Search Documents

By A. K. Debnath

Coal is the mainstay of Indian energy supplies. The many-fold increase in demand for coal puts a huge pressure on augmenting production, primarily from opencast mines. The increase in production necessitates heavy blasting in overburden and coal benches of opencast mines, which poses numerous challenges in carrying out blasting operations techno-economically. Presently, the consumption of industrial explosives and accessories in Coal India Limited (CIL) has touched a whopping figure of $350 million USD per annum and CIL will be spending approximately $1 billion USD between 2012?2013 to 2014?2015 for procuring explosives and accessories. This paper discusses some of key challenges faced in various mines of CIL during blasting, where blast instrumentation at the mine level will prove to a harbinger for practicing blasting engineers. Presently, the problem of scattering in surface detonators and down-the-hole detonators affects the blast performance significantly by increased blast induced ground vibration and reduced fragmentation. The paper discusses a case study carried out at Umrer opencast project of CIL to investigate the effect of scattering by using blast simulation techniques (i.e., JKSimblast) and observing the actual blast results with the help of a high-speed camera and multi-channel high frequency data acquisition systems. The fragmentation assessment was carried out by adopting Digital Image Analysis techniques and using the granularity software viz. Wipfrag. The blast instrumentation in the case study mine resulted in improvement in fragmentation of 12.76% and a direct savings in explosives cost of 28%. Geophysical techniques such as the seismic survey method have been used at Umrer Project, CIL to characterize the rock mass using the Multi Channel Analysis of Surface Waves system for selecting the explosives technoeconomically. The minimum deck thickness for mines of CIL using drill cuttings as decking materials should be 10 D, where D is the drill diameter. The estimation of blast performance on the basis of prescribed Powder Factor (i.e., kg of explosives per m3 of rock) is technically unscientific as the criterion of a good blast depends on many factors (i.e., good heave, loose muck, muck profile angle, ease of digging, uniform fragmentation). The present paper proposes a new methodology for techno-economic evaluation of blast performance. The new methodology involves four significant factors viz. specific energy consumed by the loading equipment, charge factor, productive yield and diggability index for assessing blast performance. The use of user-friendly, accurate, reliable, rugged and handy instruments in blasting will significantly improve mine productivity, equipment efficiency and economics. The improvement in blast performance, even by 1%, will provide a significant savings of $3.5 million USD per annum to CIL. It may be concluded with high degree of confidence that blast instrumentation at the mine level will influence the mine productivity and economics.

Aug 1, 2013

By Siddall B

A brief review of the capabilities and practical limitations of blast simulation packages has been carried out. It is concluded that the simulators accurately reflect size distributions in the mid-ranges of 0.1 to 1.0 in, but are less reliable

Jan 1, 1998

By Grigor Mishev, Georgi Petrov, Benjamin Cebrian

Before designing a single blast or all the blasts on a pit level, it is critical to assess the main goal on each. To do this, a series of constraints must be taken into account: wall protection, vibration control, flyrock hazards, fragmentation required, desired displacement as well as economy, equipment efficiency. The tool to do this is the Blast Master Plan. Many mines fail to integrate on its elaboration key stakeholders such as planning, operations, geology/geotechnical and milling departments. Designs not only have to provide consistent behavior of the blasts, but have to make sense all in one with the geological and geotechnical conditions as a starting point. Once blasts are designed under an organized set of priorities, and complemented with quality controls, optimization is possible on a large scale.

Jan 1, 2016

By Shonn K. McNeill, Joshua Micah Hoffman

Security engineering is similar to other forms of engineering – the design is guided by the loads, materials, and desired function. For facility design, the load is the threat. Facilities that are designed with considerations for explosive hazards are designed with a shot, or series of shots, of a given size and distance from key locations. These facilities range from office buildings and industrial sites in developed nations to military and police stations in contingency areas. The challenge is the design shots are not often communicated to facility owners and managers. If the hazards change, whether it’s due to an increased capacity to cause damage by a threat or a decrease in capacity by a structure, not knowing the design shot means not knowing if security design needs to change. Blast modeling is an engineering tool that can be used to reverse engineer what a facility is suitable for, as well as be a tool for modifying security design for new conditions. This paper will examine military and civilian examples, including a case study of a military facility that did not know their as-built conditions and had to be rapidly closed; due to the determination their security engineering shortcomings could not be mitigated.

Jan 1, 2019

By Gordon K. Jorgeonson

Much of the modelling of blasting operations has been devoted to simulating blasts in open pit mines and quarries . This has been the most obvious application and has been reported in many papers and discussions in the past.

Jan 1, 1990

By Stephen H. Chung

The blasting performances identified above are considered to be the most practical ones for judging the effectiveness of a design combining explosives / rock / drill pattern. In a total blast design process, productivity relates closely to both fragmentation and heave / displacement of muck. In cast blasting, the more overburden displaced by explosives, the less blasted material there is left to be removed with mechanical equipment such as draglines or trucks. For wall protection and dilution control, estimates of the maximum extent of cracks / damage generated in situ due to blasting will help determine the location for drilling and loading perimeter blastholes.

Jan 1, 1994

By Stephen H. Chung

The SABREX computer blast simulation program permits the study of the effective use of explosive energies and predicts the total performance of a blast in terms of:fragment size distribution: muckpile profile; breakage at grade, column and collar with respect to the control case; crack penetration; damage envelope behind and beneath blastholes; a complete cost analysis including explosives, drilling and accessory costs

Jan 1, 1995

By D Anonby

The Fox Pit at EKATI Diamond Mine is designed with 11 m wide benches excavated using a double benching technique leaving 30 m high faces. Blasting tests were conducted to increase the percentage of benches that meet an 11 m catch width. The subdrill depth for the lower bench trim blasts and the blasthole diameter for the upper bench trim blasts were reduced to maintain the bench crests. Raising the lower trim blastholes by 0.5 m decreases the depth of broken rock below the final bench elevation, and consequently reduces damage to rock that forms the bench crest below. The use of smaller diameter (165 mm vs. 270 mm) blastholes in the A and B rows for the upper trim blast reduces the charge per delay during detonation, reduces the powder factor slightly, and reduces the energy affecting the final pit wall and crest.

Jan 1, 2007

By M Fitzgerald

Fimiston Open Pit is operated by Kalgoorlie Consolidated Gold Mines (KCGM) as a joint venture between Barrick Gold and Newmont Mining. Over 110 years of underground mining resulted in the development of nearly 3500 km of underground workings including backfilled and open stopes up to half a million tonnes in size. These voids significantly complicate blasting processes at KCGM, influencing blast movement direction and magnitude. Blast movement monitoring to improve mine reconciliations was identified as an improvement project in the business plan for the geology team in 2008. Following successful trials in 2008 to 2009, blast monitoring and translation of ore blocks were implemented as a permanent grade control program from late 2009 and is now part of the Management Operating System (MOS) of the mine. This paper presents a summary of results from the Blast Movement Monitoring (BMM®) data collected to date. Ore blocks at KCGM are translated primarily using BMM® data. This data is obtained from the BMM® system which measures the movement of a radio transmitter installed in a blast pattern from a preblast position to a post-blast position. The application of the data collected by the BMM® tends to be both mine site and blast specific. At KCGM, an average distance obtained from the BMM® data within a given shot is the primary method used for translation. In the case that BMM® data is unavailable, a theoretical movement vector established from Orica Shotplus with distances gained from the historical BMM® database is used. Data is presented in an ore loss and dilution exercise for a bench undertaken at KCGM to understand the potential effects on reconciliations. Improvements that have flowed from implementing blast monitoring include improved reconciliations when combined with other grade control improvement projects. The increase in liaison between the geology and blast personnel at KCGM has been a significant improvement gained from the implementation of the blast monitoring program. This has allowed a better understanding of blast movement and the effects on ore dilution and ore loss by the mine geology team. In addition, the discussion of blasting tie-in plans between geology and blasting personnel has been improved which leads to more favourable blasting practices that take ore movement into account.

Aug 22, 2011

By Ian R. Firth

For the majority of open pit precious metal mines in the western United States, grade control practices have evolved as a direct result of the variable geology of the ore body and the lack of a clear visual or geologic distinction between ore and waste material. These practices often include the extensive use of buffer or choke blasting, in an attempt to minimize lateral movement of the muckpile. The Mackay School of Mines is conducting ongoing research, which aims to develop a practical method of measuring the movement of discrete “targets” placed within the body of the blast. The movement experienced by these targets can then be used to interpolate the movement of the blast as a whole. Typically, the boundaries between different material types are known as digging limits or polygons and are marked using colored flagging on the muckpile. If material movement can be measured using targets placed in the blast, these digging limits can be altered to reflect the blast-induced rock movement, reducing dilution and improving value recovery.

Jan 1, 2002

By G. W. Harris, P. Mousset-Jones, J. Daemen

"To minimize ore dilution induced by blast movement in surface mines, it is necessary to quantify such movement. This will enable more accurate location of the grade boundaries beneath the surface of a blasted rock pile before excavation. A method has been developed and tested to accurately measure the direction and magnitude of subsurface blast movement. This technique uses a cesium vapour gradiometer and a real-time, differentially corrected GPS system to locate pre- and post-blast position of magnetically enhanced target objects placed within blastholes inside a bench. The procedure developed does not require the blasted rock to be disturbed, and the movement information is available within a sufficient time to allow for modification of the selective mining boundaries for each surveyed blast. It was found that the maximum depth of target detection was 18 m, with the overall accuracy being measured as ±1 m (horizontally) and ± 1.2 m (vertically). IntroductionOre dilution is a critical concern for many mining operations. In some instances, it may be the cause of considerable mineral loss. Where the mineralization is finely grained, sedimentary and disseminated in nature, and exhibits no clearly defined visual ore/waste boundary, there is a heightened possibility for ore grade dilution. In most modern open pit gold mines, it is economically desirable to minimize dilution in the production process through the practice of selective mining by defining pre-blast ore digging boundaries, called digging polygons, on the preblast bench area. The polygons’ positions are defined by sampling the production drill holes, with the resultant assay and survey data being used to estimate the areas of specified grade content within the bench. Once the ore is blasted in the bench, the pre-blast locations of these digging polygons are flagged as designated areas on the broken ore pile. The purpose is for the loader operator to be able to recognize which areas of blasted rock are to be sent to the appropriate processing facility or to the waste dump."

Jan 1, 2001

By M E. Watson

Minimising dilution and ore loss is an important part of ensuring profitability of a gold mining operation. White Foil open pit gold deposit is a low-grade deposit and therefore managing ore quality is a high priority. Ground movement through blasting can displace ore and waste boundaries up to 10 m from their in situ location and therefore requires stringent ore movement monitoring and adjustment. There are currently only two options for monitoring blast movement – utilising visual targets (commonly lengths of polypipe) but this has widely been replaced by electronic blast movement monitors (or BMM). Regardless of the technology used, the basic principle is to compare the pre- and post-blast locations of the targets to determine the movement of the rock mass during blasting, which is then used to determine the final location of ore and waste boundaries.The Blast Movement Technologies (BMT) BMM system has been used at White Foil since June 2014. The system has been effective and reliable during that time; however, the annual cost of using the BMM system is greater than other monitoring alternatives. As such, the open pit geology team conducted a study comparing the BMM system against the conventional polypipe technique. The objective was to quantify the profit and loss that would occur based on the ore block transformations from both methods. Eight blasts were selected where polypipes were installed in additional holes adjacent to the BMM monitoring holes. The resulting movement vectors from the respective methods were used to create post-blast ore blocks by transforming the in situ ore blocks. While polypipe is a cheaper alternative, the BMM system tracks ore and waste boundaries more effectively resulting in better quality control, enhanced ability to minimise dilution and ore loss thus maximising profit. For these eight blasts, it is calculated that the BMM system resulted in A$664 978 extra profit through a reduction of ore loss. The total cost of a yearly BMM package was recovered in the first two blasts of this study. The primary reason for the difference is that polypipe had a poor recovery rate of 32 per cent compared with 92 per cent for BMM at White Foil. Therefore, the data used to transform the ore blocks was less representative, resulting in inaccurate post-blast ore block boundaries when using polypipe.CITATION:Watson, M E, 2017. Blast movement monitors or polypipe? A study into cost-effective blast movement monitoring at White Foil gold mine, Western Australia, in Proceedings Tenth International Mining Geology Conference 2017, pp 433–440 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Sam Taoum, Omar Riahi

Few tools allow for accurately tracking ore dilution after blasting. Existing methods often rely on data analysis or linear interpolation of velocity, which can be imprecise and less effective in varied geological settings. A promising alternative is the use of numerical simulations, which involve complex mathematical calculations incorporating real physical data about explosives and geological characteristics. These simulations can model blast-induced fragmentation and subsequent ore dilution with greater accuracy, providing detailed insights into blast dynamics by considering factors such as explosive type, blast pattern, and rock properties. Numerical simulations integrate data from sources like seismic sensors, blast monitoring equipment, and geological surveys, offering a holistic view that single-method approaches cannot match. By simulating different scenarios, mines can predict the outcomes of various blasting strategies, optimize blast designs to minimize ore dilution, and maximize recovery. Advanced numerical simulations enhance the prediction of fragmentation distribution and size post-blast, crucial for effective dilution control and maximizing ore recovery rates.

Jan 21, 2025

By Enzo Angeles, Desmond Nanchengwa, Lee Julian, Julian Ruiseco

Since the early 1980s, surface hard-rock mining companies have searched for a blast movement model to enable grade control optimization efforts. Significant time and money were spent attempting to create blast simulations to aid post-blast grade control. Despite nearly 40 years of effort, practical blast movement models remained elusive until computing power reached levels that make real-time simulation possible. From the mid-1990s, mines have been creating in-situ grade control polygons and translating the polygon nodes horizontally to account for blast movement. In many cases, objects are placed in the blast volume and located post-blast to provide local vectors for these node translations. This method was always a compromise between practicality (2D) and reality (3D), but it was the only viable solution that matched the needs of operations. This study considers 21 blasts and evaluates the incremental value achieved by new processes unlocked through 3D modelling, while investigating challenges, limitations, and opportunities for each method.

Jan 1, 2023

By David E. Siskind

A Bureau of Mines survey of noise from quarry production blasting was conducted at seven crushed-stone quarries, providing information on close-in noise generation, comparative instrumentation, and evaluation of the sound levels as related to blasting parameters and existing State and local noise standards. The results from this preliminary survey will be useful in the design of a complete investigation of the problem of noise from blasting. There exists an immediate need for technical guidelines for noise pollution control agencies presently working on the regulation of impulsive noise sources. This survey and results from previous work by other researchers are used to derive interim recommendations on weighting scales, generated sound levels, and instrumentation. These recommendations are based on the limited data presently available and may be modified with subsequent investigation of noise generation, propagation, structural damage, and human tolerance.

Jan 1, 1974

By Benjamin Cebrian

Rock blasting at quarries represents multiple challenges not easy to see at first sight. Aggregate industries face similar or superior prices for explosives while extracting a material that usually is of less value of metal mining operations. Therefore, learning to optimize a quarry operation can be a perfect training for a position in blasting at larger metal mining operations.

Jan 1, 2010

By Peter Bellairs, Anthony Bubb

The Porgera Gold Mine is located at an altitude of 3000m in the central highlands of Papua New Guinea some 600 km Northwest of Port Moresby the capital city. Access to the mine is via a five hour trip on an unsealed road from Mount Hagen the nearest regional centre or 40 minutes via air. The mine operates on a fly in - fly out basis and currently produces ore from both opencut and underground operations with the former providing the bulk of the mill feed. Opencut mining utilises conventional truck / shovel, drill and blast methods on both 10 metre and 14 metre bench heights with the larger benches being restricted to the stripping areas. This paper presents the strategy used and the results of a blast optimisation process in the opencut that was a joint effort between the mine personnel and the explosives manufacturer/supplier.

Jan 1, 1997

Whilst employed by Dyno Nobel as the Technical Services Engineer û Brisbane, I was asked, as part of a contractual agreement, to look at optimising PioneerÆs blasting process to provide the most effective rock to the new crushing and screening plant. This paper details the preliminary blast designs and practices that have been in use at the quarry and the initial changes made to these designs, and the effect they have had on the excavation and crusher performance.

Jan 1, 1999

By D. Assmus, S. Daly

"Poor fragmentation, high toe areas, excessive shovel wear and tear and frequent re-drilling and blasting of certain tough waste rock zones in the Lomex pit in the early 1980snecessitateda better understanding of these zones.A combination of geotechnical mapping, penetration rate data, toe elevation contouring and observations on shovel and drill performance were used to determine the character and extent of these zones. This complementary information was brought together by the geotechnical mapper and the explosives supervisor.Distinct zones with particular geological characteristics were determined. A classification system with three types of blast and dig-ability was developed for the Lomex pit and later applied to the Valley pit, with considerable success. The three blast zone types are called ""poor"", ""f air"", and ""good"". This system will be described in detail.The explosives supervisor adjusted the blasting parameters to each zone, in particular, pattern spacing and burden. The resulting powder factors showed considerable variation between the poor, fair and good zones within each pit as well as between the two pits. Pattern geometry and length of collar were also adjusted to improve fragmentation. Cost savings resulted from less re-drilling and less wear and tear on drills and shovels in the poor zones and more efficient use of explosives in all the zones. An annual estimated cost savings of well in excess of $1,000,000 is realized at Highland Valley Copper. A by-product of the mapping was the determination of unstable structures and water flowing zones. Blasting was then adapted to this information for enhanced slope stability."

Jan 1, 1992

By Enrique Munaretti, Vitor Rosenhaim, Jair Carlos Koppe, Joao Francisco Feijo

The B3 mine is a multiple coal seam strip mining in operation in Rio Grande do Sul, the southernmost state in Brazil. A traditional truck & excavator operation is used to remove the overburden and selectively mine coal seams, ranging in thickness from 30 cm (1 ft) to 2.5 m (8.2 ft). Blasting is required in order to excavate part of the sedimentary rock overburden where the rock is too hard for mechanical excavation, and to mine the coal seams, selectively.

Jan 1, 2012