Search Documents

By T. Schmidt, J. Merza

"This study considers two lead/zinc/silver orebodies which have historically had a problem with pyrite, pyrrhotite and sphalerite contamination in the lead circuit. The problem was previously addressed with high dosages of sodium cyanide as the primary depressant. However, large amounts of cyanide led to environmental problems in the effluent, especially during winter months. The objective was to reduce cyanide consumption while maintaining or improving overall lead grade and recovery via the reduction of the undesirable sulphides.Extensive laboratory and mill testing was necessary to determine the optimal operating parameters for continuous plant application. Evaluation of data received from this testing has shown that selective addition and optimization of the dosage of Unimax SD100 to specific areas of the flotation and grinding circuits has resulted in improved Pb grade and recovery. Parameters such as pH control, regrind operation, the cyanide/Unimax ratio and sulphide mineral content may also affect the performance of the depressant. Each factor is discussed and optimal operating conditions were determined based on the testing.Results are presented for two case studies. Both indicate that Unimax SD100 improves the lead grade/recovery curve by increasing iron and zinc rejection while reducing cyanide consumption and the resulting environmental concerns. 1. Hart"

Jan 1, 1992

By Cesar A. Urbano Jr., Gretchen T. Lapidus

A series of experiments examined silver extraction from a high-grade sulfide concentrate employing thiourea solution. Thiourea was initially oxidized with hydrogen peroxide (H2O2) to form formamidine disulfide (FADS) and used to extract silver from the as-received concentrate and after various pretreatments. Very low recoveries (~30%) were obtained with the as-received concentrate due to competitive cementation reactions by metallic iron and easily oxidizable copper phases. Over 80% Ag recovery was obtained when the concentrate was pretreated to remove this iron and copper. The results suggest that an oxidative acid pretreatment of this concentrates significantly improves silver recovery upon leaching with thiourea.

Jan 1, 2014

By I. R. Taylor

Union Carbide has recently developed two open- pit vanadium mines in the Wilson Srpings area of central Arkansas about five miles southeast of Hot Springs. The ores from these mines, together with those from a larger vanadium deposit at nearby Magnet Cove, are processed at a new 1600- tpd plant built by the company in the immediate vicinity (Fig. 1). The Wilson Springs vanadium deposits are associated with the Potash Sulfur Springs intrusive, a circular igneous complex which is exposed over an area that is somewhat less than a mile in diameter.1 The complex has a crude ring structure similar to that of the larger Magnet Cove instrusive six miles to the east.2

Jan 4, 1969

By K. W. Lentz

The Maybell Mill of, Trace Elements Corporation, Unit of Union Carbide Corporation is located approximately five miles northeast of Maybell, Colorado, and twenty-five miles northwest of Craig. It is located in the midst of the uranium ore deposits whose presence, made it possible. In November 1953 Russel Cutter, Chief Geologist for the original Trace Elements Corporation, picked up high readings on a scintillometer while flying over this area. Later, with George Morehouse, Chief Engineer for the original. Trace Elements Corporation, he started a search for surface indications. In this search, they found an out crop which can be regarded as the discovery lode on this property. The actual locating of claims and acquiring free lands and state lands was begun in March 1954. During 1955 enough drilling was done to indicate that a sufficient tonnage of ore existed to make possible a mill. These ore deposits are located in the Browns Park formation which is an unconsolidated sandstone with a few hard lime ribs running through it. The geologists tell us that this region was once a vast basin which became filled with wind blown sand and volcanic tuff, Later on, ground waters brought uranium into the basin which precipitated out in the sand. During the late summer and fall of 1955, a small pilot plant was operated under the supervision of John L. Chapman testing these Browns Park ores. During the operation of the pilot plant, three small open pits were developed and the ore from these pits shipped to Union Carbide Nuclear Company, Division of Union Carbide Corporation, at Rifle. To date all ore is being mined from open ptis. In the fall of 1956 the original Trace Elements group signed a contract with: the AEC for a mill at Maybell and on November 5, 1956, Union Carbide acquired the Trace Elements Corporation properties and contract. During the next two months, intensive research was carried out on the Browns Park ores by our research lab at Rifle. They also checked some of the metallurgical results which had been obtained through the operation of the pilot plant by the original Trace Elements group. During this period, a report on Trace Elements Corporation ores was also prepared by the Colorado School of Mines Research Foundation. This report contained data on representative samples of the ore tested for the original Trace Elements group. From this research and study a flow sheet was decided upon.

Jan 1, 1959

By Neil A. Brown

The trona deposits near Green River, in southwestern Wyoming are world class in size and quality. They contain more than 25 times the reserves of the next largest trona deposit at Lake Magadi in Kenya. Based on present rates of production, the Green River reserve should last for more than 500 years. Since their discovery in 1938, the Union Pacific Corp. has been instrumental in the promotion, development and production of soda ash in Wyoming. Union Pacific spent several years drilling the deposits and trying to promote them to chemical companies. In 1947, Westvaco and Union Pacific entered into what became the first trona lease agreement. Today, the Green River Basin leads the world in soda ash production, accounting for about 25% of the world's supply. Green River producers process more than 14.5 Mt/a (16 million stpy) of trona to produce more than 8 Mt/a (9 million stpy) of soda ash. The future for Green River soda ash looks good, with more of the world looking towards the cheaper and higher quality source of soda ash coming from the natural deposits. Production from the Green River deposits should continue to grow as trade barriers and tariffs begin to fall in Europe and energy and environmental costs force the synthetic producers to exit the market.

Jan 1, 1995

By Giles D, Wegmann D

The Mt Todd Gold Project is located 42 km northwest of the township of Katherine within the Northern Territory of Australia. It is situated in the southeastern portion of the Pine Creek Geosyncline. The Batman gold deposit, the largest of several deposits at Mt Todd, hosts an identified mineral resource of 92.9 million tonnes (Mt) grading 1.4 grams/tonne (g/t) as at 31 December 1993. Host rocks at Batman are assigned to the Early Proterozoic Burrell Creek Formation, comprising greywacke and siltstone interbedded with shale. Gold mineralisation is associated with a very broad zone of sheeted and stockwork quartz-sulphide veins that occupy a corridor of intense brittle fracture and faulting. A conceptual model of formation involves the dilation of joints and micro-faults within overlying sediments during sinistral movement along a basement shear zone. Synchronous granite intrusion generated convective circulation of crustal fluids through the sedimentary pile resulting in the formation of auriferous quartz veins within favourable structures. The Batman zone of mineralisation is not directly related to fold structures which typify several other major gold deposits within the Pine Creek Geosyncline.

Jan 1, 1994

By Gerald Verbeek, Erick Baziw

Dynamic soil analysis (DSA) in geotechnical practice is intimately related to the capability of measuring the necessary soil properties of shear modulus and absorption. In DSA the methods of analysis are based upon the stress-deformation response of soils due to imposed shear strains. Typically the soil profile is numerically modeled as linear visco-elastic system. This technique is referred to as the Equivalent Linear (EL) method, and it requires the specification of the input parameters of low-strain (<10-5) shear modulus, modulus reduction, and the equivalent viscous damping ratio, which is directly related to the soil absorption value. Downhole seismic testing (DST) has proven to be a very accurate tool for estimating low strain shear modulus values as long as source wave raypaths are taken into account, especially for near-surface investigations. DST has also been utilized to estimate low-strain interval absorption values. In these cases standard frequency domain absorption estimation algorithms (such as the spectral ratio technique) are utilized where it is assumed that the source waves are traveling along the same travel path, which is obviously not the case for near surface DST investigations. This paper outlines a unique DST absorption estimation methodology, which is carried out in the time domain and takes into account source wave travel paths. 1. INTRODUCTION There is considerable interest in methods of geotechnical in-situ engineering that provide accurate estimates of the shear wave velocity and the associated absorption values in the ground, since these parameters form the core of mathematical theorems to describe the elasticity/plasticity of soils and they are used to predict the soil response (settlement, liquefaction or failure) to imposed loads (whether from foundations, heavy equipment, earthquakes or explosions).

Jan 1, 2019

By John T. MacWaters, George H. Milly

INTRODUCTION This paper describes operational procedures and instrumentation which were developed to implement a patented method of detecting and locating uranium ore bodies. All equipment was designed for accurate and reliable use under difficult field conditions. Data resulting from these developments, some of which are incorporated in a companion paper for this conference*, have contributed to our understanding, of the nature and significance of naturally-occurring radon exposures. Further applications of these techniques may prove useful in studying anthropogenic radon in evaluating the significance of variability in radon flux, or in taking proper account of the contribution of natural radon to ambient radon concentrations, particularly in mineralized regions. OPERATIONAL PROCEDURES The uranium search technique employed by GEOMET begins with a [reconnaissance mode], which utilizes a series of ambient air filter samples taken from a moving or standing vehicle to detect anamalous concentrations of radon. These samples are normally taken at night under stable (temperature inversion) or neutral atmospheric conditions, to avoid the rapid dispersion of the radon clouds typical of daytime turbulent conditions. Radon daughters formed by the decay of radon quickly attach to ambient aerosol particles and are captured on the surface of a membrane filter during a five-minute sampling period. The filter is placed in a portable alpha scintillation counter, and a five-minute count is started at a preset time after the completion of the sampling period. This count is followed immediately by a second five-minute count to enable determination of the cloud age, based on consideration of the relative half-lives of the initial radon daughters. With the use of tables computed from the mathematics of the uranium decay process, and with the measured radon background accounted for, the first and second counts are used to estimate the time which has elapsed since the pure radon initially emanated from the earth&apos;s surface. This cloud age, combined with wind speed and direction measurements made at the beginning and end of each sample, as well as with an understanding of the effects of local terrain features on wind trajectory, provides an estimate of the Probable location of the source. In practice the reconnaissance mode involves one vehicle with a single operator to take the five-minute samples, moving or standing, along any available roads or trails in the area to be covered. Under the usual nighttime stable conditions the cool air flows downslope and downvalley, and the operator will pay special attention to locations along the axes and confluences of the natural downflow patterns. These facilitate sampling of large air drainage areas. Successful detection of sources of radon based on high concentrations of radon daughters, and substantiated by evidence of "fresh" clouds, are frequently made on the basis of a relatively few samples taken judiciously by an experienced operator during a reconnaissance. At this point he has a choice: he can continue to cover the designated reconnaissance area, leaving the localization of any anomalous radon detections to await the ranking of detections by priority, or he can continue with localization of the detected source, either alone or by radioing for another vehicle to assist in triangulation operations. Localization of a source involves skillful and experienced use of the continuously collected data on concentration, age, and wind speed and direction, together with knowledge of the terrain from observation and contour maps, and exploitation of the available roads. Since age ratios are dependent solely on proximity of the source and wind speed, decreasing [cloud ages] based on statistically significant increasing age ratios represent the most useful. information in localization. The [magnitude of the concentration] of radon daughter products is also useful; however, it may vary widely for a variety of reasons during sampling for a localization, thus making this a secondary parameter for localization. Large values of concentration are of course useful; typical results for successful detection of a strong anomaly would yield alpha counts ranging from 10 to 25 times background values. These counts are convertible to ambient radon concentrations by appropriate consideration of the decay process. Successful localizations of radon sources using this procedure with ambient atmospheric measurements normally will narrow a source location to within an area ranging in size from less than a quarter of a square mile to at most a square mile, and frequently give information on the probable shape of the source (in plan view) on the earth&apos;s surface. Judicious use of this procedure could undoubtedly provide finer localization, but the coarser results just described are adequate for this Phase of GEOMET&apos;s uranium exploration procedures.

Jan 1, 1981

By David Jurich, Ed Perko, Jacob Prezkuta

Numerous Colorado mountain tunnels that date to the late 1800s convey water to the farming and urban communities of the eastern Front Range. Repairs to these remote facilities, often located in public lands at altitudes of 11,000 feet or more, require detailed planning, close coordination with multiple agencies, and creative execution. Issues and solutions discussed include designing repairs in undocumented ground and support conditions, logistical challenges, work in a short summer construction window, stabilization of historically signicant structures, and proect delivery strategies. xamples that illustrate early contractor involvement, exibility in design, and construction solutions are presented.

Jun 23, 2024

By Bjarne Ekberg

"The most economical way of dewatering mineral concentrates is to reduce the moisture content in the material mechanically using thickeners and filtration avoiding thermal drying whenever possible. In addition to this, the dewatering process should produce low moisture cake, high quality liquid, consume little energy. As a part of the dewatering process The CERAMEC® capillary filter has been proven to meet these requirements in over 150 installations. The filtration is done by using ceramic filter plates with small pore size. The capillary action in the filter medium secures gas free filtration at good vacuum, and due to the small pore size, filtrate is crystal clean and particle free. The energy consumption is minimal. This paper will discuss results from filters installed at Pyhäsalmi Mine Oy in Finland where the technology was has been used since the late eighties. Results from more recent installations like Los Pelambres in Chile and LKAB in Sweden will also be discussed.INTRODUCTIONThe idea of using capillary action to make dewatering more efficient was invented two decades ago. Ten years later whole filter plants utilizing the new method were delivered to mine concentrators for dewatering of mineral concentrates. Further development of ceramic membrane plates made it possible to meet the requirements in iron ore dewatering. In addition to low cake moisture, high capacity and low energy consumption, there are a lot of environmental advantages in using capillary filtration. One of them is clear filtrate.CAPILLARY FILTRATIONA micro-porous filter material behaves like a large number of narrow capillaries forming a network. When a pressure difference ?P is applied over the wetted, hydrophilic pore with the radius r, the force striving to push the water out of the pore will be ?Ppr2. The force striving to hold the water in the pore will be the vector force 2pr? cosa of the surface tension ? and the cosine contact angle a. Equalling those forces and solving the equation for ?P we get"

Jan 1, 2003

By Todd Kilduff, James Grillo, Shrey Arora

In efforts to improve ingress/egress from the existing subway platforms in PATH’s Exchange Place Station, a new 18-foot horseshoe cross-passage tunnel was constructed by Walsh Construction who retained Kilduff Underground Engineering for design of the initial support system and to install and maintain geotechnical instrumentation. The project presented some unique challenges as a result of the proximity to pedestrians on the platform. PATH service remained uninterrupted, limiting the Contractor to mechanical means of excavation to advance the heading. The logistics proved very challenging for the approximate 100-foot-long tunnel excavated in soft Manhattan Schist. This paper will present the design and construction challenges for the project.

Dec 1, 2022

By Pier Francesco Paglini, Gian Luca Menchini, Pier Francesco Boschi

"PROJECTThe “Caltanissetta” Tunnel is part of the ANAS S.p.A (National Autonomous Roads Corporation) $ 1.3 Billion Highway 640 Caltanissetta-Agrigento (Sicily, Italy) Rehabilitation Project, consisting in upgrading of 62 km (40 miles) of highway. The Italian multinational construction company Cooperativa Muratori & Cementisti di Ravenna, is the General Contractor for the design and build contract. The highway S.S. 640 starts from Porto Empedocle, to the intersection with the Motorway A 19 Catania-Palermo.The entire project, double carriageway designed for speed 70-120 km/h and maximum longitudinal slope of 4.2%, is divided into two sections. First Section: just finished and opened to traffic. Second Section: mainly involving the province of Caltanissetta, length about 28 km (18 miles), works started in 2013. This second section includes the most challenging work of all the project, the “Caltanissetta” tunnel consisting of two separate tubes, each with 3.9 km length and inside diameter of 13.50 m, in order to host 2 traffic lines and an emergency line. HORIZONTAL AND VERTICAL ALIGNMENT - GEOLOGY AND HYDROGEOLOGYThe plan alignment of “Caltanissetta” tunnel is formed by two tubes which are located at a minimum mutual distance of 22 m to a maximum of 63 m, with n. 9 pedestrian and n. 4 road cross passages; ventilation shafts are not provided. Overburden over portals area is about 5 m till a maximum of 120 m. Tunnel sections have variable longitudinal slope from 2.6% to 0.5%, transversal slope of about 3.5%. Right tube length is 3,992 m, left tube length is 3,877 m."

Jan 1, 2016

By C Donnelly

Redpath Australia is using a unique mining method for the Australian underground coal industry at Kestrel Mine Extension in the Bowen Basin, Central Queensland.The project involves completing two separate drifts from the surface for access to the German Creek Coal Seam located approximately 230 m below the existing surface. The scope of work is primarily the construction of two drifts; the first is 1577 m at 1 in 6 gradient and the second 1874 m at 1 in 8 gradient. Each drift has been developed by a Mitsui S200 roadheader with modifications to allow for a continuous tunnelling/mining cycle operation. A shotcrete boom has been fitted to the left hand side of the machine with the operators console located at ground level. Another operators console is elevated on the right hand side of the machine to allow operation of the rotary drill boom which is mounted on a slide rail to allow flexibility of positioning depending on the stage of the cycle. In support of the roadheader activities, an integrated conveyor system mounted on a sliding floor arrangement is able to be advanced as the mining face progresses. This sliding floor consists of four 1.5 m × 6 m sections that utilise hydraulic rams to ‘walk’ inbye, allowing room for installation of precast concrete floor panels for final floor completion. This method borrows from the tunnelling and construction industries to eliminate place-change delays in the mining cycle by enabling complete ground support installation without retreat of the primary development machine from the face. The aim is to reduce the project duration with the completion of final floor and services to within 30 m of the operating face as it advances.

Mar 21, 2011

By S. A. G. Poppen, J. Konopka

"Petro-Canada&apos;s project investigative and experimental underground work in the Galt coal seam at Kipp, Alberta included the construction of an emergency egress and ventilation raise from surface.The Galt coal seam is 206 m below the surface and covered by 8 m of shale, sandstone and clay beds of the Oldman Formation, 128 m of shale, bentonite beds and sandstone of the Bearpaw Formation, and 70 m of glacial till and basal gravel. Free water was encountered from sand lenses in the glacial till and the basal gravel.Excavation for the ventilation raise was a nominal 2 m diameter and it was lined with a welded, continuous, steel liner of 1.2 m 1.D.Excavation in the glacial till was carried out with a surface bucket drill rig combined with hand mining. Ground support in the glacial till consisted of liner plates and backfill grout. The Bearpaw and Oldman formations were excavated by employing standard raise boring techniques. The individual liner sections of the continuous steel liner were assembled on surface and the entire liner column was lowered into the raise by employing hydraulic lift climbers. The liner column was back-filled with concrete.IntroductionThe Lethbridge Coal Field comprises an area of approximately 1 165 square km in the vicinity of Lethbridge in southern Alberta. Pacific Petroleums Ltd. proposed in a Preliminary Disclosure in January 1979 ""to open an experimental mine prior to development of a producing underground mine with an initial rate of 540,000 tonnes per year"". A 2 900-hectare group of leases in the Kipp-Coalhurst area was selected as the primary target for the Kipp experimental mine. The scope of work for the experimental mine included the construction of an access shaft with production capabilities, the construction of a ventilation and emergency exit raise, drive-ages in coal to yield a bulk sample, gathering of geotechnical information and the testing of experimental mining methods."

Jan 1, 1983

By B Veera Reddy

For thick seam extraction, the Blasting Gallery (BG) method is ideal for obtaining the maximum percentage of extraction at fast rates. The continued use of this mining method is threatened by strata control and spontaneous heating problems. The strata control problems are managed, to some extent, by supporting the roof with cable bolting and roof bolts of 2.5 m length and with regular induced blasting. However, a number of BG panels were sealed off prematurely due to spontaneous heating problems, losing 1.12 million tonne of coal. The use of compressed CO2 for controlling mine fires is not uncommon in the coal mining industry, but its use is something new for controlling active spontaneous heating in a BG working panel goaf. This method was attempted at the BG I/8 panel of the Godavarikhani (GDK) 8 Incline, Singareni Collieries Company Limited (SCCL). The spontaneous heating was effectively controlled and the remaining coal in the panel was completely extracted by continuous flushing of carbon dioxide (CO2) into the goaf for 40 days. One thousand and twenty four CO2 cylinders, each of 45 kg at 80 bar pressure were flushed into the goaf at the rate of 25 to 30 cylinders (350 m3 of CO2) per day. A quantity of 35 510 tonne of coal was extracted during the period from 30 July 2002 to 7 September 2002. The main objective of this paper is to present the complete process of controlling the spontaneous heating by CO2 flushing and to report on the study of the behaviour of gases and their analysis. The unique experience of controlling the active spontaneous heating in the working Blasting Gallery I/8 panel goaf at GDK 8 Incline with CO2 flushing (till the completion of the panel) will go a long way in establishing a working procedure for handling fire/spontaneous heating problems in BG panels.

Jan 1, 2005

By A. Esterhuizen

Since 2005 Two Rivers Platinum Mine has set out on an initiative to actively monitor and control ground conditions on a daily basis, by making use of borehole cameras and pro-actively amending the support and mining strategies based on day-to-day observations of the hangingwall conditions. Today the borehole camera observations form part of the Rock Engineering Department?s daily function, and the size and frequency of falls of ground and ensuing accident rates have been drastically reduced since implementation of the system. The Two Rivers Platinum fall-of-ground management system aims to support 100% of the possible fallout thickness, based on ongoing data gathering and interpretation, thereby ensuring safety and limiting support cost.

Jan 1, 2014

By R. J. Fruehan

Slags have many useful functions in iron and steel making. In particular, slags are used to remove impurities such as sulphur, phosphorus and inclusions from the metal, and a large amount of research has been done in this area. Slags also insulate the metal thermally and form reactions with the atmosphere such as reoxidation and nitrogen pick-up. However, slags serve other more unique functions, several of which are reviewed in this paper. The role of slags in new iron smelting processes with regards to reduction of ore and gaseous desulphurization are discussed. In iron smelting processes, much of the reduction occurs by the reaction of carbon in the char and the metal suspended in the slag with iron oxide dissolved in slags. The slags also react with the gas resulting in sulphur removal from the process. The mechanisms of these reactions and pilot plant data for these processes are given in this paper. Slag formation within ferrous burden materials affects the cohesive zone and the performance of the blast furnace. Recent theoretical and experimental findings on this topic are presented. In the electric arc furnace, foamed slags are used to allow for higher power operation and productivity. Of particular interest, foaming in stainless steel production is more difficult than for normal steels. The foam index, or the ability of the slag to foam, for stainless steelmaking is similar to that for carbon steelmaking slags. The poor foaming is due to the lack of gas generation for the foam. Methods to increase foaming in stainless steelmaking are discussed.

Jan 1, 2004

By Takahiro Furuzono

Saganoseki Smelter and Refinery of Pan Pacific Copper Co., Ltd. started treating copper anode slimes using a unique hydrometallurgical process in chloride media in 1997. The process comprises the following stages, decopperizing, wet chlorination, solvent extraction for gold, silver chloride reduction, and separate reduction stages that treat the gold extraction raffinate with sulfur dioxide gas. Precious metals and rare metals in the copper anode slimes are dissolved in an aqueous solution of hydrochloric acid by oxidative leaching, which is termed wet chlorination. Gold is efficiently extracted from the chlorination liquor by dibutyl carbitol in the solvent extraction stage. Gold is reduced by oxalic acid from goldloaded dibutyl carbitol and recovered as gold powder. The gold powder is cast directly into granules or ingots of more than 99.99% purity without electrorefining. Selenium is recovered as a selenium residue by reduction with sulfur dioxide gas and refined through vacuum distillation. The plant was designed to process 132 tonnes of copper anode slimes per month and has a current capacity of 206 tonnes per month due to several enhancements. Compared with the conventional process, the hydrometallurgical process described here provides some advantages, in particular, a higher product quality, shorter gold-retention time, and reduction in environmental load.

By W. W. Coffeen, K. E. Doud

A singular mineral extraction and processing operation is conducted by Metal & Thermit Corp. in Hanover County, Va. The mine presently produces aplite rock, rutile and ilmenite. The deposit lies in the piedmont plain about 25 miles northwest of Richmond. It first drew attention as a result of discovery of float rutile on the surface about 1910. About seven years prior to this, Metal & Thermit through a subsidiary. American Rutile Co., had begun producing rutile&apos;and ilmenite from a deposit in Nebon County, near Piney River, where aplite rock and ilmenite are mined today. Because of the interest in titanium minerals and the similarity of the new deposit to the Nelson County deposit, Metal & Thermit became interested and eventually acquired the Hanover County deposit.

Jan 10, 1962

By K. E. Doud

An unusually pure grade of rutile and several grades of aplite rock are produced in a unique mining and mineral dressing operation in Hanover County, Virginia. The ore body is an aplite rock of gnessic structure, having a sari ace exposure extending over several hundred acres, heavily leathered and containing rutile, ilmenite, and other titanium and iron minerals. The physical nature and mineral composition of the ore body has permitted the use of a relatively economical and unusual processing circuit. The flowsheet was designed to take full advantage of the remarkable liberation of the minerals at relatively coarse rinds. It permits flexibility in changing the product mix, and maintains high levels of purity in both rutile and aplite rack. The mineral processing is discussed in some detail below.

Jan 1, 1962