Search Documents

By Milnor Roberts

WAR struck the mineral industry of Washington with cross currents that produced a peculiar result. The State's production of coal, industrial minerals, and metals for 1941, valued at $28,507,282, was increased in 1942 under war pressure to approximately $35.000,000. Meanwhile a tremendous demand had arisen for men to construct airfields and many other large projects for the Army and Navy in Washington and Alaska, and Government plants for the mineral industry costing $140,000,000 or more, as well as a call for employees in the U. S. Navy Yard at Bremerton, the sixty shipyards, the four Boeing airplane factories with many auxiliary shops, and hundreds of other plants turning out war materials. In spite of an influx of nearly 300,000 people, causing an increase of 17.1 percent in the population since 1940, according to the Census Bureau, the State clearly is still engaged in an unusual amount of war production in proportion to its population. A large proportion of the workers have been drawn from the mineral industry to the war plants, whether through motives of patriotism, high wages, or, in the Boeing plants at least, the glamour of the operation

Jan 1, 1944

Australian coals tend to be young in geological age and high in ash by world standards; preparation of the coal before marketing is almost universal. On the basis of float and sink data from 39 locations in the Eastern Australian coalfields, the coals are placed in four categories representing increasing difliculty in their washability characteristics. These seem to be related neither to the geological age nor the geographical position of the deposit and Hunter Valley coals, for example, span all categories. The influence of crushing on the washability of Australian coals is briefly considered and from limited data it is concluded to be appreciably smaller than for British or North American coals. A strategy for the float and sink analysis of Australian coals is proposed and the influence of washability characteristics on current trends in the selection of separating processes for coking and steaming products is discussed.

Jan 1, 1979

At Great Boulder Gold Mines Ltd. a number of attempts were made to remove water soluble copper and iron salts from calcined pyritic concentrates but variou~ problems arose and the methods were abandoned.A method of rapid washing has been developed and although some problems still exist a workable process was established which resulted in substantial savings of reagents used for the cyanidation of calcine.INTRODUCTIONIn the Great Boulder flowsheet crude ore is ground in cyanide solution, then thickened, agitated and subjected to two stage filtering. Secondary filter discharge is pulped with flotation circuit water, gassed with sulphur dioxide to precipitate soluble gold and activate pyrite, and after the addition of copper sulphate and xanthate, the pyrite and tellurides are recovered by flotation. Flotation tailings are thickened and pumped to the disposal area and concentrates are calcined in Edwards roasters. Calcine is washed to remove water soluble copper and iron salts and the washings pumped to the flotation section where the copper is used as an activator. The washed calcine is cyanided and returned to the crude ore circuit via the thickeners. Solution for precipitation in the Merrill Crowe is drawn from the crude ore thickeners.Prior to the introduction of calcine washing the calcine contained 7 lb/ton copper of which approximately 60 per cent was water soluble. It also contained approximately 90 lb/tol'l of water soluble iron salts. Both the copper and...

Jan 1, 1964

By C. D. King

THE key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of IOO per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. I and No. 2 blast furnaces at Rankin, Pa., Carnegie- Illinois Steel Corporation. Clairton By-Product Coke Plant And Coal Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width. These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving 16,800 tons to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1944

By C. D. King

THE key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades' of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of 100 per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. I and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. CLAIRTON BY-PRODUCT COKE PLANT AND COAL WASHER The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width. These ovens also differ in height and length. The present coal washer has a daily capacity of- approximately 14,000 tons, leaving 16,800 tons to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1943

Most mines in the Bundamba, North Ipswich, and Rosewood districts of the West Moreton coalfield of south eastern Queensland have installed washing plants during the last five years. Many problems were encountered in their installation, including the small size of washing plant required in many cases, the economical minimum ash content under present and future market requirements, production from a one-product washbox of large and small coal of quality to satisfy both markets, measures to avoid adding unnecessary moisture to the washed slack coals, and excessive middlings in some coals or soft clay in others.INTRODUCTIONIt was fortunate for Brisbane, which was to become the capital of a new State, Queensland, in 1859, and grow into a city of over half a million people by the time of its centenary, that coal was found in abundance almost on its doorstep near Ipswich, the first mine being opened at Redbank in 1843. This was followed by the opening of many more mines in that district and, some 40 years later, in the nearby Rosewood district where high-volatile gas coal was produced (Fig. 1). These discoveries ensured a supply of reasonably priced coal (currently about 85/- per ton delivered) in Brisbane, but the quality is inferior to that of other coals mined in Queensland beyond economic range of Brisbane.Various factors led to an increase in the average ash content of the West Moreton coals during and after the war. Between 1940 and 1952 the gasworks coals rose in average ash from 13 8 per cent to 23·9 per cent and the powerhouse coals from 17·1 per cent to 27·1 per cent. This drift was arrested by the installation of 28 screening and picking plants from 1952 onward, but it became obvious that mechanical cleaning of the coals was essential due to the competitive market for coal and the worsening quality of reserves.

Jan 1, 1963

By AIME AIME

The Washoe plant, 1 in Anaconcla. Mont., together with the local street-railroad, ranches a. foundry and machine-shop a brick-plant and the Montana hotel, form a property under one management; to which should be added the mines in Butte owned by the company, from which part of the ore-supply of the plant comes. The Anaconda Copper Mining Co., controlled by the Amalgamated Copper Co., was reorganized under the laws of Montana in 1893. A map of the plant, showing the numerous departments and illustrating the details of tracks, pipe-lines, and charging-stations for compressed-air locomotives, is given in Fig. 1.

Jul 1, 1906

One of the very simplest losses to overcome, and at small expense, is belt slip. To show the extent of the loss of money through slipping of the main belt alone, a chart, supplied us through the courtesy of the Cling-Surface Co., Buffalo, N. Y., is shown herewith, upon which this is easily ascertained. By glancing up and down column "D" of this chart it is evident that the "Cost of Avoidable Belt Slip per Year in Dollars" may vary all the way from the smallest sums into the thousands of dollars. Roughly, 2 per cent. of the potential power in the driving pulley of the engine is represented by "belt creep." Its loss is unavoidable because of the elasticity of the belt. This has been recognized and provided for in the chart, so the reader can go ahead and connect known values, while the intersection with column "D" gives the avoidable money loss. Simply zig-zag across the chart twice with a straight edge, as shown by the dotted lines and the money loss is immediately found. Thus if the total belt slip is 6 per cent. (column A) and the cost of coal per ton is $4 (column B), run a straight line through those two points and locate the intersection with column "C." Then from that point of intersection run over to the tons of coal burned per year (which in this instance has been stated as 1000 tons) and the cost of avoidable belt slip per year is shown by column "D" as being $160. To give a clear idea as to the meaning of "Total Belt Slip Per Cent." let us take an example. You find by means of a revolution counter that a given driven pulley is rotating only 940 times per minute. You figure that without slip it should rotate 1000 times per minute; 60 revolutions per minute, therefore, are absolutely lost. Dividing this 60 by the r.p.m. that pulley should make you get 0.060 or 6 per cent. which is the "Total Belt Slip." After having made this determination, it is a simple matter to apply it to the chart as has been done and determine the money loss per year due to such slip.

Jan 4, 1918

THE power requirements of the Mount Lyell Mining and Railway Company at Queenstown, Tasmania, have, since the inception of smelting operations in June) 1896, been derived continuously from the extensive forests in the watershed of the Queen River, adjacent to the works, the fuewoodbeing of good quality, mainly composed of myrtle or beech (Fagus Ounninghami), eucalypts, and manuka (Leptospermum ericoides). The country is very rugged and mountainous, indented by numerous ravines and gullies, and intersected by, many creeks, which are subject to periodical floods, under the influence of a heavy and persistent rainfall, which averages about 110 in per annum. The areas so far exploited aggregate a total of about42 square miles, and this denuded country gives promise of ultimately becoming very valuable pastoral ground for cattle-raising. The tonnage of wood yielded per acre varies from 40 to 100 tons on stack measurement of 80 cubic feet per ton, 60 tons per acre being considered a good average yield. The gross amount...

Jan 1, 1910

By Murray Gamble

A new type of groundwater cutoff wall has been developed at the University of Waterloo. The Waterloo Barrier? is a steel sheet piling system that incorporates a sealable cavity at each interlocking joint. In order to prevent leakage through the joints, the sealable cavity is flushed clean and injected with sealant after the installation of the piling. The installation and sealing procedures of the Waterloo Barrier? system allow for a high degree of quality control resulting in a very low permeability cutoff wall. Based upon field installations, the bulk wall hydraulic conductivity of the Waterloo Barrier? ranges from 10-8 to 10-10 cm/sec. Recent case histories are presented in which Waterloo Barrier? vertical cutoff walls have been used to prevent the off-site migration of contaminated groundwater or soil gases. In some instances, the Waterloo Barrier? system was used in combinations of applications such as preventing the migration of contaminants, redirecting the flow of groundwater, providing structural shoring for soil excavation and aiding in site de-watering processes.

Jan 1, 1997

By S Hanke, J Burden, P Spies

The Waterview Connection will complete Auckland’s long-planned Western Ring Route, a 48 km north-south motorway alternative to State Highway 1 that bypasses the central city to the west. The project involves construction of 5 km of new motorway – half of it underground in tunnels – to connect the Southwestern (State Highway 20) and Northwestern (State Highway 16) motorways.The Western Ring Route will link the major population and industrial centres of Manukau, Auckland and North Shore to give the region the connected and resilient strategic road transport system it needs to underpin economic growth and sustainable development. It will also provide a direct motorway link between Auckland’s central business district (CBD) and international airport.The project involves construction of twin 2.4 km driven tunnels with an outside diameter of 14.41 m beneath residential suburbs, a major arterial road and a rail corridor. Enabling works began in January 2012 while tunnel construction using an earth pressure balance (EPB) tunnel boring machine (TBM) began in November 2013.This presentation introduces the Waterview Connection project, its role in the development of the Auckland motorway network, its procurement process, the alliance delivery model and an overview of the project’s design features and construction progress to date.Design and construction highlights of the presentation include the TBM start-up, turnaround and breakthrough arrangements as well as the experience gained during the first tunnelling drive. The presentation also covers an innovative process developed for invert construction behind the TBM that is independent of tunnel excavation.CITATION:Spies, P, Burden, J and Hanke, S, 2014. The Waterview Connection Project – progress to date, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 519–540 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J. Buckle

"Recognition of the diamond potential of the Wawa subprovince was initially determined from regional data using a kimberlite model. The world’s largest stable Precambrian craton, the Superior Province, is considered to be favourable for the emplacement of diamondiferous kimberlite. The Wawa area is located near the intersection of intra-craton structures visible in the regional magnetic data.The Enigma project is located north of the town of Wawa in northern Ontario. From field evidence and background research, it became obvious that in the Wawa area there were at least two potentially diamond-hosting events, Archean lamprophyric volcaniclastics and Proterozoic kimberlites. The host lamprophyric rock does not contain the classical KIM signatures. However, to complicate the Enigma, stream sediment samples within 200 m of the diamond-bearing lamprophyre produced a typical suite of kimberlite indicator minerals.The micro- and macro-diamond content of the Wawa lamprophyric volcaniclastic rocks is typically 0.2 ct/t to 1 ct/t, although it can be higher locally. The economic diamond potential of these Archean dykes, sills and irregular lamprophyre bodies is still under-explored (Kaminsky, 2002, unpubl.). Oasis Diamond Exploration is currently exploring the area using geophysical, geochemical, and geological data."

Jan 1, 2002

By M. Fiset, D. Belley

"To better understand the wear process of various materials that may be used as blades on snow removal equipment, the first step is to evaluate the influence of the load applied and the moving speed on road wear rates of one type of steel and three types of polymers. While the behavior of steel conforms to Archard's law, wear rates of polymers increase to a power of ex of the load applied according to a model implying that the wear of these materials is due to fatigue. The wear rate of some of the polymers varies considerably in terms of speed, unlike the steel. The wear resistance of some of these polymers outclasses the steel tested as long as the speed is not too great. They, therefore, present interesting alternatives for snow removal on more fragile surfaces such as sidewalks and zone made of inter-block slabs.IntroductionSince the dawn of the Industrial Revolution, the massive use of machines has brought with it a number of different problems regarding wear. Snowplowing roads, parking lots and sidewalks is an activity that generates enormous expense in a country such as Canada. To better understand these wear processes and in the hope of stimulating new approaches designed to reduce the costs related to this sector of activity, this paper presents the behaviour of several materials (steel, polymer and rubber) as they wear on an asphalt-fines matrix surface lubricated with water. Also discussed is the effect of various parameters such as the load applied and speed."

Jan 1, 1990

By R P. Douglas

During 1955, Cominco commenced an exploration pro-gram in northern New Brunswick; in the following year, what is now the Wedge mine was discovered. The mineralization is mainly pyrite, with associated chalcopyrite and minor amounts of sphalerite and galena. The property was brought into production at 750 tons per day in early 1962. The ore is trucked 10 miles to the Heath Steele concentrator, where a copper concentrate grading about 19.5 per cent is produced and shipped to the Japanese markets through the port of Dalhousie, New Brunswick. Introduction THE Wedge mine, owned by The Consolidated Mining and Smelting Company of Canada Limited (Cominco), is located in the Newcastle-Bathurst area of New Brunswick. It is 42 miles by road northwest of Newcastle and 37 miles southwest of Bathurst (Figure 1). The mine is located on the north side of the Nipisiquit river in one of the more mountainous areas of the Province, the local relief rising to 1,500 feet above sea level. There is an almost complete forest cover of mixed hardwoods and conifers -the val-leys and hillsides being covered by balsam, spruce and pine, the swamps by cedars and black spruce and the highlands by mixed hardwoods.

Jan 1, 1965

By Q Yu, G Ren, Z-Y Chen, J Yang

The wedge shape theory of the rock fragmentation range in bench blasting is presented according to the dynamic characteristics of rock fragmentation by blasting in open pit under the condition of hole-by-hole initiation. The finite element software ABAQUS was used to analyse the rock fragmentation mechanism. The rock mass stress contours, crack propagation and damage evolution of different moments were obtained. The results showed that the wedge shape theory of blasting is closer to the rock fragmentation in hole-by-hole blasting and is useful to the design and calculation of charge weight.CITATION:Yang, J, Chen, Z-Y, Yu, Q and Ren, G, 2015. The wedge theory of borehole charge design for bench blasting and its numerical simulation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 169–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By F. F. Sharpless

ARRIVING at Davis Junction, after leaving Portland, we expected to wait for an hour and a half, but found the superintendent of motive power of the Southern Pacific, Mr. Williams, waiting for us with a car, and were immediately taken aboard this and whisked off to Sacramento. After dinner, we were taken to the railroad shops to see their work in reclaiming scrap steel. We saw them draw off the slag from the electric furnace, and later make a casting. At about 11 o'clock, we took the train for Reno. A delegation of the Nevada Section, with Mr. Kirchen and Mr. Rives at its head, met us at the station. Immediately after breakfast, we started for the property of the Comstock Mines Co., where General Bulkeley Wells was to be our host. We had a de-lightful ride out to the mines and through the old city of Virginia, or through what was left of that old city, reaching General Wells' camp at about 10:30. This contains the newest thing in cyanidation and a remarkably fine iron and concrete mill building. After a trip underground, we were called to luncheon, where about 250 sat down. The afternoon was spent in the mill, and we were taken to Gold Hill, which is a part of Virginia City, for dinner, again as the guests of General Wells, who made a consummate toastmaster. Governor Emmet Boyle was the first speaker; he was followed by President Dwight, and then came President William Sproule of the Southern Pacific. A song, "The Engineer," was followed by Senator Key Pittman, Professor Jones of the State University, Mayor Stuart of Reno, and ex-Senator Charles Hend-erson. The president of the Western Pacific and the president of the Pacific Coast Line were there, also many notable operators of Nevada and California.

Jan 11, 1922

Comalco Limited has recently completed construction of a $50 million kaolin plant at the site of its bauxite mining and industrial minerals operation at Weipa. The plant will produce 100,000 tonnes per annum of coating grade kaolin for the paper industry. Comalco produced the first coating kaolin from the deposit in 1979 on a trial basis. Since then a variety of quality coating grades with specific particle size distributions and brightness values have been prepared. Extensive drilling and bulk sampling of the deposit over eight years has shown that the ore body is large and of a high grade suitable for the production of premium quality coating kaolins. The processing plant technology was developed by Comalco in association with the European kaolin and equipment producer Amberger Kaolinwerke GmbH (AKW). The Weipa kaolin plant is the first of this size to be built in the Pacific Basin region and it will offer the region's paper-coating mills a stable and reliable source of high-quality kaolin, shipped from an established bulk loading port. The paper provides an overview of the development of the kaolin investment the nature of the production process and details the

Jan 1, 1986

Comalco Limited has recently completed construction of a $50 million kaolin plant at the site of its bauxite mining and industrial minerals operations at Weipa. The plant will produce 100,000 tonnes per annum of coating grade kaolin for the paper industry.Comalco produced the first coating kaolin from the deposit in 1979 on a trial basis. Since then a variety of quality coating grades with specific particle ize distributions and brightness values have been prepared.Extensive drilling and bulk sampling of the deposit over eight years has shown that the orebody is large and of a high grade suitable for the production of premium quality coating kaolins.The processing plant technology was developed by Comalco in association with the European kaolin and equipment producer Amberger Kaolinwerke GmbH (AKW).The Weipa kaolin plant is the first of this size to be built in the Pacific Basin region and it will offer the region's paper-coating mills a stable and reliable source of high-quality kaolin, shipped from an established bulk loading port. The paper provides an overview of the development of the kaolin investment, the nature of the production process and details the project management procedure used for the design, construction and commissioning of the plant. Three areas of significant interest, the gas turbine fired pray dryer, the moving bridge shiploader and the use of aerobelt conveyors on the project are detailed.

Jan 1, 1988

By Michael B. Cortie

The young field of nanotechnology has as its objective the design and construction of useful devices made of nanoscale materials. Objects or structures which have at least one important dimension in the range 0.5 to perhaps 50 nm may be considered to be in the nanoscale domain. These sizes lie far below the 200 nm or so that can be resolved with an optical microscope, and are closer in size to the 0.3 nm diameter of individual atoms. Nanotechnology, which is the study and exploitation of these tiny structures, is attracting keen interest at present. The excitement is motivated by the observation that control of matter at the nanoscale holds the promise of faster computing, better medicines, and smarter materials. In this paper, the physical phenomena on which this optimism is based are broadly discussed and explained. Where appropriate, examples of the rather different and curious properties of gold at the nanoscale are used to illustrate the points covered.

Oct 1, 2003

By Louis R. Hodell

WHEN the drilling of an oil well is completed a permanent opening from the reservoir to the surface must be provided. This is done by lining the hole with pipe, commonly known as casing. In the past, all but a small amount of casing has been run in the hole and joined by threads and couplings. Recently, however, in California, Texas, and Oklahoma, there has been a definite tendency 'to adopt -the welded joint for the following reasons: (1) Plain end casing for welding may be bought for 15 per cent less than thread-and-coupled casing; some of this is offset by the cost of welding the pipe in the hole but a respectable net profit remains.

Jan 1, 1937