Search Documents

By M. Boussuge

Ceramics and refractories have many common constituents and consecutively exhibit several analogous properties. For example, concerning the thermomechanical properties this paper will focus on, the type of creep that can be observed in both materials is often the same (kinematic hardening). Changes in microstructure (phase transformation, dehydration, sintering, crystallisation,...), induced by heating and/or cooling, can also drastically modify the mechanical behaviour of ceramics and refractories. But the coarse granulates, the porosity and the impurities contained in industrial refractories may lead to specific responses of this material to thermal and/or mechanical loadings. In particular, some differences can be observed with technical ceramics in the main type of damage observed in service : diffuse damage in refractories (microcracking) and localised damage in ceramics (macrocracking). In this paper, the possibilities of transferring a part of knowledge from ceramics to refractories will be discussed, in the field of thermomechanical properties : experimental characterization techniques, mechanical behaviour models. Finally, some problems caused by scale effects and by the integration of thermomechanical properties of refractories in the numerical simulation of industrial structures will be evoked.

Jan 1, 2004

By D. Larouche, M. Mardan

Hot tearing is a complex defect in aluminium castings which is produced during solidification when a certain amount of liquid phase remains and weakens tensile resistance of the alloy. In direct chill casting of aluminium alloys, hot tears initiate at the surface of sheet ingots just after the primary cooling zone, where the microstructure is particularly vulnerable. In order to study the hot tearing susceptibility of these alloys, and the effect of grain refiners on their thermo-mechanical behavior , tensile tests were carried out in the semi-solid state ( ~95% solid) and at low strain rates using an apparatus called DCSS, for Direct Chill Surface Simulator. This apparatus, originally developed at Alcan Arvida R&D Centre (ARDC), is an instrumented rig test reproducing the conditions prevailing during the primary cooling stage of the DC casting process. The mechanical behavior of solidifying shells and the hot tear formation under applied tensile loads were measured and the occurrence of hot tearing was observed. Temperature in different locations of the casting, applied load and surface strain were monitored during the tensile tests conducted on aluminum alloys AA5182, AA6111 and AA3104. The microstructure of the tested samples was examined using the optical microscope to evaluate their columnar or equiaxed aspect and their effect on the mechanical response of the alloy. A special emphasis has been given to the evaluation of fractions solid existing in the castings at the start of the tensile tests, taking into account the local temperature, thermal gradient and cooling rates experienced. It was found that excessive grain refiner additions decreased the strength of solidifying shells because of the increased level of porosity induced by easier nucleation of new phases (gas included). It was also observed that cooling rates increased with the level of grain refiner, a phenomenon that was associated to the higher number of contact points obtained with small equiaxed grains. Finally, the concept of a stress based criterion for hot tearing was reinforced by the strengths obtained on not grain refined AA5182 and AA6111 showing similar fraction solid near the surface, but significantly different grain sizes.

Jan 1, 2006

By W. C. Patrick

The Spent Fuel Test-Climax (SFT-C) was con- ducted to evaluate the feasibility of retrievable deep geologic storage of commercially generated spent nuclear-reactor fuel assemblies. One of the primary aspects of the test was to measure the thermomechanical response of the rock mass to the extensive heating of a large volume of rock. Instrumentation was emplaced to measure stress changes, relative motion of the rock mass, and tunnel closures during three year of heating from thermally decaying heat sources, followed by a six month cooldown period. The calculations reported here were performed using the best available input parameters, thermal and mechanical properties, and power levels which were directly measured or inferred from measurements made during the test. This report documents the results of these calculations and compares the results with selected measurements made during heating and cooling of the SFT-C.

Jan 1, 1986

By Xingye Guo, Yeon-Gil Jung, James Knapp, Zhe Lu, Jing Zhang, Li Li

La2Zr2O7 is a promising thermal barrier coating material due to its low thermal conductivity and superior high temperature stability. In this work, Bilayer La2Zr2O7 and conventional 8 wt% yttria stabilized zirconia (8YSZ) coatings were deposited using plasma spray technique. Both singlelayer La2Zr2O7 and double-layer 8YSZ/La2Zr2O7 coating architectures were designed. Thermal cycling and thermal shock tests were used to evaluate coatings’ thermomechanical properties. All La2Zr2O7 coats were delaminated in the furnace cycle test in less than 20 cycles. This is because residual thermal stresses accumulated during thermal cycling. In the jet engine thermal shock (JETS) tests, the SCL La2Zr2O7 and DCL dense 8YSZ/La2Zr2O7 coatings were fully delaminated. In contrast, the DCL porous 8YSZ/La2Zr2O7 coating sample only partially delaminated on the edge. This is because of the porous 8YSZ layer provides strain compliance. The findings will help to propose efficient thermal barrier coating systems.

Jan 1, 2016

By A. Sissing

Paper written on project work carried out in partial fulfilment of M.Sc. (Chemical Engineering) degree Thermophilic bioleaching, conducted at temperatures in excess of 65°C, provides considerable benefit over mesophilic bioleaching, particularly through extending the extent of leaching of base metal minerals such as chalcopyrite. Thermophilic bioleaching is facilitated through a group of micro-organisms known as the Archae, well adapted to extreme environment. In order to maximize the space time utilization of the stirred tank reactor in the thermophilic bioleaching process, it is desirable to maximize the loading of the finely divided mineral phase present while not adversely affecting the microbial performance. In this paper, the effect of the loading of the solid particulate phase on the bioleaching performance of Sulfolobus metallicus was studied in a stirred tank reactor. Emphasis was placed on the effect of the concentration of the finely divided solid phase (35 ? 75 µm). A model system comprised of 3% (w/v) pyrite in the presence of varying quantities of quartzite in the range 0 to 24% (w/v) was used to obtain the different solids concentrations. The bioleaching experiments revealed similar bioleaching performance in the presence of 3 to 18% (w/v) total solids. Above 18% (w/v) total solids (15% quartzite loading), bioleaching was impaired progressively with increasing solids concentration. At the highest solids loading studied of 27% (w/v), bioleaching was still observed. In terms of mass transfer, oxygen transfer potential was not significantly influenced in the bioleaching process over the range of solids investigated.

Jan 1, 2003

By Y. J. Yu, C. D. Zhang, Y. S. Zhao, W. G. Liang, Y. D. Geng, J. L. Bi

"In this study, the coefficient of thermal expansion (CTE) and thermal conductivity (TC) of shale in two perpendicular directions, vertical and parallel to the bedding of the rock, are firstly measured by experiment. The experimental results show that the CTE of the shale in the vertical direction is 1.69 times as much as that in the parallel direction, while the TC in the parallel direction is 1.83 times larger than that of the vertical direction. Based on the no initial strain assumptions, numerical simulations for the thermal cracking in shale are carried out with the obtained coefficients. Using finite element method and thermal-mechanical coupling theory, two fracture mechanical parameters, KI and J-integral of the shale are also analyzed for the shale thermal fracturing. The simulation results show that both KI and J-integral reach the maximum when the fracturing angle equals to 0° in the shale, namely parallel to the bedding direciton. It is also found that the two fracture parameters decrease with the fracturing angle increasing. Additionally, the thermal fracturing effect of the shale is evaluated under a given scenario. The study is significant for shale oil or gas recovery by in situ pyrolyzing method.INTRODUCTIONOil shale is regarded as a kind of unconventional resource that can contribute to production of shale oil and hydrocarbon gases (Rahm & Dianne, 2011). As is known that there is a large deposit of oil shale in China, and present technology for exploiting oil shale still concentrates on open-pit mining, obtaining shale oil by retorting shale on the ground (Li, Tang, Xue, Zheng, & Du, 2014; Qian, Yin, 2008). However, this technology has a bad effect on the environment and leads to severe resource waste for utilizing oil shale. Exploiting oil shale by in-situ method for ‘green mining’ is widely necessary in China (Kang, Wang, Cao, Liang, Chang, & Liu, 2013; Waters, Dean, Downie, Kerrihard, Austbo, & McPherson, 2009; Zoback, Kohli, Das, & McClure, 2012). One of effective method to exploit shale oil is heating oil shale in-situ underground. For instance, the in-situ conversion process (ICP technique) from Shell Company etc. used a direct heating method, and convectional heating oil shale underground by injecting superheated steam from Mining Technology Institute, Taiyuan University of Technology and constructing horizontal fracture in vertical wellbore from Chevron Company use indirect heating method (Chaudhary, Ehlig, & Wattenbarger, 2011; Hazra, Lee, Economides, & Moridis, 2013; Zhao et al., 2010). The convectional heating method contains complicated procedures with phase transition in double-media of fracture-matrix of oil shale subjected to multi-physical fields coupling including stress, fluid and temperature (Zhao et al., 2010). The characteristics of thermodynamics, solid mechanics and seepage of oil shale have been investigated separately (Hopkins, Rosen, & Hill,1998; Kang, Zhao, & Yang, 2008; Yang, Zhao, Kang, 2010; Zhao, Yang, Feng, Liang, & Kang, 2008; Zhao, Cao, Zhao, Lin, & Wang, 2008). However, it is quite difficult to solve constrained problem of each physical parameter in multi-physical fields coupling for oil shale pyrolysis."

Jan 1, 2015

By K. C. Mills, P. N. Quested, A. P. Day, R. F. Brooks

"Methods have been developed to measure the physical properties of molten materials relevant to the fluid flow in high temperature processes. Data for the densities, viscosities and surface tensions of Al-, Ni- and Fe-based alloys are compared with (i) values for the pure metals and (ii) estimated values obtained from models making use of chemical composition of the alloy. Experimental values for metallurgical slags are also given and compared with estimated values.1 IntroductionPhysical property data has proved very useful in improving process control and product quality. For instance, in the continuous casting of steel the viscosity (TJ) of the mould flux is important since it determines (i) the optimum casting conditions, nVc = 2.5±1 dPas (m min-1) where V c is the casting speed and (ii) the level of slag entrapment (which leads to inclusions) in the metal. Thus data for properties like viscosity are exceedingly useful in understanding the process and the problems encountered and the causes of defects and problems.Another interesting development which has helped to increase our knowledge of processes and improve process control and product quality is the development of mathematical models of the fluid and heat flow in the process. These models have been developed to the stage where one of the prime requirements is for good physical property data for the industrial materials involved. Recently, Oxley [1] has shown that the use of reliable, experimental, property values for the commercial alloy in a commercial software package produced a significant improvement in the prediction of casting defects. Thus reliable property data are required for liquid metals but also for (i) liquid slags since many processes involve the use of a slag to refine and protect the metal or to lubricate the mould and (ii) refractories, sand and investment moulds."

Jan 1, 1999

By Yongqi Sun, Zuotai Zhang

Our study investigated the influence of P2O5 and B2O3 on the viscosity and crystallization behavior of Ti-bearing blast furnace (Ti-BF) slags for the purpose of Ti extraction. The investigation of the crystallization behaviors were carried out using a single hot thermocouple technique (SHTT) and the viscosity was obtained by rotating cylinder method. For the viscosity, the results showed that P2O5 substantially increased the slag viscosity. P2O5 is a network-forming oxide, which increased the degree of polymerization of slags and accordingly increased the slag viscosity. However, both of slag viscosity and apparent activation energy for viscous flow remarkably decreased with B2O3 addition. As a typical network forming oxide, B2O3 was introduced into the network and existed dominantly as 2-D structure, BO3 triangular, which caused a simpler structure and a decreasing slag viscosity. As for the crystallization behaviors of Ti-BF slags, both P2O5 and B2O3 enhanced the crystallization trend of rod-shape rutile and suppressed the crystallization trend of dendrite CaTiO3. Therefore the added P2O5 and B2O3 caused the primary phase change from CaTiO3 to rutile. Additionally, it was found that the rod-shape rutile showed a 1-D growth, whereas the dendrite CaTiO3 showed a 3-D growth style.

Jan 1, 2015

By M. Q. W. Jones

This paper presents a compilation of physical properties of rocks from the Bushveld Complex. The database consists of more than 900 measurements each of thermal conductivity and density. The data are well distributed from localities around the Complex and most rock types are well represented. Thermal conductivity and density are shown to vary widely in the ranges 1.8-4.2 W m-1K-1and 2600-4200 kg m-3respectively. Although only 190 heat capacity measurements are available, this parameter is quite uniform for most rock types present, 800-900 J kg-1K-1, except for chromitite, which has a lower average, 750 J kg-1K-1. Rocks encountered in deep platinum mines are particularly well characterized and this has important implications for prediction of mine refrigeration requirements. The heat flux into a semi-infinite region with properties typical of the Bushveld Complex as a function of time is substantially lower than an equivalent model for the Witwatersrand Basin.

Jan 1, 2015

By Ulrich E. Klotz, Gemot Pottlacher, Shahid Mehmood

"Platinum alloys are frequently used in technical applications and in jewellery. Their thermophysical properties such as density, heat capacity, thermal conductivity and surface tension play an important role in casting processes and are required as input data for casting simulation. Scope of this work was to investigate these properties by different methods. Platinum and four alloys namely, Pt96Cu4, Pt68Cu32, Pt50Cu50 and Pt25Cu75 were investigated. Melting range and thermal expansion was measured at fem by DSC and dilatometry, respectively.At TU Graz wire shaped samples were investigated by an ohmic pulse heating technique. This technique allows the calculation of specific heat capacity and the temperature dependencies of electrical resistivity, enthalpy, and density of these alloys in the solid and liquid phase. Experimental results were compared with available literature and data from thermodynamic calculation using the SNOBl database and ThermoCalc.IntroductionPlatinum is a precious element and its alloys are commonly used in jewellery. But Platinum is much more difficult to cast then other jewellery elements like silver or gold, because of its high melting temperature, large shrinkage during freezing, low thermal conductivity, high surface tension, and high viscosity. As a result there arise problems during casting. Hence to resolve these difficulties a detailed study of thermophysical properties of solid and liquid platinum and its alloys is necessary for simulation and casting. The Platinum alloy samples were prepared by vacuum induction melting and casting into copper molds. Rods of 3 mm in diameter and a length of 80 mm were prepared and drawn to wires of 0.5 mm in diameter."

Jan 1, 2011

By F. Kongoli

A computerized thermophysicochemical database is being developed for various processes involved in nickel smelting and converting. This database includes optimized models for slag, matte, liquid and solid alloys in the multicomponent system(s) as applied to batch and continuous nickel smelting and converting processes. This database can be used to quantify the multicomponent and multiphase slag/matte/alloy/gas equilibria, liquidus and solidus surface, tie-lines, solubility and/or losses of nickel and other components in the slag, distribution coefficients, components activities, heat and mass balance, etc. The database also includes optimized models for the viscosity of the slags associated with any of the above processes. Both databases are coupled and this constitutes a very effective method to quantify the effect of each component on several parameters of the smelting and converting processes and to diffuse the confusion that exists in the literature. Several application examples have been given to demonstrate the usefulness of this database for quantitative prediction of the thermophysicochemical properties of the phases involved in actual or developing processes, even in the areas where experiments are difficult or impossible. The considerable cost reduction that results ftom the use of this database as compared to other methods in the improvement of existing technologies or in the development of new ones is discussed along with continuing new developments of this database.

Jan 1, 2002

By D R. L Vedoy, L Botha, S P. Gumfekar, J B. P Soares

Most of the known in-place reserves of oil sands are found in Canada. These oil sands ores are mined using various processes to extract bitumen. The by-product slurry resulting from the extraction process, known as tailings, is discharged into tailings ponds. Fine kaolin clays are an important ingredient of the tailings because they remain suspended in water for many years. Current polymeric flocculation/dewatering technologies use acrylamide-based polymers such as polyacrylamide (PAM), but sediments produced using PAM-based flocculants hold considerable amounts of water due to the formation of loosely-packed flocs. Anionic polymers are better flocculants due to bridging and the charge-neutralisation mechanism. In this paper, we will compare the synthesis of two flocculants: thermosensitive, anionic flocculants and thermosensitive, hydrophobically modified anionic flocculants. The first flocculant is a copolymer of acrylic acid (AA) and N-isopropyl acrylamide (NIPAM), in which AA is the anionic monomer. The second flocculant is a copolymer of NIPAM, AA and the hydrophobic monomer N-tert-butyl acrylamide. We evaluated the dewatering efficiency of 2 wt per cent kaolin using both flocculants by comparing settling rates at different flocculant dosages, charge neutralisation ability and supernatant clarity. To better understand floc formation, we measured the floc size formed by both flocculants at different flocculant dosages. We propose that the hydrophobic monomer in the terpolymer flocculant helps expel water out of flocs, ultimately decreasing the water content in the sediments.CITATION:Gumfekar, S P, Vedoy, D R L, Botha, L and Soares, J B P, 2015. Thermosensitive, hydrophobically modified anionic flocculants for dewatering kaolin clays, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 45–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By H. Wu, V. Izaxon

Intensive ventilation is required during the excavation of a mine opening and the subsequent exploitation of the mineral resources. The exchange of heat between the ventilation air and the rock mass has a major influence on the thermal regime of a mine, especially in the initial segment of the airway. In frozen ground, heat flow into the rock mass from the ventilation air can result in the eventual thawing of the permafrost, which can result in roof-rock instability. This paper presents a mathematical analysis of the dispersion process of ventilation-induced heat by thermosyphons placed on the surface of the mine. The principal uses of thermosyphons in the Arctic are to reduce the ground temperature to prevent potentially unstable permafrost from thawing and to increase the bearing strength of the material. The mathematical model of the physical problem, generally known as "the Stephan problem," takes into account the varying thermo-physical properties of air and the frozen and thawed rock mass, the thermal properties of the freeing fluid in the thermosyphons and the phase change of water. Finite-difference techniques were employed to determine the temperature isotherms around the thermosyphons. It was found that two rows of thermosyphons on a 10- x 10-m grid provide an acceptable design spacing for reducing the ground temperature around the mine airway.

Jan 1, 1997

By Boleslav Taraba, Antonín Taufer

Thermovision monitoring of surface temperature has been examined for the purpose of detection of spontaneous combustion of early stage. Measurements were carried out in bituminous and subbituminous coal mines. It was found that surface temperature heterogenities can be considered as common phenomenon in mine openings. However, the most of the observed temperature heterogenities were not connected with coal spontaneous combustion of early stage. These, so called [non-spontaneous combustion] temperature heterogenities in surface of mine openings were found to be caused by: l. Different conditions of heat transfer between opening surface and air stream; 2. Low temperature (natural) oxidation of coal; 3. Dissipated heat loses of working machine. Sites of early stage spontaneous combustion of coal were characterized by: 1. More significant, local rise in surface temperature comparing with low temperature coal oxidation; 2. Evolution of carbon monoxide with local concentration near the surface of such site more than about 15 ppm (bituminous coals) or 30 ppm (subbituminous coals). INTRODUCTION Mine fires are a serious hazard to life and result in a considerable loss of coal reserves. Thus, great attention is paid to investigation of new methods enabling already early detection of self-heating of coal. The earlier a fire is observed, the easier would it be to deal with. Detection methods used in coal mines are mainly based on: 1. [Mine air analysis]. Changes in composition of mine air are examined. Products of spontaneous heating of coal, not being present in mine air under normal conditions, are considered as indicators of anomalous behaviour of coal (carbon monoxide, unsaturated hydrocarbons) (Mackenzie-Wood and Strang, 1990). 2. [Temperature measurements]. Sites of higher temperature level comparing surroundings are looking for underground using various direct or indirect methods of temperature measurements. This paper summarizes experience from thermovision monitoring, as one of the latest indirect temperature measurement technique, used for the purpose of early detection of self-heating of coal in mine openings. INFRARED THERMOVISION Infrared thermovision device of AGEMA Infrared systems AB (Sweden) was used for the in situ measurements. The constant value of emissivity factor, 0.95, was pre-set as the most probable level of emissivities of coal and rocks in mine conditions.

Jan 1, 1993

By D. P. Patil, B. K. Parekh

Water is the mainstay for beneficiation of fine size coal and minerals; however, it is also the least desirable constituent in the final product. The basic concept of the novel process described in this paper is based on the differential surface heat conduction/ absorption capacity of individual particles, which differs for different species of minerals. When a mixture of fine material is exposed to a radiant energy source, the various solids present in the mixture will absorb heat energy depending on their heat-conducting properties and there will be a difference in the surface temperature of the particles. When this differentially heated solid mixture is placed on a moving belt, which is coated with a low temperature melting resin, the hotter component of the mixture will stick to the belt and relatively cooler particles will stay free on the belt and fall off at the end of the belt run. Experiments were conducted with pyrite, coal, and quartz of 6 × 18 mesh particle size. The goal of the test program was to find the optimum conditions at which there exists a required temperature difference between minerals and coal particles by controlling the operating system variables. Preliminary tests results showed that there is a potential for separating mineral matter from coal using the thermo-adhesive separation technique.

Jan 6, 2022

ABSTRACTFor the binary system copper-lead two relationsEquation 1andEquation 2have been derived for the activities of copper and lead at compositions and absolute temperatures within the liquid region of the phase diagram.These relations give, with greater accuracy than is given by previously published relations, the activity-composition temperature variations for all regions of the phase diagram of interest to metallurgists.These relations are essentially simple forms of the Margules equations but with linear temperature dependence applied to their coefficients. This has been done in such a manner that a phase diagram obtained from these relations agrees well with the data available for this system. The methods of obtaining the relations and constructing a phase diagram from them are both given in detail. The enthalpies and entropies of mixing are compared with those derived by other methods.

Jan 1, 1971

By Robert Roberts

(Butte Meeting, August, 1913.) In order to obtain data on the thermal effect of the blast-furnace jacket and on the water consumption in these jackets a series of tests were run on the 56 by 180 in. blast furnaces at the Great Falls Reduction Department of the Anaconda Copper Mining Co., at Great Falls, Mont. The arrangement of the jacket is shown in the transverse section of one of the furnaces (Fig. 1) on which the tests were made. The nose, spout, and breast jackets have independent water supplies and discharges. The end and side jackets are connected in pairs, as regards water supply, the feed water entering at the bottom of the lower jacket and overflowing into the bottom of the jacket immediately above it, and discharging into an independent overflow pipe for each pair of jackets. Tests were run on the main side and end jackets, the breast jacket, the spout, and the nose. Measurements were taken of the quantity of water discharged, per minute and the rise in temperature of the water in its passage through the jacket. The product of these two results, expressed in the proper units, evidently gives the number of units of heat removed per minute by the water. Sufficient work was done on each type of jacket to determine its behavior under different conditions, and the results from each set of conditions were checked by repeating the work from three to six times. The method used was as follows : The overflow from the jacket to be tested was arranged to discharge at will into a barrel, mounted upon platform scales. The discharge temperature was read just before turning the water into the barrel, and just before turning it back to the sluice; if the test lasted more than a minute, additional temperature readings were taken at 1-min. intervals from start to finish. The elapsed time of running the water into the barrel was, determined with a stop-watch, and this figure, combined with the in-

Jan 7, 1913

The author describes 1. The classification and characteristics of various thick seam mining techniques in various Japanese coal mines. 2. Practices of thick seam mining methods experienced in Taiheiyo Coal Mine. Currently, thick single lift, simultaneous multi lift and non simul- taneous multi lift mining methods are adopted as underground flat thick seam excavations in Japan. These are now reliable and effective in increasing the extraction ratio. At Kushiro Colliery of Taiheiyo Coal Mining Co., these three thick seam mining methods have been used. According to the results, if solidification of the top lift goaf is essential, the non simul- taneous multi lift mining method is the most effective in increasing the extraction ratio without minimising productivity of each lift and it points out that further development of this method is necessary.

Jan 1, 1976

By Sebastien Maillard, Stephane Georges, Thomas Vallee, Stanislas Mauuary

Steel strip manufacturing ever reinvents proposing new grades, requiring to tackle technical limitations of production systems. Primetals Technologies breaks through strip welding by expanding the welder LW21L “Asolid” technology used on low gauges for high-end market such as automotive CAL/CGL. Addressing the usual drawbacks in maintenance, operation and safety of current welding system based on mechanical cutting and CO2 laser welding, the newly developped LW21H “Asolid” technology processes thicker strips up to 7 mm with solid-state laser cutting and welding. This new welder is brought to reality through a scale 1:1 pilot developed, manufactured and tested in Primetals Technologies workshop.

Oct 1, 2019

By V. L. Mitsopoulos

This paper provides a summary of tailings disposal techniques and the improvements that have been made through the introduction of thickened tailings disposal. The general properties and characteristics of thickened tailings are described, as is a design process for selecting appropriate technologies for thickening, pumping, transporting and storing tailings. The factors affecting the selection of an appropriate disposal site and operational considerations for the effective utilisation of tailings storage areas are also documented.

Jan 1, 2006