model in providing a suitable framework for flotation modelling, scale-up and circuit optimization, thus presenting an integrated approach to the problem. Studies were conducted at Teck Cominco’s Red Dog concentrator to characterize cell hydrodynamics, gas dispersion properties, froth flow behaviour, entrainment and ore floatability to obtain the key data necessary to develop a model for the flotation circuit. The findings of these studies are presented in this paper, which provide valuable insights into the modelling and optimization of the Red Dog flotation circuit. IntroductionThe traditional methodology for flotation scale-up and plant design is based on the ruleof- thumb with safety factors and dimensionless hydrodynamic group similitude considerations. With the recent trend toward larger flotation cells with volumes of 150 m3 and greater in concentrators, the problem of scale-up has become even more acute. The scale-up factors that may have been tolerated on smaller cells are not applicable to larger cells. The transportation of froth in these large cells adds further complexity to the problem. Arbiter et al. (1980) foresaw this problem and pointed out that if scale-up were attempted by rule-ofthumb and trial-and-error, the probability of failure would then increase with scale. This problem is confounded by the fact that the design and scale-up considerations used for a new flotation circuit play almost no role in optimization of the circuit to meet its metallurgical target. This results in a plant design, which may be incapable of meeting its metallurgical targets. There have been several instances where new concentrators have required significant circuit modifications and additional capacity to achieve design targets."

Jan 1, 2003

By Eugene F. Casey, John G. Ruggiero

INTRODUCTION Construction of tunnels in urban areas, especially reclaimed areas, pose many problems. The Red Hook Intercepting Sewer Tunnel, Contract 1A is a portion of the Red Hook Water Pollution Control Project located along the Brooklyn waterfront in New York City. This contract required the construction of a 2620 meter long (8600 L.F.), 3 meter (10-foot) diameter soft ground tunnel, eight Tunnel Manholes, nine Regulator structures, four Diversion and Tidegate structures and 765 meters (2500 L.F.) of branch intercepting sewers of diameters between .30 meters (12 inches) and 1.8 meters (72 inches). The construction contract bid price was $62 million with a duration of three years. The tunnel route crosses over five sets of operational twin cast iron subway tubes with clearances ranging from 4.3 meters (14 feet) to as small as 0.35 meters (14 inches). The route of the tunnel traverses historically interesting areas which have been reclaimed over the last 200 years. This paper is a case history describing the contractor's methods utilized to successfully advance the work through the above problem areas. LOCATION The Red Hook Intercepting Sewer Tunnel is located in the Borough of Brooklyn of New York City. The route is

Jan 1, 1981

By J. M. Newell, G. R. Peatfield

"The Red-Chris porphyry Cu-Au deposit is located between Ealue and Kluea lakes, southeast of the village of Iskut on the Stewart Cassiar highway in northwestern British Columbia. It was explored by Texasgulf Inc., in a joint venture with Great Plains Development Company of Canada, Ltd. and Silver Standard Mines Ltd., during the period 1973 to 1980. Exploration resumed in 1994, following acquisition of the interests originally held by Texasgulf and Great Plains Development by American Bullion Minerals Ltd.Prospectors were first drawn to the area by prominent limonitic stain zones exposed in creek gullies in the western part of the property. These zones are developed on the alteration halo at the western periphery of the deposit. The potential ore zones do not crop out and were first exposed in a bulldozer trench excavated in 1971. Subsequent exploration was by percussion and diamond drilling, guided to some extent by induced polarization surveys. In 1976, estimated resources contained within two crudely designed open pits were 41 million tonnes with an average grade of 0.56% Cu and 0.34 g/t Au, with a cutoff grade of0.25% Cu. New resource estimates based on a major drilling program completed by American Bullion in 1994 were released as this paper goes to press. These estimates were calculated using various copper cutoff grades; at the 0.4% Cu cutoff, the ""in-situ geological reserve"" is given as 100 million tonnes grading 0.58% Cu and 0.46 g! t Au (American Bullion Minerals Ltd., 1995).The deposit consists mainly of pyrite, chalcopyrite and increasing bornite at depth, in zones of quartz-vein stockwork hosted by an elongate body of altered monzonite porphyry of latest Triassic or earliest Jurassic age. The stock intruded volcanic and sedimentary rocks of probable Stuhini Group affinity and is in faulted contact with sedimentary rocks of the Jurassic Bowser Lake Group. Gypsum stockworks are developed in the higher levels of the subvolcanic porphyry system. Late-stage quartz-carbonate veins carry small amounts of galena and sphalerite. Complex faulting within the deposit makes drill-hole correlations difficult. Alteration assemblages include an early potassic phase, almost completely destroyed by later phyllic alteration, and surrounded by a propylitic assemblage dominated by ankeritic carbonates in altered sedimentary rocks.The deposit has characteristics of bath the alkalic and calc-alkalic classes of porphyry copper deposits. The development of quartzvein stockwork suggests a calc-alkalic affinity, but the hostrocks contain little or no free quartz, molybdenum is present in trace amounts only and gold values are significant. Copper grades vary between wide extremes with unusually high grades in some sections of the deposit. The weight of evidence available in the 1970s led us to place the Red-Chris deposit firmly in the alkalic family. The quartz-sericite alteration assemblage was attributed to breakdown of potassium feldspar in a near-surface alteration environment in which seawater may have had a significant role. These interpretalions are retained here, but preliminary conclusions from the most recent work suggest that they may require some modification."

Jan 1, 1995