Search Documents

By Jonathan Matthews

Efficient and effective management of mine tailings is essential for continued successful development of Alberta?s vast oil sands resources. Syncrude Canada Ltd. continues to research novel tailings management techniques in an effort to improve production efficiency and environmental sustainability. During the summer months of 2001, Syncrude Canada Ltd., in collaboration with members of the Canadian Oil Sands Network for Research and Development (CONRAD), conducted field-scale trials of thickened tailings technology at Syncrude?s Aurora mine, north of Fort McMurray, Alberta. This paper provides an overview of the test program including discussion of objectives, test configuration, and program observations. 0Data collected during the field trial indicate that substantial swings in feed slurry composition challenge effective thickener operation. When coarse mineral solids dominated slurry composition, thickener rake torque rose to unmanageable levels. It was determined that the end-of-pipe depositional characteristics of thickened oil sands slurry were generally consistent with present understanding of oil sands tailings slurries. After shear, thickener underflow product exhibited very shallow beach angles and a limited capacity to keep coarser particles in suspension indicating that stacking of ?paste-like? thickener underflow product from a conventional thickener is not practical in an oil sands setting unless process adjustments can be made to increase the underflow density and/or preserve the initial high yield stress of the underflow during transport and deposition. These technical challenges notwithstanding, Thickened Tailings technology offers considerable promise for recovery of warm water from oil sands process tailings.

May 1, 2003

By T. Wisdom, D. Romo, G. Seale, R. Jansen

Thickening remains relatively misunderstood since it is typically near the end of the process and not directly involved in metal recovery. When operating well, thickeners are ignored and left to run independently, the ‘out of sight, out of mind’ phenomena. However, when operating poorly, there is a lack of basic understanding and remedial actions to solve issues are reactionary rather than proactively addressing shortcomings. This series of papers breaks down in sequential order the stepped phases required to gain an appreciation and thorough understanding of the science behind thickeners, and key thickener components, and basic troubleshooting skills. This second paper starts with identifying the different approaches to thickener test work including static and dynamic settling tests followed by high-rate versus paste thickening. Complimentary to test work, the mechanisms surrounding coagulation and flocculation are presented and explained. The basic mechanisms for coagulation and flocculation are discussed to support the different test work approaches and provide the reader with the basic background.

Mar 2, 2022

Thickener Modelling - Incorporating Shear Effects

Sep 13, 2010

By R. J. Smith

Hornestake's Mclaughlin Mine is the first commercial application of pressure oxidation pretreatment of gold prior to cyanidation. Inherent to the autoclave process are several liquid/solid separations. Flocculant consumption represents a significant portion of the consumable reagent costs at McLaughlan. This paper focuses on the efforts of the Operating, Metallurgy and Engineering groups to improve thickener operation and minimize flocculant consumption. An operating philosophy incorporating feed solids control, increasing flocculant dilution water and minimizing flocculant solution shear has resulted in a reduction in 1986 flocculant costs of $0.054/t ($0.06 st) versus 1985 costs. Additional changes are projected to result in a further cost reduction of $0.20/t ($0.22/.st) in 1987.

Jan 1, 1988

By E. J. Roberts

Prior to 1916, thickening was an art, and any accurate decision as to what size of machine to install to handle a given tonnage of a specific ore must have been one of those intuitive conclusions, based on both intimate and extensive acquaintance with thickners and ore pulps. Then in 1916 "knowledge of acquaintance," became "knowledge about" with the publication of the Coe and Clevenger paper.' The unit operation of thickening had graduated to the status of an engineering science. The fundamental similitude relationships for the two major phases of the operation were defined so clearly that batch tests on models as small as liter cylinders could serve to specify protypes as large as 325 ft in diameter.

Jan 1, 1949

By H. Hamza

Oil sand tailings are disposed of in large ponds in which MFT (Mature Fine Tailings, a stable suspension of fine particles in water) forms after many years of settling. Long-term storage of large volumes of MFT is costly to maintain and also poses an environmental liability. The Advanced Separation Technologies laboratory at CANMET Western Research Centre has worked closely with oil sand companies to eliminate MFT generation by applying paste technology to oil sand tailings. In this process the fine tailings are flocculated to produce a thickened material that has the potential to consolidate to a dry landscape, while warm water is recovered and recycled for reuse in the extraction process. This paper presents some results of an extensive technical program involving bench-scale tests for flocculant selection and continuous thickener pilot tests.

Jan 1, 2002

By W. Julian Patron

TREATMENT of the breaker wash-water discharges to remove the suspended particles of finely divided material is usually most efficiently and economically accomplished in settling or thickening tanks. The purpose of these tanks is to separate the excess water from the solids by sedimentation whereby the solid particles suspended in the water are thickened by the force of gravity. The water overflowing these tanks is either reused for coal cleaning or discharged directly to the streams. The settled solids, which are in a relatively concentrated condition, forming a sludge or thick pulp, can be disposed of by pumping to a storage dam, by slushing into mine workings, by processing for recovery of coal, or filtering by vacuum or centrifugal means and discharging with the breaker refuse. The scope of this paper will be limited to the discussion of settling and thickening equipment, the factors that influence the settlement of solids, and a brief description of tests that can be made to determine the size of settling facilities required for any particular condition. The practical application of sedimentation to the treatment of coal falls into two groups, one of classification or hydro- separation, and the other of clarification and thickening. Classification may be employed to prepare a relatively low- grade fuel, which can be used as is or can be further processed separately. Clarification and thickening is employed where the primary objective is to recover a relatively dewatered solid and return a satisfactorily clear water to breaker or streams. When a stream of water flows across a tank, the time required for a particle to travel from the feed inlet to the overflow must be a little greater than that required for the finest particles or flocs in the feed to settle out of the stream. OPERATION AND TYPES OF SETTLING EQUIPMENT Theoretically, the liquid in a settling tank should rise at a more or less constant rate throughout the area of the tank Under these conditions the rising velocity of the water must be less than the settling rate of the finest particles if clarification is to be obtained. When classification of particles is to be made in the tank, the overflow velocity must be greater than the settling velocity of the particles that are to be removed with the tank overflow. The performance of a settling tank, then, depends on the settling rate of the solids and the current velocities in the tank. The oldest types of sedimentation employ intermittent types of settling tanks of any convenient shape. Means are provided for filling the tank with pulp and allowing it to settle until quiet, for moving the clean liquor and for removing the thickened sludge. The operation is necessarily intermittent but a sufficient number of tanks is employed so that a continuous flow of clear water is maintained. Continuous methods for the sedimentation of slurries were developed in the metallurgical industry. Cones from which settled solids were discharged by gravity

Jan 1, 1946

By G Hart

As the iron ore/magnetite boom gains momentum, it is particularly important to question established past trends and explore the potential of alternative design options. Traditionally, ‘rule of thumb’ methods have been used to size dewatering equipment. Greater consideration needs to be given to technological advancements and specific throughput testing of each ore body type based on innovative developments.This paper will describe how an innovative approach resulted not only in significant savings in capital cost and site work hours but also delivered a truly optimised design for the thickener duty at Karara. Test work also played a crucial role and a comprehensive test work program on the ore samples showed the scale-up benefi ts of new technology in thickener designs. Working closely with the Karara team during the laboratory testing proved the old sizing theories for iron ore/magnetite processing have been superseded with the knowledge and results of the industry’s newest feedwell technology. Increased solids flux and rise rates in the testing process proved very successful, resulting in signifi cantly reduced thickener sizes and lower capital expense.Mechanical design considerations such as removal of underflow and pump access led to a preference for an above-ground thickener confi guration, and the economics of a completefabrication and installation package favoured steel construction for the thickener units.The ultimate choice of the bolted/fl anged tank methodology provides both economic and timely solutions for the site installation including reduced man power and quick and safe site-work. A benefits comparison between this design and other fabrication and installation procedures will also be analysed in the paper.

Jul 11, 2011

By Rick J. Chalaturnyk

In Alberta, oil sands bitumen is utilized for synthetic crude oil production by surface mining, bitumen extraction followed by primary (coking) and secondary (catalytic hydrotreating) upgrading processes, or by catalytic hydrocracking and hydrotreating replacing the primary and secondary upgrading processes. Oil sands tailings, composed of water, sands, silt, clay and residual bitumen, is produced as a byproduct of the bitumen extraction process. Several processes have been proposed for the treatment of oil sands tailings, resulting in different recovered water characteristics, consolidation rates and consolidated solid characteristics, which may have effects on the performance of the overall plant operations. A process for the same purpose has been developed by treating the oil sands tailings with CaO lime and CO2 and thickening it using a suitable thickener. In this process a release water of acceptable properties is recovered in a short retention time, which makes it possible to recycle the recovered water, probably after a reconditioning treatment, as warm as possible to improve the thermal efficiency of the extraction process. The paper presents the theory and laboratory results for the CaO and CO2 thickening of low temperature flotation tailings. The water release rates, segregation potential of the thickened underflow and chemistry of the release water are shown and discussed. It is suggested that in using the proposed process, the thickened tailings underflow can be disposed for further consolidation, or combined with the coarse tailings to produce Blended Composite Tailings, corresponding to the Composite Tailings process in the existing hot water extraction plants.

May 1, 2002

By Jonisha P. Pollard

In restricted vertical working heights such as low-seam coal mines, workers are forced to assume kneeling or squatting postures to perform work. These postures are associated with increased risks for the development of significant knee pathologies such as meniscal tears and osteoarthritis [1,2]. Previous research has shown an increased applied knee flexion moment when kneeling in high flexion [3]. However, these models have been applied to flexion up to 140° which neglects contact between the thigh and calf which occurs beyond 140°. In addition to thigh-calf contact, when kneeling near full flexion there may be additional contact between the heel and gluteal muscles. To the author?s knowledge, heel-gluteus contact has not been previously investigated, but thigh-calf contact has received some attention. Zelle (2007) reported thigh-calf contact forces up to 30% bodyweight (BW) [4]. Zelle (2009) reported decreased knee forces when accounting for thigh-calf contact [5]. Caruntu (2003) reported erroneous force and moment estimations when thigh-calf contact was neglected from models to determine muscle and ligament forces [6]. In this study thigh-calf and heel-gluteus contact forces were quantified to determine their effect on the externally applied flexion moment in high flexion.

Jan 1, 2009

By Ljudmil S. Grigorov, Eric Forssberg, Hanumantha Rao Kota, Robert J. Pugh, Lidia B. Alexandrova

"We have used the microscopic thin balance developed by Scheludko at al. (1970) technique to study the stability and interactions within the thin film between the silica surface and air bubble with (i) a long chain C10 amine and (ii) a cationic/anionic surfactant systems consisting of mixtures of a long straight C10 chain amine with long straight chain C8, C10 and C12 sulfonates. It was found that the mixed surfactants caused lower contact angles, lower rates of the thin aqueous film rupture and longer film lifetime, compared to the pure amine system.This behavior was explained by the initial strong adsorption of positively charged interfacial complexes from the mixed surfactant system at the air/solution interface followed by adsorption at the silica interface. It was also shown that the chain length compatibility between the anionic and cationic surfactants controls the strength of the interfacial complex, determining an inhibition in the thin film rupture and dewetting of the film. The rupture mechanism was explained by an earlier established heterocoagulation mechanism between the positively charged air/solution interface and the solution/silica interface which remained negatively charged. The formation of the interfacial complex at the air/solution interface was confirmed by using surface tension data."

Jan 1, 2003

By Ljudmil S. Grigorov, Eric Forssberg, Hanumantha Rao Kota, Robert J. Pugh, Lidia B. Alexandrova

"The effects of mixed collectors on some physicochemical parameters (thin film lifetime, kinetics of expansion of the three-phase contact, equilibrium three-phase contact angle and surface tension) involved in the elementary act of flotation were investigated experimentally.We have used the microscopic thin balance developed by Scheludko et al (1970) to study the stability and interactions within the thin film between the silica surface and air bubble with (i) a long chain C10 amine and (ii) a cationic/anionic surfactant systems consisting of mixtures of a long straight C10 chain amine with long straight chain C8, C10 and C12 sulfonates at 1:1 molar ratio. The experiments were performed at a range of concentrations at pH 6.5. The equilibrium contact angle was measured with a microscope technique using the modified Mingins-Sheludko method (Mingins and Scheludko, 1979). The surface tension was measured by the method of Wilhelmy (Adamson, 1960). It was found that the mixed surfactants caused lower contact angles, lower rates of the thin film rupture and longer film lifetime, compared to the pure amine system."

Jan 1, 2003

By Edward M. Jacobs

In some ore grinding circuits it is desirable to make separations purely on size. The normal choice for this is vibrating screen equipment. Developments in screening process technology have led to improvements in the capacity and efficiency of vibrating screens, through the adoption "Thin Layer Wet Screening". This process can reduce recirculating loads and equipment requirements in the ore grinding circuit.

Jan 1, 1985

By E. A. Gulbransen, W. S. Wysong

THE behavior of molybdenum and its surface oxides in oxidizing and reducing gas atmospheres and in high vacua at elevated temperatures is a question of scientific and technical importance The use of molybdenum as a metal or as an important component in alloys in oxidizing atmospheres at elevated temperatures has been limited because of the unprotective nature of its oxide film and the volatility of this oxide at moderate temperatures. This communication will present results of a vacuum microbalance study 1,2 of the following problems. (11) the oxidation kinetics in the temperature range of 250° to 450°C; (2) the reduction with pure hydrogen of thin oxide films formed on molybdenum; (3) the volatility of the thin oxide films, and (4) the vacuum oxidation of molybdenum at high temperatures. Molybdenum is an interesting metal to study for the following reasons: (I) although the oxide-to-metal-volume ratio is greater than one, the metal is not considered protective; (2) the metal oxidizes readily at temperatures of 250°C and higher; (3) the oxides of the metal are reduced at temperatures as low as 500°C by pure hydrogen; (4) the oxide MoO3 melts at 795°C; and (5) the oxides of molybdenum are volatile at moderate temperatures. The following variables are studied in the oxidation kinetics. time, temperature, pressure, surface preparation, surface area, concentration of inert gas in the lattice, cycling procedures in temperature, vacuum effect and high temperature vacuum oxidation The general interpretation of many of these factors has been previously discussed. LITERATURE The oxidation of molybdenum has not been studied critically. Although" many studies have probably been made on the kinetics of the oxidation process, none has been reported in the literature available to us. The crystal structures found in the oxidation of molybdenum have been studied by Hickman and Culbransen 4 Their results showed that MoO2 is the oxide which is stable in contact with the metallic subgtrate throughout the temperature range 300 to 700°C. As the film thickens in the low temperature range, MoO3 becomes predominant on the surface. Above 400°C, Mo03 is no longer observed, Mo02 being the only oxide found. Hagg and Magneli5 have shown from an X ray study that the a-phase, orthorhombic MoO3 is stable up to 1050°C. Two other phases, ß and ß', with compositions close to Mo02 90 are also obtained The formula for the ß phase is not given but that of the ß' phase is defined as Mo9026. The ß' phase is found to be built upon a monoclinic unit cell. A -?-phase is isolated from a preparation M00275 heated for 17 hrs at 670°C. This phase is

Jan 1, 1947

By R. B. Dunn

Whilst coalmining in the United Kingdom has been synonymous with longwall mining practice there have been changes in recent times which have enabled not only an extension in the length of the face to be worked but also in the ability to extract both thick and thinner seams. Additionally the industry has taken a positive view in the extension of retreat methods of extraction applied for different reasons both to particularly thick and specially thin seams. To permit development of a flexible programme to meet these diverse needs, it has been necessary to design machinery along with mining systems specially suited to these requirements. In reviewing current UK thinking special emphasis is made on the extraction of thinner seams generally of higher quality coal at moderate depths with a commentary on some recent results.

Jan 1, 1979

By B Roache

Ground support installation into the face of development headings has become an accepted practice at many Australian hard rock mines. Ground support is installed in the development face to reduce personnel exposure to rockfall while conducting work tasks such as marking up, installing lifter tubes, charging, and face sampling. The ground support system installed in the face is typically friction bolts and mesh. This support system can be effective at reducing rockfall occurrence, but it also increases the cost of development per metre, in terms of capital for the ground support, jumbo and operator capital allocation and the installation time slowing each drill and blast cycle. Other issues associated with meshing and bolting the development face include management of rock bolts and mesh sheets in the fired dirt of every cut, damage to services such as vent duct, geometry issues when installing ground support onto irregular development profiles and operator error. Fibrecrete installation onto the development face for support is an option considered by many mines, but it can be difficult to manage due to the removal of visual indications of misfires and slowing the mining cycle due to the wait time for fibrecrete curing. The use of Thin Spray Liner (TSL) products in underground hard rock mines has been relatively infrequent in the past, mainly due to issues with cost, health and safety, and liner strength. Kanmantoo Mine investigated the use of TSLs for the purpose of development face support, while collecting data on the costs and practicalities associated with their use. Several TSL products were trialled and a preferred TSL product was selected for use as face support. Cost savings, drill and blast cycle timing improvements and other benefits were achieved while meeting the requirement to reduce rockfall risk.

Mar 29, 2023

TSL Concepts and Practical Examples of the Non-Reactive System - Meyco TSL 865 Thin Spray-on Liners (TSLs) have been intensively investigated by mining and chemical industries within the last decade. Apart from the basic concept of spraying thin liners, expectations of the product's performance vary, eg immediate active strata support is seen as a key to control the ground permanently. For many coal mines this is an important factor to reduce maintenance in their roadways and enable permanent production from the long wall. In opposition to a passive mesh system this technology offers immediate active support to the strata. But not only coal mines are interested in TSL technology, there are potential applications in hard rock mines, during shaft sinking, pillar support and as an anti-weathering sealant. This paper will explain the advantages and disadvantages of TSL concepts; it will give examples of successfully applied TSLs with a main focus on the non-reactive and flexible system MEYCO TSL 865 by BASF. Furthermore, it will indicate the limitations and discuss briefly the bearing capacity and reasonable lab testing of such systems.

Nov 25, 2010

By C. Graham

Thin Spray-On Liners (TSLs) have been researched and in development for over two decades and yet their fully functional and widely justifiable application in mining has yet to be achieved. While the explanation for this is partly technical, it is also clear that proving and communicating the operational and economic case for why a mine should change from mesh or shotcrete liners to a TSL is not a trivial matter. Evidence must be presented and communicated effectively, that is both obvious and compelling for a mine operator. The paper describes recent work carried out and directed towards this end, with funding from CAMIRO?s Deep Mining Research Consortium and additional support from 3M Canada and ABB Canada. The essential progress that has been, or is in the process of being made, will be described in providing the necessary proof of acceptable or superior TSL performance in the following areas: polymer formulation, health and safety, geotechnical specification, robotic liner application, business case economics and yielding ground support effectiveness. Future plans are also presented to demonstrate the performance of a new 3M composite TSL/yielding bolt support system in underground trials where the substrate rock is intended to fail through a number of mining-induced mechanisms.

Aug 1, 2013

By Z Li, D Chalmers, J M. Tenney

This paper presents the findings and analysis of the investigation of effectiveness of thin spray-on liners (TSLs) as a gas management tool in underground coalmines. The project involves spraying TSL on the area surrounding gas drainage holes whereby the TSL acts as a thin membrane decreasing the permeability of the coal. This restricts air migrating through the coal seam and diluting gas from the drainage holes. There are a number of potential benefits from this technique but key points are that gas drainage holes produce gas with higher concentrations of methane. The design and execution of a field trial to investigate the effectiveness of a TSL on purity of in situ methane from gas drainage holes is presented in this report. For eight drainage holes, the results show an average increase in methane purity by 9.14 per cent and a reduction in air contamination by an average 7.93 per cent. Overall methane flow rate decreased by 27.6 L/s; however, flow rates were unreliable due to poor measuring equipment. For most holes, methane purity was not changed significantly; however, certain boreholes were responsible for most of the variation in methane purity. The boreholes showing a dramatic improvement in methane purity were likely those with intersecting cleats covered by the TSL. If the TSL was sprayed over more area, specifically in areas where the cleats are intersecting with holes, it is likely that purity of methane in the drainage holes will increase.CITATION:Tenney, J M, Chalmers, D and Li, Z, 2015. Thin spray-on liners potential in reducing dilution of in situ gas in underground coalmines, in Proceedings The Australian Mine Ventilation Conference, pp 323–328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Andriy Burbelko, Daniel Gurgul, Wojciech Kapturkiewicz, Marcin Gómy

"The mathematical model of the globular eutectic solidification in 2D was designed. The proposed model is based on the Cellular Automaton Finite Differences (CA-FD) calculation method. The model has been used for studies of the primary austenite and of globular eutectic grains growth during the ductile iron solidification in the thin wall casting. The model mentioned above takes into account, among other things, non-uniform temperature distribution in the casting wall cross-section, kinetics of the austenite and graphite grains nucleation, solute diffusion and non-equilibrium nature of the interphase boundary migration.Some aspects of stochastic nature of the solidification processes are taken into account. The results of the CA solidification modeling have been shown, that differences between cooling curves obtained in the same conditions of the casting solidification may be a result of the stochastic nature of the grain nucleation.The results of modeling were compared with the experimental microstructure. The model is well worked for thin walled ductile iron casting, for fast solidification process.IntroductionNodular graphite cast iron, also known as ductile iron (DI), has major applications in critical engineering parts due to its mechanical properties and castability. The mechanical and physical properties of this material depend on the shape and number of the graphite grains andmicrostructure of the metallic matrix.Solidification of DI was a subject of many computer modeling programs described in literature [ 1-5], in which the stationary conditions of carbon diffusion in austenite is pre-assumed. Recently, a tendency for production of thin-walled castings has been observed [ 6-8]. In this technology, the process of the fast solidification may be very far from equilibrium and steadystate conditions [9].The purpose of the present work is a two-dimension model development for simulation of the DI structure formation during the solidification in the condition of non steady-state temperature and diffusion fields in the thin-wall casting.Model of process The CA-FD is one of the known methods of the simulation ofmicrostructure formation during the solidification [ 10, 11]. In the CA microstructure modeling the outer grain shape is the result of the simulation and does not superimposed beforehand. The model development for a onephase microstructure evolution is a subject of the numerous researches [12 -23]. Model of the eutectic solidification of DI in the uniform temperature field and superimposed cooling rate is known [24]."

Jan 1, 2013