Search Documents

By R. H. Clarke

"INTRODUCTION Characterization of waste rock is frequently an oversight in mine planning which can contribute to significant delay in permitting and ultimately development. Thorough waste rock characterization is now a prerequisite to developing operating and closure plans acceptable to regulators and the public. BACKGROUND A long history of mine development has placed virtually all focus on the economic extraction and beneficiation of ore materials, while waste rock characterization and management received substantially less attention and consideration. Inadequate waste rock characterization has contributed to planning and management practices that are having unintended and unforeseen impacts to surface and groundwater, and in some cases lead to significant long term closure liability. In response, the regulatory community has developed guidelines for performing waste rock characterization during the pre- mine permitting process that in some cases seem onerous (BLM, 2013). Additionally, where a project proponent has not met these guidelines or results have been deemed “inadequate”, the Nevada Division of Environmental Protection and Bureau of Land Management (regulatory agencies) will only issue operating permits with rigid management practices to address the uncertainty, including requirements for lining waste rock facilities. WASTE ROCK CHARACTERIZATION FOR NEVADA PROJECTS Newmont Mining Corporation (Newmont) operations in Nevada approaches waste rock characterization like ore characterization, as it requires a similar investment of time, funding and attention to detail in order to pass public and regulatory scrutiny. Newmont follows a tiered approach to characterization that creates three over-lapping data sets representing an “escalation” in analysis at each tier, an approach that has thus far gained regulatory approval. “Tier 1” waste rock characterization for most Newmont projects begins with exploration drilling which follows internal standards and procedures. 20-foot composite samples are prepared from all drilling and analyzed for multiple trace elements using inductively coupled plasma mass spectrometry (ICP-MS) methods and for acid-base characterization using method ASTM-E1915. If the exploration program is successful and further resource or reserve development is recommended, the Tier 1 data are used to prepare a Waste Rock Characterization Plan (Plan) that will be presented to regulatory agencies as a part of baseline project characterization."

Jan 1, 2015

By Mark R. Stanton

Geochemical and mineralogical analyses of 46 samples from six drill cores in the Mayday mine pile near Silverton, Colorado, demonstrate wide variability in trace metal contents with spatial location. This variability results from the original geochemical composition of mined rocks, mixing of ore and non- ore rocks during emplacement of the pile, and weathering since rocks were placed in the pile. Weathering reactions are controlled by factors such as pile thickness (depth), water availability, microbial activity, and mineral dissolution and formation kinetics. These factors result in variable redistributions of trace metals from primary (ore) to secondary (weathering products) minerals within each core.

Jan 1, 2000

By Donald V. Fites

The evolution of open-pit mining has been rapid during the last two decades. The development of larger, more productive and efficient equipment has been one of the key factors in this open-pit advancement. Selection of the proper equipment and its correct usage is paramount to successful operation while maximizing return on investment. The quantity of material being moved prior to mining the saleable product is increasing at a significant rate. For example, at a southwestern copper mine more than two hundred million tons of over- burden have been removed prior to exposing an ore which contains less than 1% copper. A recent survey of twenty-three Western Hemisphere copper mines reveals the average strippingratio was 2.2:l with a range of 0.9-8.5:l. In the face of increased mineral demand, the resulting technological developments and rising overburden to ore ratios, many open-pit mines now use totally different concepts for the removal of ore and overburden. An increasing number of these concepts now being installed include wheel tractor scrapers as a major part of the material handling system for unconsolidated overburden removal. To say scrapers move only unconsolidated overburden is incorrect. On the contrary, ripped phosphate rock, copper ore, iron ore, and moderately consolidated overburden are also being moved by scrapers in various areas of the world. As reported in the Minerals Year- book, however, about one-half of the material moved in metal and non-metal mines is never drilled and blasted or broken by other means. We will, therefore, in this paper, concentrate on the role of wheel tractor scrapers in unconsolidated overburden; the area of greatest usage.

Jan 1, 1969

By Dee Bradshaw

"Process mineralogy’ is a form of applied mineralogy which focuses on addressing problems associated with the processing of ores. ‘Mineralogy’ is the scientific study of minerals and ‘mineral processing’ is the production of concentrates from ores. ‘Process mineralogy,’ however can be defined as the practical study of minerals associated with the processing of ores, concentrates and smelter products for the development and optimisation of metallurgical flowsheets, including the waste and environmental management considerations. This hybrid discipline consists of teams that include geologists, mineralogists, samplers, mineral processors and often others, working together. The degree of cross-training, communication and trust dictates the potential capacity of the team and where an appropriate work dynamic is fostered, in which relationships flourish as much as does the ethic of technical excellence, it is possible to develop technical capabilities that surpass those of conventional teams. The world’s demand for metals is ever increasing and ore deposits available for extraction and processing are lower grade and more complex, often containing deleterious elements that require tailored treatment. Generally, in the past, the technical challenges only needed to be overcome and assessed economically to make an ore deposit viable; increasingly and in the future, a more sustainable approach including environmental and societal considerations is needed. Process mineralogical assessment is increasingly providing the critical information that stands between failure or collapse and survival or success of some mining operations. In this paper, selected case studies are used to demonstrate the valuable role of the process mineralogy tools being used to provide the platform for innovative technology development. Their common attributes are discussed and distilled, thus providing some insights and potential guidance for addressing some of the likely future challenges of the mining industry."

Jan 1, 2014

By Bernard P, Lhoumaud E, Gunzburger Y, Conin M, De Santis F, Kinscher J

Seismic repeaters are commonly observed in natural fault zones dominated by slow aseismic motion. The corresponding seismic signal, characterized by highly similar wave forms, is usually interpreted as the repeating ruptures of locked asperities on fault planes (“patches of higher roughness”), loaded by a-seismically slipping areas (“creeping areas”) (Chen & Lapusta 2009; Bourouis & Bernard 2007). Only very few occurrences of seismic repeaters have been reported in underground mines, where these phenomena are rather unexpected since the stress state and the seismic wave propagation continuously evolve with the advancing excavation front (Kinscher et al., 2020). A recent study based on a local seismic network installed in the underground mine of Garpenberg, Sweden, has shown that seismic repeaters and multiplets represent the main part of the total released seismic energy (magnitude of seismic events: -2 < M <1, on moment magnitude scale), with some seismic families being active during several months to years. It is suggested that repeaters are linked to aseismic slip on pre-existing talc-filled fractures, induced by the excavation, and loading of asperities. These results imply that part of redistribution of stresses in the mine is due to aseismic slip, which might explain the observed distant and delayed seismicity.

Apr 26, 2022

By Nagahiro Saito, Takahiro Ishizaki, Mituhito Hirota, Akio Fuwa

"Owing to their extremely high toxicity in the environment, the dioxins have been attracting social, technical and scientific attention in recent years. The authors theoretically had predicted the thermodynamic properties of all the dioxins via quantum chemistry and statistical thermodynamics and elucidated the generation-decomposition behavior of dioxins in the equilibrium calculation· of C-H-0-Cl system. In actual combustion processes, it is said that metallic compounds have much influences on the dioxins behavior. The aim of this study is to reveal the roles of metallic compounds the generation-decomposition behavior of dioxins is revealed from the viewpoints of quantum chemistry. Especially, the catalytic effect of copper has been investigated for the reaction, 2HCl(g)--H2(g}+Cl2(g) and for the etherification reaction from precursors, which is Phenol(g) here, to dioxins. The catalytic role of Cu is shown to have much influence on the generation -decomposition of dioxins.1. IntroductionIt is well known that dioxins are very harmful not only for our health but also for that of our children and grandchildren because they are very stable substance and their reaction rates of decomposition are considerably low. On the other hands, it is not well know how dioxins are generated and decomposed; the generation-decomposition conditions and paths as well as the catalysts to decompose them'1l. The authors believe that the thermodynamic and kinetic study of dioxins is useful to find a solution to these issuers. The authors have been investigating the following problems to reveal the generation-decomposition behavior of dioxins; (a) the prediction of the thermodynamic parameters of dioxins (2), (3), (b) the generation -decomposition behavior of non-chlorinated dioxins by the thermodynamic equilibrium calculations in C-H-O system(4) and (c) the generation-decomposition behavior of dioxins by the thermodynamic equilibrium calculations in C-H-O-CI system(5). Summaries of these thermodynamic researches are as follows.(I) The thermodynamic parameters for dioxins, which had been unknown and/or inaccurate'6 l, could be predicted and are available within the scientific accuracy."

Jan 1, 2000

By E. A. Martell, K. S. Sweder

INTRODUCTION Lung cancer in uranium miners has been attributed to alpha irradiation of basal cells of the bronchial epithelium by radon daughters, primarily by 7.7 MeV alphas from polonium-214 (Altshuler et al., 1964). It also has been was observed that for a given cumulative radon progeny exposure, uranium miners who smoke cigarettes have an incidence of lung cancer about 10 times higher than nonsmoking miners (Lundin et al., 1969). It has been pointed out that the large excess of lung cancer deaths among smoking uranium miners is a multiplicative effect (Doll, 1971), which suggested possible synergistic interactions between airborne radon progeny and cigarette smoking. Experimental studies of the complex pattern of interactions between radon progeny, cigarette smoke particles, and the cigarette smoking process are in progress in our laboratory. Preliminary results, reported elsewhere (Martell, 1981), implicate alpha radiation from indoor radon progeny in the etiology of lung cancer in all cigarette smokers. Cigarette smoking produces high concentrations of smoke particles of low mobility and respirable size--particles between 0.5 and 4.0 µm in aerodynamic diameter (see below). The attached fraction of indoor radon progeny is highly dependent on the air concentration of small particles from cigarette smoking and from other combustion sources (Martell, 1981). The size distribution and other properties of radon progeny associated with cigarette smoke particles enhances their effectiveness in the induction of bronchial cancer in man. In this paper we discuss the properties of radon progeny associated with cigarette smoke, the fractionation of radon progeny and modification of their aerosol properties in burning cigarettes, the role of 218Po in these processes, the production of insoluble 214Pb and 212 Pb enriched particles in burning cigarettes, and the consequent differences in the patterns of polonium isotope alpha irradiation in the bronchial epithelium of smokers. EXPERIMENTAL PROCEDURES Experimental methods used in these studies involve the use of small experimental chambers of known radon and radon progeny concentrations in combination with aerosol collection and sizing techniques and sensitive radioactivity detection methods. The use of low-level [ß-] counting for radon progeny determination, providing a measure of 214 Pb plus 214Bi activity, makes it possible to carry out chamber experiments with small radon emanation sources and relatively low air concentrations of radon and radon progeny concentrations in the range from 100 to 1,000 pCi per liter. Thus, for example, in a typical experiment we use a 10 nanocurie 226Ra solution standard in a 10 liter chamber, providing an equilibrium concentration of 1,000 pCi of radon per liter. In small sealed chambers, radon progeny plate out rapidly on the chamber walls, with steady-state concentrations of airborne progeny less than 2 percent of equilibrium levels. This is experimentally convenient because, upon introduction of high concentrations of cigarette smoke particles or small particles from other sources, there is a systematic ingrowth of attached radon progeny, providing a tagged aerosol source of known age and radon progeny composition. In some chamber experiments a 226Ra solution standard of small volume, acidified to O.1N HNO3, was used as the radon emanation source. When used with a bubbler the holdup of radon in an 8 ml volume of 226Ra solution standard at 0.1N HN03 was only 2% of the total radon in the chamber at equilibrium. For experiments with 212Pb-tagged aerosols, we used a dry Ba(228Th) stearate emanation source prepared by the method of Hursh and Lovaas (1967). 226Ra and 222Rn determinations were made by radon gas counting. The 222Rn in a sealed air or water sample is transferred, using helium gas as a carrier, successively through a dry ice cooled trap at -80°C to remove water, through ascarite to remove C02, and through a small activated charcoal trap at -80°C to collect the 222Rn. Subsequently, by heating the charcoal to 400°C, the 222Rn is transferred next to an LN2-cooled capillary trap, and finally into an alphascintillation counting cell of the type described by Lucas (1957). As already stated, radon progeny activities were determined by low-level [ß-] counting, which provides a measure of 214Pb plus 214Bi. The radon progeny samples, collected on efficient Delbag polystyrene micro-fiber filters or on impactor foils, are placed in close, sandwich geometry between two thin-walled flow counters inside shielding anticoincidence counters and a 15 cm thickness of steel shielding. This configuration provides nearly 4II geometry and a low background of only 0.25 to 0.30 cpm. Aluminum absorber was added to provide a combined thickness of absorber and counter wall exceeding 7.0 mg/cm2 to eliminate the variable contribution of 7.7 MeV alphas from 214Po. 212 Pb determinations also were carried out by low-level [ß-] counting, in this case using a combined absorber and counter wall thickness of 9.0 mg/cm2 to eliminate contribution of 8.8 MeV alphas of 21 Po. In each experiment the [ß- ]activity data were corrected for decay to an appropriate common reference time for assessment of activity distributions.

Jan 1, 1981

By Herbert K. Kutter

This paper is concerned with the physical phenomena in the fracture process of presplitting and only indirectly with the establishment of the optimum presplitting parameters. Its nature is therefore qualitative, rather than quantitative.

Jan 1, 1968

By M. Tangstad

Keywords: Pyrometallurgy, ROMA, Norway, furnace, fines The ROMA project is a competence project on optimizing the usage of raw materials and energy in the ferromanganese, silicon, and aluminium industries. One of the items investigated in this project is the effect of fines on the furnace, and the usage of agglomerates versus lumpy ore. From lab-scale experiments it is shown, that for the charge to agglomerate in the furnace, the charge has to be exposed to a temperature higher than about 1200°C, independent of fines content. The fines less than 1 mm also showed higher agglomeration properties, compared to 2?4 mm, which showed no agglomeration property at all. The properties of agglomerates are very dependent on the pre-treatment of the agglomerate. Sinter and pellets, which have been heated to high temperatures, show a better strength, but also a lower CO reactivity. Sinter also shows a lower melting temperature compared to the ore.

Jan 1, 2011

By Yemi Akinkugbe

Underground coal mining under massive sandstone can present significant challenges if the roof behavior is not well understood. This paper presents a classic cantilever bending/flexing behavior of a longwall tailgate roof caused by the weighting of structurally massive sandstone strata. Nineteen crosscuts of a longwall tailgate under massive sandstone were instrumented with position transducers connected to a data-logger to monitor roof convergence as the longwall face approached. During the monitoring program, an unusual tailgate roof divergence (uplift) was recorded. This roof behavior contradicts expected norm of roof convergence when the longwall is influenced by periodic weighting. The recorded roof movement data indicated that the roof divergence started well ahead of the longwall face. The most inby position transducer started recording progressive roof divergence when the longwall face was approximately 643 feet away. Very gradual roof convergence did not begin until the longwall face got to within 300 feet of the transducer. Recording of accelerated convergence only started after a massive caving event with the face within 280 feet of the recording transducer.

Jan 1, 2007

By V. L. Eardley-Wilmot

Introduction We are all familiar with the bright and attractive colours of the roofs of our suburban houses and country cottages, but few of us fully appreciate the complex and highly technical nature of the business which produces these roofings. Roofing granules consist of small broken particles of certain types of rocks, burned clay products, or slag. They are used either in their natural state or artificially coloured and are affixed onto one surface of asphalt sheeting. Their main functions are to protect the roof against external fire hazard, prolong its life, and enable it to withstand extremes of weather over a period of years without deteriorating. Pleasing designs and colours are added attractions. The reverse, or inner side, of the sheeting is coated with a film of talc or fine mica to prevent it sticking when rolled up for convenience of handling for transport. The finished sheets or strips are cut into a variety of shapes for roofing shingles, or for sidings which resemble rows of bricks separated by mortar. In Canada, the consumption of roofing granules has increased fourfold in the past decade and indications are that the industry will continue to expand. At present, fourteen plants are engaged in manufacturing granule-coated roofings, but, apart from a relatively small output of natural granules by two producers in British Columbia, only one eastern producer makes both natural and coloured granules in Canada, and these only for its own use. The annual consumption is now over 77,000 tons of roofing granules valued at more than $1,600,000, but about 62 per cent of the tonnage is imported. It is thus apparent that the production of Canadian-made granules, both natural and coloured, could be considerably increased. This paper is presented in order to give an outline of the industry and at the same time to point out its difficulties and pitfalls.

Jan 1, 1946

By C S. Szentesy, K Howie

The Rosia Montana gold deposit is located within the æGolden QuadrilateralÆ area in the Apuseni Mountains of Transylvania, Romania. The deposit is situated approximately 85 kilometres north of the regional centre of Deva, within the province of Alba, at elevations of up to 1100 metres above sea level. The Rosia Montana deposit contains a current resource of 344.07 million tonnes at an average grade of 1.3 grams per tonne (g/t) gold (Au) and 6.0 g/t silver (Ag) for a total (measured, indicated and inferred) contained resource of 14.29 million ounces of gold and 67.00 million ounces of silver. The resource was calculated using a 0.6g/t Au cut-off, a 10 x 10 x 10 metre block size and multiple indicator kriging. The low sulfidation style epithermal mineralisation at Rosia Montana is hosted within Tertiary age dacite intrusions and related vent breccias. Mineralisation is generally disseminated and associated with silica, adularia, illite, pyrite and carbonate alteration of host rocks, with minor late carbonate-base metal veins. Precipitation of precious metals is generally considered to have occurred as a result of over-pressurization, boiling and subsequent brecciation. The dacite intrusions are hosted in Cretaceous shallow marine and deltaic shales and slates, which overlie older Paleozoic sedimentary and metamorphic rocks within uplifted sections of oceanic sea floor.

Jan 1, 2002

By M. E. Poad

In 1986, a cooperative effort by the Homestake Mining company, the U.S. Bureau of Mines and the University of Utah was initiated to determine shaft stability while recovering high grade ore in a nearby pillar. Premining finite element simulations indicated the shaft would remain in elastic ground. Six years have elapsed and, despite some initial concern during the first lifts, it appears that the bulk of the original reserve will be safely and profitably recovered. An integrated application of rock mechanics tools from laboratory testing through numerical modelling to mine measurements and observations contributed substantially to the operational success of the project.

Jan 1, 1994

By D. R. Rathburn

Jan 1, 1962

An automatic control system of a longwall roof support is dis-cussed. Hydraulic automatic control systems for longwall roof support have not met all requirements for such systems. Utilization of standard hydraulic elements to form a system that would-comply with all demands leads to a very complicated structure with a large number of hydraulic hoses within and between adjacent supports. So, only simplified systems have been made. This paper describes the multifunctional valve that per-mits realization of any desired logic functions, while maintaining a com-pact form, and analyses its application as a fully hydraulic automatic control system of a roof support.

Jan 1, 1985

By Batric Pesic

Dissolution of gold with elemental bromine was studied by using a rotating disc technique. The main parameters studied were: bromine concentration, stirring speed, pH, and temperature. Additionally, effect of copper, iron, and manganese was also examined. A special attention was paid to elucidate the role of cations, primarily Na+, during gold dissolution. It was found that gold dissolution with bromine was characterized with two pH regions. Below pH=7, gold dissolution was independent of pH, and above this value, gold dissolution decreased with pH increase. Gold dissolution rates were proportional with concentration of bromine. Two regions, diffusional and kinetic, were observed with respect to stirring speed. with respect to the role of Na+, and cations in general, they play absolutely no role during gold dissolution with bromine, unless they are in their lower oxidation state and become oxidized by bromine. In that case they have a negative effect because of bromine consumption.

Jan 1, 1991

By Batric Pesic

Gold dissolution with bromine was studied by using the rotating disc technique. Geobram TM 3400 was used as a source of bromine. The parameters studied were: rotating speed, Geobrom 3400 concentration, pH, temperature, sulfuric and hydrochloric acid concentration, and the concentration of various cations (copper, iron, zinc, aluminum, manganese, potassium and sodium) and anions (chloride, bromide, sulfate, nitrate, and iodide) According to the Levich plot and activation energy, gold dissolution was controlled by a chemical reaction rate. Copper, iron, and manganese in their highest oxidation states, aluminum, zinc, sodium and potassium did not have any effect on gold dissolution rate. The presence of manganous ion dramatically decreased the gold dissolution rate. Kinetic performance of bromine, in the form of Geobram TM 3400, was compared with performance of cyanide and thiourea.

Jan 1, 1990

By Batric Pesic

Dissolution of gold with sodium bromate solutions of various compositions was studied by using a rotating disc technique. The role of bromide ion, acid and externally added bromine was examined. It was found that sodium bromate could not dissolve gold in the absence of either acid or bromide ion, or both. When acid was absent, no bromine necessary for gold dissolution could be produced. When bromide ion was absent, formation of soluble gold bromide species, AuBr,-, was not possible. Bromate concentration had a complex effect, and it was dependant on bromide ion concentration. For fixed initial bromide ion concentration, gold dissolution rate increased with sodium bramate concentration increase until certain level, beyond which further increase of bromate concentration decreased the gold dissolution rate. The negative effect of bromate was explained by the depletion of necessary bromide ion. Sulfuric acid concentration effect was a function of initially present bromine.

Jan 1, 1992

By C. F. Cornell, R. C. Emmett, D. A. Dahlstrom

FOR many years the disk-type and cloth-covered drum filters have found widest application in liquid-solids separation, which uses continuous filters. The disk type is less expensive, occupies less floor space per square foot of filtration area, and re- quires negligible down time for filter media changing. However, because filter cloth is billowed out by the blowback in the cake discharge, it is very short-lived if the scraper blades are set too close. Consequently cake weight is very important in assisting cake discharge, which normally necessitates a minimum cake thickness of 3/8 to ½ in. Also, the vertical position of the disks eliminates the possibility of efficient cake washing for removal of soluble values. The disk-type filter is generally limited, therefore, to applications that require no cake washing and form relatively thick cakes within the normal range of filter cycle times. The conventional cloth-covered drum filter is a more flexible unit, permitting wider variation in the percentage of cycle time devoted to cake formation, dewatering, or washing, as required by the application. Thinner filter cakes can be discharged be- cause a horizontal line across the filter medium at the location of the scraper blade is equidistant from the edge of the blade at all points. The scraper blade therefore may be set a short distance from the filter medium or, where wire winding is not used, a floating scraper can be utilized so that the contour of the cloth can be followed. The drum filter is generally employed when there are difficult filtering slurries with resultant thin cakes or when cake washing to recover soluble values must be practiced.

Jan 2, 1958

By P M. Hancock, Associates

Lacustrine sediments, hydrothermal explosion breccias and spring precipitates deposited 5200 - 1800 years BP as a result of geothermal activity at Lake Rotokaua, contain New Zealand&apos;s largest known sulphur reserves. Current drill indicated reserves are 2 600 000 tonnes of elemental sulphur, assuming a ten per cent (dry basis) cut-off, contained in some 17 000 000 tonnes of ore with an average grade of 214.0 per cent (dry basis) sulphur. Additional inferred ore containing 500 000 - 900 000 tonnes of sulphur has yet to be prospected by drilling. Geological factors will be important in exploitation of the deposit, particularly the extent and disposition of the orebody, sulphur grades and distribution, physical characteristics of the ore, permeability and stability of the overburden and the nature and extent of geothermal activity in the area. Trials to date indicate that Frasch mining and possibly opencutting are unlikely to be successful mining methods. Further mining feasibility studies will be required to ascertain the most likely mining system for the deposit.

Jan 1, 1984