Search Documents

By I. Gombköto

Mining and mineral processing operations are usually generating huge amount of tailings. These tailings often gives lots of maintenance work in order to protect environmental resources from heavy metals slowly leaching out of tailing are due to Acid Rock Drainage (ARD) process. Handling leakage could be active or passive such as using of Permeable Reactive Barriers (PRB). PRB?s are used worldwide treating underground contaminations, using different type of matrix materials. All generally used matrix material has its advantages and disadvantages such as selectivity, sensitivity of precipitation generation or not satisfying hydraulic conductivity. Nowadays cheap and effective matrix material which is ignorant to pore plugging caused by precipitation within the PRB could be one solution to the demands of the industry. The authors have been carried out an investigation at University of Miskolc on lignite as high humid acid containing material for determining the ability of heavy metal adsorption and pore plugging resistance. Moreover, using hydraulic and chemical simulation methods, complete PRB dimensioning protocol based on new lignite matrix had been introduced. Within the frame of this paper the results are going to be discussed.

Sep 1, 2012

By D Caley

During the response to the Moura No 4 disaster, use was made of the New South Wales Mines Rescue Service’s ‘Mineshield’ inertisation equipment. The equipment had to be transported from Newcastle, approximately 1400 kms, and the liquid nitrogen a similar distance. The time taken, and therefore availability of the liquid nitrogen, became a significant problem. Operational issues were also experienced during use. Typically the liquid nitrogen is converted to a gas (vaporised) before being injected into the mine. However, as the propane gas tanker used for the vapourising unit was delayed, an attempt was made to inject the liquid nitrogen directly down uncased boreholes. This proved unsuccessful.Following the Moura No 4 disaster and the Moura No 2 disaster, recommendations were made relating to having inertisation capacity for the Queensland coal mining industry. Today the Queensland industry has multiple options available for inertisation, including the high-volume GAG and smaller volume units such as boilers and membrane separation units. Although it ultimately aided re-entry into Moura No 4, most likely due to the issues associated with supply to Central Queensland, liquid nitrogen has not found favour within the Queensland industry as an inertisation tool.Coregas has commissioned an air separation plant in Mackay, improving the availability of liquid nitrogen to Central Queensland. Based on the availability of this nitrogen, recent sealing operations at Kestrel have trialled using liquid nitrogen and associated vapourising units. This paper details the practical application and findings of using liquid nitrogen during routine longwall panel sealing.CITATION:Caley, D, 2017. Using liquid nitrogen for the inertisation of goafs, in Proceedings Australian Mine Vent Conference 2017, pp 35–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Mei Long, Tawum Juvert Mbah, Jianhua Zhang, Haiwang Ye

There have been many improvements and advancements in the application of neural networks in the mining industry. In this study, two advanced deep learning neural networks called recurrent neural network (RNN) and autoregressive integrated moving average (ARIMA) were implemented in the simulation and prediction of limestone price variation. The RNN uses long shortterm memory layers (LSTM), dropout regularization, activation functions, mean square error (MSE), and the Adam optimizer to simulate the predictions. The LSTM stores previous data over time and uses it in simulating future prices based on defined parameters and algorithms. The ARIMA model is a statistical method that captures different time series based on the level, trend, and seasonality of the data. The auto ARIMA function searches for the best parameters that fit the model. Different layers and parameters are added to the model to simulate the price prediction. The performance of both network models is remarkable in terms of trend variability and factors affecting limestone price. The ARIMA model has an accuracy of 95.7% while RNN has an accuracy of 91.8%. This shows that the ARIMA model outperforms the RNN model. In addition, the time required to train the ARIMA is than that of the RNN. Predicting limestone prices may help both investors and industries in making economical and technical decisions, for example, when to invest, buy, sell, increase, and decrease production.

Jan 6, 2021

By Braam Blom

PK2 Ventilation shaft is part of Paardekraal No 2 twin shaft system that is being developed to replace depleting Merensky reef production at Paardekraal shaft complex. The sinking team at this shaft faced considerable challenge of improving the total sinking cycle in order to be able to deliver the fully equipped shaft on time and on schedule. The cladding support cycle was identified as the tedious and time consuming activity in the overall shaft sinking operation. Reduction in the time required for handling and setting up the support installation equipment, and the time required for subsequent installation of the necessary support has a direct impact on the overall cycle time, and consequently the overall productivity and efficiency of the sinking operation. This reduction in support cycle was achieved by making use of machine carousel. The objective of this paper is to describe the support methodology that was used during the ventilation shaft sinking and the use of the machine carousel to reduce the cladding support cycle. The machine carousel replaces the traditional use of machine kibble in conventional vertical shaft sinking and has been designed specifically for installation of sidewall support at the shaft bottom during the sinking process.

Jan 1, 2009

By Braam Blom

PK2 Ventilation shaft is part of Paardekraal No 2 twin shaft system that is being developed to replace depleting Merensky reef production at Paardekraal shaft complex. The sinking team at this shaft faced considerable challenge of improving the total sinking cycle in order to be able to deliver the fully equipped shaft on time and on schedule. The cladding support cycle was identified as the tedious and time consuming activity in the overall shaft sinking operation. Reduction in the time required for handling and setting up the support installation equipment, and the time required for subsequent installation of the necessary support has a direct impact on the overall cycle time, and consequently the overall productivity and efficiency of the sinking operation. This reduction in support cycle was achieved by making use of machine carousel. The objective of this paper is to describe the support methodology that was used during the ventilation shaft sinking and the use of the machine carousel to reduce the cladding support cycle. The machine carousel replaces the traditional use of machine kibble in conventional vertical shaft sinking and has been designed specifically for installation of sidewall support at the shaft bottom during the sinking process.

Jan 1, 2009

By Ravi Sahu, Brad Gyngell, Oktai Radzhabov

Design machine learning approach to simulate the process of muckpile throw distribution before blasting.

Feb 1, 2020

By D. R. Hanson, H. Lawson

In this study, NIOSH researchers conducted a machine learning analysis to examine whether a model could be constructed to assess the probability of dynamic failure occurrence based on geochemical and petrographic data. Random forest, cluster analysis and dimension reduction were all applied. The objective of dimensionality reduction was to explore patterns and groupings in the data and search for relations between compositional parameters. Cluster analyses were performed to determine if an algorithm could find clusters with given class memberships and to what extent misclassifications of dynamic failure status occurred. A random forest analysis performed on data from the Pennsylvania Coal Sample Databank cross-referenced with accident data from the Mine Safety and Health Administration (MSHA) determined that 7 parameters of the 18 examined exerted the most influence on results. Cluster analysis on data after dimensionality reduction resulted in a hierarchal clustering algorithm finding four clusters, with one relatively distinct dynamic failure cluster, and three clusters consisting mostly of control group members but with a small number of dynamic failure members.

Feb 1, 2023

By J Herd, J Rowe, M Cutbush, d F. Aziz

WearApp provides expertise for assessing the degradation of removable screening media panels on vibrating screens right in a user’s pocket. Through the WearApp application, users can simply take a picture of a panel using their mobile, enter some basic information and have the application assess the wear to provide a recommendation for whether the panel needs to be replaced. Where traditional mechanisms for assessing panel wear only measure a few points across the panel face and rely on having personnel with specialised knowledge available to perform the assessment, WearApp uses deep learning models to analyse the entire panel face and support the user to make an informed decision. The application works through analysing a panel image and using a model to automatically detect the corners of the panel. Given the known dimensions of the panel, this enables the application to calibrate the pixel size against a known reference. A second set of models then detect the apertures and measure their dimensions. With the aperture dimensions defined the application assesses the wear of the panel through referencing a stored 3D model of the aperture. Finally, the data from each aperture is collated and the wear of the entire panel face defined. Since WearApp performs measurement of the entire panel face, it also allows the user to perform a more detailed analysis of the panel’s wear profile. Where typically, the panel wear is only measured in a few locations, WearApp’s analysis enables users to visualise the panel wear across the entire panel face, identifying areas of high wear that could be leading to premature panel replacement. Additionally, because the entire panel face is measured the change in screening efficiency can be calculated accurately for the worn panel, even taking into account the impact of aperture pegging by small rocks.

Sep 1, 2024

By Terry Keough

Contents for discussion ?Current liner technology ?Innovation of magnetic products ?Development of magnetic wear liners ?Installation and change out method ?Uses and capabilities ?Internal wear liners ?Summary Vulcanized rubber ?Many of you are familiar with using vulcanized rubber to provide wear protection on mining equipment. For years, this was the standard for most mining equipment, and mines spent a lot of money fabricating and lining steel equipment.

May 1, 2010

By Anthony Iannacchione

A Major Hazard Risk Assessment (MHRA) was developed in Australia after a series of mine disasters in the 1990?s. A MHRA is used to help prevent major hazards, i.e. fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, from injuring miners. A MHRA is a structured process that identifies the characteristics of major hazards, assesses and ranks the risk they present, and evaluates engineering and administrative controls to mitigate them. These controls typically consists of a broad spectrum of prevention, monitoring, first response, and emergency response techniques and helps to move an operation from a reactive to a proactive approach towards safety. This paper documents a MHRA performed at an underground mine where strata instabilities and fire hazards may threaten the condition of its escapeways. The objective of this MHRA is to 1) identify what hazards could affect the egress through the mine?s escapeways, 2) determine what unwanted events pose the greatest threat for the mine, and 3) recommend a plan to prevent or recover from the potential disruption of egress through the escapeway. The plan provides information on the key existing controls that should be monitored and audited, and makes recommendation of new potential controls to further reduce related risks. By documenting the use of MHRA to this specific ground control issue, this paper provides a framework for others to judge the merits of this approach and to help design and perform these activities.

Jan 1, 2007

By Stephen C. Tadolini, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A Major Hazard Risk Assessment (MHRA) was developed in Australia after a series of mine disasters in the 1990’s. A MHRA is used to help prevent major hazards, i.e. fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, from injuring miners. A MHRA is a structured process that identifies the characteristics of major hazards, assesses and ranks the risk they present, and evaluates engineering and administrative controls to mitigate them. These controls typically consists of a broad spectrum of prevention, monitoring, first response, and emergency response techniques and helps to move an operation from a reactive to a proactive approach towards safety. This paper documents a MHRA performed at an underground mine where strata instabilities and fire hazards may threaten the condition of its escapeways. The objective of this MHRA is to 1) identify what hazards could affect the egress through the mine’s escapeways, 2) determine what unwanted events pose the greatest threat for the mine, and 3) recommend a plan to prevent or recover from the potential disruption of egress through the escapeway. The plan provides information on the key existing controls that should be monitored and audited, and makes recommendation of new potential controls to further reduce related risks. By documenting the use of MHRA to this specific ground control issue, this paper provides a framework for others to judge the merits of this approach and to help design and perform these activities.

By M. E. Rossi

Reconciliation of production information is critical to evaluating the effectiveness of the predictive models, and to allow for optimization of mining operations. Whether mining open pit or underground, mine-to-mill reconciliations can be one of management's better tools to perform proper accounting, and a very useful evaluation and optimization tool. This paper proposes a set of criteria and objectives for a typical reconciliation program; also presents a stepwise, logic approach to performing reconciliations, and discusses the benefits and costs associated with the up-keeping of the information. It also highlights some of the potential pitfalls involved, and methods used to avoid collecting misleading information. These issues are illustrated with an example of a model-to-mine-to-mill reconciliation program being implemented at an operating mine; the program involves multiple predictive models (Long-term and Short-term block models), different open pit and underground mines, stockpiling, and at least 23 different mill streams. This paper presents the initial results of the program implemented at Minera Michilla S.A.

Jan 1, 1999

By Bo Forsman

METAFORA is a simulation model for determination and evaluation of strategies for operating loader/truck systems in mining. A specific version of METAFORA was used to evaluate the haulage system at Solider Mineral's Aitik mine in northern Sweden, one of the largest open pit mines in Europe with a production of about 11.5 Mtpy (about 34000 tpd) of copper are. A production level of 34065 tpd was estimated by simulation runs with METAFORA. Using METAFORA's dispatch rules (Fixed Dispatch, Maximize Trucks, and Maximize Loaders), the truck/shovel system in the Aitik mine was simulated for evaluating alternative dispatch control strategies. The Maximize Trucks rule gave about the same total production (ore + waste) as the Fixed Dispatch rule but a 9% higher ore production. The Maximize Loaders rule gave the lowest production. The marginal truck capacity decreases with increasing number of trucks serving the same loader due to increasing waiting times. In Aitik mine the low crusher capacity results in long dumping times. If the dumping time at the crusher could be halved, the ore production would increase by 14%. The paper indicates that the use of software like METAFORA can result in a substantial reduction of time, effort and cost in shovel/truck system design and evaluation.

Jan 1, 1992

By David R. Morrey

During the past 50 years, significant research has been performed in the ecology and physiology of plants that colonize soils containing elevated concentrations of heavy metals. Similar work has also been performed on plants that are able to survive acidic and saline environments. Efforts have focused on the ecological analysis of plant communities that occur over a range of metalliferous mining wastes. Investigations have been performed on the mechanisms that allow selected varieties of plant species to survive in normally phytotoxic environments and on the potential applications of metal-tolerant varieties of plant species. The purpose is the remediation and reclamation of mining wastes and soils that contain unusually high concentrations of so-called heavy metals. Characteristics of some mineral wastes Metalliferous mining wastes present special environmental restoration problems because of their toxicity. Potential toxicities are mostly caused by residual metals derived from weathering of low-grade ore or the waste products of mineral processing. In cases where pyrite forms a part of the mining waste, acid generation by oxidation may exacerbate the toxicity problem by promoting heavy-metal mobilization in aqueous solution.

Jan 1, 1995

By Tom Gabardi, Peter Clarke

"MillMapperTM is a new 3D laser scanning technology that has only recently been introduced into the North American mining industry. It enables mill operators to gain a much more complete understanding of the condition of their mill internals and to more accurately predict how liners will perform in the future. This paper describes the technology and techniques used to obtain data on internal mill conditions, how this data is processed into meaningful information which enables better prediction of liner life and gives examples of the reports provided by the software. Examples are given, using client sites data, on how this information is being used to reduce the costs and improve the revenue from SAG and ball mills.INTRODUCTION Scanalyse Pty Ltd developed the MillMapperTM technology in Australia over a number of years and has recently introduced it into North America with a significant take-up in Canada. The technology was commercially released in Australia in late 2006 and there has been significant technical development in the features provided since that time. MillMapperTM has been accepted as a useful technology in the Australasian region and more recently has been introduced to sites in Chile, Peru, Brazil, USA, Canada, Laos and South Africa. Over 100 different mills have been scanned and the technology has been thoroughly tested and validated. It has become an integral tool in condition monitoring and improvement programs for SAG and Ball mills across many sites and is now providing significant and measurable benefits to the mining industry. Some of these benefits will be described in this paper using actual examples."

Jan 1, 2012

By R. H. Grau, R. Krog

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of large-opening mines. The research has demonstrated that the ventilation of large-opening mines improves significantly by including ventilation requirements in the mine planning process and implementing somepractical techniques during mining. Planning the location of long pillars to reduce the number of crosscuts between intake airways and return airways, positioning auxiliary fans in their proper locations, and establishing ventilation stoppings with minimal leakage all significantly improve the ventilation of large-opening mines. Mine operators that adopt these techniques in the mine ventilation plan will reduce mineworkers’ exposure to airborne contaminants.

By R. H. Grau

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of large-opening mines. The research has demonstrated that the ventilation of large-opening mines improves significantly by including ventilation requirements in the mine planning process and implementing some practical techniques during mining. Planning the location of long pillars to reduce the number of crosscuts between intake airways and return airways, positioning auxiliary fans in their proper locations, and establishing ventilation stoppings with minimal leakage all significantly improve the ventilation of large-opening mines. Mine operators that adopt these techniques in the mine ventilation plan will reduce mineworkers? exposure to airborne contaminants.

Jan 1, 2008

By R. L. Taylor, S. D. Abbott

"INTRODUCTION Mines are filled with a mixture of gases, some of which are toxic, flammable, explosive. Others can be early reporters of potential problems. It has previously been shown that analysis by gas chromatograph can the most accurate conventional analytical tool for common mine gas mixtures when used correctly. There are some other detection methods (e.g hand held sensors), but they do not detect many situations which are immediately dangerous to life or health (IDLH). Examples include explosive hydrogen mixtures, toxic carbon dioxide levels, and some explosive mixtures of methane with oxygen. (Reference our previous paper). There are several reasons for mines to consider onsite GC analysis. (1) Timeliness of results. Samples can be taken and analyzed immediately. Samples do not have to be shipped to a lab and wait for results. (2) Ability to run greater number of samples a lower for the same cost. This allows mine to increase the number of samples taken to be more informed about the gases/conditions of the mine without the worry of financial constraints. (3) Fewer sample media needed, and there is no wear and tear or cost from shipping them offsite. When samples are shipped offsite, those sample media cannot be used to take until the lab returns them when the analysis is done onsite, the sample media can be used again almost immediately. However there are several challenges associated with using GC to analyze mine gas samples onsite. To date there has been a clash of the requirements for a successful analysis, the capabilities of the technology, and the practicalities of implementation. The purpose of this paper is to discuss some of the difficulties in getting accurate reliable data and doing so in an economic way. This whole measurement activity is a cost center for a mine, so there are economic concerns for the mine to address. These concerns are mainly staffing costs, capital costs, maintenance, and consumables costs. A properly staffed and equipped analysis lab, including burdened overhead, costs about $500K per year. At a sampling rate of 10 per day, this is about $140 per measurement for a proper onsite lab."

Jan 1, 2016

Using Mineral Maps to Rank Potential Processing Behaviour

Sep 13, 2010

By I Taylor, M Nugus, C Gordon

Resource estimation and selective mining of structurally complex, high nugget orebodies presents a major challenge to the Mine Geologist. At the Golden Pig BIF-hosted gold deposit in Western Australia, an estimation method has been developed that replaces an assay-based resource estimate with one based on mineralisation intensity. Subjective coding of the mineralisation intensity has a more robust connection to local grade than drillhole assays. Indicator variograms of the five mineralisation codes are well structured with anisotropy directions similar to observed structural controls. The proportion of each mineralisation code is estimated and a weighted average of the average grade of each code calculated for a block. Initial validation has shown that the model is a good predictor of the mineralisation intensity, and the application of appropriate local average grade for each mineralisation code gives a reliable block grade estimate.

Jan 1, 2003